Search Documents

By S Basu, P M. Midhun

Electro-Slag Remelting (ESR) is a process capable of producing ingots with much lower centre-line segregation and better internal soundness than conventional ingot casting processes, as well as lower inclusion and sulfur concentrations. This process is commonly used for alloyed steels intended for critical applications like components of marine turbines, supercritical powerplants and rocket motor casings. It involves melting a metal electrode using electrical resistive heating in a slag pool and re-solidification of the resulting metal droplets beneath the slag layer, forming an ingot. Conventional ESR fluxes consist primarily of CaF2, Al2O3 and CaO, along with minor concentrations of SiO2, MgO etc. The emission of fluoride vapour from the molten slag causes several environmental and health problems, triggering a need to develop and reduce the fluoride content in the ESR flux. The present study aims to develop low-CaF2 alternatives to commercial ESR fluxes without compromising on productivity and the surface quality of the refined ingot. Thus, the modification in chemical composition needs to satisfy properties like electrical resistivity, viscosity and liquidus temperature, essential for efficient ESR operation. Since electrical resistivity and viscosity are highly dependent on the ionic structure of the molten slag, it is important to understand the effect of compositional modification on the structure of the flux. The present study employs Fourier-transform infrared spectroscopy (FT-IR) and Raman spectroscopy to investigate the structural variations in the modified fluxes, especially the effect of changing SiO2 concentration, in comparison with conventional CaF2-rich fluxes. Additionally, thermal analysis (Differential Thermal Analysis (DTA) and Thermogravimetric Analysis (TGA)) has been carried out to characterise the melting behaviour of the fluxes. The findings are compared with simulations carried out using the FactSage™ software, ver 8.3 (GTT Technologies, Aachen, Germany). Simultaneous analysis of liquidus temperature and the structure is expected to help in identifying the practical suitability of modified ESR flux compositions for industrial implementation.

Jun 19, 2024

By T Gartner

This paper describes the design, manufacture and site services associated with the supply of mine hoists for the new mine under construction by Falconbridge Limited in Ontario, Canada. Two new shafts are being sunk, and the hoisting equipment at each shaft can be summarised as follows: Ventilation shaft:4.66 m diameter double-drum second-hand hoist, originally in operation at San Manuel Mine, Arizona, to be used as the shaft sinking hoist. The second-hand hoist presented a challenge in that during its previous life, the hoist had been intensively operated during service at San Manuel Mine, and this paper describes the scope of refurbishment work undertaken, both electrically and mechanically, to ensure future reliable operation, together with the requirement to meet Canadian and Ontario regulations and codes of practice. 3.05 m diameter new single drum auxiliary hoist to be used as a second means of egress. Main shaft:4.57 m diameter new double-drum hoist to be used initially as the shaft sinking hoist, and subsequently to be converted to the equivalent of a single-drum multi-rope hoist for service duties during the production phase; 5.49 m diameter new double-drum hoist to be used for skip hoisting during the production phase; and 3.05 m diameter new single drum auxiliary hoist.The new hoists are all designed to comply with SABS requirements such that hoisting with reduced rope safety factors will be possible in the future. This paper describes the principles involved both mechanically and electrically. Particular attention is paid to the conversion of the main shaft service hoist from a double-drum sinking hoist to a multi-rope hoist.This paper describes the ac electrical powertrains (drives and motors) used that eliminate the need for harmonic filters and reactive power compensation equipment since they exhibit no negative effects on the utility electrical network system. This paper describes the logistical challenges of installing, commissioning and setting to work a series of five hoists in a short time frame.

Jan 1, 2005

By Percival T. J

Precious metal deposits containing fine-grained disseminated or dispersed gold-silver form by reactions between metal-bearing hydrothermal fluids and sedimentary host rocks. Host rock permeability and chemical composition exert a primary influence on the fluid movement necessary for any primary dispersion halos to form around ore bodies, and determine whether a disseminated style orebody itself will even form. Where the mineralized rocks are relatively unfractured the margins of the orebodies exhibit abrupt decreases in gold content, and strong corresponding decreases in the contents of other metals. Primary dispersion patterns of this type are difficult to recognize and commonly are only a few meters (or less) in width. If the host rocks were well shattered and broken before mineralization, remnant amounts of the hydrothermal fluids may be dissipated in fractures lateral to or above the ore zones. This causes geochemical anomalies to form with clays and silt- size silica within the fractures over distances of up to at least 30-50 meters away from the main orebodies. The tendency for large primary dispersion halos not to form around these deposits explains the disappointing results from so many drilling programs where no multi-gram gold-grade material was even found: if large areas and apparent large volumes of rock contain one gram or less gold that likely is the "orebody" and not a halo effect around high grade mineralization.

Jan 1, 1988

By R Engle, R P. McMahan, D A. Bowman, S Schafrik, W Thabet

Preventing injuries and fatalities related to conveyor system use in the mining industry is important and increases uptime while decreasing lost time. The research presented here is funded by the National Institute for Occupational Safety and Health (NIOSH), and intended to accomplish this prevention by the use virtual environments (VEs) to improve training and help miners better understand the hazards of working around conveyor systems. Two conveyor system VEs designed to teach miners about hazards and to safely complete tasks around conveyor systems were developed for this project. The first conveyor system VE, called the instructional tour, gives the miner a semi-automated tour of a conveyor system and teaches the miner about possible hazards (eg, missing guarding) and how to safely fix conveyor problems (eg, a stuck idler) using lock-out, tag-out procedures. The second, called the virtual shift, allows the miner to freely navigate around a conveyor system to detect and avoid hazards. The miner is presented with equipment failures that need to be safely repaired during the virtual shift. If the miner fails to identify and avoid a hazard or fix a failure in a safe manner, an animation of the consequences is shown to the miner, who must start the virtual shift over. The models for the conveyor system VEs were created using 3DS Max. Desktop versions of the VEs were then created using Deep CreatorÖ, an authoring application for creating interactive 3D environments. Later, more realistic versions of the VEs were created for CAVEÖ, a room-sized visualisation system, using DIVERSE, an application programming interface. In initial evaluations of the conveyor system VEs, mining colleagues have indicated great interest in such training tools. According to their feedback, these and similar VEs would provide excellent alternatives to normal classroom training and serve as positive precursors to hands-on experience. These VEs provide new miners a chance to experience hazards associated with working around conveyor systems without being in possible danger.

Jan 1, 2008

By S Ellis, J McMullen, M Habner

A new leaching regime was implemented at Kalgoorlie Consolidated Gold MinesÆ (KCGM) Gidji plant on a cyanide leach of ultra-fine ground sulfide concentrate. High lime concentration and lead nitrate were used to overcome the refractoriness of the fine sulfides (high reactivity of fine sulfides with the presence of gold tellurides). The leach pretreatment stage was shown to be detrimental and was shut down. Lime titration was introduced as part of the process control. It was shown that the leach could be performed at low dissolved oxygen, (ie 3 - 5 ppm) to avoid sulfide oxidation and the associated high cyanide and lime consumption. Plant results showed reduced cyanide consumption (40 per cent) and an accelerated leaching rate, whereby most of the gold was dissolved in 24 hours compared to 72 hours used previously. Similar work was performed at KCGMÆs Fimiston plant, which leached a combined ultra-fine ground sulfide concentrate along with the slimes fraction from hydrocycloning the bulk flotation concentrate. The use of lead nitrate, high lime and carbon-in-leach generated a faster leaching rate and minimised adsorption of gold on fine pyrite particles. The grind, previously controlled with a P80, was replaced by a P98 to give a better operational indication of top size hydrocyclone performance. Before the implementation of the changes, average leach residues for slimes and UFG were respectively 4.0 g/t and 5.5 g/t. With the modifications to the leaching regime, average leach residues were lower by 1.5 - 2.0 g/t. Whilst significant improvements have been demonstrated, further work is progressing at KCGM to further reduce ultra-fine concentrate leach tail grades, and also to improve the understanding of concentrate refractoriness and the factors responsible for differences between laboratory and plant leach results. Estimated profits since the implementation of the new approach are in the range of $A3.5 million per year.

Jan 1, 2005

By N Van Buc, E Coroiu

The rapid socio-economic growth of Hanoi City coincides with a corresponding growth of the transport demand. Today, the transport in Hanoi is completely dependent on private modes of transport. Because of the lack of an efficient public transport system and the expected rapid increase in traffic volumes, the movement of people and goods in the urban areas of Hanoi will cause congestion in the present city transport network. The solution of the construction of new roads, or the widening of the existing streets, is very expensive in urban areas and usually causes many social problems due to the resettlement of people. From the point of view of the number of inhabitants, Hanoi City is now over one million. Above this number the international experience shows that the public transportation must be a mass transport system with large capacity, commercial speed and also independent as much as possible from the street network. According to the Hanoi Master Plan for 2020, the Hanoi urban population will be over 3.5 million persons. Also, in the next 15 years, the distances between centre-destination points will be doubled by comparison to 1995.

Jan 1, 1999

By P R. G Milne

A risk-based approach to optimising pit wall slope angles was trialled in the design of a 60m deep open pit in extremely weathered and distinctly weathered materials in the Kalgoorlie area. The pit used for this approach was Stage 1 of a three-stage open pit project. The Stage 3 pit will require long term stability, as it will contain the portal for a long life underground project. Information from failures induced by steeper wall angles used in the Stage 1 pit would be valuable in predicting and preventing long-term stability issues in Stage 3. In this approach, the pit wall slopes are based not on the normal factors of safety, but on the assessment of the probability of failure and the direct and indirect costs of dealing with the failure when it occurs. In this example, the benefits and risks of adopting steeper wall angles were compared in a series of graphs. These charted the increasing probability of failure and simultaneous decreasing factors of safety with increasing pit wall slope, and the range in the possible volumes of circular failures for increasing wall angles. These were brought together in a graph showing the potential excavation savings (in BCM) and the probable cost of a failure (probability of failure times the probable volume of the failure). The resulting pit design was based on the project Mining EngineerÆs semi-quantitative assessment of where and when a higher risk of failure was acceptable and where it was not acceptable as it may have unduly affected the integrity of haul roads or production. The design incorporated wider than normal berm widths to accommodate anticipated failures and to enable modification of the wall configuration if required. Several re-designs were required during the life of the project in response to aggressively induced failures. It is considered that this risk-based approach provides a practical route to optimal pit design and operation but it requires an experienced, dedicated and efficient mining team for it to be implemented with benefit.

Jan 1, 2003

By P Duuring

Late-Archean banded iron formation (BIF)-hosted deposits in the Yilgarn Craton of Western Australia are less well understood compared to the larger Paleoproterozoic, Superior-type BIFhosted deposits of the Hamersley Province. The Weld Range greenstone belt, in the Murchison Domain of the Yilgarn Craton, hosts two Archean, high-grade deposits, Madoonga (68 Mt resource at 57.7 wt per cent Fe) and Beebyn (62 Mt resource at 59.6 wt per cent Fe, ASX announcement 2008). Five main types of high-grade (>55 wt per cent Fe) iron mineralisation at Weld Range each display characteristic grades, tonnage, and contaminant levels, which affect exploration strategies and beneficiation methods:1. ‘Residual’ ore formed as a result of two generations of hypogene alteration of BIF. The first alteration phase replaced silica-rich bands with siderite and/or Fe-rich dolomite; the second phase involved the removal of carbonate gangue minerals and the concentration of residual Fe oxide-rich bands in the BIF via volume reduction. The product is a high-grade, high-tonnage Fe orebody, with minor contaminants.2. Magnetite-bearing shear and fault zones cut BIF along lithological contacts. These zones of secondary magnetite formed as a result of the addition of hypogene magnetite via the circulation of Fe-rich, hypogene hydrothermal fluids through BIF. This type of mineralisation produces narrow (low-tonnage), high-grade magnetite-rich ore zones with high levels of contaminants (eg SiO2, Al2O3) due to the difficulty in mining these zones.3. Specular haematite ± quartz-bearing shear and fault zones cut residual orebodies and magnetite bearing structures. They share similar characteristics to magnetite-bearing structures.4. Goethite-haematite supergene ore zones are controlled by brittle faults that cut BIF. These faults promoted the flow of supergene fluids through BIF and resulted in large ore zones with variable Fe grades and contaminants.5. Detrital deposits comprise transported BIF fragments and are intensely goethite-haematite supergene-altered. These orebodies are locally extensive, with moderate Fe grades.

Jul 11, 2011

The introduction of cement into underground backfilling at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited mines to improve mining efficiencies gave rise to several major problems, the magnitude of which had not been anticipated. These problems were 1. A loss of recovery in the milling circuit due to the presence of cement 2. The presence of cement-rich slime layers on the surface of the fills 3. The introduction of a safety hazard due to the slippery nature of the surface of cemented fills 4. The deposition of cemented slimes on the levels and in underground sumps and dams. The loss of revenue due to decreased metal recoveries considerably offset the gains from increased stoping efficiencies and the use of cement was substantially reduced while, (a) the Metallurgical. Department attempted to identify the chemical nature of the problem and overcome it, and (b) the Mining Department investigated methods of reducing cement contamination of the ore stream. As a part of this investigation the Mining Department added polymeric flocculants to the cemented fill pulp. Testwork was carried out in the following steps 1. The available Alfloc polymers were screened to determine which was the most effective and what was its optimum dosage rate. 2. This polymer was used in the laboratory to determine the reduction of surface slime, clarity of water, and effects on strength and percolation of fill. 3. Fills were placed underground to substan- tiate the laboratory work. /+. The polymer was then added to all cemented fills going underground to study its effect over a long term. The use of flocculants not only improved the distribution of cement in the body of the fill, but also the distribution of the fines fraction of the filling material, practically eliminated slippery surfaces and improved the clarity of the drainage water. Flocculant is now added to all cemented fills and restrictions on the use of cement are gradually being lifted.

Jan 1, 1973

By G R. Hancock, M J. Saynor, J B. C Lowry, T J. Coulthard

Landform evolution models (LEMs) can assess the effectiveness of landform designs applied to a rehabilitated landform by predicting where erosion may occur. Here, we compare erosion predictions produced by the CAESAR-Lisflood LEM with field observations from the rehabilitated Pit 1 landform of the Ranger uranium mine, based in the Northern Territory, Australia (Figure 1). The ability to predict long-term erosion at a catchment scale is important, as the final rehabilitated Ranger landform is required to physically isolate buried tailings material for at least 10 000 years. CAESAR-Lisflood has been extensively tested and calibrated using data collected from erosion plots (0.09 ha) on the Ranger trial landform (TLF) for multiple years (Lowry et al, 2020; Saynor, Lowry and Boyden, 2019). However, until recently, it was impossible to compare model predictions with field observations for areas larger than the TLF erosion plots. We can now compare model predictions of Life of Mine Conference 2023 | Brisbane, Australia | 2–4 August 2023 116 gully development with field observations from the newly rehabilitated, 40 ha surface of Pit 1 over two contiguous one-year periods: 2020–2021 and 2021–2022. The aim of this study was to assess whether the CAESAR-Lisflood model can successfully predict gully erosion at a larger spatial scale.

Aug 2, 2023

About 60 persons are admitted to the graduate course every year after passing the entrance examinations. The entire course of studies is free of charge and the universities provide accommodation for the students who need it. The five years of studies are divided into 10 semesters. One semester lasts 15 weeks. Automatics can be studied at three separate faculties. At the University of Mining and Metallurgy, it is offered by the Faculty of Electrical Engineering, Automatics and Electronics as well as the Faculty of Mining and Metallurgical Machines (metrology can also be studied there); at the Silesian Technical University in Gliwice, the Faculty of Mining offers the course. The educational plans and programmes comprise 3 groups of subjects: common for a given course of studies (foreign languages, political science and the basic technical knowledge) common for the speciality and subjects of diploma courses. The whole time of studies covers about 4400 hours excluding 3 periods of professional training and the physical training. The classes, laboratory classes, seminars and design classes are obligatory and the attendance is strictly checked. Students may extend their knowledge by participating and working in the Science Clubs. The students' work is checked not only during the classes but also by the examinations held at'the end of respective semesters. Those who fail the exams can repeat them only if very important reasons are presented. At the very end of the studies there is a diploma examination together with a discussion on the diploma thesis, written by the student. The successful result entitles the student to recieve the title of "magister inzynier",M.Sc. of his speciality. The graduates, after working for 2 years, can attend another course of studies lasting 2 semesters and called "Postgraduate Course", or start "Doctoral Studies" finished by the defence of a doctor's thesis. In'these cases the expenses are usually covered by the graduates' employers.

Jan 1, 1985

Structural geological modelling is a process which results in a 3D computer model that represents the essence of the geological and structural understanding of an area and is presented in a way that is directly useable, typically by internal customer groups. BHP Iron Ore operates a number of open cut iron ore mines in the Pilbara Region of Western Australia. The largest mine is the Mt Whaleback Mine located at Newman close to the southern margin of the Pilbara Craton. The structurally complex Mt Whaleback Mine is the largest metalliferous single pit open cut mine in Australia with over 1.6 billion tonnes of original iron ore resource. Additional to the Mt Whaleback Mine, a number of satellite open cut iron ore mines are operated by BHP Iron Ore (BHPIO) in the Newman area. BHPIO also operates the Yarrie mine approximately 400 km north of Newman at the northern edge of the Pilbara Craton Most of the BHPIO mines are located in the Archean- Proterozoic Hamersley Province that overlies the Archean granite-greenstone terrain of the Pilbara Craton. The orebodies are considered to be the result of supergene enrichment of the approximately 2.5 Ga Brockman Iron Formation and the slightly older Marra Mamba Iron Formation. Folding represents the most prevalent and penetrative structural element in the Newman area. Four folding phases have been identified regionally (Fj, F2, F3, F5), while a more local folding deformation (F4) developed mainly in the Mt Whaleback and Orebody 29 mine area. A northeast trending, southeast dipping, 45 km long, high angle, normal fault zone, the Whaleback Fault Zone, cuts through the Mt Whaleback mine resulting in an approximately 1400 in gap in stratigraphy. Additionally, two large, low angle, normal faults, the East Footwall Fault and the Central Fault, are present at the Mt Whaleback Mine. During the formation of supergene orebodies, up to 40 - 45 per cent volume loss occurred resulting in local non-tectonic deformation in the orebodies.

Jan 1, 1997

By Hatherly P, Luo X, Balusu R, Gale W

Ongoing, collaborative research between CSIRO's Exploration and Mining and Strata Control Technology has resulted in a better understanding of rock failure mechanisms around longwall extraction. Failure has occurred further ahead of the retreating face than predicted by conventional longwall geomechanics theory. In some cases significant failure has been detected several hundred metres ahead of the face position with demonstrated influences of minor geological discontinuities. Shear, rather than tensile failure has been the predominant failure mechanism in the environments monitored. Validating technologies of microseismic monitoring and new face monitoring techniques have assisted the development of predictive 2D computational modelling tools. The demonstrated 3D consequences of failure has assisted in the ongoing direction of the project to further investigate these effects.

Jan 1, 1998

A laboratory investigation was carried out to obtain data on the explosive character- istics of selected coals mined in New South Wales. Seven coal seams were sampled and the volatile matter content of the coals tested varied between 28 and 37 percent. A mod- ified Hartmann apparatus with a volume of 1250 ml was used in the investigation. Dust clou' generation was produced by an air blast delivered radially through a mushroom type valve and the ignition source was a-continuous A.C. spark produced by a 20 000 V, 50 mA transformer. The coal dust parameters invest- igated were the maximum pressure developed, the average and maximum rates of pressure rise at dust concentrations between 200 and 1500 3 g/m.

Jan 1, 1981

By Woodcock J. T, Rummel P. H, Sparrow G. J, MacRae C. M

An automated method, which is believed to be the fastest in the world and which can be used by mineralogically-untrained technical assistants, has been developed for the rapid location of native gold particles and other gold minerals down to 1 pm in size in ores, concentrates, and tailings using a scanning electron microscope. Searching of a 25 mm diameter polished block in 1 pm steps usually requires 3-4 h. Examples of the location of native gold and gold tellurides in drill core sections, in crushed ore samples and gravity and flotation concentrates, and in various metallurgical test products are given. The results have application in ore exploration, in guiding metallurgical test programmes, and in assessing metallurgical per- formance in testwork and in operating plants.

Jan 1, 1991

By Tilley J. L, Chicu D

The development of the Yallourn East Field brown coal open cut has involved the adoption of novel investigational programs into coal qual- ity. For example, weighted average coal property statistics for key proper- ties are determined by using a unique blend of traditional and 3-dimensional geostatistical estimation. Predicted property values are made freely available from the mainframe computer in the form of kriged esti- mates of 60 000 tonne coal blocks. Geostatistical predictions are being incorporated within the Mincom/Intergraph CADD system which is used for mine design. Key properties relating to coal type, moisture, and ash have been evalu- ated to provide the required data for the design and operation of both the open cut and the power stations as well as the briquette plant.

Jan 1, 1989

Mount Isa mine is the largest underground mine in Australia and is located 2,000 kilometres north-west of Brisbane. This mine has been in continuous operation since 1931 and in 1986/87 the silver/lead/zinc stream achieved the peak annual mining rate of 4.7 million tonnes. At present about fifteen different steeply dipping stratiform orebodies are being mined to maintain an annual production rate of around 3.0 million tonnes. Out of these, only two orebodies (2 & 5) are amenable to sub level open stoping (SLOS) type bulk mining methods. This year only 150,000 tonnes are scheduled from pillars and remnant areas but in future, more sources will be required to meet the budget production targets.

Jan 1, 1990

By Andersen AK

A previous paper (1) indicated that electrowinning of copper at current densities considerably higher than those currently employed in electrowinning operations is technically feasible. It is of interest, therefore, to establish the extent of economic benefits which may be obtained from high current density operation and to determine the value of the optimum current density. Optimization of electrorefining processes has been discussed in considerable detail by Ibl (2) and Schmidt (3) whop from theoretical considerations, derived expressions for the optimum current density. In this work, general equations relating both the capital investment and the production cost for copper electrowinning plants to current density and plant capacity are established. From these equations, the optimum current density can be calculated for any desired plant capacity.

Jan 1, 1969

By Jackson E

The general level of awareness amongst members of the professions that they are faced with an increasing number of claims for breaches of their professional duty was dramatically heightened by the decision of Rogers J. at first instance in Cambridge Credit Corporation v Hutcheson (1985) 3 ACLR when the auditors of the failed company were found liable for breach of contract and faced a damages award of $145 million - well in excess of their insurance cover. No comfort should be found in the fact that this decision was overturned on appeal, for that result rested on the issue of whether there had been a causal connection between the breach of contract which had occurred and the loss suffered rather than on the fundamental principle of auditors' liability.

Jan 1, 1989

By Gang L

Seventy-nine gold deposits and prospects have been discoveried in the Jiamusi region of northeast China, and constitute one of the most important gold metallogenic belts in China. All these endogenic gold occurrences can be subdivided into three main deposit types: (1) porphyry related; (2) metamorphic-intrusive hosted, and (3) sediment-hosted deposit. The first two types of gold deposit are spatially and temporally related to Mesozoic Yanshanian granitoid intrusions with hydrothermal activity channelled along crustal-scale fissures. The ultimate cause of the Yanshanian magmatism is considered to be the subduction of Pacific oceanic lithosphere beneath the Eurasian continent. In contrast, The chemical sediment-hosted deposit is typified by the Dongfengshan gold deposit, and genetically related to Proterozoic sedimentation and Mesozoic igneous activities.

Jan 1, 1995