Search Documents

By A. M. Gaudin

THE so-called Kick law' is generally accepted to . mean that for each reduction to one-half in particle diameter, in a unit weight, the same amount of work is required. In crushing-efficiency calculations on crushing tests it is customary, when basing the calculation on Kick's law, to assign ordinal numbers to each standard sieve size. These ordinal numbers increase by a constant difference with each successive sieve aperture, because standard sieve apertures are in constant ratio. Minus 200-mesh is generally assumed as equivalent to 37 microns in size. By definition, the ordinal number multiplied by the per cent material of any size is equal to the energy units in the material of that size in a unit weight of sample. The sum of all energy units is the energy units content of a unit weight of sample, whether it be crusher feed or product. The difference between the energy units in the product and that in the feed is the tangible result of the work input per unit weight of feed. From this the amount of work necessary for one energy unit may be calculated. This has been done for a quartz crushing-test made at the Intermountain Experiment Station of the U. S. Bureau of Mines at Salt Lake City, in which the net work going to crushing was carefully measured. The results of this crushing test are given in Table 1.'

Jan 1, 1929

By H. M. Beatty, T. L. Joseph, Gust Bitsianes

SUCCESSFUL blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blast- furnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO ? 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which C02 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature com- bustion of carbon above the tuyeres. Assuming that 1000 lb. of limestone is used per ton of pig iron, about 435 lb. of C02 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb. would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1942

(The following list contains the names of those members of the Institute of whose connection with military service we have only recently become acquainted; it also includes the names of a few who have recently been promoted or transferred, indicated by a *. A complete list was published in the Year Book, issued as a supplement of the Bulletin for March, 1918.) *AMBLER, HARRY A., 1st Lieutenant, 0. R. C., 30th Infantry, A. E. F. BAKER, R. F., Private, Intelligence Section, Headquarters 90th Division. *BARTON, L. A., Captain, 604th Engineers. *BATTEN, H. L., Lieutenant, Canadian Engineers, C. E. F. *BENSEL, J. A., Major, U. S. Reserves. BIRKETT, HOWARD, Lieutenant, Aviation, U. S. Signal Corps. BLOOMFIELD, E. C., Lieutenant, 1st Canadian Tunnelling Co. BOOTH, L. E., Watertown Arsenal, Det. E. 0. C., N. A., Watertown, Mass. *BOWMAN, REGINALD G., 1st Lieutenant, Engineers, U. S. R., Int. Ord. Dept. No. 4, A. E. F. *BRADLEY, CLARENCE I., Convois Automobile Section 585,. S. S. U., P. A. R., B. C. M.

Jan 7, 1918

By C. G. Dunn, P. K. Koh

Microstructure, magnetic torque, and texture data before and after grain growth were obtained on two 3.25 pet Si-Fe specimens having initially the same cold-rolled textures and the same primary recrystallization textures. The latter textures consisted of four components, two only of which were strong; the strong components were near (120) [001] and (320) [001]. The textures of the two specimens obtained by grain growth were different. In one specimen the two weak components were converted into strong components by a secondary recrystallization process; in the other specimen the primary recrystallization texture was retained by a normal grain-growth process. The difference in behavior of the two specimens was interpreted in terms of a difference in the relative grain sizes between weak and strong components; i.e., in terms of a geometrical factor that would alter the early growth rates of grains belonging to the two weak components of the texture. Specifically the growth rate was considered as the product of two terms: a driving force and a boundary mobility. The texture changes observed are considered to favor the oriented-nucleation growth-selectivity theory more than the oriented-growth theory. WHEN primary recrystallization and grain-growth textures form as a result of annealing deformed metals or alloys, the fundamental processes involved are nucleation and growth. Knowledge, therefore, about nuclei and the factors influencing their growth is required not only for the understanding of texture development but also for its control. In the oriented-growth theory of texture formation1, 2, 3 the problem of nuclei is generally disposed of by the assumption that nuclei are available in all orientations; the theory then has to explain the final texture from the initial texture and the way boundary mobility depends on orientation. In the oriented nucleation theory of texture formation"' nuclei are considered to be present only in certain orientations but the importance of growth selectivity is still recognized. For example, the mobility of boundaries of approximately the same orientation and of the coherent type in twins is believed to be low while that of high-angle boundaries, in general, is high. Because of this the theory may be described as an oriented-nucleation growth-selectivity theory. The main feature of the oriented-nucleation theory, however, is the importance given to nuclei; i.e., how they form in specific orientations and how they grow. In the present investigation two cold-rolled single crystals were used to study the effects of growth after primary recrystallization. The cold-rolled textures and the primary recrystallization textures were determined from portions of these specimens and reported earlier.",' The two cold-rolled crystals were in the (111) [112] stable end orientation, the recrystallization textures were nearly identical and consisted of two strong components, designated M and M', which were near (120) [00l] and (320) [00l], respectively, and also some specific weak components near (111) [110] and (111) [110]. It is well recognized that a single strong component in the primary recrystallization texture may be needed for secondary recrystallization3, 5, 8 but unfortunately when this is the case the amount of material left in deviating orientation may be too small either for growth or for positive identification. The present samples proved to be almost ideal for the study of minor components and their influence on texture changes produced by growth after primary recrystallization. The results obtained are interpreted in terms of present knowledge of grain-growth processes. Experimental Procedure Two lots of silicon-iron alloy of essentially the same composition, namely, 3.25 pet Si, 0.004 C, 0.009 P, 0.010 S, 0.035 Mn, 0.070 Ni, 0.090 Cu, 0.009 Sn, with traces of A1 and Cr and the balance Fe, were converted into single crystals 0.025 in. thick and 1.25 in. wide. The orientations were predetermined by the method of reorienting a seed crystal as described elsewhere.3 pecimen 1 from one lot had the (335) [556] orientation while specimen 2 from the second lot had the (111) [112] orientation.* Both crystals were cold rolled to a reduction in thickness of 70 pet while widening approximately 20 pet. Samples of each were selected for determining 1) the cold-rolled texture, 2) the time required at

Jan 1, 1959

By G. R. Belton, Y. K. Rao

A galvanic cell, using liquid MgCl2 or MgC12-CaC12 mixtures as the electrolyte, has been used to determine activities in Mg-A1 liquid alloys between 700' and 880°C. The incovporation of a chlorine electrode in the cell also allowed measurements to be made of the standard free energy of formation of MgCl2(l). The results are shown to be in good agreement with thermo-chetrlical values from the literature, and this is taken as evidence that the small, known solubility of magnesium in iMgCl2 introduces no significant error in galcanic cell measurements. Within experimental error, the activity coefficients and relative partial molar enthalpies at 800°C are shown to be represented by the following "subregular" solution equations: logy~~ =-0.68(1 -xMgj3 log yAL =-1.02(1 - XMf + 0.68(1 - XMf H.M = -4400(1 - %)3 / cal Mg 7Ag' HZ =-6600(1 - xA1)' + 4400(1 - XMf cal SCHNEIDER and toll' have used a transpiration technique to measure the vapor pressures of magnesium over Mg-A1 alloys between 544" and 594°C. amsstad,' however, has since suggested that the extrapolation to zero flow rate, used by these authors in interpreting their apparent pressure vs flow rate data, gives unreliable results. Rogers, Tomlinson, and Richardson,3 in interpreting the results of solution equilibria between Mg-A1 alloys and liquid MgC12, also considered the measurements of Schneider and Stoll to be unreliable and preferred to derive activities for the alloys from the earlier boiling point determinations of ~eit~ebel~ and the partial molar heats recommended by Kubaschewski and ~atterall.~ These latter heats were based substantially on the early calorimetric work of Kawa-kami but, unfortunately, his work on other systems has sometimes been found to be inaccurate.7 Rogers et al., in the above-mentioned paper,3 tentatively concluded that the most likely species responsible for the limited solubility (0.3 mole pct at 800°C) of magnesium in MgC12 were Mg° (neutral) and Mg2++. Two more recent studies8,9 have supported Mg2++ as the soluble species. In the present study, activities in Mg-A1 alloys have been determined by means of a galvanic cell involving liquid MgCl2 or MgC12CaCl, mixtures as the electrolyte. Since the reactive nature of magnesium precluded simple Faraday yield experiments, a chlorine electrode was incorporated in the cell in order that the performance of the cell could be checked by measurements of the heat and free energy of formation of MgC12. This procedure was considered necessary since it has been suggested1' that the solubility of a metal in a molten salt might introduce electronic conductivity; also, previous determinations of the standard electrode potential for MgC12 differed by as much as 70 mv11-13 EXPERIMENTAL Materials. Analyses of the materials used in preparing the alloys and the electrolyte mixtures are presented in Table I. The alloys were prepared by induction melting weighed amounts of the metals in a graphite crucible held under an argon atmosphere. Pure anhydrous magnesium chloride was prepared by heating the mixture MgCl, . 6H20 +NH4C1(1:1) to 650°C, followed by melting under dry argon. The melting point of the dry MgC12 was found by differential thermal analysis to be 714.8oC, which compares well with the accepted value of 714C.14 This agreement was taken to be an indication of the high purity of the dried salt. Table I. Compositions of Materials, wt pn Impurity Mg Al MgCI2 CaCI, Ba - - 0.005 Ca - - 0.010 Cu 0.02 0.02 Fe - 0.10 0.001 0.010 Pb 0.01 - 0.001 0.005 Mn 0.15 0.001 Si - 0.10 Sr - - 0.005 MBSO* - 0.040 ARGON TUNGSTEN CHLORINE LEAD—411 11 II ALUMINA 'A I / ave GRAPHITE on irA~_ ( ^"l ROD MAGNESIUM S>ILICA~^ /, OR ALLOY-. I /A] ___________ -«^- _ ELECTROLYTE I y FRITTED DISCS Fig. l—Arrangement of chlorine and metal electrodes in electrolytic cell.

Jan 1, 1970

[ ]

Jan 1, 1938

By C. Feng, W. E. Krul

A study was made of the development of texture and the anisotropy in plastic flow of Ti-8Al-1Mo-1V alloy. Based on Pole figure determinations, the shifting of texture induced by rolling at approximately 400°C was found to be due primarily to slip rotation for the major Portion of the material. Grain boundary shear is believed to be an important factor. The anisotropy of the textured alloy was examined in terms of the variations of yield stress under tension and the ratio of bi -axial strain increments µp, in the temperature range 25" to 290°C. The results were related to Hill&apos;s theory on plastic anisotropy. The Schmid factors of (1100)[1120], (1101)[1120/, and (1101)[1120] slip systems were analyzed and found to be compatible with the observed anisotropy. Cross-slip between these planes was proposed as a possible deformation mode. In a number of published articles, considerable interest has been directed to the possible achievement of texture hardening in hcp metals. Following Backofen, Hosford, and Burke,&apos; this phenomenon was related to the yield criteria of the material and was expressed in terms of the biaxial strain ratio, r = d?w/d?l. The higher the value of r, the greater is the expected potential for texture hardening under certain loading conditions. For a given material, r varies with direction. Such variation can be traced to the anisotropy in plastic flow and can be explained within the framework of the various modes of deformation. Hatch2 found that a high r value coincides with a texture whereby the (0001) pole is closely aligned with the surface normal for sheet materials, Based on the analysis of the slip on the {1010}, {1011}, and (0001) planes, Lee and Backofen3 and Avery, Hosford, and Backofen4 concluded that the resistance to thinning is reduced by the operation of the (0001) <1120> slip system; with this reasoning they were able to explain the low r values (i.e., r « 1) observed in magnesium alloy sheets in the rolling direction and in commercially pure titanium in the transverse direction. The general equation, dealing with plastic flow in a polycrystalline aggregate has been used to correlate the plastic anisotropy and texture. In this expression, T and s are shear and normal stresses, and dri and d? are shear and normal strain increments, respectively. Assuming that five slip systems are operative within each grain and applying the principle of maximum work,5,6 one can determine the m value among the available systems. On this basis, Hosford7 and Chin, Nesbitt, and Williams&apos; were able to correlate m with yield stress under plane-strain compression, and Svensson9 was able to predict the variation of yield stress in textured aluminum. These workers made their analyses from materials in which slip operation is known to be associated with plastic flow. Questions remain regarding the derivation of Hill&apos;s theory on plastic anisotropy,10,11 since it was formulated on von Mises&apos; yield criterion.&apos;&apos; Its ability to deal with other forms of deformation has been in doubt.13 Others have discussed the validity of Hill&apos;s quadratic equation relating strain and yield stress.14&apos;15 For hcp titanium, deformation by various modes of slip and twinning operations has been reported.16-20 If all possible modes of deformation operate and contribute substantially to the plastic flow, it is difficult to imagine how the quadratic expression can suitably describe the anisotropic plastic flow of titanium alloys. Backofen and Hosford15 considered that Hill&apos;s is a macroscopic theory and implied that the major mode of deformation by slip mechanism will adequately describe anisotropy of the material. In the present investigation, slip operation will be shown to play the major role in the development of sheet texture induced by rolling of a commercial titanium alloy. Although twinning and other modes of deformation may also operate, their operation is believed to be secondary. The anisotropic properties of the sheet, which can be expressed in terms of directional variation of r, µp = -d?w/d?l and the yield stress will be shown to be governed primarily by slip operation. MATERIALS AND EXPERIMENTAL TECHNIQUES The titanium alloy chosen for the present investigation had a nominal composition of 8 wt pct Al, 1 wt pct Mo, 1 wt pct V, and 0.1 wt pct interstitial impurities. Sheets varying between 0.1 and 0.15 in. thickness were used. The alloy was received in a condition which was prepared by rolling at 900°C and annealing at 700°C. Subsequently, the sheets were subjected to further reduction in thickness by rolling at 400°C. A total reduction in thickness of 65 to 70 pct was obtained by a series of quick passes in a rolling mill with intermediate reheating. Further reduction in thickness was not possible due to cracking developed at the edges of the sheets. X-ray measurements were conducted in a Siemens and a Norelco unit to determine the texture of the sheets. Reflection techniques were used exclusively with CuK, radiation and a nickel filter. The loss of X-ray intensity due to geometric defocusing was calibrated with a technique described previously." The (0001), (1010), and (1071) pole figures were plotted from 0 to 80 deg, and to present the texture elements quantitatively, inverse pole figures were constructed following the technique described by Jetter, McHargue, and Williams.22 Tensile experiments were carried out at 25", 175",

Jan 1, 1970

By W. L. Saunders

THE world&apos;s greatest producing area is, geographically, in the midland region of North America about the Great Lakes. This area, with but one- third of the nation&apos;s population, produces, with the exception of tobacco and cotton, three-quarters of the principal staples. It provides the surplus or export grain, meats, dairy products, steel and leading minerals. The social and political condition of a nation is determined by its industrial efficiency, and the share of the commerce of the world obtained by a nation is fixed more by the economy of its transportation than by any other factor. It is an economic maxim that: The total cost is the cost of production plus transportation cost. The cost of carrying 1000 tons by water or 100 tons by rail is equal, over the same distance

Jan 1, 1921

Jan 1, 1883

By WILLIAM COUPER

THE completion of the excavation of the tunnels through Bergen Hill for the extension of the Pennsylvania Railroad into New York City, together with the fact that the excavation for the rest of the tunnel-line has been practically completed for some time past, arouses sufficient interest to justify a description of the engineering- and contracting-work, and the organization by which it has been accomplished. The finishing of the excavation is a long step towards the completion of the entire tunnel-project. It will be interesting to the members of the Institute, who last spring were taken through a great part of this work, to know that by the excavation now completed it is possible to walk by tunnel from a, point near Sunnyside yard, Long Island, east of the 34th Street ferry, to the central passenger station site in the City of New York, and thence by tunnel to the Hackensack meadows, and by an embankment constructed across these meadows to Newark, N. J. This New York tunnel extension is being constructed as a part of the Pennsylvania Railroad system by the Pennsylvania Tunnel & Terminal R. R. Co., a corporation of the States of New Jersey and New York. It extends from a point near Newark, N. J., to the Sunnyside yard, Long Island, as indicated on the accompanying plan.

Jan 7, 1908

By J. E. Tobey

BECAUSE of the wide-spread publicity given to Nylon yarn as being made from ?coal, air, and water,? the general public has become conscious of the nonfuel uses of bituminous coal. Some of these uses are as filler for fertilizer, carbon for the absorption of orders, for water supply, and for the bedding of cattle. Spectacular as are these accomplishments the fact is that only a small amount of coal is used for nonfuel purposes. It is on the utilization of coal as fuel that the industry depends. Practically all the coal mines for years to come will be used for making coke for the generation of heat. Recently much attention has been paid to the significance of ash in coal. Another study worthy the interest of metallurgists in the iron and steel industries if that of Dr, Lowry of the Carnegie Institute of Technology relative to the percentage of sulphur in coal and coke.

Jan 1, 1941

By Malcolm J. McPherson, Michael Hood

Sunnyside Mines, owned and operated by the Kaiser Steel Corporation, are situated near the city of Price, Utah. The complex comprises three adjacent mines, named simply Nos. 1, 2 and 3, all connected underground. Two seams, the upper and lower Sunnyside have been worked. These dip at about 10 percent to the north-east. The surface cover is variable due to the mountainous nature of the topography. The Sunnyside upper seam varies from 5 1/2 ft (1.7m) to 9 ft (2.7m) In thickness whilst the lower seam remains at about 6ft (1.8m). The separation between the two seams has ranged from 7 to 45 ft over the mined area (2 to 14m). Longwall mining has been practiced at Sunnyside for over 20 years due to difficulties of roof control encountered when using the roan and pillar system. Number 3 mine is bounded on the north and south sides by mines Number 1 and 2 respectively. Whilst current production is concentrated into Number 1 mine, much of the future of the complex lies in the further development of deeper reserves in Number 3 mine. Workings in this latter mine were curtailed in 1978 due to difficulties in ventilation. Present developments are ventilated partially from the neighboring Number 2 mine where no workings are in progress. The layout of Number 3 mine is illustrated on the schematic Figure 1. Trunk airways extend down dip from the surface at No. 2 Canyon and the Water Canyon for a distance of some 9,600 ft. (2930m). The area between the two sets of trunk airways has been worked extensively in both seams as have the corresponding reserves on either side in the connected adjacent mines. At the present time exhausting fans are sited at the top of a shallow shaft in No. 2 Canyon and an 8 ft (2.4m) diameter shaft sunk to a depth of 1013 ft (310m) closer to the current developments (Figure 1). The current airflow system, even with an additional 116,000 cfm (55m3/s) entering from No. 2 Mine, is adequate only for the development work now in progress but will be unable to support new longwall faces further downdip. The basic ventilation problem of this mine may be stated quite simply. In a situation where all intake and return airways pass through extensive old workings, a ventilation system design was required that would be effective, efficient and economic for the foreseeable future of the mine. ORGANIZATION OF THE PLANNING PROCEDURE The procedure followed during the study is illustrated on Figure 2. Initial ventilation surveys established the current state of the airflow system and provided the necessary data for setting up a Basic Network File in a computer store. The data in this file was a mathematical model of the ventilation system of the mine. The basic network was analysed by a ventilation network analysis program in order to correlate the measured and computed airflows and to establish the basic network as a true representation of the mine as it stood at the time of the surveys. The network model could then be extended to simulate the future development of the mine and alternative ventilation designs investigated. The remaining sections of the paper outline the work involved in each of these main phases of the planning procedure. VENTILATION SURVEYS Conduct of Surveys Two types of measurements were conducted simultaneously throughout the air-carrying routes of the mine: (i) Airflow measurements were made by anemometer traverse or smoke tube at 221 selected stations. Anemometer traverses were repeated at each station until at least three gave results to within 5 per cent. (ii) Pressure drop measurements were made across ventilation doors, regulators and, wherever possible, across stoppings. Additionally, frictional pressure drops were measured along airways where such pressure drops were significant (above 0.01 inches of water gauge or 2.5 Pa over a 100m distance). The trailing hose method was used to determine these frictional pressure drops. This involved laying out 100m of abrasive resistant plastic tubing (3 mm internal diameter) with a 4 ft. pitot-static tube facing into the airflow at either end and a low range pressure gauge connected into the line. The trailing hose method was preferred to the alternative barometer technique for this study because of (a) the relative ease of access between measuring points and (b) the greater accuracy within individual airways. The anemometers used were Davis Biram Type A/2-3" (30 to 5,000 ft/min) and Airflow Developments AM-5000 digital (50 to 5,000 ft/min). The pressure gauges employed were Dwyer magnehelic instruments. These were preferred to liquid in glass manometers because of their portability and dependability under adverse mining conditions. A checklist of the equipment used in the survey is given in Appendix 1. The instruments were calibrated before and after the surveys in the mine ventilation laboratory at the University of California, Berkeley. The survey occupied two teams, each of three men, for ten working days. The work consisted

Jan 1, 1982

By Albert Sauveur

My first paper dealing with the theories of the hardening of steel by rapid cooling was published in the Transactions of this Institute in 1896— 30 years ago-under the title "The Microstructure of Steel and the Current Theories of Hardening," hence, also, the title of the present paper. It was extensively discussed and was, I believe, one of the starting points of many subsequent papers and discussions of the same subject, dis-cusssions which at times became almost violent and which led to the formation of different schools such as the "Carbonists" and the "Allo-tropists." Some of the older members of the Institute, who took part in the debate or who were interested observers, will, I am sure, have kept a vivid remembrance of it. The controversy gradually quieted down, apparently for lack of ammunition, without any side acknowledging defeat. Recently, however, interest in it ha been revived through the claims of some that these vexed questions had at last been solved. In an effort to ascertain if possible the prevailing view of those best qualified to express an opinion a questionnaire was submitted to the following gentlemen: J. 0. Arnold Sir Robert Hadfield Edgar C. Bain W. H. Hatfield Carl Benedicks Samuel L. Hoyt N. Belaiew Kotaro Honda H. M. Boylston Zay Jeffries Harry Brearley H. Le Chatelier G. K. Burgess H. H. Lester William Campbell Francis F. Lucas H. C. H. Carpenter John A. Mathews Pierre Chevenard A. McCance P. Dejean Albert Portevin C. A. Edwards Walter Rosenhain F. Giolliti Bradley Stoughton G. Grenet F. C. Thompson Leon Guillet

Jan 1, 1926

By Thomas Read

AMONG the large number of deep mines in the world there are several which do not differ much in depth. The St. John del Rey mine, in Brazil, has reached a vertical depth of 6726 ft. below the top of its shaft; miners enter it, however, through an adit which intersects the shaft 324 ft. below its top, wherefore it might be said that the mine is really only 6400 ft. deep. In the Kolar gold field of India there are a number of deep shafts, one of which reaches to a vertical depth of 6140 ft. below surface. In South Africa also there are a number of deep shafts, the Village Deep being 6100 ft. early in 1921. The City Deep, Ltd., proposes to sink to a depth of 7000 ft. but pre-sumably by the time it does so the St. John del Rey will be deeper than that, since it has been increasing in depth at an average rate of about 150 ft. per year. The deepest shaft in the United States, the Tamarack No. 5, although it is only 5308 ft. deep, actually approaches nearer to the center of the earth (4100 ft. below sea level, as against 3958 ft. , at St. John del Rey). The deepest workings in the Calumet & Hecla go down to 4600 ft. below sea level. The St. John del Rey is not only the deepest, mine in the world, but it also is worked by the oldest registered English mining company, which was organ-ized in 1830 to work a mine at a considerable dis-tance from this one. That mine proved unprofitable, and in 1837 operations were transferred to the. deposit now under discussion, where operations have been prac-tically continuous ever since.

Jan 6, 1923

By R. A. Anderson, O. D. Sherby, J. E. Dorn

Solid solution alloying increases the plastic properties of aluminum at elevated temperatures by solid solution strengthening, by restraining recovery and recrystallization, and by a Cottrell effect. When binary aluminum alloys are strained and aged at 1940° to 300°K they develop a yield point. This is attributed to a migration of dislocations to solute atoms during aging. IN view of the ever expanding interest in applications of metals and alloys to high temperature service conditions, it becomes increasingly important to be cognizant of the effect of various metallurgical factors on the strength of alloys at elevated temperatures. One problem of wide interest, not only because of its engineering significance but also due to its fundamental scientific importance, is the elucidation of the effect of alloying elements on the plastic properties of homogeneous a solid solutions at elevated temperatures. It is indeed astonishing to note that in spite of its importance, and in spite of extensive random testing of alloys at elevated temperatures, no systematic investigation has been reported yet on the effect of alloying additions on the plastic properties of a solid solutions at elevated temperatures. This deficiency in our knowledge prompted the investigation described in this report. Rather extensive data are currently available on the effect of alloying elements on the plastic properties of a solid solutions at atmospheric and sub-atmospheric temperatures. Such data might be ex- trapolated to higher temperatures and reasonable guesses might be made regarding the influence of such factors as recovery and recrystallization in order to hazard a qualitative estimate of the effect of alloying elements on the plastic properties of a solid solutions at elevated temperatures. Such

Jan 1, 1952

"Coulter's Rainbow and Crooked Falls are situated about five miles below the City of Great Falls. Coulter's, the first of the series in the course of the river, is unimportant and has been submerged by the Rainbow dam. Next below Coulter's is the Rainbow Falls, 47 feet in height. Following Rainbow Falls is the Crooked Falls, 21 feet in height. The power developed at this point is such that the one clam, power house and tail-race utilize the power from all three of the above falls.The development at Rainbow was started October, 1908, and completed July, 1910. It has a total capacity of 21,000 k-w. in generators, and 36,000 h-p. in waterwheels, and operates at 105 foot head. The general scheme of development is typical of what may be called standard practice in the west for plants of medium head, and consists of a low diverting clam, a double pipe line feeding into a balancing reservoir near the plant, and individual pen-stocks supplying the turbines from this reservoir.The dam is a rock-filled crib structure 1,146 feet long and 29 feet high, the up-stream side of which slopes at such an angle that the stability of the clam is assured even under the greatest floods, the weight of the water acting to hold it down, so that the higher the flood the greater the stability. The down-stream side is also sloping and tapers off into a long apron so designed as to take care of any overflow which may occur without shock or commotion. The clam is founded on solid rock throughout its entire length."

Jan 1, 1913

By D. L. Katz, M. J. Rzasa

The derivations of three methods of computing the static pressure gradients in natural gas wells have been presented to show the assumptions made. Charts were developed from which the pressure gradients may be read when the well-head pressure, the well fluid gravity, depth, and the average well temperature are given. A chart for estimating the well fluid gravity from the condensate content and separator gas gravity is included. The effect of the increased average well temperature after flow on the calculation of the static pressure gradient is discussed. Introduction Reservoir pressures have been calculated from well-head pressures for gas wells for many years. As the pressure measurements become more accurate, the need for a reliable calculation of the static pressure gradient often arises. This paper will develop the several methods for computing the pressure gradient in gas wells and make a comparison between them. The method of calculating static pressure gradients in common use is Eq. I (ref. I) or its counterpart which includes a factor for the deviation of the gas from the ideal gas law. P2 - P1 = P1(e0.0000347GX _ I) Eq. [I] in which P1 = pressure at well head, lb. per sq. in. abs. PP = pressure at bottom of well, Ib. per sq. in. abs. G = gas gravity X = depth of well, ft. An alternate method is to compute the average density of the gas in the well and multiply by the well depth in a manner similar to that used for liquid gradients. Derivation of Formulas A static pressure gradient is a special case of the general fluid-flow equation. Consider a pound of fluid flowing in a vertical column from point I to point 2, Fig. I. By an energy balance for fluid flowing from I to 2: U1 + P1V1 + u12/2g + X1 + q = U2 + P2V2+ u22/2g+X2 +W [2] in which U = internal energy, ft-lb. per lb. P = pressure, lb. per sq. ft. V = volume, cu. ft. per lb. u = average linear velocity, ft. per sec. X = height above datum, fl. q = heat absorbed by fluid, ft-Ib. pcr lb. W = work done by system, ft-lb. per lb. An energy balance on the fluid itself gives: U = ?TdS - ?PdV + etc. [3] in which T = temperature, deg- R- S = entropy, ft-lb. per deg. R. per lb.

Jan 1, 1945

By Dean, R. S.

THE numerous theories of hardening which have been advanced in recent years are all satisfactory in accounting for some of the phenomena observed in hardening metals, but none so far presented account for all of the facts observed. Some years ago one of the authors, R. S. Dean,&apos; presented a theory to account for some of the properties accompanying work hardening. The present paper develops this theory further in the light of recent experimental work and extends it to other forms of hardening. Many of the ideas included have come from the writings and personally communicated thoughts of others. We have attempted to give proper credit in every case, but it is possible that we have not always done so. As an historical basis it is desirable here to review very briefly the hardening theories which have been current. The first comprehensive theory of work-hardening phenomena was due to Sir George Beilby.2 He contributed the idea that with cold work part of the structure of the metal was rendered amorphous and that-it was to this amorphous material that the cold-worked metal owed its difference in properties. According to Beilby&apos;s theory this amorphous material was a supercooled liquid and, therefore, had the characteristics of a vitreous material. That such a theory is not capable of explaining the property changes in metals has been repeatedly pointed out. This theory also allowed a slip to take place only once on a given plane, which, as has been pointed out by Jeffries and Archer13 is not consistent with the observed length of an, individual slip and the amount of elongation which can be obtained by wire drawing. The modifications, which have been proposed to this hypothesis to make it coincide with the experimental facts, have to a considerable extent robbed the theory of its clean-cut characteristics. The commonest of these modifications replaces the amorphous phase with an

Jan 1, 1927

By F. L. Bosqui

NO metallurgical process developed in the last half century has been more widely advertised to both technologists and lay- men, or has done more to promote efficiency and economy in the extraction of the valuable portions of ores than has the flotation process. Practically everybody has heard of this strange procedure whereby the heavy portions of an ore are made to float while the light parts sink. Some- times it is called froth flotation, the mineral-bearing froth being from the first a distinguishing characteristic. Many times it is called oil flotation, because a thin film of oil was commonly applied to the particles to be floated to make them adhere to the bubbles that rise through the pulp to form the surface froth. Oil, though commonly used, is not, however, necessary for this purpose, which is one of the facts that has been learned as the process has been developed.

Jan 1, 1940

By Fred C. Bond

IN crushing and grinding the larger particles are more exposed to the work input. They absorb most of the work and protect the smaller neighboring particles from destructive contact with the crushing surfaces or grinding media. The importance of this exposure differential upon the reduction efficiency and product size distribution has long been recognized. Unfortunately, there has heretofore been no direct method of evaluating it, and such indirect methods as observing the slope of the plotted product size distribution line have been used as an indication. In this presentation the Third Theory of Comminution&apos; has been used, together with the exponential formula for size distribution, to evaluate the ex- posure ratio and exposure constant and to illustrate examples of their utility in crushing and grinding applications. The exposure ratio Er varies from zero to unity. It is zero when the product particles are all of one size, and it is unity when the work input has been equally distributed among all particle sizes. It can readily be found from screen analyses plotted according to the Third Theory. The exposure constant K is derived from the reciprocal of the exposure ratio Er. It permits more consistent predictions of size distributions and evaluation of many factors concerned in size reduction operations. The Third Theory1 states that the specific work input required for size reduction is inversely proportional to the square root of the product size less the work required to form the feed. When P represents the diameter in microns which 80 pct of the product passes, F is the size 80 pct of the feed passes, Wi

Jan 1, 1958