Search Documents

By Dean H. Ambrose

This paper presents the results of a study using computer human modeling to examine machine appendage speed. The objective was to determine the impact of roof bolter machine appendage speed on the likelihood of the operator coming in contact with. A contact means two or more objects intersecting or touching each other, e.g., appendage makes contact with the operator?s hand, arm, head or leg. Incident investigation reports do not usually contain enough information to aid in studying this problem and laboratory experiments with human subjects are also not feasible because of safety and ethical issues. As an alternative, researchers developed a computer model approach as the primary means to gather data. By simulating an operator?s random behavior and machine?s appendage velocity, researchers can study potential hazards of tasks where it is not possible to perform experiments with human subjects. Analysis information is helpful to the mining industry in terms of making recommendations that reduce the likelihood that roof-bolter operators experience injury due to contact with a moving boom. Data analysis of roof bolter simulations show that the virtual-operator?s response time has little effect on the number of contacts experienced. Based on frequency and cross-tabulation, regardless of other variables, contact incidents were always greater when the boom was moving up, were always greater on the palm, and were always greater for the boom part of the machine. Also, regardless of boom speed, the 25th-percentile-sized operators experienced more contacts than did other operator sizes. Furthermore, regardless of boom speed, the 152-cm mine seam experienced more contacts than did other seam heights tested. Results of a survival analytic approach suggest that controlling the boom speed is the most important factor in determining the risk of an operator making contact. Based on the data collected, boom speed greater than 41 cm/s results in a substantial increase in risk to the roof bolter operator and should probably be avoided. At speeds less than or equal to 25 cm/s are associated with a more modest relative risk, which represents an acceptable level of risk. Also, at speeds between 25 and 41 cm/s, there could be a particular boom speed in this range at which a significant inflection point in the relative risk estimates occurs. Based on the results, this issue needs to be addressed by future research.

Jan 1, 2003

By W. P. Nel

The introduction of the Higher Education Qualifications Framework (HEQF) and the updated Higher Education Qualifications Sub-Framework (HEQSF) has caused many South African university departments to rethink their programme qualification mixes (PQMs). In addition to the requirements stated in the HEQSF, a number of other factors have to be taken into consideration by a university department. These factors include, for example, the standards generated by the Engineering Standards Generating Body (ESGB) and subsequently approved by the Engineering Council of SA (ECSA) and the need to prepare students for various categories of professional registration with ECSA. This means that a university department has to choose the correct mix of Learning Programmes (LPs) from the HEQSF menu (which consists of 13 types of LPs). Preparing students for ECSA registration is aligned with the mission of universities, which is to teach and undertake research. However, research and the LPs associated with research go beyond the requirements for current ECSA registration. Assuming that universities offering engineering LPs would elect to prepare students for both ECSA registration and teach them to produce research outputs, which is mostly done at Master and Doctorate levels (NQF Levels 9 and 10), then it follows that academics are more interested in NQF Level 5 to 10 pathways (abbreviated as ?L5-10?) rather than the shorter pathways required towards professional registration. (For example, ECSA requires an NQF L5-L7 pathway for registration as a candidate professional technologist. This specific pathway may consist, for example, of two LPs, namely the 360-credit Diploma and the Advanced Diploma.) A L5-L10 pathway is a combination of LPs that will prepare the learner with a NSC (or equivalent qualification at level 4) to Doctoral level (level 10). Universities may choose at least four major pathways from the HEQSF menu in order to educate and develop students from NQF Level 5 to 10. However, various pathways towards registration in the category of candidate with ECSA are also embedded into these four NQF L5-L10 pathways, where each consist of a unique combination of LPs. Each of these pathways has an opportunity cost, and economic reality means that smaller departments may have to choose between the four pathways. Of all the many factors involved in PQM decision-making, the focus of this paper is on the HEQSF requirements, ECSA standards, and ECSA registration and how these, together with the various qualifications and educational LPs provided for by the HEQSF may impact on the PQM decision taken by engineering departments and schools at South African universities. The proposed four NQF L5-L10 ?pathway tool? for PQM decision-making may be useful for pointing out the advantages, disadvantages, and applications of the various pathways and combinations of pathways. Rather than deciding from a menu of thirteen qualifications and associated LPs, this article proposes that decision-making be undertaken on the basis of a menu of four main articulated ?NQF L5-L10? pathways (which also include one or more of the ECSA?s pathways for professional registration). The proposed ?NQF L5-L10 pathway? tool is an attempt to move one step closer to the aim of achieving a structured decision-making approach for designing a PQM at departmental level.

Jan 1, 2014

Comparing Energy Efficiency of Multi-Pass High Pressure Grinding Roll (HPGR) Circuits With increased emphasis on reducing costs and carbon emissions in mineral processing, it is becoming essential to employ the most efficient comminution devices and to use them to maximum effect. High pressure grinding rolls (HPGR) are considered highly efficient compared with other devices, however their relative efficiency in multi-HPGR circuits is less well understood. A series of comminution tests was carried out to evaluate three multi-pass HPGR circuits and a jaw crusher-ball mill circuit. Combinations of HPGR units (1.0 m and 0.25 m diameter), jaw crushers and Bond ball mills were used to grind a 32 mm top size porphyry copper feed (BBWI = 12.1) to a product P80 size of about 150 ¦m. Up to three passes of HPGR were used in each circuit, with energy measurement and size analysis at each point in the comminution process. The energy efficiencies of individual comminution stages and of the overall circuits were quantified and evaluated using three different approaches. The operating work index method for comparing comminution energy efficiency underestimated HPGR performance due to the large amount of fines generated. The -75 ¦m efficiency factor and F50/P50 reduction ratio interpolation methods both give a fairer measure because they better take into account the amount of fines generated by HPGR. The results show that the relative comminution efficiencies of the three multi-pass HPGR circuits tested differ by as much as 22%, providing insights as how to best employ HPGR in a comminution circuit. The most energy efficient of the circuits tested was a three-pass HPGR circuit with a 1.0 m diameter roll on the first pass in closed circuit with an 8 mm screen followed by a second and third pass in a 0.25 m roll.

Sep 13, 2010

By E. H. Izen

A thermal imaging borehole probe was designed and fabricated for the purpose of obtaining thermal images, through smoke, of objects and people in underground mines. The effort was basically unsuccessful; electrical noise, and possibly thermal noise, interferred with the desired signals to the extent that spatial resolution in the images was unacceptable.

Jan 1, 1980

By Jack F. Harang, P. B. Leavenworth

Development during the year 1941 on the Texas Gulf Coast resulted in the dis covery of 27 new fields as compared to 26 fields for the year 1940. Drilling.—During the year, 1405 wells were drilled. Of this number, 1031 were completed as oil wells with 375,000 bbl. daily of new production; 50 were com pleted as gas wells and 324 were failures. The most active area was Jackson County, where 375 wells were drilled and 336 of them accounting for 190,000 bbl. daily of new production. Types of Fields.—Of the 2 7 new fields, 14 are considered to be oil fields, 8 are listed as gas-distillate fields and 5 as gas fields. This may be compared to 26 fields found in 1940, of which 14 were oil fields and 12 gas-distillate fields. Producing Sections.—Frio discoveries retained their predominant position by having 10 Frio fields discovered in comparison to 6 fields in the Wilcox, 4 in the Yegua, 5 in the Miocene and 2 in the Jackson. In the previous year 15 Frio fields were found, 4 in the Wilcox, 2 each in the Yegua, Cook Mountain and Miocene, and I in the Jackson. Production.—Production increased over 1940 approximately 10 per cent, being 113,726,893 bbl. for the year 1941 and 104,127,247 bbl. for 1940. The statistics in Tables I and 2 include distillate and condensate as oil production because no separate reports have been compiled. It is hoped that this separation may be possible some day, but as a great many fields produce both oil and distillate and these arc commingled in pipe lines, separation of statistics will be more difficult than for other areas. New Fields Big Hill, Jefferson County.—Stanolind Oil and Gas Company's No. I George D. Anderson was completed as a gas well from a Frio sand at 8705 to 8720 ft., on Dec. 24, 1941, after having been drilled to a depth of 9500 ft. Additional development is being carried on but it is not possible to evaluate this discovery at this time. Brushy Creek Field, Lavaca County.— Shell Oil Corporation's No. I D. G. McManus was completed as the discovery well in the Brushy Creek field on Oct. 29, 1941, from a Wilcox sand through perforations at 7225 to 7230 ft., making gas and 180 bbl. of 59° gravity distillate. This well was bottomed at 10,998 ft. in the Wilcox. No statement can be made at this time as to the importance of this discovery. Chenango Field, Brazoria County.—J. N. Rayzor et al. completed their No. I Sarah J. Christian through perforations at 8564 to 8572 ft. in a Frio sand, for 453 bbl. of 37.7° gravity oil, on Feb. 6, 1941, after having drilled to 9564 ft. Several wells were drilled in this area during the year but failed to establish important production. This is considered a minor discovery. Clodine Field, Fort Bend County.—Providence Oil Company's No. I Hatfield was the discovery well of the Clodine field, being completed through perforations at 7499 to 7502 ft. for 108 bbl. of 51.2° gravity distillate, on June 19, 1941. The well was bottomed at 8090 ft. Several wells

Jan 1, 1942

By P. B. Leavenworth, Jack F. Harang

Development during the year 1941 on the Texas Gulf Coast resulted in the dis covery of 27 new fields as compared to 26 fields for the year 1940. Drilling.—During the year, 1405 wells were drilled. Of this number, 1031 were completed as oil wells with 375,000 bbl. daily of new production; 50 were com pleted as gas wells and 324 were failures. The most active area was Jackson County, where 375 wells were drilled and 336 of them accounting for 190,000 bbl. daily of new production. Types of Fields.—Of the 2 7 new fields, 14 are considered to be oil fields, 8 are listed as gas-distillate fields and 5 as gas fields. This may be compared to 26 fields found in 1940, of which 14 were oil fields and 12 gas-distillate fields. Producing Sections.—Frio discoveries retained their predominant position by having 10 Frio fields discovered in comparison to 6 fields in the Wilcox, 4 in the Yegua, 5 in the Miocene and 2 in the Jackson. In the previous year 15 Frio fields were found, 4 in the Wilcox, 2 each in the Yegua, Cook Mountain and Miocene, and I in the Jackson. Production.—Production increased over 1940 approximately 10 per cent, being 113,726,893 bbl. for the year 1941 and 104,127,247 bbl. for 1940. The statistics in Tables I and 2 include distillate and condensate as oil production because no separate reports have been compiled. It is hoped that this separation may be possible some day, but as a great many fields produce both oil and distillate and these arc commingled in pipe lines, separation of statistics will be more difficult than for other areas. New Fields Big Hill, Jefferson County.—Stanolind Oil and Gas Company's No. I George D. Anderson was completed as a gas well from a Frio sand at 8705 to 8720 ft., on Dec. 24, 1941, after having been drilled to a depth of 9500 ft. Additional development is being carried on but it is not possible to evaluate this discovery at this time. Brushy Creek Field, Lavaca County.— Shell Oil Corporation's No. I D. G. McManus was completed as the discovery well in the Brushy Creek field on Oct. 29, 1941, from a Wilcox sand through perforations at 7225 to 7230 ft., making gas and 180 bbl. of 59° gravity distillate. This well was bottomed at 10,998 ft. in the Wilcox. No statement can be made at this time as to the importance of this discovery. Chenango Field, Brazoria County.—J. N. Rayzor et al. completed their No. I Sarah J. Christian through perforations at 8564 to 8572 ft. in a Frio sand, for 453 bbl. of 37.7° gravity oil, on Feb. 6, 1941, after having drilled to 9564 ft. Several wells were drilled in this area during the year but failed to establish important production. This is considered a minor discovery. Clodine Field, Fort Bend County.—Providence Oil Company's No. I Hatfield was the discovery well of the Clodine field, being completed through perforations at 7499 to 7502 ft. for 108 bbl. of 51.2° gravity distillate, on June 19, 1941. The well was bottomed at 8090 ft. Several wells

Jan 1, 1942

By Albert L. Toenges, Louis A. Turnbull, EDWARD L. FISH, JOSEPH J. SHIELDS, James J. Dowd

The stripping of coal with mechanical. equipment has progressed since the introduction of the first steam-powered shovel for the retóval of overburden at a mine in Pittsburg, Kans., in 1877...From the smart steam-powered shovels with dippers of less than a cubic yard capacity, small digging radius, and shovels that required manual moving, the trend has been toward large-capacity machines. Steam as power has been replaced largely by electricity, gasoline, and Diesel fuel, and dipper capacity as great as 35 cubic yards has been attained. Shovels and drag lines are self-propelled and revolve through 360°. The cost of these large-capacity modern machines is great, and in order to assure the return of the investment during the life of the property the reserve of coal in the area to be mined must be large;" Many comparatively small areas of coal suitable for strip mining exist, but these areas probably could not be mined, profitably with this large equip- ment. Therefore, heavy equipment has not been used in small areas because of the high cost in place of this equipment, the time and Atpense required to transport the machines to the mine site, and the construction of power lines if the machines are electrical powered.. Scrapers and light excavating equipment ane mobile, and the investment cost is not high. These units have been used in sirring the coal in small areas. A study to determine the methods in, yogue, and economic considerations involved in the use of such equipment was undertaken, and the information obtained is discussed in this report.

Jan 1, 1947

By Felix A. Vogel

Rutile concentrate, used in the manufacture of welding rode, smoke-screen chemicals, and alloys, is being produced by the Titanium Alloy Co. of Arkansas at its mine and. mill in Magnet Cove. The company estimates a substantial reserve of recoverable rutile. This is a new operation, and production figures are not known. Previous operations had stripped the placer material, leaving the underlying mineralized zone. INTRODUCTION This report describes the mining and milling; operations of the Titanium Alloy Co. of Arkansas. The property was examined by the author on March 4, 1942, and subsequent dates. J. A. Wood, general manager, was very helpful in supplying information.

Jan 1, 1944

Resonance re-emission from nickel vapour affords a convenient method for isolating the resonance lines at 3415A, 3515A, and 3524A. The vapour is generated by cathodic sputtering and is illuminated by light from a nickel atomic spectral lamp. The resonance lines thus isolated can be usefully employed for absorption measurements on mineral samples where the nickel concentration is too high for measurements with the more sensitive line at 2320A. A spectrophotometer employing a resonance lamp as monochromator possesses several advantages where a great number of determinations are made under routine conditions. The wavelength setting is stable under even the most rigorous conditions and with the provision for automatic setting of full scale deflection the instrument requires virtually no adjustment. The instrument has been used under routine conditions for the determination of nickel (in the range O· 05-2 per cent) in mineral samples.

Jan 1, 1968

The AMIRA Code of Practice and Guidelines for Metal Accounting was developed in response to demand from a number of sponsor companies, including one major platinum producer. Since its publication in 2007, the Code has become widely accepted in the mining industry world-wide as a guide for best practice in metal accounting. With the changes in the structure of the platinum mining industry in South Africa over the last 10?15 years, in particular, the starting up of a number of small platinum producers who must have their concentrate smelted and the contained valuable metals refined by third parties, the need for metal accounting systems that are accurate and have an acceptable level of precision has become even more critical to the success of a platinum-producing operation. The current state of metal accounting in the industry is discussed, and possible areas for improved accounting and associated metallurgical efficiencies are identified.

Jan 1, 2013

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and. the results are described in this report.

Jan 1, 1983

By M. Vallée

"RÉSUMÉDurant les 10 dernières années, les améliorations dans le contrôle des limites des sautages et les arpentages après l’exploitation ont fourni des informations préalables et post facto sur les limites minières réalisées par rapport à la planification, plus particulièrement pour les grands chantiers exploités par les méthodes chambres vides et sous-niveaux. Cependant, peu de recherches ont été faites pour améliorer la délimitation du minerai, l’estimation des ressources et des réserves, les études de faisabilité et la récupération minière dans d’autres types de gisements. Il faudra d’abord expliciter les impacts des lacunes, en quantité et en qualité, de l’information géologique et de l’échantillonnage sur le rendement de l’extraction. Il faudra également remplacer la notion de « dilution générale » par celles de « dilution » et de « perte de minerai ». Les impacts des lacunes observées sur l’exploitation des gisements d’or filoniens sont démontrés par une simulation basée sur des résultats d’études antérieures à la mine Thompson d’Inco, des impacts financiers de densités d’information moindre et par des analyses des valeurs actualisées nettes (VAN) de deux cas types.Deux gisements similaires, de 3 m et 6 m de largeur et exploités par chambres vides sont étudiés, en prenant pour cas de base la délimitation sur maille de 7,5 m (25 pi.) et en étudiant les impacts des limites moins précises supportées par une maille de 15 m (50 pi.), en assumant que ces imprécisions moyennes de +/- 0,62 m se transforment soit en surestimation (dilution), soit en sous-estimation (pertes de minerai).Les impacts d’information moins précise ont été beaucoup plus forts sur le gisement plus étroit : autant la dilution que les pertes de métal ont diminué les VAN du gisement de 3 m de 39,27 % et 45,41 % respectivement, tandis que les VAN du gisement de 6 m ont été diminuées que de 12,84 % et 11,55 %.Ces impacts des valeurs actualisées nettes diminuées justifient et exigent des efforts plus systématiques pour s’assurer que les travaux de mise en valeur et les études de faisabilité soient réalisés de façon requise pour optimiser l’exploitation et offrir aux investisseurs des rendements compétitifs par rapport à ceux des autres secteurs industriels. ABSTRACTDuring the past 10 years, research work to improve the survey of stope limits after mining supplied useful information, particularly for large open and sub-level stopes, regarding waste dilution caused by differences between final production limits and planned stope limits.However, the efficiency of this information to improve the overall efficiency of the mining process is limited, given that the impacts of inaccurate ore limits leading to dilution (sensu stricto) and ore losses have not been considered adequately. Geological/sampling information should be optimized in terms of quantity and/or quality for the deposit characteristics and the constraints of the mining method used. As industry practice regarding the definition and recording of dilution is flexible and as ore losses frequently are poorly documented, the use of these terms is reviewed.Simulations were carried out on two typical narrow gold deposits, based on an earlier study at Inco’s Thompson mine regarding the impacts of wide to narrow delineation grids using recorded variations of vein geometry. Vertical to sub-vertical deposits of 3 m and 6 m widths mined by long-hole open stopes were considered. Deposits delineated by 7.5 m (25 ft) grids were taken as a base case and the impacts of less accurate limits in conjunction with long hole mining based only on a 15 m (50 ft) delineation grid. The impacts of overestimation (dilution) and underestimation (metal losses) were considered separately, using the average error of +/-0.62 m recorded in the Inco study.The impact of less accurate information was much stronger on the narrower deposit: both dilution and ore losses diminished the net present value of the 3 m wide deposit"

Jan 1, 2005

By James Gibbs

In order to provide an initial approach to the deposits of oil shale, nahcolite, and dawsonite in the central area of the Piceance Creek Basin in northwestern Colorado, the U.S.B.M. and associated contractor personnel drilled and cased a 96-inch ID shaft to a depth of 2,371 feet. The shaft was constructed using "big hole" drilling techniques and succeeded in giving access to previously inaccessible deposits of the above minerals. This report documents the construction from its beginning in January 1977 to its completion in January 1978. Procedures used and problems encountered are discussed in derail.

Jan 1, 1978

By E. A. Lowe, A. F. Bellamy, J. W. Smith

"In the autumn of 1977 Bethlehem management initiated feasibility studies on recovery of by-product molybdenum from concentrate produced at the existing Highland Valley mining operation. Over the fall and winter months test work was carried forward concurrent with design, flowsheet, equipment specification and cost studies. The decision was made to go ahead with a 200 ton-per-day treatment plant. Construction started in early 1978 and progressed to an initial start-up stage in mid-June. Full operational status was reached in August 1978. Operational results through August 1979 are presented. INTRODUCTIONBethlehem Copper Corporation operates a 20,000 ton-per-day Open Pit Mine and Flotation Plant located in the Highland Valley, some 30 air miles Southwest of Kamloops and 20 miles Southeast of Ashcroft, B.C.Two open pits are worked; the Iona Pit with limited reserves of higher Mo content, and the lower grade, more extensive Jersey Pit. Upwards of 150 tons per day of bornite-chalcopyrite bulk concentrate is produced, ranging 0.25% to 1.5% in molybdenum grade depending on the area mined."

Jan 1, 1980

By Alan A. Campoli

The mining industry has long been searching for an effective structural application that prevents weathering and falls of loose rock, debris, and sediment. J-Crete is a fiber-reinforced, engineered, cementitious composite rock application that is designed, tested, and successfully utilized as such a material. Laboratory evaluation of J-Crete material properties has shown the final compressive strength to be in excess of 7,300 psi (50.34 MPa), with 24 hour strength in excess of 1,500 psi (10.34 MPa). The flexural tensile strength is in excess of 600 psi (4.1 MPa) and is provided through a unique combination of polyvinyl alcohol (PVA) fibers activated by a proprietary liquid additive that prevents them from clumping and enables even distribution throughout the grout. Tensile bond strength in excess of 350 psi (2.4 MPa) at 28 day cure tightens the strata and holds loose material in place. Practically impervious to gas and liquids, J-Crete protects strata against long-term weathering, does not require screening to be effective, and has proven to be a successful waterproofing material. J-Crete has demonstrated the potential to alleviate coal mine roof cutters in soft, wet clay formations. J-Crete reinforces coal mine ribs by bonding directly to the rib, conforms to the strata, strengthens the rib, and eliminates sloughing due to long-term weathering; stabilizes coal mine entries by bonding directly to the brow and roof, and creates a monolithic shell with double reinforced corners.

Jan 1, 2012

By Joe Roby

Rolling disc cutters are the business end of hard rock and mixed face tunnel boring machines (TBMs). Since their first successful employment on a TBM over fifty years ago, disc cutter technology has constantly evolved, allowing modern TBMs to excavate very hard and abrasive rock efficiently. Disc cutters have also been employed successfully on earth pressure balance (EPB) and slurry machines, cutting rock under water and ground pressure. The range of materials excavated by machines today is broader, excavation rates higher and cutter costs lower than ever before, proving the value of investment in cutter development. This paper describes recent improvements in disc cutter components including cutter ring materials and processing, as well as improvements in lubricants, bearings, seals and cutter condition monitoring. These developments have resulted in more reliable cutters capable of operating in a wide range of geological conditions. Ultimately these improvements result in a better value for both contractors and project owners.

Jan 1, 2008

By Shular R. Scudamore

There was a time when heavy-duty apron feeders were built to last almost forever. The machines were heavy and built to maintain certain expected longevity and reliability. Increasing emphasis on return on capital leads to cost-effective designs. Costs can be increased or decreased, depending on customer specifications and the design philosophy of the feeder manufacturer. Specifiers can make important contributions to cost effectiveness. To do so, this article describes what should be known about planning with a supplier for heavy-duty apron feeders. There are several factors that should be considered, including capacity, characteristics of material carried, length, method of feeder loading, degree of lift, hopper opening, pan construction, and type of drive. Today's apron feeders are built in various sizes and with a variety of components to handle heavy, lumpy, or abrasive materials that can ruin lighter feeders. Careful feeder selection is important if it is to provide a controlled feed rate, absorb huge impacts, be used with long hopper openings, and have a relatively low power-perton capacity. Variations in systems and materials demand that each feeder be designed for its application, drawing on a wide range of components. Therefore, certain factors must be considered before final specifications are drawn. Capacity The design and application of an apron feeder is based on how material passes through a given system over the feeder into processing machinery. The processing machinery's capacity governs other equipment and productivity of the flow. From this basic information, related sizes of upstream equipment can be determined. Of these, the apron feeder acts as the "mouth and neck of the bottle." No more will pass than the mouth and neck will accommodate. Everything in the apron feeder design, from dimensions to power, is based on processing machinery. Material Considerations Are Vital Just as the nature of materials to be crushed or screened affects capacity and productivity of a crusher or a grinding mill, so does it affect capacity and performance of a feeder. Lump size must be identified closely so the pan width can be selected to accommodate the maximum lump with room to spare. For example, a lump size of 760 mm (30 in.) indicates a pan width of 1.5 m (60 in.) While two times the maximum lump is considered minimum width, if the maximum lump

Jan 12, 1983

Recovery of Vanadium from Stone Coal Through an Environmentally Friendly Acid Leaching Technology

Sep 13, 2010

By Keli Vanessa Salvador Damin

Este trabalho apresenta uma nova abordagem sobre o emprego sequencial dos tratamentos termoquímicos de superfície utilizando a tecnologia de plasma. No trabalho são avaliados tratamentos de superfície, individuais e sequenciais, de nitretação/cementação. Os tratamentos foram realizados no campo ferrítico com o objetivo de manter as tolerâncias dimensionais. Amostras de aços AISI 1005 foram tratadas em descarga luminescente anormal sendo realizados ciclos únicos de cementação e nitretação e também ciclos conjuntos de nitretação + cementação. Todos os tratamentos foram realizados a 500°C com um tempo de patamar de 3 horas para cada tratamento. A composição da mistura gasosa variou de acordo com o tratamento: nitretação - 5%N2 + 95%H2 ou 3%N2 + 97%H2; cementação - 5%CH4 + 95%H2. A caracterização microestrutural das amostras foi realizada por microscopia óptica e MEV além de difração de raios-X. Análises de microdureza também foram realizadas. As analises de raios-X mostraram que ocorre a estabilização de uma camada de cementita nos tratamentos de cementação. Nas amostras nitretadas em atmosfera contendo 5% de N2 foi observada a presença de camada de compostos. Já em atmosferas contendo 3% de N2 não houve a formação da camada de compostos. A maior profundidade de endurecimento foi obtida para a amostra nitretada + cementada.

Aug 16, 2017

By B. J. Vorster

Introduction The South African Iron and Steel Co. Ltd., in Sishen, operates a large iron ore mine in the Cape Province of the Republic of South Africa. The mine is about 600 km (370 miles) west of Johannesburg. Its annual capacity is 100 Mt (110 million st) of ore and waste. Present production is 60 Mt/a (66 million stpy). The mine operates continuously six days a week. Primary equipment includes 55 154 t (170 st) Wabco and Unit Rig trucks and 14 P&H shovels. During 1979, a feasibility study into the application of a trolley assist system was launched. This was due to the escalation in diesel fuel costs and the appeal by the South African government to reduce the use of fossil fuels. Tests and economic evaluations proved the system technically feasible. The estimated discounted cash flow return exceeded 50%. Diesel fuel consumption would be reduced by 120 ML (31.7 million gal) in the next 10 years. The construction of 7.7 km (4.8 miles) of line and the conversion of 66 154 t (170 st) trucks were completed in March 1982. System description The conventional 154 t (170 st) diesel electric rear-dump haul-truck is equipped with two direct current wheelmotors in the rear axle. They drive the rear wheels through planetary gearboxes. A 1.2-MV (1600-hp) diesel engine and an alternator is used to power the wheelmotors. The trolley assist system consists of an overhead power line, a current collector mounted on the truck, and add-on control equipment where external electric power is routed by way of the current collector to the motorized wheels. The diesel engine is used to propel the truck on level sections. On inclines, the wheel-motors of the truck are coupled by way of a current collector to the externally generated electrical power supply for propulsion. The diesel engine, having lower output than the wheelmotors, limits the truck performance. Previously, maximum output was required from an engine on inclines. By supplying the wheelmotors from a virtually unlimited outside electric energy source, the truck performance is enhanced to the extent that speed is increased by 46% and fuel consumption reduced by 75%. System design The unique operational requirements of this mine rendered the already proven trolley pole system useless. Minimum loss in truck mobility and flexibility was required. Overhead lines and substations were required to be relatively light and portable. This enables fast repositioning of a line with no loss in material. These unique specifications set the base for the design of the Sishen system. Steel I-beams, 203 x 203 mm x 52 kg/m (8 x 8 in. x 35 lb per ft) with lengths varying from 8.3 to 11.3 m (27 to 37 ft), mounted on base plates about 4 x 2.6 m (13 x 8.6 ft) were used as masts. The masts were erected at about 50 m (165 ft) and the base plates covered with about 12 t (13 st) of iron ore to keep them absolutely stable. Results from the pilot installations indicated that using single cantilever cross arms for insulator and overhead conductor suspension was not practical. The tension in the overhead varied too much with temperature changes, causing too much sag in the lines. There had to be a positive and negative conductor. It was decided to suspend each polarity on an independent cantilever and keep the conductors under constant tension by weights acting through a two-to-one pulley tensioning arrangement. For each overhead conductor, a standard 160-mm (6.5-sq in.) grooved copper railway conductor was used. To obtain the necessary current carrying capacity, two of these conductors are used in parallel per pole. Insulators are rated at 4 kV and are of the composite type. An 11-kV three-phase line, supported by the pantograph line masts on the opposite side of the dc line, feeds the rectifier stations. The rectifier stations consist of an 11-kV to 860-V, three-phase 1.46 MVA transformer and a three-phase diode bridge rectifier. The output voltage is 1200 V do earthed through a current limiting resistance network so that the line po-

Jan 4, 1986