Search Documents

The efficiency of water sprays in suppressing airborne colliery dust depends on many variable factors. A survey of previous work in this field shows that swirl spray nozzles are the best dust suppressors.Investigations carried out in an experimental dust chamber show that, in spite of limitations to the application of water sprays in underground use, promising dust suppression efficiencies in mechanised mining can be obtained with swirl spray nozzles.INTRODUCTIONA dust hazard has always been associated with coal mining, and the recent growth of mechanisation has resulted in a greater production of fine coal and dust, thus increasing the hazard. A better knowledge and appreciation of the medical aspects and dust explosion factors has led to practices reducing the seriousness of the problem. However, the dust hazard still exists and its control is basically an engineering problem.Dust, as with any atmospheric pollution, may be removed from the, mine by ventilation, which is an indirect method of control. Direct methods, in which the dust is prevented from being produced and from becoming airborne, should be employed where possible. Of these direct methods the most significant is the use of water sprays.THE DUST HAZARDAn appreciation of the physical nature of the more important dust hazards is necessary before considering the removal of the hazard. The main hazards associated with colliery dusts are the health hazard and the explosion hazard. "Dust" comprises solid particles of size minus 20 mesh Tyler (833 microns).

Jan 1, 1964

Following a short review of selected literature, a back analysis of stress measurements of stress regeneration in a closed mini-longwall is shown. The agreement is good, lending confidence to the parameters used in the proposed numerical model. Foundation yielding was modelled in the absence of total stope closure. A ?Prandtl? wedge was formed, coinciding with the yield point of the pillar/foundation system. Some theoretical work is used as a starting point for the formulation of a new design methodology for strike or dip stabilizing pillar/foundation systems in deep level goldmines. The existing guideline for the stability of foundations (APS< 2.5UCS) is critically examined. Finally, the advantages of the new approach, and the work required to substantiate the proposed new design methodology, are outlined.

Jan 1, 1998

By P. Mbele

Iron ore concentrate is not easily transported to, or processed in, ironmaking plants, therefore it is necessary to agglomerate. This paper will determine the possibility of agglomerating Sishen concentrate into suitable ironmaking feedstock. Pelletizing is one of the conventional and preferred agglomeration processes for iron ore concentrate investigated at Kumba Value-In-Use Laboratories. Sishen concentrate was mixed with binder, and then pelletized using a laboratory pelletizing disc; afterwards the green pellets were indurated at high temperatures to give strength high enough to survive handling and lessen disintegration in the shaft during ironmaking. Sishen pellets have satisfactory physical and metallurgical properties which make them suitable feedstock for the direct reduction processes. These were tested under Midrex shaft operational conditions and performed well, with a metallization of 94.47% being attained.

Jan 1, 2012

By G. R. Fitterer, E. A. Krockenberger, B. E. Sockman, R. B. Meneilly, J. F. Eckel, E. W. Marshall

"Steel manufacturers have noticed a decided tendency on the part of many of their customers to become more exacting in their steel specifications. Under these conditions, the steel must not only meet the specifications of physical properties (tensile strength, reduction of area, elongation, impact strength, grain size, normality, etc.) and the chemical analyses, but must also pass the inspection test of ""cleanliness.""By cleanliness is commonly meant the absence of oxide and sulphide inclusions. Other foreign particles such as furnace or ladle slag, ladle and runner brick, etc., must also be absent. The determination of cleanliness at present is usually made by microscopic inspection or macroetching.The rejection of steel for lack of cleanliness is increasing, out cleanliness is one of the most difficult requirements for the manufacturer to fill. The reason for this is that every steel inspector has a different conception of a. clean steel. A material which does not pass the examination of one inspector way be regarded as entirely satisfactory by the metallurgist of an¬other company. The cause of this confusion and disagreement concerning the definition of a clean or a dirty steel is simply that as yet no standardized procedure for the determination of impurities has been proposed and generally accepted, since many variables are encountered which interfere with the development of a satisfactory method. An idea of the complexity of this situation will be obtained from the following pages.A Survey of Proposed Analytical MethodsAlthough no analytical method has been accepted, many procedures have been proposed, as may be seen in Table 1. Therein are listed 16 of the better-known processes, pith references to the work of their originators, their mechanisms of determination, and their applicabilities. Among these is included the electrolytic method developed by one of the present authors, and some comparison between this and previously proposed procedures may be obtained by a study of the table. It appears that this new method Las many advantages over the others, and this paper presents a critical Study of its value."

May 1, 1933

By I M. Platten, Y Xie

Complex gold deposits are generally characterised by variable geometries, strong structural controls on grade distribution and a high-nugget effect. The use of diamond drilling and fire assays in this environment often results in an understatement of grade. Bulk samples are likely to be the closest estimators of true grade, and may be required to evaluate geological/grade risk during resource estimation/feasibility studies. Any bulk sampling program requires appropriate planning and implementation. The planning stage should attempt to delimit the extent and nature of mineralisation; characterise mineralogy and metallurgical properties of the ore; and define bulk sample size and how it will be sampled/processed. The approach to sample processing will be governed by the results of metallurgical testing and geological knowledge. Careful design of sampling protocols must be undertaken through material characterisation, understanding of gold particle sizing and the application of GyÆs Sampling Theory.

Jan 1, 2008

By W. R. Byrnes

This project was initiated on October 1, 1980 and will be completed on December 31, 1983. The project was Initially approved and funded by the Office of Surface Mining and subsequently was moved to the jurisdiction of the Bureau of Mines. It was administered through the Indiana Mining and Mineral Resources Research Institute. The research was done to assess reforestation success and ultimate productivity for areas reclaimed under the Surface Mining Control and Reclamation Act of 1977 (P.L. 95-87). The Permanent Regulatory Program for implementation of P.L. 95-87 Includes provisions for revegetation that require seeding of ground cover plants to control erosion until permanent vegetation such as tree species Is established, and restoration of mined land to its original or better productivity. Much of the land to be surface-mined presently supports forest cover and it is anticipated that reconstructed minesoils will exhibit high productive potential for hardwood tree species. Hence, information was needed on compatibility of ground cover and tree seedlings when established concurrently as well as on revegetation success under postmining versus premining conditions.

Jan 1, 1983

By Vu Van Dong

Resource estimation is the science of determining the amount and quality of a given material in the ground that has the potential to be mined at a profit. This is because during this time computers have become more widely available and more powerful and software packages have become more comprehensive and user friendly. Over the past three years The Mining Geology Company with the support from Vinacomin Group has developed the Coal Geological Modelling and Reserve Estimation ? VMG system. The VMG system enables the geological and mining engineer to start at the reserve estimation for the mine design and planning. The VMG system enables the national and international standards (NI43-101, CIM-Canada; SAMREC Code, Africa, and JORC Code, Australia) and user friendly with menu driven thereby permitting the engineer with minimal computer training to rapidly learn and utilize the system. Geological and mining data input through digitized map files and drill-holes information files stored in the database that is an integral part of the VMG system with the main function for collection, validation, and recording, storing and processing of data will include both ?primary? (observation and measurement) and ?interpreted? data. It is recommend that data be stored digitally, using a documented, standard format and a reliable storage medium that allows for easy and complete retrieval of the data. The coal reserve estimation through standard polygon methods with the increased use of these mathematical techniques (geometrical modelling, geostatistical method, least square method, ?) over the last ten years corresponds, to some degree, to a decrease in both the amount of the coal deposit mapping and, in particular, coal seam structural interpretation and modelling, and permit rapidly evaluation of coal seam and overburden quality and quantity. The understanding of the relationship between the coal mineralization of interest and the likely related complicate geological processes and structure that govern its emplacement and geometry within the geological framework is essential to the establishment of the geological controls for coal mineralization. System outputs includes: drillholes summary reports, stratigraphy, cross-sections, isopach maps, structure, contour maps, premining and post mining topography maps, and 3D perspective view on coal seam structure.

Oct 1, 2009

THE object of the present paper is to give a brief description of the metallurgical process followed by the Grand Junction Co, and the results obtained therefrom. All figures quoted are from the actual working of the plant over a period of six months from January to June, 1910. The short ton of 2000 lb. is used by the company. Its gold is valued at 84s. per oz. fine, silver at 2s. per oz. fine. The ore consists essentially of a gangue of quartz and calcite, with 8 to 10%sulphide-pyrite, sphalerite, galena, chalcopyrite, and traces of arsenic and antimony. The colmtry-rock is a highlyaltered dacite. Small stringers of highly-mineralized ore penetrate the footwall of some of the lodes, forming a valuable stockwerk up to 3 ft. in thickness. In stoping, this is mined with the well defined lode, thus bringing into the mill at times a considerable quantity of hard country-rock. The gold exists in an exceedingly fine state of division, consequently rendering it necessary to grind very fine to obtain a satisfactory extraction.

Jan 1, 1912

By Stephen H. Chung

The SABREX computer blast simulation program permits the study of the effective use of explosive energies and predicts the total performance of a blast in terms of:fragment size distribution: muckpile profile; breakage at grade, column and collar with respect to the control case; crack penetration; damage envelope behind and beneath blastholes; a complete cost analysis including explosives, drilling and accessory costs

Jan 1, 1995

In the Broken Hill South mine tile practice of issuing to the miner a quantity of fuse and a box of caps from which he made up the &quot;rods&quot; required for a particular blast, has been abandoned. Instead, capping stations have been established, and the miner can now obtain, from the magazines, fuses cut to accurate lengths with the detonators attached.Various types of fuse-cutting machines and crimping devices are available, but only those used by the Broken Hill South Mine Ltd. are described in this paper.The fuse-cutting machine, designed by the engineering staff, is an electrically driven unit fitted with a gear box for the purpose of adjusting the rate at which the fuse is fed to the cutting device, thereby enabling fuses of various lengths to be accurately severed from the main coil of fuse.The machine in question is designed to cut 4, 6, and 8-ft. fuses, but no difficulty should be experienced in designing a machine to cut fuses to any required lengths.

Jan 1, 1932

The Canada Centre for Remote Sensing (CCRS) has developed an airborne sensor, the SWIR Full Spectrum Imager (SFSI) which detects in the short wave infrared range of the solar spectrum from 1220 to 2420 nm. In June of 1995, a demonstration flight was undertaken in the state of Nevada with the support of the companies listed above. The focus of the flight was to collect image data over well known mineral deposits with the objective of evaluating the applicability of this sensor to alteration mineral mapping. Some of the Nevada sites chosen include Cuprite and Goldfield, volcanic hosted acid sulfate systems; Yerington, a structurally complex porphyry copper deposit; and Virginia City, a quartz-sericite-pyrite vein system with advanced argillic pods. Ground spectral data was collected with the PIMA-II spectrometer. Solar reflectance calibration was done by Desert Research Institute personnel at Virginia City and Cuprite. This paper will discuss the configuration of the sensor and present image and ground data for Goldfield and Virginia City.

Jan 1, 1995

By R. J. C. MacDonald

"The first recorded discovery of placer gold in Canada was on the Chaudiere River in Quebec's eastern townships in 1832 and the first major production came from placer deposits in British Columbia in 1858 (Verity 1974). Placer deposits were the major source of gold until the late 1890's, although lode deposits were found in Nova Scotia in 1862. In 1896 the Klondike Gold Rush commenced with the discovery of gold by Henderson and Carmack in the Yukon. The peak was reached in 1900 when over one million ounces of gold valued at approximately $22.3 million were recovered. With the exhaustion of the easily accessible deposits, more capital intensive operations were necessary such as those initiated in 1906 by the Yukon Gold Corporation. This giant dredging operation continued to produce until 1966. Today only a few small operations remain.The development of Canadian lode gold mining began in earnest around 1900 when the railroads were opening up the interior and western part of the country. At this time many discoveries occurred, particularly where mineral outcroppings were near surface. Tremendous impetus for exploration and the reopening of former producers followed the elimination of the gold standard by Great Britain around 1931, and more importantly the United States in 1933, with subsequent stabilization of the price of gold at $35 per ounce in 1934. Prior to this the price of gold was basically unchanged since 1717, approximately, $20 per ounce (Verity, 1974; Green, 1973).The depression of the 1930s adversely affected most industries, however for the gold producers it was a very profitable time. Prices of materials and equipment declined and labour was cheap and plentiful. Interest in gold mining was further stimulated in 1936 when a three year tax exemption was declared for all new metal mines. In 1938 a decline in the value of the Canadian dollar relative to the U.S. dollar benefitted the industry. The second world war provided yet again further incentive for gold production and in 1941 Canadian gold production reached a high of approximately 5.4 million ounces. This figure was not surpassed until 1991 when approximately 5.6 million ounces were produced (Natural Resources Canada, 1996 )."

Jan 1, 1998

By Christopher Bambridge

The Washington State Department of Transportation (WSDOT) is constructing a new tunneled route under Seattle to replace the existing State Route 99, Alaskan Way Viaduct (AWV), which follows the historic waterfront for several miles. The viaduct separates the businesses that rely upon the tourist trade from the down-town area. The reconnection of the city to the waterfront areas will occur following the completion of the SR99 Re-placement program that replaces the aging structure that was severely impacted by the 2001 Nisqually earthquake, with a state-of-the-art, twin-deck highway with a world record-breaking 17.4-m (57.3-ft) bored tunnel. Constructed in the 1950s, the double-tiered viaduct is nearly 3.2 km (2 miles) long and runs parallel to city?s waterfront. The viaduct, which is partially supported by the seawall, is a vital local and regional transportation link and carries about 110,000 vehicles each day. The seawall, built from concrete and timber in the 1930s, extends along Seattle?s waterfront and supports the soil behind it. Studies in the 1990s showed that the viaduct was nearing the end of its useful life, apparent by its exposed rebar and weakened columns. The 2001 Nisqually earth-quake further damaged the viaduct, forcing WSDOT to temporarily close it for inspection and limited repairs. The viaduct and nearby seawall are vulnerable to an-other earthquake and continue to show signs of age and deterioration. Following a collaborative process, WSDOT developed the following guiding principles to the viaduct replace-ment:

Sep 1, 2013

THE choice of a pumping plant for the drainage of a mine is a matter of such importance that it is obvious that in a short paper it is impossible to go fully into the reasons governing the adoption of any particular type. The author, therefore, proposes to briefly discuss the methods.in vogue, and, as far as possible, to point out the advantages and disadvantages of the numerous systems. The probiem is of extreme importance to the mining engineer, and it appears that in the past sufficient thought has not been given to this branch, as shown by the numerous failures which are encountered.When water is met with in large quantities, the development of the mine depends upon the pumping plant to such a great extent that the most careful consideration should be given before deciding on any particular scheme for drainage. The pumpingplant in a mine should be looked. upon in the light of an insurance policy, and should be treated as such, care being taken that the premium is as low as possibl~, and to ensure this it is necessary that the most efficient plant be secured. Local conditions play such an important part ill the design of a plant that no hard and fast rules can be laid down. When the amount of water to be handled is small, and there is no possibility of any increase...

Jan 1, 1912

Provide improved permanent stoppings designed specifically for use in mines with large cross-sectional entries. Approach The large entry sizes in many mines, such as oil shale, salt, and limestone, make the conventional stopping construction techniques used in smaller opening mines unacceptable. The Bureau of Mines and Colorado Mining Association jointly sponsored a contract to design and test new or modified stopping concepts for these mines. The most promising concepts were then tested in an oil-shale mine having 30-foot-high by 55-foot-wide mine entry openings. All stopping designs tested were evaluated in terms of cost, air tightness, and resistance to blast damage.

Jan 1, 1987

By E. G. Davis

As a result of interest by the U.S. Department of Energy, the Bureau of Mines conducted studies on comminution of bituminous coal to the 2-um particle size range using the Bureau-developed turbomill. Both "plant grind" size (80 pct minus 75 um) and microsize (minus 10 um) coal can be produced in a single step with the Bureau&apos;s turbomill. In 15 min, minus 2.4-mm coal milled in water with steel shot was reduced tc 65 pct minus 75 m and 26 pct minus 2 m, with an energy requirement of 139 kW^h/mt coal. Plant-grind size coal milled in water, with Ottawa sand as the milling medium, was reduced to more than 45 pct minus 2 m in 15 min, at 175 kW?h/mt. Plant-grind coal milled with steel shot was reduced to 57 pct minus 2 um in 15 min, at 138 kW?h/mt. When diesel fuel was substituted for water, the milling of the coal was less effective and less energy efficient. Keeping the pulp dispersed was critical. Without an effective dispersant, the slurry became very viscous with increased milling time, resulting in higher energy requirements, low heat dissipation, and poor grinding efficiency.

Jan 1, 1987

By N. E. Mkadmi

Backfilling increases the stability of underground stopes and may help reduce the environmental footprint from the mining operation. The barricades holding the backfill in place must be designed to prevent failure based on the total and effective stress states, which depend on fill properties, stope geometry, and filling rate. This paper presents results from a numerical study aimed at analyzing the stress states associated with the response of paste backfill following stope filling, with an emphasis on the short term behavior. The simulations illustrate how stresses evolve with backfill drainage and filling rate in a vertical stope.

May 1, 2011

The minerals industry consumes billions of dollars in raw materials, equipment, tools, services and chemicals. The industry, though, has turned overmuch of the research and development (R&D) for these products to manufacturers and suppliers. Now the industry and its suppliers must decide how much R&D the mining industry should be responsible for and what role the suppliers should play. Promoting R&D As a result of the current environment in the mining and minerals industry, there has been a substantial decrease in R&D. Depressed prices, stagnant growth, cost cutting and rationalization are evident.

Jan 1, 2000

A poured slag bottom is universally considered to be the best type bottom for copper reverberatory furnaces. It is impervious to molten matte and ready for immediate use.When molten slag is not available a monolithic silica bottom is the second best; such a bottom has been adopted at Mount Morgan. The laying of such a bottom is a phase of smelter construction on which so little real information is obtainable that a day to day record of such a recent example as Mt. Morgan&apos;s 19 ft. x 40 ft. reverberatory may be of interest. The work was done under the direction of E. Pesout, of McGill Smelter, Nevada. PREPARATION OF THE BOTTOMA 26-inch bed of closely packed firebrick with sand-filled joints was first laid on the clean, dry concrete foundation and the whole dried out by small fires maintained on the brickwork for several days. Ninety tons of silica sand was meantime thoroughly dried and stored in clean drums. This sand must be low in FeO and CaO and contain about 95% Si02 , the majority of which should be present as tridymite. This form of silica shows little expansion at high temperatures, for it is the form stable between 870&#176; and 1470&#176; C.Its presence thus minimises disturbance to the bottom by the expansion which, during the burning in, would mark the transformation of quartz to tridymite.

Jan 1, 1939

This paper presents the results of a unique study conducted by the National Institute for Occupational Safety and Health (NIOSH) from 2016 to 2019 to evaluate the effects of longwall-induced subsurface deformations on shale gas well casing integrity and underground miner safety and health. At both deep and shallow cover instrumentation sites, surface subsidence measurements, subsurface in-place inclinometer measurements, and underground pillar pressure measurements were conducted as longwall panels were mined. Comparisons of the deep and shallow cover test site results with those from a similar study under medium cover reveal an interesting longwall-induced response scenario. Under shallow and medium covers, measured horizontal displacements within the abutment pillar are one order of magnitude higher than those measured under deep cover. Conversely, measured vertical compressions under deep cover are one order of magnitude higher than those under shallow and medium covers. However, FLAC3D simulations of the casings indicate that, in all three cases, the P-110 production casings remain intact under longwall-induced deformations and compressions, which has serious implications for future mine design in areas where shale gas wells have been drilled ahead of mining.

Jan 7, 2020