Search Documents

By Shaolong Chen

Feeding dry sulfide concentrate into smelting furnaces enhances process performance and reduces the energy consumption and exhaust gas flow. Direct heated rotary dryers and flash dryers have being replaced by rotary steam dryers featured by very low wear rate of the pipe heating elements and long maintenance interval. Impact of the drying processes on the environment receives more and more attention as the emission legislation tightens. In this regard, environmental factors such as SO2, CO2, dust and gas flow among rotary dryers, flash dryers and steam dryers were compared. Selection of a rotary steam dryer for copper and nickel concentrate drying would be an ideal solution to reduce the pollution of exhaust gas, as drying is achieved by indirect contact to the steam at relatively low drying temperature and as the off-gas contains almost only water vapor and air. The emissions can be significantly reduced and only small and simple off-gas handling units are needed.

Jan 1, 2006

By Matti Leiponen

During the last few years Outokumpu Oy has put forth efforts to develop the material handling in the Pori tankhouse. The final objective is full automation including cell loading. The fully automated material handling provides high quality anodes and cathodes as well as equipment and handling systems capable of very accurate cell loading. The new machines and equipment for accurate cell loading and the methods to produce high quality anodes and starting sheets are described in this paper.

Jan 1, 1987

By N. R. Green, N. J. Humphreys, D. McBride, T. N. Croft, M. Cross, D. M. Shevchenko

"Centrifugal casting offers a route to high quality products in difficult to cast high temperature low superheat alloys and thin section molds. Under centrifugal forces metal is forced into thin sections and can fill thicknesses of less than a millimeter. However, due to the high liquid metal velocities there is a high risk of surface turbulent flow and air entrainment within the liquid metal. The combination of interacting flow-thermal-solidification phenomena and associated defects is a challenging modeling task which the authors have previously described and validated. Capturing the metal-air interface, on what are inevitably complex three dimensional geometries, results in highly computationally expensive simulations and simulating a single cast can take weeks on a single processor. This contribution reports on modeling a complex centrifugal cast, gas entrainment, bubble transport and solidification, employing meshes of up to a million elements and investigates the scalability of the model on high performance clusters.Introduction The ultimate goal of any casting procedure is to produce a defect-free product. For difficult to cast alloys, such as Titanium, centrifugal casting has a number of advantage over conventional gravity methods [1]. In the casting of thin sections, such as turbine blades, the metal is forced into the thin sections under centrifugal forces. The centrifugal force can overcome the backpressure due to surface tension and the metal can fill mould sections with thicknesses substantially less than a millimeter. However, the materials used in these castings [2] tend to be highly reactive and requires low superheat. High liquid metal velocity gives rise to a high risk of free surface turbulent flow and of associated entrainment through free surface turbulence [3] and trapping of gas present in the flow [1]."

Jan 1, 2012

By Ligang Zhang, Wen Chen, Xinghua Liu, Jialin Li, Xiaoyin Liu, Zhenhong Liao

A research-scale fluidization and magnetization roasting device was developed to evaluate a processing option that might offset the complexity and high cost of the conventional magnetization roasting process on siderite. In this study, the operating parameters of the fluidization and magnetization roasting device for siderite were evaluated through cold-flow tests and magnetization roasting tests. The reaction mechanism functions of the fluidized roasting process are revealed with kinetic studies.

Jan 1, 2015

By Jafar Safarian

A new kinetic modelling technique has been applied to study the rate of MnO reduction from slags by dissolved carbon in liquid iron. Based on a consideration of the fundamental reaction kinetics, a general differential equation for the slag reduction process has been formulated, which then is solved analytically for certain special cases. By re-writing the solutions in a dimensionless form the poorly known kinetic constants are eliminated, which makes the model both flexible and applicable to a wide range of experimental conditions. For example, changes in process parameters such as temperature, metal composition, slag composition, gas composition can readily be captured along with variations in the crucible geometry. Based on a comparison with a series of experimental reduction curves being reported in the literature, it is concluded that the predictive power of the model is surprisingly good, yielding outputs that are both reliable and physically reasonable. An attractive feature of the model is that it provides an alternative way of calculating the activation energies from experimental reductions curves. For example, it suggests that the activation energy for the reduction of MnO by dissolved carbon in liquid iron is about 90 kJ/mol, which is different from the previously reported activation energies. The model also suggests that the crucible geometry, which affects both slag the volume and the resulting slag/metal interfacial area, has a significant influence on the overall reduction kinetics. This design parameter is a key to further optimisation of the process on an industrial scale.

Jan 1, 2006

By Emilia Visileanu, Eftalea Carpus

"Due to the demographic explosion and development without precedent of the consumer society, the capacity to destroy the ecological balance the entire planet life depends on, acquire new dimensions. In this context new approaches on society development are imposing as well as special responsibilities for stopping and preventing Earth destruction and repairing the damage already done. The zero waste is a call to action that has as an aim the changing of current mentality of human society. ”take, use, throw away”. The zero waste is a policy, a way, an aim and represents a new approach planned for the XXI century that include the resources preservation principles, pollution reducing, increasing of the opportunities to create new work places and providing the highest degree of the.1. INTRODUCTIONThe zero waste is a call to action that has as an aim the changing of current mentality of human society. ”take, use, throw away”. The zero waste is a policy, a way, an aim and represents a new approach planned for the XXI century that include the resources preservation principles, pollution reducing, increasing of the opportunities to create new work places and providing the highest degree of the economy stability.2. ECOLOGICAL CONCEPTSA long-living Romania means:The closing of the production cycles, by waste reusing and recycling; the reducing of the use of fossil fuel; the improving of the material qualities, for extending the economical life of the products made by these materials; the reducing of the transport traffic.In this context, ecology, the star science with the ability to conserving and renewal of the environment is making its way, having the following principles:•,everything is bind by everything – is referring to the importance which the environment has for a great number of allied fields;•,everything leads to somewhere – the principle of the indestructible property of material (in nature, there must not exist wastes);•,nature does it the best – ecology becomes the responsible science with the governing of the strategic laws between man and nature, man takes advantage of the natural resources which he cannot create by himself and nature must feel guarded and not destroyed by this alliance;•,nothing is for free – the polluter pays.The protection of the natural environment means:•, its strong knowledge and that of the interactions between the social economic system and the natural system, the foreseen of the most close and most distant consequences of these interactions;•,the rational usage with maximum economical character of the natural resources not depending on their origin;•,preventing and direct fighting against as well on the degradation of the environment caused by man, as on those produced by natural causes;•,the ability to harmonize immediate interest of the human society on long and permanent term, using the natural factors of the environment."

Jan 1, 2008

By B. Rourke, O&apos

Copper Refineries Ltd. (CRL), Townsville is Australia's largest producer and exporter of refined copper cathode. This status has been maintained by the implementation of a significant capital works program that increased the production capacity to 270,000 t/y by June 1999. In 1979, CRL was the first in the world to commission the ISA Process Technology which has now been marketed to 47 licensees worldwide. The new tankhouse design has focused particular attention on customer requirements, operational improvements, materials handling and equipment modernisation. Equipment which has been upgraded includes cranes, anode preparation, cathode stripping and scrap washing machines along with the total replacement of the electrolyte and electrical reticulation systems. Side stream electrolyte filtration has been introduced. Improvements to electrode alignment afforded by the conversion to polymer concrete cells, precise electrode location, and the upgrade of the electrode handling machines will ensure that CRL. continues to be one of the world's major quality copper cathode producers.

Jan 1, 1999

By Florian Kongoli

While calcium ferrite slags have been successfully used in continuous copper converting for the last 30 years, ferrous calcium silicate slag was proposed about 8 years ago as an additional alternative for copper smelting. Although both slags are normal extensions of each other their phase relations have not been completely clarified. In this paper the liquidus relations of both slags have been quantified at various areas that cover both of them. The existing experimental data have been first reviewed and discussed in relation to the solidification procedure. An original physical model is then used to predict various diagrams of the liquidus surface of both slags. It is shown that the ternary liquidus diagrams normally used for FeOx-SiO2-CaO system are not suitable for industrial slags. The new model diagrams of Fe/CaO versus SiO2 and Fe/SiO2 versus CaO as well as Fe/CaO versus Temperature and Fe/SiO2 versus temperature are proven to be much more convenient for ferrite and ferrous calcium silicate slags. Based on these diagrams the effect of SiO2 and CaO on the melting temperature is quantified. The effect of Cu2O is also quantified through the model. Some Fe/CaO versus Cu2O and Fe/SiO2versus CaO at various copper contents are predicted and the results show good agreement with the experimental data. It is also shown that in the presence of liquid copper, Cu2O is dissolved in the slag depending on the oxidation degree of the system and might lower the liquidus temperature. Some discussions are also presented taking into account plant observations and important conclusions are drawn for copper smelting and converting

Jan 1, 2006

By Steven Wright

The extent and the rate of reduction of slags produced from the smelting of recycled lead batteries were investigated under laboratory conditions using graphite as reductant. Simultaneous reduction of PbO, Fe2O3, Sb2O3 and As2O3 occurred at temperatures of 1180 and 1200°C, with Sb and As reporting to the metal phase while the PbO content of the slag was above 2 wt%. Fuming of As from the metal occurred at lower concentrations of lead in the slag. Discard slags with low levels of As, Pb and Sb were produced. Arsenic levels were reduced to less than accurately measurable by ICP analysis, and Sb levels in the final slags were in the range of 0.1 to 0.2 wt%. The kinetic data obtained were analysed and compared with other measurements on lead oxide containing slags. The results showing a dependence of the reduction rate on the oxidation state and the basicity are consistent with other studies on well characterised industrial and. synthetic lead slags. These results indicate that when carbonaceous reductants are used, the rate of interfacial reactions play an important role in enabling the production of environmentally acceptable discard slags.

Jan 1, 1994

By R. J. Batterham

This paper sets the scene for the Australian-Asian Pacific Course and Conference on Pyrometallurgy for complex materials and wastes. The relentless presence of competitiveness is rehearsed as the source of the current trends towards continuous improvement and benchmarking. While this might be expected to lead to more spending on pyrometallurgy, the opposite appears to be the case. The paper examines the reasons and suggests that we face an increasing challenge for selective developments that can lead to sustainable competitive advantage - both in mineral and in waste processing.

Jan 1, 1994

By S. Subhawong

Following the startup of the zinc plant in Clarksville, Tennessee, in 1978, the original effluent treatment plant did not perform as designed. The sludge, produced in a conventional lime neutralization treatment, settled poorly and began to fill the permitted lined impoundment within two years, well short of the original design capacity. Another sludge pond had to be constructed. This led to a new process modification of the original design. Although the design is still based on the conventional lime precipitation of heavy metals, the current effluent treatment plant has evolved into a hydrometallurgical circuit, capable of producing good quality water without generating sludge. Undesirable elements are bled from the zinc circuit and are rejected through the effluent treatment operations. Wallboard grade gypsum is produced, instead of sludge, and all the gypsum is sold to cement and wallboard plants. This operation also recovers and returns more than 1,500 tonnes of zinc annually to the 105,000 tonne/y zinc plant.

Jan 1, 2000

By P. Mercille, M. F. Nasmyth, J. G. Cooper

The turn of the century sees considerable activity in the zinc industry for the replacement or expansion of existing cellhouses, and the building of new cellhouses as part of new zinc projects. Aside from the cellhouse technology itself, numerous engineering and construction issues play a major role in the success of a project for replacing or building new cellhouses. The purpose of this paper is to bring to light and to address the engineering and construction factors which go beyond the selection of a cellhouse technology and which remain of key importance in implementing such projects. In addition, some implications of these factors for project costs will be illustrated.

Jan 1, 2000

By Rey B. Marquez

This paper introduces and outlines the implementation of Reliability Centered Maintenance (RCM) at Phelps Dodge Hidalgo Inc. By using a disciplined approach to the everyday maintenance functions, a proactive strategy is being developed which "raises the bar" for plant maintenance. The main objectives are: integration of Operations and Maintenance partnerships, transformation of maintenance practices from a reactive to proactive mode through the introduction of a progressive Predictive/Preventive Maintenance program (PDM/PM) paradigm changes, increased management support of maintenance functions, introduction of new indices and root cause analysis, updated; training, and definition of RCM components. RCM is the vehicle being utilized to reach the higher level of equipment availability and utilization. However, the ultimate goal is to venture beyond RCM and into the new frontier of Total Maintenance Management (TMM).

Jan 1, 1998

By Charles Washburn

The authors review mercury sources, and contaminant streams, with particular emphasis on mercury that is extracted from precious metal ores. The design and operation of both large and small mercury distillation facilities are detailed. The relevant properties and characteristics of mercury and mercury vapor are presented. Facility engineering with respect to industrial hygiene, area ventilation, and material handling is presented.

Jan 1, 2003

By V. K. Handa

Sterlite Industries (I) Ltd. started its copper smelter in 1996 and worked through the common problems associated with smelter start-ups. Specific issues in the converter area included converter blower IGV problems, punching machine reliability, converter spitting, back collar burning, ,and short converter campaign life. With a very young and dedicated team of engineers and technicians, smelter management assigned teams of three to four members to work scientifically and systematically through each major problem area to recommend and implement appropriate solutions. The converter mouth was redesigned with respect to tuyere and metal height to eliminate spitting and back collar burning. The air line was changed in places to reduce the pressure drop. A new back-up compressed air line and vessel was installed to prevent tuyere blockage in the event of a blower trip or power failure. The converter mouth liners and bricking around the mouth was modified to eliminate metal leaking through the pouring lip Modifications to the punching machines were made to address specific problems and preventative maintenance practices were further streamlined and reinforced to ensure 100% availability of hot metal cranes, converter blowers, punching machines, and ID fans. Matte availability and matte temperatures were improved by streamlining the upstream ISA and Rotary Holding furnace areas. Implementation of a detailed training program for the converter operators significantly improved the operation and morale. Water-cooled double hoods and a third converter were installed as part of the smelter modernization plan. The new hoods dramatically improved hygiene in the crane aisle while the addition of the third converter posed new challenges for the same motivated group of crews with respect to flip flop operation to keep the idle converter hot and to maximize in-stack time, managing crane/ladle logistics, and managing revert generation. This paper describes the converter operation's journey from the initial days of long blowing times and large revert accumulations to present operations with two converter flip flop operation, and also describes the team work, constant focus on increasing productivity and reducing costs, and benchmarking.

Jan 1, 2002

By Jin Liu

The mechanism and rate of carbon reduction of each of the phases that are formed in the flash flame, i.e. sulfide (matte) and oxysulfide, was investigated. Graphite-slag reduction was conducted for comparison purposes. The objective of these tests was to measure the rate of solid graphite reduction of respectively matte, oxysulfide, slag, and matte+slag mixture at different temperatures. More in particular, these tests were expected to permit understanding and explaining the reduction mechanism of each material by comparing the respective reaction rates, product reaction gas compositions and CO/CO2 ratios, reduced material assays, activation energies, and other relevant parameters. Direct visual inspection of the test crucibles would provide additional information.

Jan 1, 2006

By T. Tamagawa

Vaporization of zinc and mixing of zinc vapor with CO-CO2 mixtures were studied experimentally to prepare Zn(g)-CO-CO2-Ar mixtures with desired composition for investigating the condensation behavior and efficiency of zinc vapor. The vaporization rate of zinc was generally constant under given conditions, and could be increased by raising the flow rate of the carrier gas, temperature and vaporization area. The Zn(g)-CO-CO,,-Ar mixtures were quenched by a water-cooling sampling tube for measuring the actual composition of the mixtures in the reactor. The oxidation extent of the zinc vapor in the CO-CO2 mixtures had relation to the CO2/CO ratios and the temperatures. Under current conditions, it was necessary to employ the CO2/CO ratio below 0.125 for mixing the zinc vapor with CO-CO2 mixtures without oxidation. In addition, the appearances and zinc contents of the condensed zinc on the sampling tube were also examined.

Jan 1, 2001

By F. L. Marley

Small and medium-sized flotation plants with no assaying instrumentation still depend much upon the art of the operator to produce acceptable and consistent results. Improved performance can be accomplished by the use of the simple microscope set up as a control device. The visual recognition of products in the circuit does much to eliminate uncertain shift operating decisions and is an easy technique to acquire. Mineral staining methods further assist in the determination of components within the mill products. Simple mounting upon scotch tape and other adhesives is rapid and convenient. The microscope also has a practical role for the plant metallurgist or laboratory technician when evaluating middling products, and their routing within the circuit. Examples are reviewed where the microscope has been used for operational control in both sulfide and nonmetallic mineral flotation plants.

Jan 1, 1981

By Leandro Voisin

A new pyrometallurgical treatment alternative is proposed for cleaning complex copper matte with high content of impurities in the copper smelting process, thus, in a suitable furnace, a given amount of pig iron will be added to the liquid complex matte with a matte grade between 65 and 75 % Cu under reducing condition and will produce three liquid phases of matte, copper-rich alloy and iron-rich alloy. Hence, in this study, firstly, a mass balance calculation was made on the basis of the reported data for the distribution ratios of the components among the three phases to define the optimum condition where most of the arsenic can be fixed in the less valuable liquid iron-rich alloy. By taking advantage of the high concentration of arsenic in the iron-rich alloy, the small volume alloy may be disposed in a yard, while the precious elements may be recovered effectively in the liquid copper-rich alloy and/or in the liquid matte. Secondly, laboratory-scale experiments were conducted to apply the proposed process to the matte produced from the slag-cleaning electrical furnace and the Teniente Converter of the Codelco-Norte smelter. The obtained results indicate that the proposed process for cleaning complex matte is promising.

Jan 1, 2006

By Murray Johnston

New measurements have been made on the equilibrium distribution of selenium and tellurium between molten slag and metal phases. Distribution coefficients of Se and Te between magnesia-saturated calcium ferrite slag and copper or silver alloys were measured over the temperature range 1473 and 1673 K under controlled oxygen patrial pressures of 10-11 to 10-0.68atm. The results demonstrate that the minor elements are present in the calcium ferrite slag as the selenide (Se2-) and telluride (Te2-) respectively, up to a PO2 of 10-6 atm. As conditions become more oxidising, Te undergoes a transition to the divalent oxide whereas Se does not. Increasing the temperature was found to enhance partitioning of the minor elements to the slag. In terms of activities, at 1573 K, Se showed strong negative deviation from the ideal behaviour in the slag, while Te showed only slight positive deviation.

Jan 1, 2006