Search Documents

By Cesar O. Gomez

A procedure has been developed for mounting at random particles of mineral samples to be characterized using image analysis. The procedure is based on the generation of a random distribution of sample particles in particles of a diluent material. and the embedding of this particle mixture in an epoxy resin without disturbing the initial distribution. Two materials with atomic number similar to that of the epoxy resin were successfully used as diluents: activated charcoal and graphite. The proportion of diluent material to be mixed with the sample to have a large number of mineral particles in the field of view while keeping the occurrence of touching particles at an acceptable level was determined empirically. The randomization achieved with the procedure developed in this work was tested using as samples known mixtures of silica and pyrite particles of the same sieve class. The agreement obtained between the mass ratio of minerals used in the preparation of a particular specimen and that resulting from image analysis demonstrates that the procedure developed is successful in producing a specimen where the embedded particles are randomly distributed.

Jan 1, 1988

By M. Zamalloa

Slag foaming is an important phenomenon in many metallurgical processes. It creates large surface areas for multi-phase reactions to take place. In other applications, it protects electrodes and improves the energy efficiency by reducing radiation from hot surfaces. However, it may also be a source of serious disturbances. To control and optimize the use of slag foams, an extensive knowledge of the factors controlling the foam formation and stability is required. Slag foaming experiments were carried out using synthetic FeO-CaO-Si02 slags at temperatures ranging from 1200 to 1350 "C. A data acquisition system was used to continuously measure the foam height, gas flow rate, bubble frequency and temperature. The experimental results show that the gas injection rate has a strong effect on the behaviour of slag foams. At high flow rates and rapid bubbling, unstable foams with short decay times were created. The addition of P20, favours the foam formation and stability by lowering the surface tension of the slag. The average foam life increases with decreasing basicity (CaO/Si02). It is proposed that this is attributed to the increase of the surface viscosity due to surface adsorption of a thin film of silica, retarding the drainage of the liquid films.

Jan 1, 1992

By H. P. Wang, E. M. Perry

"Analytical solutions for investigating the solidification of casting problems with initial superheat and natural boundary conditions have been derived using an integral method. There are two moving interfaces in the solution field, one for the phase change line and the other for the superheat line. Two coupled nonlinear differential equations, representing two moving layers, were calculated by the Runge-Kutta numerical integration scheme. The solutions are in terms of six dimensionless parameters: phase change number, two Biot numbers for interfaces, diffusivity ratio, and dimensionless superheat temperature and time. Parametric studies on these parameters have been conducted to provide generic information about this phase change problem. This analytical information is extremely useful for validating numerical solutions. A simplified I-D finite element model was constructed for the purpose of comparison. The excellent agreement between the analytical and finite element solutions has proven that they are mutually validated.This validated finite element modeling tool was then used for modeling an investment casting process of a super-alloy with a simple geometry: a two-step plate. The nonlinear latent heat release, a common property of alloy materials, was approximated by several piecewise linear segments. The transient temperature response of this 2-D finite element solution, including a metal/mold gap resistance, shows excellent agreement with experimental data.This fundamental work provides a solid basis for further work on the development of a process modeling tool for the complex investment casting process.IntroductionAt present, the investment casting process is used in a variety of industries. In the aircraft engine industry, in particular, investment casting is used to produce parts ranging from turbine blades to engine frames. Because a large single casting can replace many component parts that require machining, fabrication, and assembly, this one-piece casting approach becomes a very cost-effective manufacturing process.The main constraint in using this process for mass production is the long design-to-production lead time. The standard rigging design is still an art, based on the experience of casting experts, rather than on scientific methods. Many trials are often required before making a sound final casting. In order to .reduce the number of expensive casting trials, the development of computer-aided tooling technology is needed.The fundamental physics describing this manufacturing process can be simply described. They reduce to a solid/liquid phase change problem, with two parts - first, the thermal balance of the initial superheat temperature of the molten metal and the preheat temperature of the ceramic shell through heat conduction, and second, the energy release from the mold surface to the ambient by radiation."

Jan 1, 1986

By Merete Tangstad, Eli Ringdalen

"In Norway ferrosilicon/silicon and ferromanganese production are strong with world markets of 4 % / 9 % and 4 %, respectively. Research and development in the academia mirrors the national interest; hence, there has been extensive academic research in these areas. There are some vital drivers and premises for a successful cooperation between the academia and industry with the main driver being a win-win situation for both. For industry,the potential advantages include cost-, competence- or environmental- benefits; for academia, the important drivers are building of competence and equipment, educating more students at higher levels, and increased possibilities to publish. In Norway, the benefits of cooperation between industry and academia are basic knowledge regarding thermodynamic and kinetic data, as well as reaction mechanisms within core processes. In recent years, such research interests have focused on the depletion of raw materials as well as environmental issues.IntroductionIn 1989, the Norwegian Ferroalloy Producers Research Association (FFF) was funded on the belief that a common research association would benefit the industry by making it easier to perform basic research as well as paving the ground for better recruitment to the industry. The funding partners in Norway were the FeSi/Si and FeMn producers. Today, the producers are Elkem, Finnfjord, Fesil, Wacker, Eramet and Vale. The main research partners working with FFF are SINTEF (Materials and Chemistry) and the Department of Material Science and Engineering at the Norwegian University of Science and Technology (NTNU). With more than 1700 employees, SINTEF is the largest independent research organization in Norway and NTNU is the largest technical university. Together, the two organizations provide an exceptionally strong materials technology research environment, and especially so for pyrometallurgical research."

Jan 1, 2012

By Jincheng Hu, Honggang Zhong, Qijie Zhai, Congsen Wu, Cheng Zhang, Jingzheng Ye

"The influence of cooling intensity on the solidification structure and ferrite phase content of a new duplex stainless steel (DSS) was investigated by using a thermal simulation setup for continuous casting. The results showed that the characteristics of the solidification structure were similar to their industrial scale manufactured slabs, including chill zone, colunmar zone and equiaxed zone. And austenite morphologies were mainly primary and secondary Widmanstatten sideplates as well as intragranular Widmanstatten plates. In addition, it revealed that the ferrite content increased with an increasing distance from the chill surface and decreased at colunmar to equiaxed transition (CET) position, then the value remained relatively stable at equiaxed zone. Furthermore, the ferrite content presented the same trend with the cooling intensity ranging from 100 mL/min to 2000 mL/min with the values just varying in a slight range.IntroductionThe duplex stainless steel (DSS) is the kind of steel that ferrite phase and austenite phase occupy about 50% respectively, or the content of the fewer phase has to be more than 30% [l]. The success of modem duplex stainless steels is to a large degree due to their higher strength than austenitic stainless steels, higher toughness than ferritic stainless steels, good weldability and high resistance to stress corrosion cracking as well [2,3]. The cost of stainless steel production continues to soar in recent years due to the increasingly higher price of Cr. In order to decrease the production cost, a new type of duplex stainless steel was developed by Bao steel [4]. This newly developed duplex stainless steel had low Cr content compared with 2205 DSS, and was expected to be applied into automobile industry. However, this type of steel was still in the initial stage of development, and the influence of continuous casting process on its solidification process and structure was still unclear, which needed to be studied further. Several works published in literature presented the effect of continuous casting conditions on duplex stainless steel (DSS) 2205, 2304 [5,6]. It was discussed that the cooling intensity in the chill-side had little efficient influence on the phase transformation. In this paper, the effect of cooling intensity on the solidification structure and ferrite volume fraction of this DSS at a given cooling rate was investigated."

Jan 1, 2014

By A. A. Hejja

The first part of this study deals with the importance of surface tension of slags produced in the smelting of sulphide concentrates. Theoretically the method of determining the surface tension of slags was laid down by Boni and Derge. The values obtained experimentally for a series of main oxide components were grouped into a useful correlation incorporating experimental constants for the relevant oxides present in the slag, some of these giving the surface tension value for the particular slag. These estimated values were coupled with or incorporated into the slag viscosity plots to show the correlation between the two factors. This is also important from a refractory attack point of view in the furnace operation. In the second part an attempt is made toward the optimisation of slag composition relevant for electric furnace smelting processes. Using the knowledge of the viscosity and electrical conductivity of the slags at the temperature of furnace operation, the mode of optimisation is based on correlations which utilize the trend of the mostly parabolic plots of viscosities and conductivities. The results obtained by this method agree well with the optimum slag compositions being used in established operations derived from years of practical experience for various slags used in the furnaces. However, due to extensive turbulence in suspension and gas injected bath smelting processes, the outlined methods cannot be used for these processes. Also great caution should be exercised in their application for three electrode circular furnaces with separate slag cleaning.

Jan 1, 1997

By Mark Jolly, Nasim Soleimanian

"During the last 20 years CFD (Computational Fluid Dynamics) has been used as a tool to aid furnace designers and manufacturers to improve energy efficiency and effectiveness of glass furnaces. However as the models are maturing the effect of feeding equipment used to push the raw material into the furnace has not been included in the process models. This paper investigates the effects of batch pattern in the melt space caused by charging equipment on the energy efficiency of the furnace focusing on the melting zone. A simple batch patterns sensitivity study has been performed using purpose built software (Glass Furnace Model-GFM). It is concluded that in order to further reduce the energy consumption of the furnace it is necessary to model the batch charging process in more detail to find more opportunities for improvement.Introduction Glass manufacturing is a conservative industry which applies to all the four major segments (float glass, container glass, fiberglass, and specialty glasses). Risks due to the high capital investment, very long service life of the furnaces, and the demand for high performance and quality from the outset translates into evolutionary progress rather than revolutionary. The main problem facing glass manufacturers are the financial cost of manufacture, its impact on the environment, and mounting pressure imposed by the authorities for greener manufacturing and reduction in emissions.The main energy intensive activities involved in continuous glass manufacturing are: the need for high temperature to create and maintain the viscous flow, homogenisation of glass melt (melt residence time), and maintaining the two to achieve continuous output of glass at the right quality. The high temperature and long duration of homogenisation has resulted in the design oflarge furnaces, which have high energy consumption, low specific performance, and high C02 emissions. As an example in the container glass sector the most efficient furnace has a specific primary energy consumption of 3.8 GJ /tonne of glass at a level of 50% cullet in the batch. Even very small improvements in efficiency by optimising operation would have a high impact [1-14]. Given the conservative nature of the industry and the costs involved in experimental data gathering, CFD modeling of the process has been used extensively during last two decades to not only improve our understanding of the process but also as a tool in predicting possible optimisation windows, e.g. Glass Furnace Model ( GFM), a commercially available piece of software that has been developed to optimise furnace operation."

Jan 1, 2013

By P. T. Velu

Solubility of metal oxides in the molten salt electrblytes is an important parameter in the electrochemical processing of metals and alloys. The efficiency of an electrochemical process primarily depends on the quantity of metal oxide present in the electrolyte in the dissolved form and its thermodynamic properties. The activity of CeO2 was calculated using the free energy of fusion of CeO2,{ AG°m, CeO2. The AGOm,CeO2 }was deduced from the values of enthalpy, heat of fusion and melting point of Ce02. The activity coefficients of CeO2 as a function of temperature and melt composition were calculated. The thermodynamic data such as integral molar enthalpy, entropy and Gibbs energy of formation were calculated as a function of composition and temperature.

Jan 1, 1994

By Victor Stancovski, Uday Pal, Stephen C. Britten

"An in situ electrochemical technique for measuring the concentrations of easily dissociable oxides in slags at temperatures between 1200-1600°C is being developed. The technique utilizes a partially-stabilized-zirconia solid electrolyte (PSZ), which conducts oxygen ions, to separate a reference-gas compartment from the slag of interest. Three types of measurements are currently under investigation which yield different information concerning the slag phase and hence will be combined into a single amperometric device for monitoring the properties of easily dissociable slags.Type I utilizes an open-circuit-voltage measurement between the reference gas and the slag phase. Type II utilizes a potentiostat to apply a direct current potential step or sweep between the inner and outer compartments of the electrolyte, driving oxygen ions from the slag into a reference gas. With the use of open-circuit-reference electrodes, the resulting current-potential profile reveals the dissociation potential and concentration profile of dissociable oxides such as those of iron, manganese, and chromium. Information on the transport properties of the cations can also be generated from these measurements. Type III utilizes a potentiostat with reference electrodes to carefully electrolyze a known volume of slag by removing large quantities of oxygen ions from the slag to the reference gas. The coulombs of charge removed at different applied potentials can be used as a direct indication of the concentration of each dissociable oxide species present within the slag."

Jan 1, 1997

By N. El-Kaddah, V. L. Acoff, M. Arenas

"Control of the weld penetration, weld pool shape and temperature field in arc welding is critical to achieve the desired microstructure and mechanical properties in the resultant welds. This is particularly important in welding gamma titanium aluminides (y-TiAl) where the weld pool is relatively shallow and the temperature gradient in the heat-affected zone is quite steep. This paper investigates theoretically and experimentally the evolution of the shape of the weld pool for stationary gas tungsten arc welds in y-TiAl alloys. A mathematical model has been developed for predicting the electric current flow, the resultant electromagnetic forces in the metal, and the transient development of the temperature and velocity fields in the molten pool generated by a spatially variable heat flux at the arc-striking zone. The governing equations were solved numerically using the control volume technique. Welding experiments were carried out to determine the shape of the weld pool and the extent of the heat affected zone at different welding times for model validation. The numerical predictions were found to be in reasonable agreement with measurements. It is suggested that the model presented in this paper is likely to provide the information needed for predicting the microstructure and mechanical properties of y-TiAl welds. IntroductionIn recent years, there has been considerable interest in the welding of gamma titanium aluminides as a means of manufacturing high-temperature, high-performance components for turbine and automobile engines. These alloys are highly reactive, and must be welded in vacuum or inert gas atmosphere, rendering electron beam, and inert gas tungsten arc welding (GTA) to be the only suitable welding techniques for joining these materials [1-3]. The GTA welding is especially attractive because of its flexibility and relative cost-effectiveness. However, previous studies on the weldability and weld properties of these alloys using this process revealed a decrease in the mechanical properties in the fusion zone [4]. This is generally attributed to the change of the original duplex structure to a dendritic structure amplified by the shallowness of weld spot. Quantifying the effect of arc operating parameters on the geometry and temperature profile of the welding pool prior cooling is the first step for controlling the fusion zone microstructure and mechanical properties."

Jan 1, 1999

By Yousef Mohassab, Feng Chen, Hong Yong Sohn, Mohamed Elzohiery

The determination of reduction degree in a DR process is sensitive to the total iron in the ore and DRI. An accurate and high throughput analysis method for total iron has been developed. Titration of the solution after tin(II) chloride reduction of ferric ion is a widely used method for iron analysis. However, it is a multistep method that requires many chemical reagents and much time. In this work, an ICP-OES analysis method with higher or equivalent accuracy compared with the titrimetric method was developed. This method has much higher throughput and demands fewer chemical reagents compared with the titrimetric method. In this paper, a comparison of the two methods is presented.

Jan 1, 2016

By Robin M. Forbes. Jones, Suhas V. Patankar, Ramesh S. Minisandram, Jr. Carter, Kanchan M. Kelkar

"The nucleated casting process currently under development has the potential for production of Ni-base superalloy preforms that possess superior microstructure to product made by conventional casting processes, primarily for gas turbine applications. In this process, electroslag remelted (ESR) clean (i.e., free of ceramic inclusions) molten metal is conveyed via a watercooled copper Cold-walled Induction Guide (CIG) to a gas atomizer. The spray of clean metal droplets is then directly cast into a water-cooled crucible for ingot production. The microstructure of the resulting ingot preform evolves within the length scale of the individual droplets and is a function of the thermal state of the incoming metal droplets. This, in turn, depends on particle size, flight time and heat exchange with the gas phase.In the present study, computational models is developed for the analysis of the flow and heat transfer in the gas-metal spray system under axisymmetric and steady-state conditions. The gasphase flow is analyzed using an Eulerian framework and turbulent mixing within the gas phase is modeled using the two-equation k-e model. The dynamics of the metal particles is analyzed using a Lagrangian framework that involves calculation of the trajectories of the metal droplets. A two-way coupling is considered whereby the transport and heat transfer in the gas and the metal phases influence each other.The analysis is developed at two levels. The spray model performs a detailed calculation of the spray dynamics in the vicinity of the spray and is intended for predicting the temperature and mass flux distributions of the metal spray depositing into the mold. The chamber model enables prediction of gas flow and motion of metal particles in the entire spray chamber."

Jan 1, 2004

By Guojun Ma

The entrainment of charge materials, evaporation or volatilization of elements and ejection of slag and metal by spitting or the bursting of gas bubbles are mechanisms whereby stainless steel plant dust are generated from the electric arc furnace and refining converter. TCLP and ASTM D 3987-85 tests on dust that was collected from the baghouse filter system of a South African Stainless Steel plant showed that this dust can be considered hazardous according to South African legislation, due to the high degree of Cr (VI) leachability (~13mg/l for TCLP and ~8mg/l for ASTM vs. regulation threshold of 0.05mg/l in drinking water). The dust is therefore considered to be harmful to both the environment and human health, due to its high solubility in water and carcinogenic properties. It should therefore be treated before being stockpiled or land filled. This paper consequently describes an investigation into the formation of Cr(VI)-containing stainless steel plant dust and the stabilisation thereof in a sintering process, whereby the dust was mixed with a silica-rich clay. It is postulated that Cr(VI) form when the (Mg,Fe,Mn,Cr)3O4spinel phase, CaO, Ca(OH)2 and CaF2 (all of which are present in the dust) react. This reaction was found to take place both at ambient and at high temperatures (1100°C). Stabilization of Cr(VI) in the dust could be achieved at an optimum sintering temperature of 1100°C for a 50mass% dust : 50mass% clay mixture. Chromium emission during the sintering process was found to be low, and within environmental limits.

Jan 1, 2006

By A. G. Guézennec

Electric Arc Furnace (EAF) steelmaking co-produces amounts of dust (15 to 25 kg per ton of steel), which require to be collected and stored in specific landfills. The collection, handling, and possible beneficiation of EAF dust depend on its composition and morphology. We first studied theoretically the chemical evolution of dust particles along the fume extraction system, from the furnace down to the filters, using thermodynamic calculations of the Fe-Zn-O system. We show how it would be possible to favor zincite formation in dust and therefore increase further zinc recovery. Then, we developed a new morphological model, based on population balances, for predicting the granulometric evolution of dust particles as a result of agglomeration and sintering in the fume extraction ducts. The contribution of the various mechanisms (Brownian, turbulent, and sedimentary agglomeration; thermophoretic deposition; coalescence and sintering) is assessed. The influence of the exhausting conditions on dust granulometry is detailed. For the extraction system studied, intense agglomeration of the sub-micronic particles and complete coalescence take place inside the furnace; micronic particles then undergo little evolution from the elbow to the water-jacket, whereas big agglomerates are formed downstream. These results are in good agreement with dust particle observations.

Jan 1, 2006

By Ma Keyi, Yang Xianwan, Zhu Xiaoyun, Guo Zhongcheng, Zheng Yanping

"The oxidation of the Multifunctional Electrodeposited RE-Ni-WP- SiC Composites at high temperature is investigated. The results show that during high temperature oxidation the relationship between the mass change of pure Ni , Ni-W-P, Ni-W-P-SiC or RE-Ni-W-P-SiC coating and the oxidation time follows a mixed curve, i.e. it is approximately a linear relationship when the oxidation time is less than 60 mins while it is a power function relationship when the oxidation time is over 60 mins. The order for the oxidation rate of the four coatings is Ni> Ni-W-P> Ni-WP- SiC>RE-Ni-W-P-SiC. The mass change of Ni-W-P, Ni-W-PSiC or RE-Ni-W-P-SiC coating increases exponentially with a rise of oxidation temperature. The high temperature-oxidation resistance of RE-Ni-W-P-SiC composite coating is 3-4 times that ofNi-W-P alloy coating. The cross section morphologies and Xray diffraction patterns indicate that the high temperature oxidation resistance of RE-Ni-W-P-SiC composite coating is better than any other coatings.1. IntroductionWith the rapid development of modem industries the products in engineering industry are continually challenged by the requirements of long-term and stable working at higher temperature, pressure, speed and under adverse conditions. Consequently, the surface properties of the products, such as the resistance to oxidation at high temperature, the resistance to wear and the resistance to corrosion, should be improved continually."

Jan 1, 2000

By Hiroaki Nakano, Kenji Hara, Shunsuke Kawano, Takeshi Ohgai, Michiaki Ikeda, Hisaaki Fukushima, Shinji Yamashita, Tetsuya Akiyama, Hisayuki Kaku

"Ni-Fe alloys have an inverse magnetostrictive effect (Villari effect) in which its permeability varies according to the ·applied strain. This alloy film has a potential for application as force sensors such as torque sensors, tension sensors and so on. Electrodeposition is promising as a technique for preparing Ni-Fe alloy film because of its convenience and economy. In this paper, the effects of electrolysis conditions on the magnetic properties of electrodeposited Ni-Fe alloy films were investigated. Hysteresis loops of Ni-Fe alloy films on copper substrates from sulfate bath were measured by a vibrating sample magnetometer (VSM). The films of low coercivity, which were preferred when used as a force sensor were obtained by introducing certain additives to the sulfate type bath.INTRODUCTIONNi-Fe alloys show an inverse magnetostrictive effect (Villari effect) that their permeability varies depending on the applied strain. The films of this alloy have a potential for application as force sensors such as torque sensors, tension sensors and so on. The authors et al. tried to prepare Ni-Fe alloy films using the sputtering technique, and produced a prototype of Ni-Fe alloy torque sensor [I]. The sensitivity was higher in the torque sensor thus produced than the strain gauge type one, and this torque sensor enables non-contacted detection. It showed excellent durability and reliability. However, the formation of Ni-Fe alloys by sputtering requires higher costs and brought an another problem that the shape of the substrate on which the film was formed was considerably limited. This causes a hindrance to the wide-range application of the force sensors. Electrodeposition is promising as the technique for preparing Ni-Fe alloy films because of its convenience and economy. In this paper, the effects of the conditions of electrodeposition on the magnetic properties of Ni-Fe alloy films were studied."

Jan 1, 2000

By Vladimir Lobanov, Vladimir Skorohodov, Andrew Evdokimov, Ural State Technical University 19, Boris Radionov

"The bulk of raw materials in metallurgy of secondary platinum metals are the wastes such as multilayered ceramic-metal systems, e.g. the spent catalysts of the chemical and petrochemical industry, automobile catalysts, etc. Due high chemical resistance of a ceramic basis the extraction of platinum metals by leaching even at very fine crushing is poor. The study of sorption leaching of platinum and a palladium from the spent automobile catalysts are carried out. The average content of PGM is 0.5%. A few methods of raw materials sampling were compared: 1) direct hydrometallurgical leaching of platinum metals from the fine-grained catalyst and atomic absorption analysis of the obtained solutions; 2) fusion to a metal or sulphidic collector of precious metals with the alloy analysis by direct spectrometry; 3) fusion with dissolution of a precious metals collector and atomic absorption analysis of PGM in solutions. Leaching allows detecting out no more than 90% of a palladium and 80% of platinum. Fusion to a collector gives the best results at the chemical ending. Researches on sorption leaching are executed. Under optimum conditions the extraction of platinum metals to concentrates is comparable with similar indicators of collector fusion.The large part of raw materials in metallurgy of secondary platinum metals are the multilayered or tridimensional ceramic-metal systems, in particular the spent catalysts of the chemical and petrochemical industry, automobile catalysts, ceramic-metal condensers, etc. The content of the sum of PGMs can be from hundreds grams per ton to several percent. For processing of such materials the hydrometallurgical methods of platinum metals leaching by various reagents are used commonly. High chemical resistance of the ceramic basis covering the metal particles causes low recovery even at very fine grinding. Other fundamentally different method of catalysts opening includes dissolution of the ceramic basis in the solutions of hydrofluoric acid and the subsequent recovery of platinum metals from insoluble residue. Application of this method is associated to use of corrosive medias and appropriate equipment. Fusion of the specified materials with collecting of PGM by copper, nickel or lead at the specialized enterprises provides higher extraction in semiproduct. At the same time, complexity and duration of the subsequent extraction of platinum metals concentrates causes high total cost per unit. Thereby this method is economically acceptable only for rather poor raw materials (no more than 0,1%). Undoubtedly, that the raw materials with the high content of PGM are reasonable to process by individual technology. In the present work the processing of some kinds of ceramic-metal raw materials, particularly automobile catalysts (neutralizers) with various collectors at the conditions of a target fusion are investigated."

Jan 1, 2008

By Toshiyuki Hashida, Victor M. Lopez-Hirata

"Small-punch tests and determination of fracture toughness JIC were conducted at 4 and 77 K on new cryogenic JN1, JJ1 and JK2 austenitic stainless steels, after isothermal aging. Equivalent fracture strain ?qf determined by measuring the reduction of thickness in the small-punch test specimen. A linear dependence of JIC on ?qf was found in these new materials. Regression analysis of experimental data produced the following linear relation JIC = 1304.1 ?qf + 8.09 [kJm-2]. An analysis of present work relation was pursued on the basis of material properties and evaluation method of he. Results showed that the slope value has a strong dependence on material yield strength and JIC evaluation method. This linear relation is useful for the evaluation of fracture toughness JIC, measuring the equivalent fracture strain ?qf by means of small-punch test. Thus it can be useful for assessing the degradation of fracture toughness in small areas such as, the heat-affected zone in welded components.IntroductionCryogenic structural materials for superconducting magnets of fusion nuclear reactor are required to possess a good combination of strength and toughness. The mechanical properties are required beyond the capability of conventional austenitic stainless steels [1]. New cryogenic JN1, JJ1 and JK2 austenitic stainless steels were developed by the Japan Atomic Energy Research Institute (JAERI) [1]. The structure of superconducting magnets is constructed by welding of 200 = thick plates of these steels, which are solution treated at high temperatures and then water-quenched to avoid intergranular precipitation. However, the welding process involves heating and cooling [2], which cause microstructural changes in both base metal and weld. In this heterogeneous microstructure, it is important to estimate the fracture toughness of these materials at cryogenic temperatures. Therefore, it is necessary to evaluate the effect of aging process on the fracture toughness behavior of these new steels. To determine the cryogenic fracture toughness, the elastic-plastic JIC value has been co=only used [2]; however, the specimen size is much larger than heat-affected zones in welded components. Small-punch (SP) testing method, employing miniature specimens, has permitted to evaluate the fracture toughness behavior at different temperatures in different nuclear reactor materials [3,4]. Mao et al. [5,6] and Misawa et al. [7] found a linear relation between JIC value and equivalent fracture strain ?qf, determined by SP method in non-ferrous alloys and ferritic steels at room temperature and austenitic stainless steels at 4 and 77 K, respectively. So that, this kind of correlation would be very useful to assess the fracture toughness JICe values by means of SP test in small zones of welded components."

Jan 1, 2012

By Che Xin, Liu Tianlong, Bi Hongyun, Chen Lijia

"High-cycle fatigue experiments were conducted at 800°C in laboratory air for three ferrite stainless steels including 15CrNbTi, 15CrMoNbTi and 18CrNbTi, where the stress ratio of 0.l was adopted. The experimental results show that at 800°C, the fatigue limit of the 15CrMoNbTi steel is the highest, the fatigue limit of the 15CrNbTi steel is slightly lower than that of the 15CrMoNbTi steel, and the fatigue limit of the 18CrNbTi steel is the lowest. At the same maximum stress, the 15CrMoNbTi steel has longer fatigue lives than the 15CrNbTi steel in the low stress area, while the 18CrNbTi steel has the shortest fatigue life. In addition, the observations on the fracture surfaces of fatigue specimens reveal that the fatigue cracks initiate transgranularly at the free surface of the specimens and propagate in a transgranular mode.IntroductionIn modem automotive industry, the manufacturers have paid great efforts to clean exhaust gas and to improve fuel economy. It is thought an effective way to increase the temperature of combustion chamber in automotive engine. And thus, the manifold closed to the engine in automotive exhaust system can suffer high temperature up to approximately 1000°C. Because of their relatively low thermal expansion coefficient, high yield strength at elevated temperature and good fatigue resistance, ferrite stainless steels, especially added with alloying elements such as Mo, Nb and Ti, are increasingly used for automotive exhaust systems [1-3]. In fact, exhaust manifold operated under high frequency vibration and exposed to high temperature exhausting gas also requires good fatigue resistance at elevated temperature. Some studies on the high temperature fatigue characteristics of stainless steel have been documented. It has beeen found that the fatigue limit of four ferrite stainless steels including 409L, 436L, 429EM and 444 (18Cr- 2Mo) reduces significantly with increasing temperature [4, 5]. In the research concerning the effect of a-phase embrittlement on fatigue behavior in a high-chromium ferrite stainless steel, it is noted that the precipitation of brittle a-phase will reduce the crack initiation and growth resistances and result in a decrease in fatigue limit [6]. In this investigation, the high-cycle fatigue behavior of three ferrite stainless steels including 18CrNbTi, 15CrNbTi and 15CrMoNbTi at 800°C have been studied to address the mechanical aspect of high-cycle fatigue behavior for ferrite stainless steels and to provide the theoretical reference for the safe design of automotive exhaust system."

Jan 1, 2013

By Masahiro Sasaki, Wu Kepeng, Chang-Yong. Kang, Kohji Okada, Naohiro Igata, Kazuya Miyahara

"The damping capacity of the Fe-12 mass % Cr-6 to 30 mass % Mn alloys has been investigated. Particularly the effects of microstrucutre composed of the phases of a , a ' , y , and e on the damping capacity have been clarified. Various fraction of these phases were formed depending on the Mn content and cold work degree. The combination of 22 mass % Mn and 50% cold rolling formed the largest volume fraction of e martensite and showed the highest damping capacity. The other phases of a, a' and y had very small effect on the increasing of damping capacity.IntroductionFe-Mn alloys are known to be one of the high damping capacity materials [l-3]. In the present research, the damping capacity of the Fe-12 mass % Cr-6 to 30 mass % Mn alloys, in which 12% Cr is added for the improvement of corrosion resistance of the Fe-Mn alloys, has been investigated. Particularly the effects of microstrucutre composed of various phases of a (bee), a ' (bet martensite), y (fee), and e (hcp martensite) on the damping capacity have been clarified. The results of preliminary research on Fe-Cr-Mn alloys are reported by Igata et al. [4] Various volume fraction of these phases were formed depending on the Mn content and cold work degree. The combination of 22 % Mn and 50% cold rolling formed the largest fraction of e martensite and the measurement indicated clearly that e martensite had the largest effect on the damping capacity. The other phases of a ' y and a I had very small effect on the increasing of damping capacity."

Jan 1, 2000