Search Documents

By Bruce H. Baker

Studies of used or unused refractory materials are excellent examples of applied mineralogy in industry. Refractory materials are mineral substances containing ceramic or chemical bonding systems. Knowledge of the mineral composition, bonding, and textural relationships often explains the resulting physical property values of a refractory and contributes to the interpretation of refractory wear mechanisms occurring in steel plant service.

Jan 1, 1982

By C. A. Silva

Ladle change-over, during continuous casting of steel, initiates transient flow in the tundish which influences the inclusion content and degree of mixing between two consecutive batches of steel. The mixing behavior in the tundish during this period is determined by the casting rate and the ratios of: inflow to outflow during the refilling period; and, the low liquid level relative to the nominal level in the tundish during the transiency. A 3:10 scale water-model of a typical one strand slab caster was operated in conjunction with a tracer technique to characterize the velocity fields for several combinations of these parameters. Steady operation, a limiting case of the transiency, provided a basis for comparison. High-order moments -- skewness and kurtosis -- of the residence time density function have been utilized as signature elements associated with a particular residence-time distribution for the system. A simple mathematical model incorporating the above parameters as well as a characteristic Peclet Number was successful in simulating the features of the transient period.

Jan 1, 1993

Thermodynamics and kinetics? of the removal of Va elements (As,Sb,Bi) from copper were investigated 1n the fire relining by alkaline carbonate fluxes such as Li 2co3 , Na 2CO3 and K2CO3. The distribution coefficients of As, Sb and Bl between alkaline carbonate fluxes and mo) ten copper were ?obtained at 1200°C under the different oxygen potentials. As and Sb were easily removed from copper to fluxes as pentavalent oxide form. On the other hand, Bi was hardly removed except by a Ll2CO3 flux. The removal rates of Va elements from copper were also measured In the temperature range of 1150°C.- 1250°C. The removal rates of As and Sb were much higher than that of Bi. The removal rates of Va elements showed the same order of the distribution coefficients. The removal rate could be expressed by following equation. (1).

Jan 1, 1987

By Xiaojian Zuo, Yihua Han, Qingguo Xue, Jingsong Wang, Lintao Wang, Rongzong Lan

"Using the facility of reduction experiment, the low temperature reduction pulverization and reduction behavior of sinter in oxygen blast furnace (OBF) were studied. Through analyzing the results, the difference of pulverization and reduction behavior of sinter in OBF and conventional blast furnace (BF) were discussed. Furthermore, the effect laws of reduction temperature and the content of CO and H2 on reduction behavior of sinter were studied. Also the controlling step of iron oxide reduction was discussed. Compared with BF, the low temperature reduction pulverization of sinter became serious at 773 K; reduction rate became faster at 1173 K; reduction time became less and final reduction degree was increased in OBF. With increasing of H2 and CO contents, the reduction of sinter was promoted. The reduction process was controlled by interface chemical reaction at the earlier stage and by interface chemical reaction and internal diffusion at the final stage.IntroductionThe new ironmaking technology of Oxygen Blast Furnace (OBF) is most likely to be used in large-scale application process. The concept relies on the removal of the CO2 contained in the top gas of the blast furnace. Therefore the useful components, i.e. CO+H2, can be recycled back into the furnace and reused as reducing agents. In addition, injecting oxygen (O2) into the furnace instead of preheated air, removes unwanted nitrogen (N2) from the gas. Under the pressure of CO2 emissions in iron and steel making, the growing international shortage of coking coal resources and the rising price of coke, OBF has attracted attentions of both domestic and foreign researchers, because it has so many advantages such as high productivity, high PCI rate, low coke rate, high gas reducing capability and high top gas calorific value, etc [1-7]. As a result of recycling most of the top gas after CO2 removal and injecting oxygen into the furnace, the reduction capacity of blast furnace gas will be increased, so the metallurgical behavior of OBF's iron burden is different from traditional blast furnace. Therefore, it is one of the keys to develop this technology, which studies the metallurgical behavior of sinter in OBF. The purpose of this paper is to study the low temperature reduction pulverization and reduction behavior of sinter at the atmosphere of OBF, which includes the difference of low temperature reduction pulverization and reduction behavior of sinter in oxygen blast furnace and conventional Blast Furnace (BF). It will provide theoretical basis for the development of OBF."

Jan 1, 2012

By Nagy El-Kaddah

"One of the emerging technologies for the production of ultra-clean metals is electromagnetic filtration. The theory and the mechanism of electromagnetic separation of inclusions from molten metal are briefly reviewed along with basic electromagnetic separation systems. This paper focuses on inclusion removal in the induced current separators, with specific reference to a new separator developed at the University of Alabama. A simple analytical model is presented for the analysis of particle separation in such a system. The role of the applied magnetic field on inclusion removal will be discussed. It is shown that particle velocity increases exponentially with increasing magnetic field strength. At moderate field strengths, the velocity of 50 to 100 u. inclusions· are an order of magnitude larger than those achieved by buoyancy. The separator developed at the University of Alabama is described together with experimental results of laboratory and large scale experiments on purification of molten aluminum. These results demonstrate the capability of the system for producing super-clean metals.IntroductionThe nature of extraction, refining and processing of metals is such that oxides and other non-metallic particles will always be present. This is due to the highly reactive nature of metals with oxygen and other non-metallic elements. The presence of these type inclusions in metals, even in minute amounts, can seriously flaw the reliability and performance of the final product. They not only reduce the strength and the stiffness of the metal/1/, they are the reason behind many of manufacturing defects such as porosity in castings, surface and internal cracks in continuously cast ingots and rolled products, etc., which act to cause premature failure of manufactured parts. In fact, for critical applications such as turbine blades, there is virtually no tolerance for inclusions above ten microns in size /2/. Therefore, removal of inclusions from the liquid metal is an essential processing step.The demand for cleaner metals has brought major changes in the technology and practice of metal refining and casting. Inclusion removal from the melt is currently achieved by passing the melt through a series of melt treatment systems, including induction stirring furnaces, argon-stirred ladle, and ceramic foam and deep-bed filters /3,4/. These systems are generally capable of removing all inclusion particles above 50 microns in diameter, which meets current cleanliness requirements for most applications. However, they may not be able to meet the projected cleanliness levels for critical applications due to kinetic and operational limitations of these systems in removing smaller particles /5/."

Jan 1, 1996

By J. Leon-Torres, D. M. Stefanescu, P. A. Curreri, S. Sen

"Experiments were performed under terrestrial gravity (lg) and during parabolic flights (10·2 g) to study the solidification and macrosegregation patterns of Al-Cu alloys. Alloys having 2% and 5% Cu were solidified against a chill at two different cooling rates. Microscopic and Electron Microprobe characterization was used to produce rnicrostructural and macrosegregation maps.In all cases positive segregation occurred next to the chill because of the shrinkage flow, as expected. This positive segregation was higher in the low-g samples, apparently because of the higher heat transfer coefficient.A 2-D computational model was used to explain the experimental results. The continuum formulation was employed to describe the macroscopic transports of mass, energy, and momentum, associated with the solidification phenomena, for a two-phase system. The model considers that liquid flow is driven by thermal and solutal buoyancy, and by solidification shrinkage. The solidification event was divided into two stages. In the first one, the liquid containing freely moving equiaxed grains was described through the relative viscosity concept. In the second stage, when a fixed dendritic network was formed after dendritic coherency, the mushy zone was treated as a porous medium.The macrosegregation maps and the cooling curves obtained during experiments were used for validation of the solidification and segregation model. The model can explain the solidification and macrosegregation patterns and the differences between low- and high-gravity results."

Jan 1, 1999

By V. Ramachandran

The Amarillo Copper Refinery, the newest and most modern copper refinery in the world, has been in operation for the last eleven years and has a rated capacity of 460,000 st/yr. The tankhouse - a structure that covers 500,000 ft2 under one roof - extends one-half mile in length and is a model of materials-handling efficiency. The use of recently developed and patented* reagent control technology, termed "Reatrol Process", has increased current efficiencies to an average of 98% and has considerably improved the physical and chemical quality of the cathode deposit. The present paper describes the current operations at the Amarillo Copper Plant with special emphasis on tankhouse operation.

Jan 1, 1987

By P. R. Taylor

Titanium carbide and titanium diboride powders have been successfully synthesized by direct treatment of ilmenite concentrates in a non-transferred arc thermal plasma reactor. Methane gas was used as the reducing agent and boron oxide was used as the boron source in these processes. Free energy minimization plots were used to predict the behavior of each system under different molar ratios and operating conditions. Products were characterized by XRD, SEM and chemical analytical techniques. The average size of the ceramic product is in the submicron range. Metallic iron apparently is finely deposited on the surface of the titanium carbide or titanium diboride particles. Minor impurities such as silica, manganese and zircon were converted to the carbide form.

Jan 1, 1995

By Sheng-li Wu, Guo-liang Zhang, Bo Su

The mineralogical characteristics of iron ores can influence their high temperature sintering performance. In this study, eight iron ore samples from Brazil, Australia, and South Africa were characterized by their chemical composition, mineral types, particle morphology, and gangue dispersity. Meanwhile the influence rules between the mineralogical characteristics and the high temperature characteristics were evaluated and analyzed. The results showed that the effect of SiO2 on assimilation characteristic of iron ores was relatively complex, Al2O3 and LOI of iron ores had negative correlation with assimilation temperature of iron ores, the dense slab-flaky mineral granule restrained to the assimilation characteristics of iron ores; liquid phase of iron ores with high SiO2 content and low Al2O3 content had high fluidity, and the higher dispersity of gangue minerals in iron ores was good to the fluidity of liquid phase.

Jan 1, 2015

By Ryokichi Shimpo

Much amount of sludge is produced from the wastewater treatments in surface finishing industry. There are many problems for the abandonment of the sludge because of the high water content and heavy metals included. It is often observed that hexavalent chromium, which is toxic, is generated in the course of heat treatments of the sludge for reducing its amount by dispersing water. In this study, conditions of the sludge calcinations for reducing water contents have been examined. Maximum hexavalent chromium generation was observed in the temperature range around 773 K, at which most of the crystallization water decomposed from the sludge. When the heating temperature became higher than 1173 K, the amount of the hexavalent chromium extracted from the calcined sludge became as low as 10 mg/kg sludge. When the sludge was heated with iron oxides, FeO or Fe203, iron ferrite has been synthesized which may be used as a magnetic material. The amounts of hexavalent chromium generated in the heat treatment with iron oxides were not much different from those without iron oxides.

Jan 1, 2003

By Gus Van Weert

Hydrometallurgical oxidation of sulphides is capital and energy intensive, with autoclave and bio-technology competing for lowest overall cost status. The use of surface aerators instead of stirred tank reactors could provide lower costs for bio-oxidation of concentrates. With this in mind, the Delft Inclined Plate reactor was designed with inclined plates above a settler shaped reactor to continuously return slurry from the lowest point in the settler to the surface of the liquid. The multiplate superstructure overcomes the scale-up restriction of the standard circular surface aeration patterns. DIP aerator energy and volume requirements for oxygen transfer from air will be presented in terms of kg O2/kWh and kg O2/m3/h transferred as a function of wt % sand in the slurry and compared to stirred tank performance. Scale up from the 4 m3 pilot unit will be discussed.

Jan 1, 1996

By Ann M. Hagni

"Ceramic matrix composites are inorganic materials that are particularly resistant to heat and abrasion. A magnesia (MgO) and aluminum nitride (AlN) based composite is formed by exposing a magnesia preform to a metallic alloy block in a nitrogen atmosphere at 950°C. The metallic alloy, which is composed primarily of aluminum, is wicked into the preform. Aluminum nitride matrix is grown between MgO particles as the wicked metallic aluminum reacts with nitrogen. Unused metallic alloy, remnant metallic alloy (carcass), and composite produced after 8 hours, 50 hours, and 225 hours of processing are characterized mineralogically. Reflected light microscopy, transmitted light microscopy, scanning electron microscopy, energy dispersive spectroscopy, and X-ray diffraction techniques reveal that in addition to anhedral to euhedral AhNi, AbSbSr, and Al crystallizing in the metallic alloy carcass, AIN and (Al,Si)N have formed as well. Nitride rings and nodules in the carcass may hinder AIN growth in the composite. Fine-grained residual AhNi and AhShSr are dispersed throughout the composite matrix. The nitride matrix is composed of AIN and (Al,Si)N. Rim replacement of MgO by spine! occurs in the composite. Aluminum nitrides in the metallic carcass cathodoluminesce deep violet-blue, unlike non-luminescent AIN in the composite matrix. This distinction in cathodoluminescence suggests a different mode of formation for composite AIN than for carcass AIN. Phase interpretations and textural characterizations deduced from the implementation of sophisticated mineralogical techniques have contributed to the understanding, and will aid in the improvement, of MgO/ AlN-based ceramic matrix compositeprocessing."

Jan 1, 1999

By A. Onozaki

The Iijima Refinery was put into operation in 1972 and today has an annual production capacity of 156,000 tons of SHG electrolytic zinc. At the Iijima Refinery, the recoveries of gold and silver are 98.0% and 98.2%, respectively. Gold contained originally in the zinc concentrates reports in the Cu-Pb-Ag residue produced in the residue treatment process. Silver contained in the concentrates is distributed between the Cu-Pb~Ag residue and the copper cake produced in the purification process. The Cu-Pb-Ag residue, which contains gold and silver, is sent to the Oyachi flotatfon plant of the Kosaka Smelter; about 82% of the gold and about 85% of the silver are recovered in the copper flotation concentrate.. In this paper, the distribution of gold and silver in the Iijima. Refinery is discussed and operational results of the Oyachi flotation plant are presented.

Jan 1, 1990

By Antti Roine

Sulfidic zinc concentrates are usually roasted in a fluidized bed furnace into sulfur-free oxide form. Metallic zinc is produced from this oxidic calcine using hydrometallurgical leaching, solution purification and electrowinning stages. The roasting step is necessary because zinc oxides are easier to dissolve using traditional leaching methods than zinc sulfides. The Kokkola Zinc smelter uses various types of zinc concentrates and secondary materials as feed mixture. This makes it difficult to find optimum process parameters for the roaster when the composition and particle size distribution of the feed mixture varies even on a daily basis. Certain conditions may even cause difficult accretion problems or increase the amount of calcine in the process off-gas line excessively. A thermochemical heat and material balance model was developed for process advisor, in order to estimate the effects of different process parameters (temperature, process air coefficient, concentrate feed, oxygen enrichment, water feed, etc.) on the heat balance, roasting temperature and calcine composition. This model was constructed using the heat balance module of HSC Chemistry 4.0 software. The prevailing chemical compounds in the concentrate and calcine were verified using mineralogical analyses and equilibrium calculations. The roasting process seems to operate near chemical equilibrium conditions, if the behavior of the main components is considered. This paper describes briefly the basic principles of the calculation model and outlines the results with several diagrams and discussion. The calculated results were in reasonable agreement with the recent process air oxygen enrichment and water feed test campaigns carried out at Kokkola in 1999.

Jan 1, 2000

By Tianming Sun, Gabriella Tranell, Ragnhild E. Aune, Mark William Kennedy

Rare Earth Elements (REEs) are critical for the production of many advanced materials and products. Mining and primary production of REEs are generally associated with significant environmental impacts. By recovery of REEs from secondary sources, through recycling or as a byproduct, the adverse environmental impacts may be partly avoided. In the present study apatite concentrate originating from iron ore beneficiation done by LKAB in Kiruna, Sweden, is explored as a possible source for REEs. The composition and distribution of the REEs within the concentrates are studied using ICP-MS, XRD and SEM-EDS/EPMA, as well as the melting point and heat of fusion using DTA-TGA-MS. The behavior of the material during melting has also been studied through wetting and slag saturation experiments. The overall aim of the study is to evaluate the implications for future smelting experiments aimed at concentration and recovery of the REEs.

Jan 1, 2015

By T. Mutoh

Tellurium in raw slime has recently been recovered as copper telluride in Onahama Smelter & Refinery. The slime is decopperized with sulfuric acid solution in conventional leaching tanks. The pregnant leach solution containing 45 g/l of copper and 1 g/l of tellurium is introduced to a copper telluride recovering reactor. The tail solution from the reactor containing less than 20 mg/l of tellurium is recycled directly to circulation tanks of copper electrolysis. The impurities of the product copper telluride is kept below 1% without any purification.

Jan 1, 1990

By Petrus Christiaan Pistorius, Farzin Fatollahi-Fard

The production of titanium oxycarbide – a consumable anode material used in molten-salt processes for electrowinning titanium – from heavy mineral concentrate, such as a high-titania leucoxene and natural rutile is described. The oxycarbide is prepared by carbothermic reduction of the oxide at elevated temperature. Particle size distribution (of the titanium oxide raw material) and temperature have large effects on the kinetics of the reaction, which seem to follow a “shrinking-core” model. It is anticipated that low porosity (in the anode pellets) would be advantageous during electrolysis. Particle size distribution, extent of reaction during carbothermic reduction, and sintering temperature are expected to affect pellet porosity after sintering, and are being tested experimentally.

Jan 1, 2015

By Beate Ina Jenssen

Ferric iron removal from the nickel electrolyte at Glencore Nikkelverk AS in Kristiansand, Norway, is achieved by precipitation of iron hydroxide followed by filtration, and it is desirable to improve filtration properties of the precipitated iron hydroxide in order to decrease the filtration time. The effect of increasing the residence time from the current 45 min to 75 min and temperature from 65 °C to 90 °C on the filtration properties of the precipitated iron hydroxide (akaganéite) was studied by simulating the industrial process conditions in a continuous reactor setup operating at steady state, using ferrous-containing process solution as feed material. It was possible to decrease the filter cake resistance by both increasing residence time and temperature, but temperature gave the most pronounced effect and reduced the filter cake resistance by one order of magnitude.

By A. González

Arsenic is one of the main contaminants present in Chilean copper concentrates and its abatement represents a challenge for the process metallurgy, particularly under the strong environmental requirements in the global community. The possibility to form ferric arsenate directly from a gas phase by means of a heterogeneous reaction between an arsenic gas bearing and iron oxide was studied at laboratory scale. A thermodynamical analysis for the system Fe-As-O-S has been initially made, in order to obtain the stability conditions for the ferric arsenate or other FeAsyO2 type compounds. Experiments were made using an hematite sample suspended in a thermogravimetric device. AS4O6 gas generated from solid AS2O3 that was passed through the iron oxide sample and its instantaneous weight change was recorded directly. A kinetic study for the AS4O6 volatilization was made to control the gas composition. A chemical control between 300 and 600°C with an apparent activation energy of around 14 Kcal/mol As2O3 was determined. The samples after the reactions were chemically and XRD analysed. Arsenates detected corresponds to complex compounds. Results shows a dependence on temperature and oxygen content in the gas phase. The kinetics for iron arsenates formation is slow, reaching an arsenic capture of 6% after 80 minutes of reaction when an oxygen content of 50% is fed continuously at 800°C and 3,56% As in the gas. Experiences made at the same temperature but under higher oxygen content in a closed reactor, allowed arsenic capture close to 60%. For higher temperatures the capture is considerably lower.

Jan 1, 2003

By M. Furuta, M. Hasimoto, Y. Komoda, K. Haiki

"Tamano Smelter & Refinery started its operation in 1972 with high current density electrolysis (350Nm2 of maximum) applying PRC technology. After the start up, four times of expansion have been done, the cathode production capacity has increased from- 84,000 t/y to 191,000 t/y. However, recent refining technology with permanent stainless steel cathode enabled to increase current density up to 300 Nm2 or more without PRC method. In order to increase current density more than 350 A/m2 , experimental work using commercial size cell has been carried out at several conditions, such as current density, PRC conditions, electrolyte composition and electrode condition. As a result, it was found that high quality (LME A grade) cathode can be produced at such a high current density as 405 A/m2•IntroductionWhen considering the production increase of electrolytic copper, what becomes important is the improvement of productivity per unit of production facility. Conventionally, production had been expanded by increasing the number of cells but a huge investment required for this had a influence to the business profitability. Because of this, increase of current density, which is one of the methods to improve unit productivity, 'was expected and this method at the same time has another advantage of shortening the retention time of copper and other precious metals in the cells. At present, the average current density at Tamano during full capacity production is around 350 A/m2 and this used to be the limit throughout the world (1)."

Jan 1, 2000