Search Documents

By Kewal K. Kohli, Stefanie Self

"Three cases of surface subsidence investigated over abandoned coal mines after flooding in one case and dcwatering in two cases are presented in this paper. Mining was conducted by the room and- pillar method at all the mines leaving stable pillars. This paper will discuss the background chain of events and the likely causes of the pillar failure resulting in surface subsidence.CASE NO.1BackgroundThe Pittsburgh scam was mined in 1960 by the room-and- pillar method, leaving pillars (Figure I) through Mine A. located in Monongalia County. West Virginia.The mining height in U1is area was 1.83 m (6 ft) with an average mining depth of 140 m (460 ft). The mining recovery was 62% and the safety factor of the pillars was calculated at 1.15 using the Bieniawski ( 1984) fom1ula. For stable pillar design. a 1.5 safety factor is recommended. A 1.15 safety factor is considered marginal. Pumping continued after the mine was shut down in 1960 to prevent water seeping into an adjoining mine owned by the same company. The pumping ceased on December 12. 2003, and the mine was allowed to flood. The water level rose about 17 m (55 ft) by August 3 1, 2004, based on observations in a nearby borehole. On September 3, 2004 surface subsidence occurred above this area causing damage 10 a residence (Figure 2).Summary of InvestigationThe floor of the Pittsburgh coal scam played a strong role in the pillar failure. In this area, the immediate floor of the Pittsburgh seam consists of about two feet of fireclay. Extensive damage to the surface house was an indication that a major collapse below the surface had occurred. The pillars supporting the overlying strata were evaluated to find the cause of their failure. The pillars in the Pittsburgh seam (sec Figure I) had a marginal safety factor of 1.15 before flooding and were stable for 26 years. Once the mine was flooded the water level in the Pittsburgh seam rose by 17 m (55 ft). Shortly thereafter the fireclay in the floor weakened, resulting in several pillars punching into the floor unevenly making the immediate roof unstable. The overburden strata supported by these pillars also subsided do"" n into the mine, causing damage to several house on the surface."

Jan 1, 2010

By Pinnaduwa H. S. W. Kulatilake, Biao Shu

The intact rock properties and discontinuity properties for both Devonian Rodeo Creek (DRC) and Devonian Papovich (DP) rock formations that exist in the selected open-pit mine were determined from tests conducted on rock samples. Special survey equipment, which has a total station, laser scanner and a camera, was used to perform remote fracture mapping in the research area. From remote fracture mapping data, the fracture orientation, spacing and density were calculated using more refined procedures compared to what exist in the literature. Discontinuity orientation distributions obtained through remote fracture mapping agreed very well with the results of manual fracture mapping conducted by the mining company. The GSI rock quality system and Hoek-Brown failure criteria were used to estimate the rock mass properties combining the fracture mapping results with laboratory test results of intact rock samples. Fault properties and the DRC-DP contact properties were estimated based on the laboratory discontinuity test results. A geological model was built in a 3DEC model including all the major faults, DRC-DP contact and two stages of rock excavation. The built major discontinuity system of 44 faults in 3DEC with their real orientations, locations and three-dimensional extensions were validated successfully using the fault geometry data provided by the mining company using seven cross-sections. Numerical modeling was conducted to study the effect of boundary conditions and lateral stress ratio on the stability of the considered rock slope. For the considered section of the rock slope, the displacements obtained through stress boundary conditions seemed more realistic than those obtained through zero velocity boundary conditions (on all four lateral faces). Stable deformation distributions were obtained for k0 in the range of 0.4 to 0.7. Because the studied rock mass is quite stable, it seems that an appropriate range for k0 for this rock mass is between 0.4 and 0.7. The displacements occurred between July 2011 and July 2012 due to the nearby rock mass excavation that took place during the same period; they were compared between the field monitoring results available from the mining company and the predicted numerical modeling results and a good agreement was obtained. Overall, the successful simulation of the rock excavation during a certain time period indicated the possibility of using the procedure developed in this study to investigate rock slope stability with respect to expected future rock excavations in mine planning.

Jan 1, 2015

By Christopher Mark

Colombia is 11th largest coal producing nation in the world, and the world?s fifth largest coal exporter. But while most of Colombia?s coal is mined at large modern surface mines located near the Caribbean coast, there are also underground mines that produce high-grade metallurgical coal. These mines employ traditional hand-loading techniques in a variety of geologic environments, and they have some of the highest accident rates of any Colombian industry. The National Institute for Occupational Safety and Health (NIOSH) has been collaborating with POSITIVA, the primary provider of worker?s compensation insurance to the Colombian underground coal industry, to reduce the economic and social cost of rock falls in these mines. The specific goals of the collaboration are to 1) document practices and conditions in Colombian underground coal mines, 2) identify relevant international best practices, and 3) provide recommendations for developing a national campaign to reduce fatalities and injuries associated with roof falls. NIOSH conducted a survey of seven underground coal mines in four separate coalfields. Five of the mines were characterized by steep dips and weak roof and floor rock. The coal was loaded by hand at all seven mines, though two employed partially mechanized longwall techniques. Wood posts were by far the most common ground support. Roof bolts were not observed in use at any of the mines, and they are unlikely to replace timbers any time soon. While long-term entries generally appeared to be adequately supported, the survey found that less attention was paid to the temporary support that is installed right after the coal is removed. This temporary support is critical for protecting the workers from rock falls, however, because with hand-loading mining methods most of the activity takes place between the permanent supports and face. The study concluded that improving the temporary support in the working faces would be the most effective way to reduce the number of rock fall injuries. The key principle should be that every worker is protected by planned roof support at all times. Ground Support Management Plans, consisting of specific rules about when, where, and what roof support is to be installed, should be the focus of the campaign. Each Plan should be tailored to a specific mine based on the geologic conditions and mining methods in use. The Plan provides miners with clear, simple rules that can be easily understood, while management can easily check to see if it is being followed. Ground Support Management Plans will also provide the campaign with a concrete focus for the necessary cultural change.

Jan 1, 2014

By Tulu B. Ihsan, Mark A. Van Dyke, Ted M. Klemetti

"How well do current modeling procedures calculate the rear abutment extent and loading? Does an improved understanding of the rear abutment extent warrant a change in standing support in bleeder entries? What is the optimal standing support for bleeder entries separated from the longwall startup room by a barrier pillar? To help answer these questions and to determine the current utilization of standing support in bleeder entries, four bleeder entries at varying distances from the startup room were instrumented, observed, and numerically modeled. This evaluation was intended to determine the rear abutment extent and magnitude at various locations to optimize standing support in these entries and those under similar conditions. This paper details observations made by NIOSH researchers in the bleeder entries of a deep cover longwall panel; specifically data collected from instrumented pumpable cribs, observations of the conditions of the entries, and numerical modeling of the bleeder entries during longwall extraction. The primary focus was on the extent and magnitude of the abutment loading experienced by the standing support. As expected, the instrumentation of the standing supports showed very little loading relative to the capacity of the standing supports—less than 25 tons load and 1 inch convergence. The observations of the conditions showed little to no change from before the longwall panel extraction began to when the panel was more than 50% extracted. In addition to the observation and instrumentation, numerical modeling was performed to evaluate the bleeder design. The Flac3D program was used to evaluate these four bleeder entries using previously defined modeling and input parameter estimation procedures. The results indicated only a minor increase in load during the extraction of the longwall panel. The model showed a much greater increase in stress due to the development of the gateroad and bleeder entries, with about 80% of the increase associated with development and 20% with longwall extraction. The Flac3D model showed very good correlation between expected gateroad loading during panel extraction and those expected based on previous studies. The front and side abutment extent modeled was very similar to observations from this and previous panels with similar conditions. The results of this study showed that the rear abutment stress experienced by this bleeder entry design was minimal. The convergence measured in these bleeder entries was small enough not to mandate any additional support beyond development even by U.S. or Australian standards. The pumpable crib load and convergence experienced depends on the geological setting, mining geometries, and timing. The farther away from the startup room, the lower the applied load and smaller the convergence in the entry if all else is held constant. Finally, the numerical modeling method used in this study was capable of replicating the expected and measured results near seam."

Jan 1, 2017

By Mark Van Dyke, Gamal Rashed, Khaled Mohamed, Timothy Barton, Morgan Sears

"The unconfined compressive strength (UCS) of coal is an important parameter that controls the stability of coal ribs in underground mines. Estimation of the UCS of coal units composing the rib is required for conducting the rib stability assessment technique. This technique requires conducting large numbers of conventional UCS tests in a laboratory, which are expensive and time consuming. The research work outlined in this paper examines the use of indirect strength estimation methods—the point load test (PLT) and the in-situ Schmidt hammer test (ISHT)—for evaluating the intact strength of coal. The conventional UCS test was conducted on 80 coal specimens from 10 different coal seams for eastern coals. For each coal seam, the PLT and the ISHT were compared with the UCS test results to establish a correlation between the strength indices from the PLT or ISHT and the UCS. Moreover, to simplify the estimation of the UCS, a correlation between the megascopic coal lithotype and UCS was established.INTRODUCTIONBased on Mine Safety and Health Administration (MSHA) reports, rib failures have resulted in 17 fatalities, representing 52% of the ground-fall fatalities in underground coal mines in the United States over the past decade (MSHA, 2018). In an attempt to control rib failures in underground coal mines, the National Institute for Occupational Safety and Health (NIOSH) is working on developing a coal rib stability rating technique to provide a quantitative means to characterize the stability of coal ribs and to provide guidelines for early selections of rib support. The unconfined compressive strength (UCS) of coal units composing the ribs is one of the key input parameters required to estimate coal rib stability. The UCS of coal is an important parameter that controls the resistance of coal ribs to fracturing and slabbing. Direct determination of the UCS is time-consuming and expensive. Moreover, the UCS may be limited to testing only the strong coal samples since the weak or highly cleated samples might not survive the transportation and the preparation process (cutting and grinding). Therefore, alternative methods have been tested to indirectly find the intact strength of coal, such as the point load test (PLT) and the in-situ Schmidt hammer test (ISHT). The acronym ISHT refers to Schmidt hammer tests that were conducted in-situ on coal pillar ribs, while the acronym SHT refers to tests that were conducted on small scale blocks of coal."

Jan 1, 2018

By Ashok Kumar, Rajendra Singh, Petr Waclawik

High-grade coal is locked in the shaft protective pillars at 900 m below surface in the Czech part of Upper Silesian Coal Basin. To optimise recovery of coal from the larger size shaft protective pillar, room and pillar (called bord and pillar in India) is trialled to further develop these on smaller pillars. This development followed a constant gallery width of 5.2 m and 3.5 m height. The monitored pillar size in the first developed panel varied from 860 m2 to 1225 m2 of area. The stability of these pillars (i.e., natural supports) at this depth of cover is observed to be a vital issue to control ground movement and safety of the surface structures. A simple calculation of safety factor revealed that application of an empirical method for estimating size and shape of the pillar is inappropriate due to complex geo-mining conditions of the site. Accordingly, geo-technical instruments are installed in the panel for monitoring the stability of the diamond shaped pillar at different stages of the development. Extensive monitoring of the pillar behaviour by these instruments provided an important set of data for such optimum recovery. An established process of simulation-based pillar strength estimation is often used by the mining industry, but calibration is generally done with the help of empirical formulation. However, for the deep-seated pillar, the strength suggested by the existing empirical formulations (except the CMRI formula) is found to be much different from the instrument observations. Using a study conducted at Czech hard coal mines, an attempt is made to develop a strain-softening-based numerical modelling approach to assess pillar performance at deeper cover. The recorded value and nature of the pillar spalling in the field along with the CMRI formula are used to calibrate the developed simulation approach. An assessment of the stability of the developed pillars using simulated models did not indicate any collapse of the natural supports. This paper briefly presents difficulties in pillar design at great depth of cover and field and simulation results of pillar strength estimation in Czech hard coal mines.

Jan 1, 2018

By Esterhuizen S. Gabriel, Su W. H. Daniel, Tulu B. Ihsan, Klemetti M. Ted, Mohammed M. Khaled, Gearhart F. Dave

"A numerical-model-based approach was recently developed for estimating the changes in both the horizontal and vertical loading conditions induced by an approaching longwall face. In this approach, a systematic procedure is used to estimate the model inputs. Shearing along the bedding planes is modeled with ubiquitous joint elements and interface elements. Coal is modeled with a newly developed coal mass model. The response of the gob is calibrated with back analysis of subsidence data and the results of previously published laboratory tests on rock fragments. The model results have been verified with the subsidence and stress data recently collected from a longwall mine in the eastern United States. INTRODUCTION In 2015, there were 40 longwall mines operating in the United States, each producing an average of 4.5 million tons of coal per year, and they supplied 60% of the U.S. underground coal production. This represents a substantial increase from 50% three years earlier (Sears, Tulu, and Esterhuizen, 2017). During this period, reportable roof fall rates in U.S. longwall mines also increased. Large roof falls that can block the gateroads are not only a ground-fall hazard, they can disrupt the ventilation system, block the escapeways, and increase the potential for elevated methane levels in the gob. To address these hazards, the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) is conducting research to improve the design of ground control systems in longwall gateroads. Gateroad stability is primarily determined by the longwall pillar design. Generally, the required dimensions of the pillars around a longwall panel are determined first, which then dictates the location of the gate entries relative to the mined panel. The Analysis of Longwall Pillar Stability (ALPS) method is the most accepted gateroad pillar design procedure in the United States (Mark, 1992). The ALPS method accounts for local roof geology in the gateroad stability assessment by including the Coal Mine Roof Rating as an input parameter (Mark, 1992). The key assumption in the ALPS method is that unstable pillars result in unstable gate entries. However, experience provides examples of mines where pillar stability and gateroad stability are only loosely correlated (Su, Draskovich, and Thomas, 2003)."

Jan 1, 2017

By Pinnaduwa H. S. W. Kulatilake

To exploit an underground mine effectively and safely, it is important to have a good understanding of the geotechnical behavior of the rockmass surrounding the underground mine excavation. The aim of this study was to investigate, at the threedimensional level, the geotechnical behavior around a tunnel excavated in a metal mine in China. A three-dimensional numerical model was built by using the 3DEC software package to simulate a tunnel excavation under a high in situ stress condition and by relying on the information available on lithology, geological structures, in situ stress measurements, physical and mechanical properties of intact rock, discontinuities, and interfaces between different rocks. The authors also investigated the effect of the discontinuity network, possible intact rock and discontinuity parameter variability, representation of rock masses as discontinuum or equivalent continuum material and rock support system on the deformation, and stability around the tunnel. A very good agreement was obtained between the collected field deformation monitoring results and the results of the conducted numerical stress analyses with appropriate geomechanical property values.

Jan 1, 2013

By Douglas Tesarik, Mark K. Larson, Habte Abraham, Heather E. Lawson

Dynamic failures, or "bumps", remain an imperative safety concern in underground coal mining, despite significant advancements in engineering controls. While many factors have been empirically linked to the occurrence of dynamic failure events, identifying a consistent, repeatable set of criteria within a field setting has proven elusive; conditions generally associated with dynamic failure might produce an event at one site, but not another. Conversely and more troubling, dynamic failure could occur where relatively few of these factors exist. The presence of spatially discrete, stiff roof units, such as paleo channels, are one such feature that has been linked to the occurrence of dynamic failure events. However, an empirical stratigraphic review investigating the relative frequency of discrete units in bumping versus non-bumping deposits indicates that no significant difference exists based on this criterion alone, and that instead an apparent relationship exists between reportable bump history and the overall character of the host rock with respect to stiffness. Due to the complexity of the bump problem, however, these results are not conclusive, as they do not take into account any variable other than the presence or absence of stiff members in the roof lithology; To weight the relative impact of changes in a single variable, such as the thickness or location of sandstone members, it must be examined in isolation-i.e. in a setting where all other variables are held constant. Numerical modelling provides this setting, and the effects of variability in a stiff discrete member in a hypothetical longwall mining scenario are investigated within the context of three stratigraphic "types'', as determined by the ratio of stiff to compliant stratigraphic members; Compliant, Intermediate and Stiff A modelling experiment examines changes in rupture potential in stiff roof units for each stratigraphic type as discrete unit thickness and location are manipulated through a range of values. Results suggest that the stiff-to-compliant ratio of the host rock has an impact on the relative stress-inducing effects of discrete stiff members. In other words, it is necessary to consider both the thickness and the distance to the seam, within the context of the host rock, to accurately anticipate areas of elevated rupture induced hazard; acknowledging the presence of a discrete unit within the overburden in general terms is an insufficient indicator of risk. Through modelling of anticipated changes in the placement and dimensions of discrete units within their stratigraphic setting, elevated rupture-induced bump hazard can be anticipated on a case by case basis. Were similar modelling studies conducted at mine sites in tandem with tracking of problematic discrete stiff units, areas of elevated rupture risk could be anticipated in advance of mining. Developing this predictive capability beyond identifying rupture potential in discrete roof members is essential to the eventual elimination of dynamic failure related worker injuries and fatalities. As stress is a necessary component in the occurrence of dynamic failure events, this finding helps to refine our understanding of the role of individual stiff, strong roof members in bumping phenomena, and suggests that a more holistic view of overburden lithology, combined with site-specific numerical modelling, may be necessary to achieve greater miner safety.

Jan 1, 2016

By Michael Murphy, Khaled M. Mohamed, Berk Tulu

"Failures of coal ribs are major hazards in underground coal mines. For the period of 2010 to 2014, rib falls were the leading cause of groundfall fatalities and accounted for 35% of all groundfall-related fatalities. Currently, the National Institute for Occupational Safety and Health (NIOSH) is conducting a research project to develop an engineering-based design methodology for rib control in underground coal mines to reduce rib fall accidents and fatalities. Numerical models can be used as part of the design methodology provided the models are appropriately calibrated and verified.This paper presents a coal rib model to simulate the mechanism of coal deformation and fracturing that can lead to stress-driven rib falls. The proposed coal rib model was calibrated against published data from an instrumented rib site at the West Cliff Mine in Australia. Fracturing of the coal rib was defined by critical VALUES (of plastic shear strain of the coal material and rib displacement. A critical plastic shear strain of 2.8% and a sudden increase of rib displacement of 30 to 45 mm were sufficient to develop a fracture plane in the rib model. Accordingly, a discontinuous rib deformation was achieved and it compared favorably against field monitoring data.INTRODUCTIONCoal ribs are the vertical walls of coal formed when entries are developed in a coal bed. Failures of coal ribs are a major hazard in underground coal mines. Furthermore, failing ribs can contribute indirectly to roof and floor instability by increasing opening widths across intersections and entryways. Over the last 18 years, there has been a continual occurrence of injuries and fatalities in underground coal mines due to rib falls. For the period of 2010 to 2014, rib falls (excluding longwall face failure and bursts) were the leading cause of ground fall fatalities and accounted for 35% of all groundfall-related fatalities (MSHA, 2015)."

Jan 1, 2016

By Bob J. MacDonald

The Cape Breton Development Corporation is a federally owned Crown corporation in Canada that operates two coal mines the Prince and Phalen Colliery in the Province of Nova Scotia. Retreat longwall mining was first introduced to the shallower workings (I 80m) of Prince Colliery in the early 1980's. Phalen Colliery started longwall retreating in 1987 and since that time has extracted twelve panels. In 1993 there had been a total of eight longwalls varying in widths from 140-230m mined in Phalen Colliery that is on the Phalen Seam. Up to this point there were only minor ground control problems on the faces except for one of the earlier longwalls that was mining a split seam. There is some interaction on Phalen workings from remnant structures in the overlying Lingan and No. 26 Collieries which worked the Harbour Seam. Induced abutments loads along pillar edges have been observed and resulted in poor face conditions when mining the Phalen Seam. The ninth panel, 6 East was the first panel to suffer a major roof fall from the First Major Weighting. This was also the first panel to undermine a paleo sandstone river channel named the Lower Sandstone Unit (LSU). For the first time in Phalen's history subsequent longwalls began to experience periodic weighting events. The 6 East panel suffered a number of periodic weightings and on two occasions had to use foam cement to fill the cavities that resulted. On the next east side panel, 7 East, there were numerous periodic weighting events, but interestingly there was no significant First Major Weighting. 7 East was the first 260m wide panel and all others were 230m or less. This longwall was 3,400m long and began producing in December of 1994 and was still cutting coal in May of 1997. There were five significant roof fall events on this panel, three of which required foam cement to fill the cavities. Of these three the interruption to production varied from four days to seven months. There were definite precursors to each of the weightings including: 1) an increase in audible noise (termed bumping) on the face, 2) supports went rapidly into yield, 3) roof convergence increased, 4) water percolated from the face roof strata, and 5) severe spalling of the coal occurred resulting in increased tip to face distance. Longwall face weightings are a result of geomechanical factors and cannot be avoided However, the loss of roof control is a different matter and highly subjective to operational procedures. The causes of weightings, their magnitude and impact on the mining at Phalen have been investigated. The following factors have been identified as relevant to these occurrences. 1. The influence of pillars in the overlying Harbour Seam workings. 2. Location of the LSU relative to the Phalen Seam. 3. Thickness of the LSU. 4. Pressure arch effect from the adjacent gobs. 5. Poor operational practices on the longwall including: a) slow rate of retreat; b) inadequate supply of pump pressure to the hydraulic supports; c) premature yielding of the yield valves; and d) poor face alignment practices. This paper will review the events that took place on the 7 East longwall and show that the Lower Sandstone Unit is the primary cause of the weightings. However, other factors contributed to the loss of roof control and the formation of the roof cavities.

Jan 1, 1997

By Robert J. Coutts, Dan A. Payne

"The Broadmeadow mine is a punch longwall mine owned and operated by BHP Billiton Mitsubishi Alliance (BMA) in the Bowen Basin of Queensland, Australia. In 1999, an exploratory adit was driven as part of the feasibility study for the establishment of the mine. Subsequent development of the mine in 2004 started some distance away from the initial test adit. Ten years later, the trial adit would be used as the headgate of the 5'h longwall panel. However, multiple roof falls had occurred in a heavily jointed area over a distance of 1, 000 ft (300 m) during the past 10 years. Due to the immediate coal roof, low stress environment and time, some of these falls had progressed to 38 ft (11.5 m) above the mining floor. As a result of the extensive work involved and safety implications of trying to recover the roof falls conventionally, a strategy was developed to fill these roof falls with a cement based product from the surface, down boreholes, and redrive the roadways through the consolidated roof fall material. This paper describes the process of rehabilitating these roadways, the results when the roadway was redriven and the headgate performance as the longwall mined through the area.INTRODUCTIONBMA operates 7 open cut and 2 underground mines in the Bowen Basin of Queensland, Australia producing over 50 mt per year of high quality coking coal. As a result, BMA has established over 150 miles (250 km) of open cut highwall.Broadmeadow Mine is a punch longwall mine located 22 miles (35 km) north of Moranbah in Queensland, Australia on the western limb of the Bowen Basin Coal Measures (Figure 1). Broadmeadow Mine commenced development in 2004 and began longwall operations in 2005. Broadmeadow is currently completing the fifth longwall panel and produces over 4 Mt per year of high quality coking coal. Mining is undertaken in the Goonyella Middle Seam, which is 21 to 25 ft (6.5 to 7.5 m) thick in the current mining area.The mine layout required the use of an old exploratory gateroad as the headgate of its 5th longwall. This gateroad had experienced numerous large roof falls and required extensive rehabilitation."

Jan 1, 2010

By Martin McKinnon, Guy Reed, Russell Frith

"It is arguable that the development of reinforcing roof bolting systems has largely stagnated in recent times, primarily due to the prevailing industry view that few, if any, further improvements can be made to what currently exists. However, this paper contends that reinforcing roof bolting systems can be further refined by considering both the specific manner by which horizontally bedded roof strata loses its natural self-supporting ability and the specific means by which reinforcing roof bolts act to promote or retain this natural self-supporting ability. The Australian coal industry insists on minimising bolt-hole diameter to maximise load transfer and on targeting full-encapsulation by any means necessary. This has led to a significant, albeit unintended, consequence in terms of overall roof bolting effectiveness, namely increased resin pressures during bolt installation and the associated potential for opening bedding planes that may have, otherwise, remained closed during the bolt installation process. Given that the natural self-supporting ability of roof strata is strongly linked to whether bedding planes are open or closed, logically, minimising resin pressures should be a significant benefit. This paper focuses primarily on three key issues that relate directly to the function of the roof bolting system itself: (i) the importance of proper resin mixing in the context of maximising load transfer strength and stiffness, (ii) the importance of minimising resin pressures developed during bolt installation, and (iii) the importance of maximising the effectiveness of the available bolt pre-tension. All mine operators should be invested in improving the individual effectiveness of each installed roof bolt, even by relatively small incremental amounts, so this is an important topic for discussion within the mining community."

Jan 1, 2017

By Eric C. Poeck, Ryan Garvey, Ugur Ozbay, Kun Zhang

"A coal bump is characterized by the sudden failure of one or more pillars and an associated release of kinetic energy. Although the geologic conditions surrounding coal bumps are often similar, their occurrence and magnitude are difficult to predict. This paper presents the development of an approach to assess the potential for coal bumps in room and pillar mines through the use of energy concepts and special consideration of the interface properties between the coal and overlying rock. Back analyses were performed on the widespread collapse of a room and pillar mine with an associated 3.9 local magnitude seismic event. Pillar and mine-scale models were constructed using the distinct element method to simulate the mining stages leading up to the collapse. A variety of loading conditions, material properties, and interface properties were evaluated for their effect on unstable failure of single pillars, and the mine-scale model was used to study the evolution of failure during progressive mining. The extent of unstable failure was quantified in these models by calculating the total kinetic energy released during each mining stage. Through the parametric analysis of single pillar models, it was found that softening parameters in either the coal or the coal/ rock interface can individually facilitate unstable failure of pillars, but the combination of the two in a single model produced a much higher release of energy during failure. The results of the minescale model further illustrated the trend as the combination of softening parameters in the coal and coal/rock interface produced a series of failures that most accurately reflected the collapse event at the mine. The method of room and pillar stability analysis demonstrated in this study effectively explores the potential for large coal bumps.IntroductionThe analysis of coal pillar behavior is challenging because natural variability in geologic conditions requires estimation of material strengths and predicted loads for a given mining situation. Large width-to-height (w/h) ratio pillars and deep overburden present an additional challenge, as the failure behavior of such pillars is more complex and may involve unstable, sudden collapse. Empirical methods have improved the success of coal pillar design for a wide range of conditions, but, for deep cover and squat pillar (w/h > 10) geometries, pillar performance predictions are not as accurate (Mark, 2000). As with any empirical approach, more back analysis and the consideration of new variables may help improve understanding and accuracy of future designs."

Jan 1, 2015

By Kun Li, Shuaishua Yue, Huigui Li, Yuan Ruifu, Yongxiang Xu, Huamin Li

"Coal seams in Tashan Mine of Datong Coal Group in China average 49.2 ft (15m) thick and have been mined by the top coal caving longwall mining method of large mining height. Mining height was 12.5 ft (3.8m) and the top coal caving height was 36.7 ft (11.2m). The gateroad pillar between panels was 124.6 ft (38m). During retreat mining, serious bumps occurred in the gateroads on both sides of the pillar affecting safety production. Therefore, pillarless mining was experimented.Using numerical modeling and comparative study of cases of similar mining condition, it was decided to employ a 19.7 ft (6m) wide pillar, rather than the previous 124.6 ft (38m) wide pillar. Support system for the gateroads was designed and implemented. During gateroad development, pillar failure conditions and entry deformation were monitored. Hydraulic fracturing method was employed to cut off the K3 sandstone along the entry rib so as to reduce the abutment pressure induced during retreat mining. Support reinforcement method combining grouting and advanced reinforcement methods was proposed to insure stable gateroad ahead of mining. Methane drainage and nitrogen injection were implemented to eliminate hazards associated with mine fire and spontaneous combustion.Since the development of gateroad has just completed, and retreat mining has not begun, the effectiveness of the proposed methods is unknown at this point. However, monitoring will continue until after mining. The results will be published in a separate paper.INTRODUCTIONGeneral descriptionTashan mine is located about 15 Km south of the city of Datong, Shanxi province, China (aure 1). The 2014 raw coal production was 25 million mt."

Jan 1, 2015

By Karsten Zimmermann, Peter Cain

"To receive regulatory approval for a new coal mining operation in North America, extensive investigations of feasibility and potential environmental impacts, including ground deformations, are required. Figure 1 shows pictures from mine sites and an example mine map with the planned panel layout for one seam of the multi-seam longwall operation considered.The cumulative mined coal thickness of 22 meters in some areas of the operation requires a comprehensive forecast of expected ground movements and subsidence impacts (e.g., subsidence, slope, displacement, curvature and strain). In the frame of the impact study, the prediction of these impact factors was conducted by DMT using the computer program SPS 4D, based on the Ruhrkohle modeling method by Ehrhardt and Sauer (1961).This paper briefly presents the modeling method and explains the benefits and possibilities for its international application. Information gathered from literature studies on subsidence in North America were incorporated into the initial model parameterization. The article shows the ways in which the observed influences of mountainous topography on surface displacements and deformations can be considered by an extension of the subsidence prediction model and integration of DEM information.SUBSIDENCE MODELFor the calculation of mining-induced subsidence and deformation, DMT has developed subsidence prediction software SPS 4D, which is built according to the stochastic prediction model by (Ehrhardt and Sauer, 1961). The model is based on the subsidence theory by (Knothe, 1953) with a specific parametrization of the stochastic influence function and includes enhancements for dynamic subsidence calculations after (Sroka, 1978). In Europe, mainly in Germany and Poland, the model is approved by the authorities as a standard model for subsidence prediction in mining areas. However, extensive research within R&D activities has shown the possibility to predict mining-induced subsidence considering the specific mining conditions in North America (Zimmermann and Fritschen, 2007)."

Jan 1, 2016

By David R. Burkhard

"Comparative roof beam performance, as measured by delamination within the bolted horizon, was used to evaluate two types of roof bolt drill hole geometries in a development setting. Short encapsulation pull tests had demonstrated a higher grip factor in drill holes featuring helical grooves in the side walls in comparison to drill holes featuring continuous smooth to slightly rough walls. The study incorporated the two geometries during development mining in which fully grouted mechanically anchored bolts were installed as primary roof support.bolts were installed as primary roof support.The study site, in an entry adjacent to a longwall panel, was instrumented with extensometers and data collected during longwall retreat. Statistical analysis was conducted to validate null and alternative hypotheses used to compare drill hole geometries. Analysis yielded no statistically significant difference between drill hole geometries. Inspection of the data does reveal less delamination within the smooth walled site in comparison to the site containing grooved hole geometry.INTRODUCTIONFrom their introduction as a means of ground control over sixty years ago, roof bolts today are the primary mechanism of roof support utilized throughout mining. Whether through suspension, keying, or beam building, roof bolts are employed to reinforce the inherent strength of the strata comprising the immediate roof with the goal of creating a competent bolted horizon of sufficient load bearing capacity to be self-supporting for a given mine's design life, stress regime, and geomechanical properties.For grouted bolts in sedimentary strata, axial loading due to vertical rock movement and bending due to horizontal rock movement are the principal means of loading (Signer, 2000). Regardless of the type of bolt and extent of grouting employed, the success of any roof bolting design is determined, to a large extent, by the effectiveness of load transfer between the rock, grout, and bolt.At San Juan Mine, an underground longwall mine located in the northwestern corner of New Mexico, a number of different roof bolt types, grades, and lengths have been used over the years in an effort to optimize primary roof support. One common denominator shared throughout has been the use of full length grout. Load transfer for full length grout is achieved primarily through mechanical bonding between the grout and rock. It is this interaction that is the focus of the study described in this paper. The study assessed and compared two types of bolt hole geometries employed during gate road development at San Juan. Underground instrumentation and evaluation of the bolted roof provided the means of assessment and comparison."

Jan 1, 2016

By Juan J. Monsalve, Nino Ripepi, Richard Bishop, Jon Baggett

"Terrestrial laser scanning (TLS) is a useful technology for rock mass characterization. A laser scanner produces a massive point cloud of a scanned area, such as an exposed rock surface in an underground tunnel, with millimeter precision. The density of the point cloud depends on several parameters from both the TLS operational conditions and the specifications of the project, such as the resolution and the quality of the laser scan, the section of the tunnel, the distance between scanning stations, and the purpose of the scans. One purpose of the scan can be to characterize the rock mass and statistically analyze the discontinuities that compose it for further discontinuous modeling. In these instances, additional data processing and a detailed analysis should be performed on the point cloud to extract the parameters to define a discrete fracture network (DFN) for each discontinuity set. I-Site Studio is a point cloud processing software that allows users to edit and process laser scans. This software contains a set of geotechnical analysis tools that assist engineers during the structural mapping process, allowing for greater and more representative data regarding the structural information of the rock mass, which may be used for generating DFNs. This paper presents the procedures used during a laser scan for characterizing discontinuities in an underground limestone mine and the results of the scan as applied to the generation of DFNs for further discontinuous modeling.INTRODUCTIONAccording to the Mine Health and Safety Administration (MSHA), between 2006 and 2016, the underground stone mining industry had the highest fatality rate in 4 out of 10 years, compared to any other kind of mining (MSHA, 2016). Additionally, during that same time, 40% of the fatalities were due to ground control issues, such as roof and rib collapses and pillar bursts. The National Institute for Occupational Safety and Health (NIOSH) developed guidelines for designing underground stone mines (Esterhuizen, Dolinar, Ellenberger, and Prosser, 2011). However, these guidelines do not apply to all underground stone mines.Monsalve, Baggett, Bishop, and Ripepi (2018) present a case study of an underground limestone mine experiencing a structurally controlled mode of failure. The authors analyze different methods to study that type of instability. They conclude that the integration of terrestrial laser scanning (TLS) with discrete element modelling (DEM) can be used to prevent rock falls in underground excavations to enhance worker safety. However, an adequate rock mass characterization and structural mapping must be performed in order to generate reliable models that allow the engineer to have a better understanding of the rock mass behavior."

Jan 1, 2018

By Rajendra Singh

Considering the importance of a fully mechanized depillaring operation, the Indian coal mining industry has introduced a number of such depillaring operations at depths of cover ranging from 60 m to 377 m. The overlying strata of these depillaring faces vary widely from highly laminated, weak and easily caveable to massive, strong and difficult to cave. Most of these mechanized depillaring operations were carried out in difficult site conditions, however, performance monitoring in the field has showed good production, productivity and safety results. Field studies have shown that the use of roof bolts as breaker line support for this technology worked well for moderate strength overlying roof strata, but experienced difficulties for both extremely weak and strong/massive overlying roof strata. It is observed that the performance of a breaker line support along the goaf edge deteriorated with an increase in depth of cover of the depillaring face. Practice of a straight line of extraction (single row of pillars) during the mechanized depillaring below competent roof strata experienced a considerably large hanging area inside the goaf, which needs to be managed either by induced caving of the roof strata or through an increase in width of the excavation. Observations of good performance of a fully mechanized depillaring face under highly laminated and weak strata at a shallow cover is mainly due to a faster rate of extraction. However, the mechanized depillaring underneath laminated and weak roof strata for a deep-seated coal seam was forced to go for partial extraction mainly due to strata control problems. Discussing the implications of main technical and operational differences between the conventional (semi-mechanized) and fully mechanized depillaring, this paper presents results of different strata control studies conducted at different mechanized depillaring sites with varying geo-mining conditions.

Jan 1, 2014

By David F. Gearhart

A cooperative study was conducted between Signal Peak Energy and the National Institute for Occupational Safety and Health (NIOSH) to evaluate the behavior of a pre-driven recovery room under less than 200 ft of cover. The design of the support systems for a pre-driven recovery room must provide control of the roof and ribs during the changing stress environment experienced throughout the final advance of the longwall into the recovery room. It must also provide a stable area where mine personnel are not exposed to undue hazards during shield recovery operations. This recovery room was constructed in two phases; each phase mined a 21-ft-wide room that was heavily supported, and subsequently fully backfilled with 800-psi, cellular concrete. Instrumentation to monitor the recovery room performance included borehole pressure cells (BPCs) placed in the head gate and tailgate pillars, at four locations across the longwall panel, in the fill material, and in the first row of outby pillars near the center of the panel. Four roof-to-floor convergence sensors were installed in the back fill material and a vertical, multipoint borehole extensometer (MPBX) measured the displacement of the strata above the recovery room. Surface surveys were conducted to measure MPBX collar movement. The data show that the front abutment load was transferred onto the recovery room backfill and the out by pillars as the longwall panel was extracted. As the longwall approached the recovery area, the fender and shields yielded, but the backfill provided enough support to keep the room stable as the longwall advanced to its final position. The system worked as planned and the face was recovered in record time.

Jan 1, 2014