Search Documents

By R. Schuerch, C. Cimiotti, M. Piemontese, N. Karlin, P. Perazzelli, P. Halton

The new Los Angeles, California JWPCP effluent outfall tunnel will transport secondary-treated effluent from the Joint Water Pollution Control Plant in Carson to White Point Manifold. The tunnel will be approximately 7 miles (11 km) long with a finished internal diameter of 18 ft (5.5 m). The TBM is designed to cope with high water pressure up to 10 bar. The geotechnical challenges are due to the heterogeneous subsurface conditions: in the first half of the alignment, the tunnel runs through soils with a low overburden under urban areas, and, in the second half, the tunnel runs through extremely weak, intensely faulted rock masses with high overburden. Following an overview of the project, this paper focuses on the northern portion of the alignment and presents a decision-making procedure developed during pre-excavation phase in order to cope with the expected heterogeneous conditions during mining. The risk assessment and the TBM operational design of the southern portion will be dealt with in a future paper.

Jun 13, 2023

By Marcel Michaud

Over the past five years, the two-fold growth in Canada's coal industry "Figure, 1" results primarily from the coking coal market to Japan and, to a lesser degree, by the increasing use of sub-bituminous and lignite coal for power generation in the Prairie Provinces. This expansion will continue, but production of coal for domestic thermal generation of electricity will grow at a faster rate than coking coal exports "Figure, 2". Half of the 20 million tons of thermal coal used for electrical power generation in Canada during 1974 were imported by Ontario Hydro from U.S. coal companies in West Virginia and Pennsylvania. Ontario Hydro's Nanticoke station on Lake Erie which will consume 7.5 million tons of coal in 1977 when fully operative, as well as other future planned projects, could cause Ontario Hydro's coal consumption to rise from 10 million tons today to 20 to 25 million tons by 1985

Jan 1, 1975

By Christopher D. Henry

Environmental geologic maps of the Wilcox and Jackson-Yegua lignite belts of the Texas Coastal Plain delineate land areas on the basis of their natural characteristics. Criteria used to define map units include substrate, soil, topography, geologic process, vegetation, and land use. The maps are useful in planning and reclamation of lignite mines and in meeting the requirements of State and Federal surface mining laws. Specific applications include identification of land capability, recharge areas and geometry of aquifers, flood-prone areas, areas that may qualify for prime farmland status, and other areas sensitive to lignite mining.

Jan 1, 1982

By P. R. Taylor

A review of the advantages and disadvantages of plasma technology for metal and mineral wastes is presented. Examples of the use of plasma systems are given and possible future uses are outlined. Among the potential uses are treatment of electric arc furnace (EAF) dusts, the vitrification of nuclear wastes and the removal of toxic metals. Over the past few decades, plasma technology has been studied for potential applications over a wide range of metals/materials processing areas. One promising area of plasma technology applications is the treatment of industrial hazardous waste. The potential generation of hazardous and toxic waste by various industries has become a matter of public and political awareness. Environmental regulations have put stringent toxicity emission limits on disposable waste streams. An intensive research effort is currently underway in the area of hazardous waste treatment.

Jan 1, 1994

By Devan Naik, Matthew Stokes, Andy Nigro

This paper describes the surgical removal of a 24 ft dia. Slurry Shield TBM entombed beneath one of the country’s busiest commuter rail interlockings, the Harold Interlocking in Queens, NY, and the construction of the interface to a cut/cover tunnel which extended the mined tunnel section. A sophisticated SOE was built around the TBM to support active track loads within 8ft. of the excavation. Once the TBM head and guts were removed, a full round CIP lining was installed connecting the existing precast tunnel liner to the C/C tunnel under construction. All this construction was done on a narrow island of land without road access nestled between 7 mainline LIRR/Amtrak rail lines.

Jun 13, 2021

Approximately forty years ago, the military services began a realistic investigation of the problems involved with the replacement of high pressure gaseous systems with liquid oxygen systems. The program was temporarily discontinued because of numerous State-of-the-Art problems. Ten years later, interest in the liquid oxygen breathing concept was revived. Initial testing of this concept was completed in 1946. The ensuing years have seen the general acceptance of many cryogenic breathing systems for airborne applications. The inherent features of weight savings (approximately 70%) and space savings (approximately 80%) make it very desirable for high performance military aircraft. A typical aircraft system consists of a storage container with appropriate integrated control valving (the liquid oxygen converter), a heat exchanger, breathing regulator, and oxygen mask. Normally the liquid converter is located in the aircraft wheel well for easy access by ground crew personnel and the breathing regulator is mounted in the cockpit where the pilot can connect his oxygen mask. An aircraft system such as this will provide the pilot with eight hours of breathing oxygen after a 24 hour standby period. Early in 1960, the National Aeronautics and Space Administration sought a means of providing a cooling system for their personnel involved in fueling the rockets used in the space program. While fueling rockets N.A,S.A, personnel wore a completely enclosed butyl rubber suit and were susceptible to heat prostration. Using the concept of an aircraft system, Aro redesigned the container, heat

Jan 1, 1971

By B. Das, D. D. Mishra, M. I. Ansari

Experiments conducted with a 75-mm-diem hydroryclone have shown it is possible to obtain an iron ore concentrate containing 60% Fe. 2.65% SiO2, and 4.0% Al2O3 from Barsua iron-ore washing-plant slimes. About 60% of the iron values are recovered from slimes containing approximately 49% Fe, 8.9% A1203 and 11% SiO2. The obtained products can be used in the sinter feed for iron and steel making. The key to achieving process success lies in establishing the correct cut point (d50) of the hydrocyclone through the manipulation of operating and design variables, such as spigot and vortex finder diameter, solids concentration and operating pressure. The cyclone efficiency is represented by the partition curve. The cyclone performance, evaluated mathematically from the reduced efficiency curve, is represented by the equation Y = 100[1 -exp(-axb)], where: •X = did 50, •Y = corrected of efficiency (%) and •a and b are constants.

Jan 1, 1994

By A. P. Cook

Methane drainage on a mine-wide scale is a relatively new technology to South African coal mines. Shallow seams and apparently low methane contents have been assumed to result in less methane problems than experienced in other countries. The introduction of deeper mines however, has now resulted in methane drainage taking on a higher priority. Methane contents in the region of 12 m3\t have resulted in one colliery introducing drainage as a ventilation support. Although a low seam permeability initially indicated reduced potential for drainage, early borehole flows of 90 m3\m\year have since increased to 450 m3\m\year. Rapid inflow of methane into goafs and sealed areas from seams surrounding the main production seam at another colliery have warranted extensive evaluation of the methane properties of these seams with the projected introduction of predrainage from surface. Methane pressures in excess of 1000 kPa and contents in the region of 10 m3\t again give methane volumes suitable for drainage. Coal seam drainage ahead of mining is becoming more significant and is likely to see an increase in the near future. INTRODUCTION Methane gas is an everpresent hazard associated with underground coal mining. Safe working levels of methane in the mine atmosphere are normally maintained by ventilation practises, ensuring sufficient dilution of the gas. However in some cases the ventilation must be assisted by methane drainage, either from the mined seam, or from adjacent seams and strata, or from goafed areas. South African collieries have practised only limited methane drainage until now. Relatively shallow mining depths, and apparently low in-seam methane contents have been assumed to result in fewer problems with methane than are the normal for other countries. This is now being shown to not necessarily be the situation. Work carried out by the Coal Mining division of COMRO (Cook and Erwee, 1991) indicates South African production coal seams have very similar methane retention properties to those of coals in other countries, with seam gas contents of up to 12 m3/t. This awareness, as well as greater mining depths, and higher degrees of mechanisation, has resulted in higher priority being given to methane emission problems throughout the industry. Increased levels of safety, as well as possible commercial applications, are the main reasons for the interest now being shown in methane drainage. Not only is there possible applications in the present production coalfields, but South Africa has vast areas of coal reserves which are presently non-mineable, now being seen as possible alternative energy sources. Limited methane drainage is practised within the industry, but only on collieries that have identified specific methane problems that can be alleviated by drainage. Historically this has been restricted to surface drainage of longwall goafs, reducing emissions onto the faces. More recently, horizontal in-seam holes have been drilled, until now for bord and pillar sections, but the results are being evaluated for later application to shortwall faces. Adjacent seams pose problems at some sites and vertical and cross measure boreholes are now being considered.

Jan 1, 1993

By Robert L. Runkel, Kenneth E. Bencala, Briant A. Kimball

Thousands of abandoned and inactive mines are located in environmentally sensitive mountain watersheds. Cost-effective remediation of mining sites in these watersheds requires knowledge of the most significant sources of metals to surface waters. The significance of a given source not only depends upon the concentrations of a toxic metal, but also on the total mass, or load of metal added to the stream. To determine loads, we combined tracer-injection methods, to provide reliable discharge measurements on a watershed scale, with synoptic sampling, to provide spatially detailed concentration data. The resulting load profiles indicate which sources have the greatest effect on streams, where natural attenuation of metal loads occurs, and where ground-water inflows are located. This is part of the information needed for planning remediation of mine-drainage effects. The approach is illustrated by comparing zinc loading curves from three watersheds affected by mine drainage.

Jan 1, 2000

By Carl E. Schubert

The application of geophysical technology relative to the exploration, planning, and operation of coal mines is expanding. This is due to the trend of the industry to increase the size of operations, use of mechanized equipment and mining of more difficult coals, where unforeseen conditions can affect mine profitability. Coal is a good geophysical target because of its lower density, higher electrical resistivity, lower seismic wave velocity, and lower magnetic susceptibility in comparison to typical country rock. The more important techniques are well logging, high resolution seismic reflection, seam wave velocity, and radar. These methods can be used to map coal horizons, determine the physical properties of the coal, and identify mining hazards. The methods are not a pancrea however. Their use should be based on a careful assessment of their expected success and cost benefit analysis in comparison with conventional technology, primarily drilling, which none of the techniques presented should entirely replace. In general, the level of technology developed for geophysics surpasses their current level of application to coal problems. In some cases, identifying hazards in advance of mining using seam wave seismic in particular, the state of the art has been developed in Europe and is awaiting fruitful application in the United States.

Jan 1, 1982

By L. M. English

In the past 30 years, the research arena has changed significantly in all fields, mining included. The relative representation of the topics of research, how the research is performed, and who has performed the research have all changed significantly over these decades. Although there are a lot of subjective ideas concerning these changes, and there is a fair amount of anecdotal "analysis," there has been no actual study of these trends to verify the facts. The period studied is divided into six five-year periods for the purposes of comparison. Some of the trends analyzed are as follows: ? Co-authorship ? Research areas ? Research sponsors ? Cooperative efforts

Jan 1, 1995

By M. Moats, J. Young

Short term laboratory cell electrorefining experiments were performed to examine the impact of electrolyte composition, current density and temperature on deposit structure, roughness, and adhesion to 2B mill finished 316L stainless steel. Copper electrodeposits were produced using synthetic electrolytes with thiourea and the continuous addition of glue. Deposit structures were evaluated using X-ray diffractometry. Surface roughness was measured using profilometry and analyzed using scaling analysis. Finally, an internally developed method was used to measure the force required to remove the electrodeposited copper from stainless steel to determine adhesion strength.

Mar 2, 2022

By James F. Holzbach

Although Disputes Review Boards have been used for some time, they had not received wide publicity at the time Monroe County first used one. Public owners frequently resist adopting new contracting practices. This paper discusses an owner's experience with Dispute Review Boards, from learning about them to their use on two (2) projects. The experiences of potential and actual contractor claims are compared to a claim on an earlier contract and the ensuing litigation. Suggestions for possible use for Owner-Engineer disputes and recommendations for use are provided.

Jan 1, 1995

By B. Kraus

Many of us who have interacted with senior executives from leading oil and gas companies over the last few years on the subject of HSE performance have observed a marked shift in their engagement on this aspect of their business performance. There seems to be a shared impression that HSE performance will have markedly increased impact on their businesses going forward. On the back of this very real concern, many are taking material actions to secure a step change in their safety and environmental performance: hiring respected mainstream operational personnel to lead their HSE function; investing in capacity/skills development for HSE professionals to increase their effectiveness in addressing the needs of the business; taking a hard look at the efficacy of established management and audit programs (too much paper, not enough results?); investing in information management systems so they can have access to real time reliable performance indicators; and, critically, initiatives to reduce accident statistics (especially focused on fatalities and contractors? activities) and deliver meaningful reductions in their environmental footprints. Underpinning all of these actions is a clear sense that substantial, very well-intentioned activity and investment in HSE aspects of the business has not been hitting the mark and yielding too little return in terms of performance improvement. The very serious recent events on the US Gulf Coast and at a refinery in the US Pacific Northwest have added fuel to this fire. The need for approaches which will secure a step-change in performance on the front line in the global oil and gas industry has never been greater.

Jan 1, 2011

By Edgar Urbaez

Production scheduling is one of the most important factors affecting mine planning. A program -Mine Scheduler -that aids mining engineers with the setup of an optimum open pit production scheduling algorithm has been developed. A mathematical model for open pit scheduling that optimizes the Net Present Value of the cash flows was formulated. A simulated data is formulated as a Mixed Integer Linear Programming (MILP) problem. What's Best by Lindo Systems is used as the MILP solver in Microsoft Excel. The implementation of the algorithm focuses on problem setup, allowing users to easily evaluate, simplify, and develop the model that best fits their production scheduling.

Jan 1, 1999

By J. Hunter

The Highland Uranium Project in Wyoming is an in-situ leach (ISL) facility owned and operated by Power Resources Inc. It is the largest uranium producer in the U.S. and the largest uranium producer by ISL in the western world. With its limited capital investment and low operating costs, the ISL technique has been demonstrated to be an effective and environmentally sensitive method for recovering minerals from these low grade and otherwise uneconomic orebodies.

Jan 1, 1996

By A. Masutomi

Although great strides have been made during the past two decades in the reduction of the severity of accidents and injuries in underground coal mining, the number of accidents resulting in disabling injuries and lost time has continued to increase. Looking ahead to the 1990s, the reduction of accidents and incidents typically found in these latter categories should be emphasized in safety training for underground coal mining. Loss control is an approach which shows promise for applications in mine safety training since loss-control strategies focus on the pre-contact stages of an incident rather than on the incident, itself. Applied to safety training, the heightened awareness of personnel to workplace hazards at the pre-contact stages should result in a reduction of accidents and injuries. This paper explains the concept of loss control and shows how it can be applied in the development of the needs assessment for miner training programs. An example, based on research conducted at the continuous-miner worksite, is provided.

Jan 1, 1991

By Robert A. Irvine

Traditionally, cost effective gains in the capacity of material handling systems were a result of increases in equipment size. In general, the use of maximum capacity components in a system optimizes the production "costs per ton." The trend-"Bigger is Better" will continue in material handling equipment. Since it is rare for plant operators to lament an over abundance of screening capacity, one can safely predict that vibrating screens will follow this trend. Large Vibrating Screens - The Challenge Large vibrating screens represent a unique challenge for Manufacturers, Plant Designers, and Plant Operators. The inherent mode of operation for vibrating screens is self-destructive. More often than Manufacturers admit, Designers plan for, or Operators staff for, a vibrating screen succeeds and self-destructs. This is a problem. It can magnify with larger vibrating screens.

Jan 1, 1983

By Robert V. Price

It is a pleasure to be here today to discuss coal's prospects with the Society of Mining Engineers of AIMS--- a group destined to play a crucial role in shaping our national energy future. Much has been said lately about attaining domestic energy self-sufficiency, but to date, little has been done. Oil tankers from Venezuela and Kuwait continue to glide across the seas to meet our incremental energy needs. Meanwhile, our principal domestic energy resources -- oil and natural gas reserves in the Outer Continental Shelf and the oil shale deposits and the coal lands of the West -remain untapped. Help, however, appears to be on the way. In a forceful address last fall, President Ford called for the elimination of oil as a fuel for base-loaded power plants and its replacement with coal by 1980. He also urged the accelerated leasing of federal lands on the Outer Continental Shelf, the resumption of coal leasing on federal lands, and the development of a new energy conservation policy. There are, of course, many details left to be worked out. Language must be developed to put statutory flesh on the conceptual bones spelled out by the President. Congress must act. Regulations must be approved and tested, if need be, in court.

Jan 1, 1975

By R. E. Cook

"Mineral deposits require substantial amounts of energy to transport and be processed into useable form, and as such present a real processing challenge in that the deposits are never homogeneous and ore body compositional characteristics are all over the map! Extracting the desired mineral(s) from the deposit at sufficient profit margin, despite severe fluctuations in market price, requires process automation architecture capable of supporting an integrated enterprise solution. Such an architecture will encompasses the activities of individuals, process units, process areas, plant level activities, mine management and business planning and accounting systems. Key to the automation process is the aspect of value generation. This paper brings together the various requirements for the automation of a mining enterprise and presents the different aspects of how to obtain value across the entire mining operation.INTRODUCTIONMinerals’ processing sites are historically long lived, 20 year life of mine is not uncommon and 75 years is not unheard of. Considering that hardware technology advancements are introduced every six months, or less, it is prudent to select process automation systems that adhere to “open” industrial standards versus proprietary based systems. In the minerals processing industry, the key to survival is driving the cost of production per unit volume to the lowest possible level and provide enough profit to sustain operations. Control system architecture and Business information technology are rapidly becoming important tools in the quest for productivity. Getting key dynamic business performance information at the right time to the right person or process unit is crucial to successfully achieving corporate goals. The process automation architecture selected must therefore be able to integrate to the various networking enterprises and business systems.The mining industry is generally known as an “extractive” industry that is very physically-oriented with respect to operations and the activities in which workers engage. Large numbers of people performing manual tasks in difficult surroundings, produce very variable outputs. But, times are changing – and so are industry best practices. While the nature of work still consists of activities such as ore extraction, ore movement, ore concentration, refinement and logistics, automation innovations are starting to change the nature of many of the production steps. The industry has transitioned from requiring more physical activities by workers, to more information management, automated control and collaboration within the operation. Humans are good at situational intervention and non-linear reasoning and do best when empowered with an overall production perspective. Machines and automation are good at repetitive functions, steady state operation, and managing transitions. Thus, a combination of advanced technology solutions, reliable and useful information and full human contribution are necessary to mining operations for value generation."

Jan 1, 2015