Search Documents

By T. F. Torries

The primary merit criteria used by the mining industry is internal rate of return (IRR) rather than net present value (NPV) although NPV is favored by academicians. This paper discusses the problems with IRR and NPV and compares the multi-goal nature of decision makers and their need for information with the characteristics of NPV and IRR. Conclusions are that both NPV and IRR are needed for investment ranking, that NPV suffers the same multiple root problem as does IR.R, and the determination of incremental IRR to reach NPV consistent project ranking is misguided in practice.

Jan 1, 1997

By N. A. Abdel-Khalek

The objective of this investigation was to compare the results of counter-current flotation column versus conventional flotation cell for the cleaning of a sulphur ore and its discrete size fractions. The tests were carried out using diesel oil as a collector and alcohol as a frother. Generally, flotation column produced concentrates of higher grade. For example, the grade of a rougher concentrate for a given feed obtained with the column increased by 33% higher than that produced with the flotation cell. Such higher grade could not be obtained using conventional cell even after 3 cleaning stages. Moreover, the column gave superior results for flotation of fine and ultrafine particles.

Jan 1, 1991

By A. John R. Hart

INTRODUCTION In each given set of operational criteria for tunnel design, ground conditions dictate the selection of the most appropriate construction method and tunnel lining. The designer has the responsibility to choose or restrict the choice of the tunnel lining to insure that the final solution provides a cost-effective permanent construction which will require the minimum of maintenance and endure to the benefit of future generations. This Paper deals with some of the aspects of precast concrete tunnel linings, their history and development through the years. It does not purport to be a comprehensive review of all that has ever been tried or developed but, hopefully, a starting point to encourage discussion and development for the future. BOLTED LINERS As a result of anticipating a shortage of cast iron tunnel lining in 1936 when work was proceeding on London Transport's Central Line Metro, a design for the precast reinforced concrete bolted lining was born. The design took the form of the traditional cast-iron lining but with substantial concrete stiffeners to take the shield ram forces. This new lining was used to construct some 14,000 feet of running tunnel using a ring width of 1'8" which was the standard cast-iron width of the time. (Groves, G.L., 1943)

Jan 1, 1987

By S. Alpay

Underground mining method selection (UMMS) is one of the most important decisions that mining engineers have to make. Choosing a suitable underground mining method to extract a mineral deposit is very important in terms of economics, safety and productivity of mining operations. In real life, UMMS is one of the Multiple Attribute Decision Making (MADM) problems and decision makers have always some difficulties in making the right decision in the multiple criteria environment. Analytic Hierarchy Process (AHP) and Fuzzy MADM (FMADM) are the MADM tools and can be used for the selection of the best underground mining method by considering the problem criteria. UMMSMADM is a computer program which is based on AHP and FMADM and it can analyze the UMMS problems and produce the best underground mining method considering different deposit shapes and ore bodies.

Jan 1, 2010

By M. C. Manderson

Phosphate rock is a naturally occurring mineral which, in upgraded form, is important to both agriculture and industry. Phosphate rock normally must be upgraded before it can be assimilated and used. Most of this upgrading is now carried out by chemical means, largely through the reaction of a strong inorganic acid (primarily sulfuric acid) with the phosphate rock to remove major impurities and to produce soluble phosphate. A less important but yet still commercially significant conversion method involves the thermal reduction of phosphate rock at high temperature in an electric furnace to produce elemental phosphorus. The elemental phosphorus is then converted to usable end products. This conversion route is a more costly method than the chemical route, but it has the advantage of being able to produce chemically pure phosphorus derivatives. On the other hand, the use of phosphate rock for agricultural application-primarily for use as a plant nutrient ingredient for fertilizer -does not require the same level of purity. As a consequence, the chemical method of phosphate rock upgrading is the predominant technique for producing phosphatic fertilizers.

Jan 1, 1977

By Drupad B. Desai, Alexander Rosenbaum

In recent years, there has been an increasing use of two-pass tunnel lining system consisting of segmental unbolted expandable precast concrete initial lining and cast-in¬place concrete final lining in the United States. Used so far in soft ground tunneling performed under free air, it often includes a waterproofing or gasproofing membrane placed between the initial and final linings. This paper describes the utilization of this two-pass system for an extension of the Baltimore Metro, constructed in part under compressed air. It offers a description of the extension project, known as Section C; addresses the tunnel lining selection process and the design of the lining elements; examines the effect of the adopted lining system and tunneling technique on the design of the project's major structural components; and describes design modification instructions in order to accommodate constantly changing field conditions.

Jan 1, 1993

By John R. Wright

This paper reviews the increased use of mechanization in order to develop lateral headings efficiently and economically. Particular emphasis is placed on the role of the Electric-Hydraulic Drill Jumbo in achieving this goal. Also, the use of modified mining equipment to suit various operating conditions is discussed.

Jan 1, 1981

By Ronald Allum

Arizona leads all other states in the value of gemstones produced with an annual production which exceeds $3,000,000. Gemstones are an important component of the mineral wealth of the State. Turquoise, peridot, chrysocoll a, petrified wood, fire agate and crystallized mineral specimens are among the gemstones commercially mined. Numerous additional deposits are operated by hobbyists. The State's reputation as a source of gemstones and specimens for the collector and lapidary adds to the economy of the State by attracting tourists. Production of gemstones further adds to the State's economy through employment in the value added gemstone processing industries and by employment of Native American craftsmen.

Jan 1, 1988

The extraction and recovery of gold from copper electrorefining slimes by leaching and solvent extraction using dibutyl carbitol (DBC) has been practiced for several decades. Yet, the deportment of some common elements in this process has not been reported. The focus of this paper is to report the behavior of copper, bismuth, silver and selenium during the processing of industrial solutions by batch and continuous extraction on the laboratory scale. It was found that DBC, while an excellent extractor of gold from a highly oxidative chloride leach solution, also loads significant quantities of Cu, Bi, and Se. Silver was not present in significant quantities in the leach solution nor did it load appreciably. The deportment of gold and impurities are reported for batch and continuous operations of a two-stage extraction process using distribution ratios and separation factors.

Jan 1, 2010

By William Gleason

"On April 4, 2017, the largest earth-pressure-balance tunnel boring machine (TBM) ever built finally completed its 2.7-km (1.7-mile) journey beneath Seattle, WA, nearly four years after it began boring the SR-99 tunnel that will eventually replace Seattle’s Alaskan Way Viaduct.By now, readers of this publication are familiar with the ordeal that began on Dec. 6, 2016, when the machine overheated and shut down. Until that point, the TBM, named Bertha, had grabbed headlines for being the largest in the world with a 17-m (57.6-ft) diameter face. But after the incident that stopped the progress, the headlines suddenly stopped focusing on the engineering marvel of the tunnel project and began asking what went wrong. Just 300 m (1,000 ft) into the tunneling journey the machine was stuck, unable to move forward and impossible to retract.The project’s contractors, Seattle Tunnel Partners,(STP JV) – a design-build consortium comprised of Dragados - USA, Tutor Perini, say a 20-cm (8-in.) steel well-casing buried in the path of the machine caused the problems that halted the TBM. The Washington State Department of Transportation (WSDOT) disagrees, and the issue over who ultimately pays for the repairs is now with the courts.Eventually, engineers determined the best way to get Bertha back to work was to dig a 36-m (120-ft), deep concrete lined shaft pit in front of the machine and lift the 1.8-kt (2,000-st) cutterhead out for repairs. The repairs took two years but eventually the machine resumed mining in January 2016. In April 2017, the TBM finished building the tunnel, breaking through at the tunnel’s north end near Seattle’s Space Needle, with little to no ground surface movement measured on the entire alignment.While the cause of the TBM breakdown and who should pay for repairs was debated above ground, the work below ground continued. David Sowers, deputy program administrator, engineering and program management with WSDOT, told Mining Engineering during the 2017 Cutting Edge Conference in Seattle that in addition to the technical marvel that the tunnel became, the fact the parties involved were able to work through the unprecedented challenge is a great example of how to overcome challenges on massive projects."

Jan 12, 2017

By C. E. Roessler

Uranium and its decay series are associated with phosphate deposits of marine origin. Uranium concentrations are on the order of 100 to 200 ppm in matrix from the Bone Valley formation of Central Florida and about 25% this value in matrix mined from the Hawthorne formation in North Florida. Occupational radiation exposure due to this source has been under study in Florida since the mid 1970's (Windham, Partridge, Horton 1976; Roessler and Prince 1978). This report is based on findings of an industry-wide scoping survey conducted by the University of Florida during March 1976 through May 1977 and subsequent studies in selected individual facilities. PHOSPHATE MINING OPERATIONS Mining and beneficiation operations are diagramed in Figure 1. At the excavation site, electric powered draglines remove the overburden and expose the phosphate matrix (ore) which is then slurried and pumped to the beneficiation site. At the washer stage of the beneficiation plant, the matrix is subjected to washing and screening. A coarse product, "pebble" is produced and sent to storage piles while the fine fraction is passed through a series of cyclones to remove the clays. The generated clay suspension is sent to settling ponds while the remaining sand-sized fraction is sent to the flotation plant. At the flotation plant, phosphate particles are recovered from the fine sand particles of similar size through several stages of treatment with reagents, agitation and separation of floating and sinking fractions. The high grade concentrate produced is transferred to storage while the sand tailings are discarded. [ ]

Jan 1, 1981

By A. W. Khair, S. S. Peng

Discussion by J. Parker Gentlemen; Rainy day in Upper Michigan, a good time to catch up on reading. Am doing that, and have a couple of questions concerning the K and P paper on roof problems and supports. I wonder if the authors can enlighten me. The compressive strength of the coal was reported as 4.4 MPa (633 psi) and compressive stresses measured in the coal seam were reported at around 27.6 and 48.2 MPa(4000 and 7000psi ). Can such a soft coal actually contain such a high level of stress? Can it be measured as if the material were elastic, or does the coal behave plastically? Can that stress level be confirmed with hydraulic load cells? And if the coal is so soft, and if it is plastic, why is the stress field not hydrostatic'? The intact roofrock appears to be unusually strong, with compressive strength reported at around 145 MPa (21,000 psi), and some failures were noted as soon as the rock was exposed. Were tests run to find out how that rock responded to the addition of moisture, from sprays or from humid air? Did moisture weaken the rock? Did it cause the rock to expand quickly, thus to induce internal compressive stress? How can the near-vertical cutters, as shown in the photographs, be attributed to primarily horizontal stresses? Did the cutters follow any particular pattern in the development panels, which might be related to a particular stress pattern? For example, did they always appear alongside the stiffest pillar? Or always along the northwest rib? Was there any evidence of the pillars and entries "rotating" under the influence of differential horizontal stresses? How much did the entries and pillars rotate as the longwall face approached and passed? After rooffalls, did the openings assume shapes which would indicate a preferred shape in that stressfield and geology? Did crosscuts always survive without damage, as shown in the sketch?

Jan 1, 1992

By Robin Dill, Julian Prada, Kathryn Kelly, Brian Hann, Todd Moline

Narragansett Bay Commission’s (NBC) Pawtucket Tunnel Project includes construction of the 11,600-ft long, 30-ft ID, deep rock tunnel. This paper presents insight into the features and benefits of lump-sum, design-build that led NBC to select it as the project delivery method. The use of a design-build contracting process that included proprietary meetings to discuss and obtain feedback on Alternative Technical Concepts as well as to facilitate reaching consensus on modifications to the GBR-B is also described. The discussion includes features and benefits of design-build process that not only addressed NBC’s desired outcomes, but also allowed the Design-Builder to propose several innovative changes to the Base Technical Concepts included in the bid documents, and to develop a GBR-C that was compatible with their proposed means and methods of construction and addressed what they believed to be the more significant subsurface risks on the project.

Jun 13, 2023

By N. T. Rogers

An accepted statement of fact is that transportation next to agriculture is the second most important industry in the world. The transportation networks of the United States contributed immensely to the growth and prosperity of our nation. My objective is to make each and everyone here aware of the need for communication between geologists, mining engineers, purchasing agents and transportation managers. Only through a cooperative effort is it possible to reap the benefits of transportation in the industrial minerals field. Transportation is often thought of in terms of trucks, rail cars, barges, covered wagons or whatever. If this is your only exposure to the transportation industry then you probably spent most of your life in a cave.

Jan 1, 1989

By A. L. Mular

Optimization has been defined as the procedure of locating the best of something or the best way of doing something (Mular, 1971). Several texts (Himmelblau, 1972; Ray and Szekeley, 1973; Box and Draper, 1969; and Lee, Adams, and Gaines, 1968) on the subject are available. Such techniques have been placed in two categories, namely, off-line optimization and on-line optimization. For the former, an optimization model is employed; for the latter, a black box approach is involved. The essence of an optimization problem becomes obvious, when a response surface is considered. Suppose that a response (in this case, a criterion of improvement such as profit per day; grade of concentrate per day) denoted by Y, depends only on two variables, X1 and X2, which can be manipulated and controlled. The relationship between Y, X1 and X2 may be represented graphically as shown in Fig. 1. The diagram is called a response surface and its height, Y, is determined by X1 and X2. Points associated with equal responses constitute response contours. The shape is that of a hill, and optimization is the procedure of ascending the hill to reach the top (maximum). In practice, a response surface is subject to disturbances which distort its shape and shift its location from time to time, so that the exact location of a maximum is imprecise. Generally, constraints (restrictions of some sort) on responses and manipulable variables serve to define a region of permissible operation.

Jan 1, 1979

By B. Basim

Novel chemicals that can be used for increasing the efficiency of fine coal dewatering were developed at Virginia Tech. Reagent A was tested on three different coal samples in laboratory vacuum filtration tests. These included flotation products from Middle Fork plant, Elkview Mining Company, and CONSOL, Inc. The tests conducted with the Middle Fork coal sample (100 mesh x 0) showed that cake moisture can be reduced by more than 10% beyond what can be achieved without using dewatering aid. This improvement was achieved at 1 lb/ton of Reagent A and 0.1 inch cake thickness. At 0.5 inches of cake thickness, the improvement was limited to 8% at the same reagent dosage. The results obtained with the Elkview coal (28 mesh x 0) showed similar advantages in using the novel dewatering aid. Depending on the reagent dosage, cake thickness, drying cycle time and temperature, it was possible to reduce the cake moisture to 12 to 14% range. In addition to achieving lower cake moisture, the use of Reagent A substantially decreased the cake formation time, indicating that the reagent improves the kinetics of dewatering. The test results obtained with CON SOL coal were not as good as with the other coals tested in the present work, which may be attributed to possible oxidation and/or contamination.

Jan 1, 1998

By Jianliang Li, Xi Peng, Guorong Lu

This paper describes a wind tunnel modelling study on airflow and pollutant concentration in a large open pit mine located in southern China. A 1:1000 scale model of the surface mine was fabricated and placed in a wind tunnel. Airflow velocity in the test section of the wind tunnel can be continuously adjusted from 0.3 m/s to 6.0 m/s. In this study, both the present pit condition and the projected final pit condition were modelled. Airflow direction and velocity profiles were obtained. The impact of wind direction and velocity on airflow was also studied. The pollutant concentration distribution in the open pit was simulated using smoke, and a distribution profile was obtained. Respirable dust concentrations at the mine site were measured, then its concentrations at the projected final pit condition were estimated using the obtained pollutant concentration distribution profile. Under normal meteorological conditions, it is expected that the respirable dust concentration for the final pit should not exceed the government standard. Key Words: wind tunnel modelling, open pit, surface mining, scale model, mine ventilation, airflow profile, point source.

Jan 1, 1993

By P. Hambach

Murer Company, Andermatt, Switzerland, can claim to have done pioneer work in the construction of inclined shafts. This happened in 1968/69, when we decided to bore with a Wirth tunnel borer an inclined shaft, 1100 m in length, 3.0 m in diameter, and with a grade of 65%, in the 2400 kilo pascall per sq. cm granite of the Montblanc Massive. The whole excavation was accomplished in ten months which, at least for European conditions, can be claimed as a record. It was, at least to our knowledge, the first inclined shaft to be bored full-face (Fig. 1). Encouraged by the experiences and performances attained at Châtelard, we approached other projects of the same kind. We were awarded, together with Hochtief Ltd., Essen, a contract from Schluchseewerke, Freiburg, Germany, in December 1969, for the construction of a penstock for the Hornbergstufe at Wehr, Germany, with a diameter of 6.3 m. This inclined shaft with a grade of 55% is located in Schwarzwalder granite with a compressive strength of up to 2000 kilo pascall per sq. cm, about 31,000 psi. As no exact geological data were available about the rock to be worked, and a fault zone from 80 to 150 m long had to be faced, as well as a few individual fissures of varying thickness, it was decided to use the multi-stage method. The 3-m diam tunnelling machine which had driven the oblique shaft at Châtelard had now finished work, and an immediate beginning was made with driving the pilot staft. This was very welcome to the contractor, since exact information about the type of rock present and the inflows of water was required immediately and before the final borehole diameter was fixed, for the purpose of dimensioning the supports to be subsequently installed.

Jan 1, 1974

By Robert A. Jankowski, Charles Babbit, Natesa I. Jayaraman

The Bureau of Mines, together with Foster Miller Inc., has developed a compact, high pressure scrubber system for continuous miners. Powered by water energy alone, it can move up to 1.4 m3/s (3,000 cfm) of air and scrub a significant amount of the dust in the air. Full- scale model and underground trials showed excellent performance. Operated at 8.3 x 10[3] kPa (1,200 psi) and 38 L/m (10 gpm), the scrubber has reduced operator and return dust concentrations by more than 50 pct. This paper describes the full-scale model development, system fabrication and underground evaluations of this novel and inexpensive scrubber.

Jan 1, 1989

By D. R. Spears

The U.S. Bureau of Mines has developed a Fast Air-injected hydrocyclone-Shallow Tank (FAST) flotation system. Conventional flotation cell kinetics are a compromise between two conflicting requirements, the need for an agitated zone for rapid bubble-particle collision, and a quiescent zone for bubble-pulp separation. The Bureau of Mines has designed a flotation system in which bubble-particle collision and bubble separation are carried out in two discreet unit operations. A bubble slurry was mixed with an ore slurry at a high rate in a modified air-injected hydrocyclone for rapid bubble-particle collision. The mixture was then fed into a unit specially designed for rapid separation of the bubbles from the pulp. A conventional flotation cell required 2.8 min to obtain 90 pet recovery at a 7-pct Cu rougher concentrate grade, whereas the FAST flotation system can obtain 85 pet recovery with a 13-pct Cu rougher concentrate grade in 0.28 min, and 92 pet recovery with a 7-pet Cu grade in 0.56 min. The Bureau's FAST flotation system is adaptable to a wider variety of flow sheets and could potentially allow for replacement of conventional flotation cells with smaller and faster units.

Jan 1, 1991