Search Documents

By I. O. Otunniyi

The natural hydrophobic response flotation method for beneficiation of printed circuit board comminution fines (PCB CF) still requires many studies to further basic understanding of the process and the flotation traits that the PCB CF presents. Varying particle size distribution (PSD) and water recovery under the scheme show that higher mass pull, obtained at the finer PSD, gave lower water recovery but higher value loss. The reverse also holds: the least mass pull at the coarsest PSD used, -106 + 75 µm, gave the highest water recovery per unit mass pull with the highest reverse recovery. This is unlike what obtains in primary resources processing, where higher water recovery is often with increased fines entrainment. The reverse recovery loss here is, therefore, more due to entrapment with the heavy mass pull characteristic of the method than to the entrainment of value with water. Other peculiarities of the system observed are discussed, with the goal of improving the performance of the process, and broadening the general knowledge of flotation systems.

By H. Colin

The basic industry, such as mining, ferrous and non-ferrous, cement and aggregates, stores and handles millions of tons of raw materials, re- quiring often different types of storage, blending and reclaiming systems.

Jan 1, 1980

By Richard Giffen, Martha Gross, Luca Pellegrini, Pa Ousman Njie

The Hampton Roads Bridge-Tunnel (HRBT) Expansion project in Virginia includes parallel 1.5- mile (2.4 km) tunnels constructed using a tunnel boring machine (TBM). The TBM launching and receiving shafts were excavated within the footprint of two reclaimed islands abutting the navigation channel for the Port of Virginia. The shaft excavations—a circular tri-cell shaft at South Island, and a circular-rectangular twin-cell shaft at North Island—were supported by slurry walls up to 190 feet (58 meters) below the island surfaces. This paper describes specic design considerations for these shafts, as well as construction and uality-oversight aspects of their excavation and construction.

Jun 23, 2024

By R. J. Mirville

Flocculation is an important step in the treatment of coal preparation waste waters. The effects of polymer charge and molecular weight and solution pH and ionic strength on the adsorption and flocculation characteristics of a series of polymeric flocculants on some typical waste water constituents have been studied experimentally. The results indicate that the nature and extent of flocculation are strongly system-dependent. For the case of coal, both adsorption and flocculation behavior can be correlated with the polymer conformation in solution. For the mineral constituents, on the other hand, adsorption and flocculation depend also on the surface properties of the solid.

Jan 1, 1979

By Joseph M. Zigich

The Anaconda Minerals Company operates a molybdenite and copper producing mine and mill facility near Tonopah, Nevada. Included with the milling facility is a ferric chloride leach plant for removal of copper mineralization from the molybdenite concentrates. Discussed are the engineering and construction schedules associated with the leach plant. The chemistry associated with the process along with a description of the process flow, equipment, and operating parameters are contained in the paper.

Jan 1, 1983

By John E. Tilton

Mining is one of the oldest human activities. It goes back at least to the Bronze Age and possibly even the Stone Age. The Romans mined copper in Spain and tin in England some 2,000 years ago. The writings of Agricola in the 16th century show that mining was important in the Middle Ages. Today, more mineral commodities are mined in greater tonnages than ever before. This long and fascinating history closely tied with the economic development of the human race is one of the charms of the mining industry. It also, unfortunately, gives rise to some widespread misconceptions. Old industries are generally considered stodgy with mature and stagnant technologies. Costs tend not to decline as in newer industries, and may even increase with real wages. Costs are particularly expected to rise in the case of mining as the best mineral deposits are depleted. Thus, mining is often thought of as a sunset industry, destined to decline over time as the resource base is depleted. These perceptions have several important implications. They argue against economic policies that rely too heavily on mining and mineral processing to foster growth and development. The best and the brightest young people, along with society's other valuable resources, should be encouraged to enter newer industries. There the technological opportunities and the prospects for growth are more promising. These perceptions also suggest that the ability to compete in the mining industry depends largely on the quality of a company's or country's mineral deposits. Mining will take place first in countries with the lowest-cost deposits. Once these are exhausted, mining will shift to countries with the next best deposits. From time to time, new discoveries may also produce a shift in the location of mining, [ ] and may even for a time keep the costs and prices of mineral products from rising. Over the longer term, however, rising costs and prices are inevitable, as the world is forced to exploit poorer mineral deposits.

Jan 1, 1997

By J. R. Schafler, J. L. Brinkman

"The US coal mining industry has suffered a recent decline in profits caused by a combination of decline in commodity demand and more restrictive government regulation, forcing coal mining companies to cease production in numerous mines. A 40% decrease in the total number of coal mines occurred from 1994 to 2000. The number of mines remained relatively constant until 2008 when a change of government sparked a series of new environmental regulations which have contributed to another 15% decrease from 2008 to 2016. In contrast, production has only decreased by 3%, increasing from 1994 to 2008, and then decreasing since 2008. However, this value is skewed by large increases in sub-bituminous coal production and decreases in other coal ranks. Several aspects assist in executive decisions on mine longevity and economic worth. Studies of open source mine data collected by mandated government surveys coupled with commodity history can be used to find relationships between mine closures and these elements, which include statistics on production tonnage, seam height, coal rank, etc. This paper looks at coal mining trends since 1994 by comparing mine, market, and regulation factors that may influence mine closure. INTRODUCTION The US coal mining industry is currently experiencing a decline in both demand and commodity price while facing implementation of more stringent air and water pollution regulations. Company profits have decreased significantly, forcing several major companies to declare bankruptcy. The industry was required to adapt to survive. Many of these companies have adjusted by abandoning mines; the last two decades have seen a drastic decrease in the number of mines. To discover the primary causes of this downturn, three major aspects must be studied: properties of abandoned mines, commodity history, and regulatory impact. TRENDS SINCE 1994 Each year, US coal mines are required to submit data on a wide variety of categories to the Mine Safety and Health Administration (MSHA) and the US Energy Information Administration (EIA). This data includes administrative records, production values, and information regarding the attributes of the mined material and the mine itself. Each year since 1996, EIA has released a report summarizing the data from two years prior. Additionally, MSHA maintains a database containing a collection of all the most current data. These resources are the primary sources for the following figures."

Jan 1, 2017

By Cuthbert Musingwini, Adeodatus S. Nhleko, Mahlomola I. Mabala

Optimization of a three-dimensional (3D) underground stope layout is complex given the number of variables and constraints to consider, such as the stope size. Determination of the appropriate stope size in stope layout optimization problems is a complex process that must consider several factors including placement of infrastructure and development, production scheduling, and equipment selection. An inappropriate stope layout can result in unrealistic expectations for a production schedule, consequently negatively affecting the derived economic value. Therefore, this paper used a dual interchange algorithm (DIA) to evaluate the effect of stope size on the stope layout economic value (SLEV) for a synthetic Platreef mineral deposit planned for extraction using sublevel open-stoping. The results showed that generally as the stope size increases, the SLEV decreases. This aligns with practical mining because larger stope sizes have a higher chance of incurring more dilution which reduces economic value, while smaller stope sizes enable more flexible extraction where unprofitable blocks can be left unmined as waste, thus increasing the derived SLEV.

Jun 25, 2023

By Thomas D. Henderson

Este capítulo presenta- un "caso histórico" de los pasos a dar para estimar IDS castes de capital y operativos para un concentrador típico de cobre porfirico de ± 9;070 toneladas métricas de producción diaria. El concentrador que se describe es hipotético, pero está basado en la experiencia propia y es, en efecto, una composición de varios proyectos reales. Las cifras utilizadas son ilustrativas solamente y no representan los castes reales de ningún lavadero en particular. Estas cifras son, sin embargo, representativas de los castes tipicos de molienda en un punto en el tiempo y son to suficientemente precisas coma para iIustrar los procedimientos de estimación de castes descriIos en este capítulo, No es posible publicar cifras reales y corrientes de los castes del lavadero y, en cualquier caso, las cifras de Ios castes reales pierden rápidamente su significación en Ia actual situación económica con los rápidos incrementos de las diversas partidas que configuran los castes. El trabajo está dividido en tres partes: (1) orden de la magnitud estimada, (2) estimación def estudio de viabilidad, y (3) comparación entre los castes estimados y los castes rea¬les. Con vistas a este trabajo supondremas que una mina tiene una propiedad minera explorada mediante perforación con testigos que refleja un yacimiento, ampliamente definido, como de unas 45,3 millones de toneladas métricas con una ley del d,6°/ de sulfuro de cobre, Esta compañia desea obtener primero una estimación del orden de magnitud de los costes (canto de los costes operativos como del capital) para determinar si la pertenencia garantiza más perforación y desmuestre de testigos. Suponiendo que esta evaluación económica obtenida utiIizando Ia orden de Ia magnitud de Ios costes sea favorable, sera a continuación requerido un estudio de viabilidad más preciso de los castes de capital y operativos. Seguidamente of recemas una descripción de los diferentes pasos dadospara desarrollar ]as costes del orden de primera magnitud y a continuación para los castes del estudio de viabilidad.

Jan 1, 1982

By S. Mischler, J. Organiscak, S. Klima, C. Seaman

"Researchers at the National Institute for Occupational Safety and Health’s Pittsburgh Mining Research Division (PMRD) performed comparative testing of six hollow cone water sprays from three manufacturers: static swirl chamber sprays from Spraying Systems (BD-3, BD-5) and Steinen-Hahn (SH-3, SH-5), and movable swirl chamber sprays from Repair King (RK-3, RK-5). Water flow testing was completed at three operating pressures (60, 80, and 100 psig) where both sets of sprays (3-series and 5-series) produced similar water flows, deviating less than 8% from the average water flow rate at each pressure. Airflow induction testing was completed at 80 psig using a hot wire anemometer to take air velocity measurements upstream of the spray nozzles. Respirable dust capture efficiency testing was completed in a 14.5-m3 (512-ft3) closed system dust chamber at 80 psig. The dust capture efficiency ranged from 7.2% to 9.9% for the 3-series nozzles, and from 5.3% to 7.1% for the 5-series nozzles. Sprays were also analyzed using a Cloud Aerosol and Precipitation Spectrometer (CAPS), which uses light scattering to count and size the airborne water droplets from each spray. In both cases, Spraying Systems sprays produced the largest mean droplet size, followed by Steinen-Hahn and Repair King sprays, respectively. INTRODUCTION Coal mine worker overexposure to respirable coal dust continues to be a problem in underground coal mining operations in the United States. The U.S. Mine Safety and Health Administration (MSHA) now requires coal mine worker respirable dust exposure to be no more than 1.5 mg/m3 average over the actual working shift (CFR 30-70.100, 2016). Potential overexposure to respirable dust by continuous miner, roof bolter, and shuttle car operators may be prevented if proper safety and health practices are implemented as detailed in the mine’s ventilation plan (CFR 30-75.371, 2016). Water sprays are a necessary component of an underground coal mine ventilation plan. They are important on the continuous mining unit for moving air and removing respirable coal dust from the breathable airstream. MSHA requires underground coal mines to include the number, types, location, orientation, operating pressure, and flow rate of operating water sprays in their mine ventilation plans (CFR 30-75.371, 2016). Water sprays can become clogged, requiring the sprays to be properly checked, maintained, and replaced in order to continue meeting the ventilation requirements described in the mine ventilation plan.In an effort to eliminate the problems with spray clogging, Repair King has developed self-cleaning movable swirl chamber hollow cone water sprays (RK-3, RK-5). The spray’s movable swirl chamber is designed to only open when water pressure is applied to the spray nozzle, preventing the nozzle from clogging. Anti-clogging sprays could improve mine production by reducing the amount of time spent servicing clogged sprays. Also, these sprays could improve health and safety of miners since they would continue to suppress and capture dust and continue to move airflow at the face, while a clogged spray loses this ability until it is cleaned or replaced manually. The objective of this research was to assess the comparability of the Repair King sprays with the most commonly used sprays in underground coal mines using performance criteria. An assessment of the sprays self-cleaning or anti-clogging capability was not conducted."

Jan 1, 2017

By John G. Hall

Everyone forms his own mental picture when the subject of copper is mentioned. To an architect, copper is a warm, enduring metal with a quiet beauty; to the historian, man's first metal; to the product engineer, the best electrical and thermal conductor of all commercial metals; to the investor, a volatile stock; to the speculator, the daily price quotation; to those in the mining industry, the challenge of producing copper for rising needs in the face of rising costs and lower grades of ore. At this meeting, we will look upon copper as a key raw material in industry, in national defense, in technology, in world trade, and as a principal commodity in the economies of several developing countries. As miners, and most of us here are miners, we are prone to view our role as suppliers of copper. We locate, mine, smelt and refine the metal. In the complexities of today's world, however, following a period of the longest domestic copper strike in history which caused critical world-wide shortages and widely fluctuating prices; it becomes necessary for all of us to concern ourselves with the whole spectrum of copper affairs -"from mine to consumer " But first we need to look at the miner's side of the picture -- capacity and production. We will examine these functions in terms of the whole world -- not simply the free world. Nature did not endow all regions of the earth equally, and copper in world trade has a way of ignoring political boundaries. Science and technology, as well, know no national boundaries. It is said that the "Engineering & Mining Journal" has as many readers in the Communist World as in the Free World. Nor is this a one-way street. We presently have available to us in the. U.S., cover-to-cover translations of many Communist World mining and metallurgical journals.

Jan 1, 1968

By R. Worrall

The global mining industry has been proactive over the last decade in finding ways to embrace the concept of sustainability. However, legacy mine sites (which include abandoned derelict and orphan mine sites) across the world continue to present issues for the global mining community, governments, local communities and NGOs. Unfortunately there has been much less academic focus on this area of mining and sustainability. This paper seeks to address how principles of sustainable development can be used to guide the development of processes for addressing post mining landuse issues for legacy mining areas. This is being done using a case study area located near Ipswich, in southeast Queensland, Australia. This area has a 160 year history of coal mining, and was one of Queensland?s crucial early industries. Mining in the area ceased in 2003 leaving a degraded landscape covering an area in excess of two thousand hectares adjacent to one of the fastest growing urban areas in Australia. A sustainability criteria and indicators framework for post-mining landuse on legacy mined land, developed from current best practice used for measuring sustainability across a range of industries is being developed. A review of current best practice suggests the framework should: (1) consider in equal measure environmental, social and economic factors; (2) have a minimum number of indicators which should be easy to identify and measure; (3) must have indicators with a meaningful output; and overall, the framework must consider particular requirements of the site being investigated. Application of the framework to the case study area is an ongoing aspect of this research, and the results will be evaluated through the use of expert stakeholders.

Jan 1, 2007

By J. R. Hunter

The present is rooted in the past. This is particularly true in the case of mining operations. Coal mining in the United Kingdom is considered an old Industry comprising today 246 Coal Mines many of which have worked coal reserves in their locality for over 100 years. More than half the current producing mines lie in the Yorkshire and Midlands coalfields. They are in the oldest age group and produce 70% of the Industry's output. Some 50% of the remaining U.K. workable reserves amounting to approximately 98,000 million tons are still available to these regions. Fig. 1 Over the past two decades a gradual erosion of demand for coal in the U.K. has virtually halved the Industry's capacity. The number of Mines has reduced by 53% during the past 10 years. Productivity has increased by some 42% mainly through improvements in the central coalfields which has enabled costs to remain broadly competitive with oil.

Jan 1, 1976

By Ehsan Alavi, Eren Kusdogan

The City of Toronto’s Coxwell Bypass Tunnel is currently being constructed by North Tunnel Constructors ULC, a joint venture of Jay Dee Canada, C&M McNally Tunnel Constructors and Michels Canada. This project includes construction of approximately 10.5 km of 6.3 meter finished diameter rock tunnel, five 20 meter diameter storage shafts and eleven tunnel connection drop shafts, along with associated deaeration and adit tunnels. This paper describes progress on the project to date and reviews the risk mitigation measures utilized on the project to move the project forward through tough geological conditions during shaft excavation and tunneling phase of the project.

Jun 13, 2023

By M. L. Young

Hindered settling columns are used throughout the minerals industry for both size and density separations. In this study, the performance of a continuous, laboratory-scale hindered-settling column was evaluated for various particle systems. The test variables included solids composition, water rate, and column height column performance was evaluated using partition curves and corresponding performance parameters.

Jan 1, 1999

By Chris J. Conway, Bruce W. Atkinson, Graeme J. Jameson

The flotation of coal in the fie and coarse particle size ranges presents particular problems. Fine or ultra-fine coal less than 100 microns presents a challenge to conventional flotation machines because the rate of capture of the coal particles can be very low, so longer residence times are needed. Also, conventional mechanical cells are not normally designed with froth properties in mind. Froth drainage may be inadequate, leading to excessive entrainment of ash. The upper limit of flotation of coal is normally put at about 500 um (30 mesh). It appears that, in mechanical cells, coarser particles tend to be torn away from bubbles in the turbulent environment created by the impeller. In this paper, results are presented from plant trials of a high-intensity flotation column of novel design, namely the Jameson cell. Extensive trials have been conducted on coal slurries with a top size of around 1 mm. Size-by size analysis shows that it is possible to achieve high yields of low ash product over the whole particle size range.

Jan 1, 1995

By M. S. Klima

Coal gasification solid residue (slag) contains unconverted carbon (char), which is considered an impurity for utilization applications of slag. Under this study, table concentration was used to process approximately 24,000 pounds of a nominal-3.4 mm gasifier slag (-85% ash) to separate high (-100%) ash slag from low (-50%) ash char. The results indicated a nearly ideal separation of the slag from the char for sizes coarser than about 1 mm. An overall slag yield of 71 % was obtained. The slag was sufficiently clean to be used as feed material for the production of expanded lightweight aggregate. The recovered char had an ash content of about 47% and was a nominal -1mm in size.

Jan 1, 1997

By P. Schmäh

Nowadays, small diameter tunnels are increasingly considered in pipeline projects as an alternative for sensitive crossings or when soil conditions limit the use of conventional pipeline installation methods like HDD. Safety concerns play a key role, especially for inner-city installations. Pipe jacked microtunnels and small segment lining tunnels can serve as casing tunnels if access is required during construction for the change of cutting tools in challenging ground conditions or for maintenance of the pipeline in operation. Small diameter tunneling solutions offer a high degree of flexibility for alignment design in terms of geology, length and radius.

Jun 13, 2021

By Velu Annamalai

In-situ uranium solution mining involves the injection of a lixiviant (leach solution) through appropriately placed wells into the underground ore zone. Upon contacting the uranium minerals, this solution will dissolve the uranium. The uranium containing solution is then pumped out of the wells into a processing plant where the uranium values are removed, typically in ion exchange columns, and the stripped liquor is recycled back into the field. The lixiviants may be acidic or basic. Where the ore zone mineralization contains appreciable carbonate, as in the South Texas fields, acid consumption would be excessive and the typical solution is ammonium carbonate bicarbonate at about 5-10 g/l and a pH of 7-9. Because the usual uranium minerals, uraninite or coffinite, contain uranium in the insoluble tetravalent state, it is necessary to add an oxidant to increase the valence to the hexavalent state where the uranium is soluble. Oxygen dissolved in the lixiviant has been shown to be quite effective for this purpose. It is also much more economical than other oxidants. Of concern is the possibility that (1) its solubility may or may not provide concentration levels adequate to give an economically attractive uranium level in the extracted liquor, and (2) the addition of oxygen in excess of the saturation level so as to increase the uranium grade in the lixiviant may cause gas blockage of the typical fine-pored ore formations.

Jan 1, 1981

By Eudes Prado Lopes

The Mineral Resource Exploration Company - CPRM - a part-private, part-government concern jurisdictioned to the Ministry of Mines and Energy of Brazil, was founded in 1969 for the purpose of promoting the exploration of mineral and hydric resources throughout Brazil. The political-administrative framework within which it was conceived and created considering that an economic and financial balance to be maintained in all its fields of activity, CPRM set out right from the start to organize itself to perform -three basic lines of action, which can be summarized as follows: As a Service Company, to carry out those services requested by government agencies and by the private sector through of service contracts; As a Mining Company under the Brazilian Mining Code, aiming at supplementing private initiative, not beyond the field of mineral exploration;

Jan 1, 1975