Search Documents

By S. Ersayin

In 1998, the Concentrator Modeling Center was established within the Coleraine Minerals Research Lab, Coleraine, Minnesota, to develop models for simulation of iron ore processing plants, and to assist plant operators in improving performance of their aging plants. The short-term objective was to develop necessary models for reliable simulation using conventional techniques, while the long-term objective was set as liberation-based modeling and simulation of these plants. The short-term objective was achieved in 2002 after the development of models for magnetic separators, hydro-separators and fine screens. A project funded by the U.S. Department of Energy was carried out to demonstrate the capability in improving iron ore processing at the Minorca plant. As a result of this study, a 10% improvement in throughput at the plant was obtained, and simulation became a desired tool for plant operators. A significant step in the long-term objective was reached in 2005 with the development of a liberation model. This was followed by incorporation of models capable of processing liberation data into the software. By early 2007, the Concentrator Modeling Center had the capability of performing liberation-based simulation of entire plants.

Jan 1, 2009

By I. S. Parrish

One of the most common errors uncovered while performing a reserve, or resource, audit is not in the geological modeling or grade problems due to poor sampling, prepartion or assaying. The error most commonly found is in tonnage or, more specifically, in the tonnage factor - that factor applied to volume to derive tonnage. Tonnage factors In the metric system, the tonnage factor is the density, or specific gravity. Specific gravity (Sp.g.) is defined by Dana (1947): • "The specific gravity of a mineral is the ratio of its density to that of water at 4° C (39.2° F). • "Density is the mass of the unit volume or weight of the body divided by the weight of an equal volume of water." When Sp.g. is multiplied by the metric volume it yields metric tonnes. In the English system, the tonnage factor is usually expressed in cubic feet per short ton (cu ft/st). When the volume in cubic feet is divided by cu ft/st, the resulting figure is in English short tons. Table 1 gives the cu ft/st factors equivalent to specific gravities from 1.6 Sp.g. to 5.8 Sp.g. The table is based on the following equation: cu ft/st = 0.9072 divided by Sp.g. times 0.02832 The blase attitude that most geologists have toward tonnage factors is echoed in the prevailing definitions of Reserves and Ore, as provided by the US Securities and Exchange Commission (S.C Form S-18), Canadian National Policy 2A and the SME Proposal for Reporting Terminology (SME February 1991). In each case, it is stated that "quantity" (SEC, SME), or "tonnage" (Can.2A), "is computed from dimensions revealed in...." etc. Unfortunately, "dimensions" do not directly yield tonnage. Dimensions must be factored by density to derive tonnage.

Jan 1, 1993

By C. J. Roos

Ground engaging tools are used to prevent damage to the main components of earth-moving equipment. These tools consist of everything from shovel teeth to replaceable drill bits to dozer wear plates. The costs of these ?consumable? items are increasing with the costs of raw materials. This project developed a tool to be used by Newmont Mining Corporation to predict the consumption of excavator teeth. This paper presents the results of a Montana Tech research project in which an equation was developed to predict excavator teeth consumption based on production rates and rock properties.

Jan 1, 2009

By Zoheir Khademian, Morgan Sears

According to the 2010–2019 Mine Safety and Health Administration (MSHA) accident report database, 91% of reported ground control accidents in US longwall mines were caused by roof instability. Gateroads are subjected to significant changes in loading conditions from the development to the longwall abutment loading phases. When combined with thinly bedded shale roof, found in many US longwall coal mines, the design of efficient roof support becomes challenging. In previous work, the bonded block modeling (BBM) of roof by UDEC was validated against field extensometer measurements in a longwall entry roof at a 180-m depth of cover. The BBM was shown capable of capturing delamination and buckling of shale roof, one of the main roof instability mechanisms in longwall mines. This paper presents the recent findings on the roof-support interaction using BBM models of the same longwall entry. The effects of cable bolts, roof bolt density, and strap support on potential roof instability are studied. Results demonstrate the potential for BBM numerical models to help understand the complex roof and support system interactions and to assist with optimizing gateroad support systems.

Feb 13, 2024

By W. A. Wilkinson

In creating a surface mine design, a complicated series of events may be required to meet both mining and environmental objectives. Envisioning the mine at every step of the operation can greatly assist the engineer to identify design and operational problems that might otherwise go undetected until the field operations reach the problem. Providing operations a visual progression of the mine ensures that critical designs generated by the engineer are understood and effectively communicated to operations. Providing the plan as electronic data to the surveyors and/or on-board GPS systems can ensure successful implementation of the design. This paper discusses using computer technology to generate a virtual mine plan and strategies to consider when communicating a virtual mine plan through electronic and paper formats.

Jan 1, 2002

By S. Dixon

The Peñasquito deposit in Mexico is one of the largest grassroots precious metal discoveries developed in recent years. Goldcorp Inc. acquired the gold-silver-lead-zinc property with the acquisition of Glamis in 2006. The Peñasquito property is located in the northeast corner of Zacatecas state, Mexico. The elevation of the property averages 1,900 m (6,200 ft) above sea level. It is situated in a wide east-west valley. Minera Peñasquito, S.A. de C.V., wholly owned subsidiary of Goldcorp Inc. has operated twin SABC-flotation lines since June 2010. Each line is capable of processing 50,000 tonne per day using a SABC grinding circuit followed by flotation to produce lead and zinc concentrates. The addition of a Polysius Polycom HPGR 2417 with dual 3,000 kW drives to reduce the crushed pebbles produced by the SAG mills was planned to increase production to 65,000 tonne per day per line. The production has been limited to 100,000 tpd due to operating issues in the grinding circuit. The operating issue has been the amount of pebbles generated by the SAG mills is significantly less than originally planned. This paper describes the planned installation of a crushed augmented feed to maximize utilization of the HPGR capacity. This coupled with full utilization of the SAG and Ball Mill available energies there is the potential to achieve a 50% total capacity increase from the grinding circuit.

Jan 1, 2012

By K. A. Lewandowski

Binders have been suggested as an aid for agglomeration to improve copper recovery in heap leaching operations. However, it has not been established if the use of binders would negatively affect the solvent extraction process, which is used to purify the pregnant leach solution from the heaps and remove any contaminants. Such negative effects would lead to an increase in processing costs or a decreased in copper production. The controlled studies reported here have shown that some binders (a polyacrylamide and a waste treatment additive) did not interfere with the solvent extraction process. Other binders (a polyvinyl acetate emulsion and tall oil pitch) negatively impacted copper solvent extraction and, therefore, should not be used in copper heap leaching plants.

Jan 1, 2009

By Keros Cartwright

Sanitary landfilling has become one of the most widely used methods of disposing of solid refuse. A principal concern of regulatory agencies and the public itself is that landfill operations do not degrade the physical environment, including water resources, and the ground-water reservoir in particular. Ground-water and engineering geology can guide landfill operations into suitable terranes or develop measures to compensate for any natural limitations at a particular site Experience and research in Illinois suggest four activities relating to landfill disposal that warrant attention by geologists and engineers: (1) Regional delineation of favorable and unfavorable hydrogeologic conditions to facilitate planning and preliminary screening of potential landfill sites. (2) Site evaluations, with considerations of geologic materials, topography, water levels, flow systems, and local occurrence and use of water resources. (3) Re- search on aspects of the hydrogeologic environment that control effects of, or are modified by, landfills. (4) Formulation of practices in the siting, construction, and operation of landfills that prevent, mitigate, or isolate deleterious effects. The first two activities are basically in the domain of earth science, requiring the application of fundamental concepts of geology and hydrology and conventional site-exploration methods. The third activity, research, requires contributions from geology as well as other disciplines, including soil physics, sanitary engineering, and chemistry. The fourth calls for policy decisions by regulatory agencies and elected officials, using the contributions of scientists and engineers.

Jan 1, 1970

By M. Adnan Göksel

Pyrite cinder is generated by roasting pyrite for sulfur dioxide production. It contains up to 62% iron, but also may contain other hazardous or toxic materials such as Zn, Pb, As, T1, Cd, Cu, Sn and S. Furthermore, the physical characteristics are not properly suited for conventional sintering. As a result pyrite cinder is considered to be unsuitable for iron and steelmaking or for outside storage because of its potential for causing environmental problems. In recent years industrialized nations have put increasing pressure on the manufacturers to either use such waste products or properly dispose of them. In this study, solutions to both the iron recovery and disposal problem were attempted by pelletizing the pyrite fines with internal carbon. The pellets, after hydrothermal hardening, were reduced and melted in a furnace for hot metal production. Hot metal of usuable quality was produced and the hazardous materials were either collected with the fumes or in the slag.

Jan 1, 1984

By Joe Roby

Rolling disc cutters are the business end of hard rock and mixed face tunnel boring machines (TBMs). Since their first successful employment on a TBM over fifty years ago, disc cutter technology has constantly evolved, allowing modern TBMs to excavate very hard and abrasive rock efficiently. Disc cutters have also been employed successfully on earth pressure balance (EPB) and slurry machines, cutting rock under water and ground pressure. The range of materials excavated by machines today is broader, excavation rates higher and cutter costs lower than ever before, proving the value of investment in cutter development. This paper describes recent improvements in disc cutter components including cutter ring materials and processing, as well as improvements in lubricants, bearings, seals and cutter condition monitoring. These developments have resulted in more reliable cutters capable of operating in a wide range of geological conditions. Ultimately these improvements result in a better value for both contractors and project owners.

Jan 1, 2008

By Shular R. Scudamore

There was a time when heavy-duty apron feeders were built to last almost forever. The machines were heavy and built to maintain certain expected longevity and reliability. Increasing emphasis on return on capital leads to cost-effective designs. Costs can be increased or decreased, depending on customer specifications and the design philosophy of the feeder manufacturer. Specifiers can make important contributions to cost effectiveness. To do so, this article describes what should be known about planning with a supplier for heavy-duty apron feeders. There are several factors that should be considered, including capacity, characteristics of material carried, length, method of feeder loading, degree of lift, hopper opening, pan construction, and type of drive. Today's apron feeders are built in various sizes and with a variety of components to handle heavy, lumpy, or abrasive materials that can ruin lighter feeders. Careful feeder selection is important if it is to provide a controlled feed rate, absorb huge impacts, be used with long hopper openings, and have a relatively low power-perton capacity. Variations in systems and materials demand that each feeder be designed for its application, drawing on a wide range of components. Therefore, certain factors must be considered before final specifications are drawn. Capacity The design and application of an apron feeder is based on how material passes through a given system over the feeder into processing machinery. The processing machinery's capacity governs other equipment and productivity of the flow. From this basic information, related sizes of upstream equipment can be determined. Of these, the apron feeder acts as the "mouth and neck of the bottle." No more will pass than the mouth and neck will accommodate. Everything in the apron feeder design, from dimensions to power, is based on processing machinery. Material Considerations Are Vital Just as the nature of materials to be crushed or screened affects capacity and productivity of a crusher or a grinding mill, so does it affect capacity and performance of a feeder. Lump size must be identified closely so the pan width can be selected to accommodate the maximum lump with room to spare. For example, a lump size of 760 mm (30 in.) indicates a pan width of 1.5 m (60 in.) While two times the maximum lump is considered minimum width, if the maximum lump

Jan 12, 1983

By Helmut Westermayr, Michael Tergl

DESCRIPTION OF PROJECT Geographic Setting The Kops II plant is a pumped storage scheme of the hydroelectric power producer ‘Vorarlberger Illwerke AG’ which is currently under construction in the Austrian Province of Vorarlberg. The plant is located at the end of the Montafon valley and will be fed with water coming from the Silvretta mountain range (Figure 1) Description of Plant The Kops II plant shall be operated as a pumped storage plant with three highly flexible and quickly controllable power generating units. Each unit shall have a capacity of 150 MW and shall be equipped for both turbine operation and pump operation. The Kops II plant uses the existing Kops Lake as upper storage reservoir and the existing Rifa balancing reservoir as lower storage reservoir. All major plant components of the Kops II scheme are located below ground. Total investment costs areapprox. 360 million Euro. Construction Lots The construction works for the Kops II plant, which were subdivided into three lots, were launched in September 2004. It is planned that the first power generating unit shall go on line in the year 2007. The completion of the overall project and the operation start-up of the second and third unit are envisaged for the year 2008. Lot 1—Pressure Tunnel. The 5.5-km-long pressure tunnel forms the connection between the Kops Lake and the beginning of the pressure shaft. The tunnel was excavated by the use of a double-shield TBM. Lot 2—Pressure Shaft and Surge Chamber. The approx. 1.1-km-long pressure shaft was excavated by TBM, advancing from bottom to top. Featuring an inclination of80%, the pressure shaft overcomes a difference in height of approx. 700 m. Lot 3—Power House Cavern and Tailrace Structure. The power house cavern, which is being built approx. 150 m inside the mountain, forms the core of this plant. The power house is designed to accommodate three power generating units, and the transformer cavern is forseen to accommodate three transformer units. The tailrace structure serves the purpose of conveying the water to the lower storage reservoir during turbine operation and as water intake during pump operation (Figure 2).

Jan 1, 2007

By B. J. Vorster

Introduction The South African Iron and Steel Co. Ltd., in Sishen, operates a large iron ore mine in the Cape Province of the Republic of South Africa. The mine is about 600 km (370 miles) west of Johannesburg. Its annual capacity is 100 Mt (110 million st) of ore and waste. Present production is 60 Mt/a (66 million stpy). The mine operates continuously six days a week. Primary equipment includes 55 154 t (170 st) Wabco and Unit Rig trucks and 14 P&H shovels. During 1979, a feasibility study into the application of a trolley assist system was launched. This was due to the escalation in diesel fuel costs and the appeal by the South African government to reduce the use of fossil fuels. Tests and economic evaluations proved the system technically feasible. The estimated discounted cash flow return exceeded 50%. Diesel fuel consumption would be reduced by 120 ML (31.7 million gal) in the next 10 years. The construction of 7.7 km (4.8 miles) of line and the conversion of 66 154 t (170 st) trucks were completed in March 1982. System description The conventional 154 t (170 st) diesel electric rear-dump haul-truck is equipped with two direct current wheelmotors in the rear axle. They drive the rear wheels through planetary gearboxes. A 1.2-MV (1600-hp) diesel engine and an alternator is used to power the wheelmotors. The trolley assist system consists of an overhead power line, a current collector mounted on the truck, and add-on control equipment where external electric power is routed by way of the current collector to the motorized wheels. The diesel engine is used to propel the truck on level sections. On inclines, the wheel-motors of the truck are coupled by way of a current collector to the externally generated electrical power supply for propulsion. The diesel engine, having lower output than the wheelmotors, limits the truck performance. Previously, maximum output was required from an engine on inclines. By supplying the wheelmotors from a virtually unlimited outside electric energy source, the truck performance is enhanced to the extent that speed is increased by 46% and fuel consumption reduced by 75%. System design The unique operational requirements of this mine rendered the already proven trolley pole system useless. Minimum loss in truck mobility and flexibility was required. Overhead lines and substations were required to be relatively light and portable. This enables fast repositioning of a line with no loss in material. These unique specifications set the base for the design of the Sishen system. Steel I-beams, 203 x 203 mm x 52 kg/m (8 x 8 in. x 35 lb per ft) with lengths varying from 8.3 to 11.3 m (27 to 37 ft), mounted on base plates about 4 x 2.6 m (13 x 8.6 ft) were used as masts. The masts were erected at about 50 m (165 ft) and the base plates covered with about 12 t (13 st) of iron ore to keep them absolutely stable. Results from the pilot installations indicated that using single cantilever cross arms for insulator and overhead conductor suspension was not practical. The tension in the overhead varied too much with temperature changes, causing too much sag in the lines. There had to be a positive and negative conductor. It was decided to suspend each polarity on an independent cantilever and keep the conductors under constant tension by weights acting through a two-to-one pulley tensioning arrangement. For each overhead conductor, a standard 160-mm (6.5-sq in.) grooved copper railway conductor was used. To obtain the necessary current carrying capacity, two of these conductors are used in parallel per pole. Insulators are rated at 4 kV and are of the composite type. An 11-kV three-phase line, supported by the pantograph line masts on the opposite side of the dc line, feeds the rectifier stations. The rectifier stations consist of an 11-kV to 860-V, three-phase 1.46 MVA transformer and a three-phase diode bridge rectifier. The output voltage is 1200 V do earthed through a current limiting resistance network so that the line po-

Jan 4, 1986

By R. V. Ramani

Demands on available lands will continue to increase due to the projected increase in population and industrial expansion. Though there is an upper limit on the available lands, the multi-use nature of the lands will make it possible to meet these demands. However, this will not happen without adequate planning. Land uses can be broadly categorized as non-renewable and renewable. Lands with mineable resources can be dedicated at some point in time to the extraction of resources. Such a dedication, however long-term, is only temporary because of the non-renewable nature of the mineable resources. Implied here is that the land will be available before and after mining for other uses. Planning for such lands must have the objective that, as far as practicable, no non-renewable uses are pre-empted and no renewable uses are permanently destroyed. The primary aspects of this planning process will be addressed in this paper, These aspects include a discussion of planning responsibility, data needs and availability, the integration of mine planning and post-mining land use planning and a long-term plan for resource conservation and utilization. Minerals, together with agriculture and forestry products, are the primary sources of wealth. Therefore, to avoid land development that may pre-empt future mineral resource utilization, the local planning groups must be aware of the mineralization and mining potential. Much work needs to be done to identify and characterize the mineral resources. Even more work is needed in land use planning for lands with mineral deposits.

Jan 1, 1982

By S. Frimpong

Cable shovel requires continuous monitoring through excavation to achieve reliability, longevity and economic usage. The operating environment and the stress and deformation fields on the front-end assembly must continually be monitored to avoid random fatigue failure. In this paper, the authors advance frontiers of cable shovel reliability through real-time stress and deformation monitoring during excavation. Cable shovel boom stress and deformation analysis are developed using a combination of flexible and rigid body approach. A virtual prototype is developed to simulate the cable shovel excavation in oil sands and to examine the motion, stress and local deformation of the boom. A numerical example is used examine cable shovel boom durability using stress and deformation fields simulation. The results show that stress and deformation are large around the joint between the upper body and the boom. The simulation of the effect of material properties on boom deformation shows that the deformation is larger in hard formation than in soft formation. The study provides a solid foundation for further study of failure life analysis of the cable shovel components.

Jan 1, 2006

By S. Noll

Ventilation is an essential part of any underground mining operation. It provides fresh air for workers and machinery, keeps up an adequate mine climate and dilutes and dissipates noxious gases. Possible changes in the economic environment for mining in the future, e.g. increasing energy costs, will necessitate optimization of distribution of airflow within most mines. This paper discusses the scientific set-up for measurements as well as the behavior and influence of parameters of ventilation according to airflow distribution under consideration of technically possible set-ups of mine fans. This study was done in an underground mine with a flat seam room and pillar mining method.

Feb 27, 2013

By D. Earley

High metal prices and new world trade standards and accounting for environmental liability in financial disclosures are creating markets for metals commodities that are produced using ?green technologies?. A promising "green" gold leaching system uses a polysulfide based lixiviant which is non-toxic and non-polluting. Laboratory testing has demonstrated selective gold extraction rates comparable to those of cyanide. The polysulfide lixiviant is a dilute aqueous solution which can be inexpensively produced from readily available chemical reagents and even mining wastes. The reagent system is self-buffering and maintains the optimal chemical environment for leaching. Treatment of residual leach solutions is not necessary because the lixiviant itself is not toxic, and breaks down as the system equilibrates. Simple closed system boiling is used to recover gold from process solutions. The polysulfide lixiviant can then be readily renewed and recycled back into the system, forming a closed loop system that conserves reagents and energy which minimizes operating costs. Economic projections have shown that the system can be used profitably for standard ore types and grades.

Jan 1, 2009

By Ray Hutton, Darrell Liebno, Taro Nonaka

Background Population growth and increasingly stringent regulatory controls on water quality across North America have resulted in municipal governments investing heavily in infrastructure to control what are known as Combined Sewer Overflows (CSOs).These are events which occur when combined sewers exceed their conveyance capacity during periods of heavy rainfall or snowmelt. The city of Atlanta, Georgia is one such municipality; with a population of over450,000 within city limits and a sewer system servicing 1.2 million including adjacent jurisdictions, the City of Atlanta has a Combined Sewer System (CSS) encompassing approximately 15% of its total 3,540 km (2,200 miles) of sewers. Atlanta’s CSO discharges to local watercourses began to draw fire from environmental groups in the1980s. As a result, in the early 1990s, the City constructed a series of CSO control facilities which provided screening and chlorination at seven CSO discharge points across the CSS watershed. Unfortunately, these facilities were not capable of handling all of the overflows generated due to heavy storm events; frequently, untreated water was bypassed around the treatment facilities. The federal Environmental Protection Agency (EPA) deemed that water quality standards were being violated by these discharges, and a suit was brought against the City to force a higher standard of compliance. As a result, the City entered into a federal Consent Decree which would bring CSOs into compliance with federal standards by 2007. A critical component of this plan was the design and construction of the West Area CSO Tunnels and Pumping Station. In February 2003 the City’s Department of Watershed Management retained the services of Jordan Jones & Goulding/Hatch Mott MacDonald/Delon Hampton Associates (JDH Joint Venture) to design and provide construction management ser-vices for the project, which was designed to capture combined sewage from three of the City’s existing CSO facilities on the northern end of the CSS watershed. The design consisted of two connected tunnels which would convey the wastewater originating from the North Avenue, Clear Creek, and Tanyard Creek CSO facilities to a submersible wet well pumping station located at the R.M. Clayton Water Reclamation Center (WRC). Since the majority of the effluent stream consisted of storm water, the City elected to design and construct a separate treatment plant. This plant was designed under a separate contract, and is currently under construction.

Jan 1, 2007

By F. Freme

Coal production in the United States reached a record level in 2005, ending the year at 1.03 Gt (1,133.3 million st) according to preliminary data from the U.S. Energy Information Administration (Table 1). Production in 2005 was 19.2 Mt (21.2 million st) higher than the 2004 level of 1 Gt (1,112.1 million st) and surpassed the prior record set in 2001 by 5.1 Mt (5.6 million st). Although total U.S. coal consumption rose in 2005, not all coal-consuming sectors had increased consumption for the year. Coal consumption increased in the electric power sector by 2.2 percent and declined in the other industrial sector, while coking coal consumption decreased slightly.

Jan 1, 2006

Gangue-cemented paste backfill (GCPB), is a well-established green mining technology and significantly improves the recovery rate of mineral resources, prevents mine dynamic disasters, reduces surface subsidence, and consumes a considerable amount of solid waste. The addition of an early strength agent as an additive in cement-based materials provides several security, technical, and economic advantages. In this study, the early strength agent on the early age (3, 7 and 28 days) strength of GCPB is evaluated experimentally. The GCPB specimens have an initial sodium sulfate early strength agent concentration of 0%, 1%, 2%, 3%, and 4%, and the obtained samples were analyzed by testing for uniaxial compressive strength (UCS) and scanning electron microscopy (SEM). The test results show that the UCS of the GCPB specimens with sodium sulfate is much higher than that of the blank specimens. When cured for 3 days and 7 days, the strength of GCPB with 2% sodium sulfate increased the most, by 131% and 116% respectively. When cured for 28 days, the strength of GCPB with 1% sodium sulfate increased by 135%. Scanning electron microscopy (SEM) results showed that the GCPB with 1% and 2% sodium sulfate had better internal structure compactness, thicker acicular crystals, and more flocs. As a kind of early strength agent, sodium sulfate can react with calcium hydroxide to generate calcium dihydrate sulfate and then react with calcium aluminate; the hydration product (C3A) quickly generates calcium sulfoaluminate hydrate (AFt) needle-shaped crystals, forming an early skeleton and improving the early strength.

Jan 7, 2020