Search Documents

By W. P. Nel

A fuel cell is an electrochemical engine that converts the chemical energy of a fuel, such as hydrogen, and an oxidant, such as oxygen, directly into electricity. The emerging fuel cell industry may represent a major opportunity for the global platinum mining industry. This is because low temperature fuel cell systems use platinum group metals as catalysts. Fuel cell vehicles may become the most important driver of future platinum demand within years of their commercialization. A great number of factors impact on and drive the diffusion of fuel cell vehicle innovation. Such drivers range from energy security to environmental concerns and the technological development of fuel cells and systems. Such factors and drivers of fuel cell vehicle diffusion are combined with the generic ?body of knowledge? on ?technology forecasting? and ?diffusion of innovation? to design a framework that provides a holistic approach to the analysis of this complex enterprise. An attempt is made in this paper to address the following questions: Which types of fuel cells require platinum group metals? Which types of fuel cells will achieve dominant design status? Will fuel cell vehicles diffuse successfully? How big will the impact of successful fuel cell vehicle diffusion be on future platinum demand? How well do fuel cell vehicles compete with incumbent technologies such as spark-ignited and compression-ignited internal combustion engine-driven vehicles? How soon will oil depletion start to drive the diffusion of fuel cell vehicles? How important is hydrogen as a fuel? What impact does the inadequate hydrogen fuelling infrastructure have on fuel cell vehicle diffusion? The paper contains some initial results of a research project that has the aim of producing a schedule of future platinum demand generated from fuel cell vehicles. Keywords: diffusion of fuel cell vehicles, technology forecasting, platinum demand forecasting.

Jan 1, 2004

By R. K. Brummer

A simplified two-dimensional plane strain numerical technique for the non- linear modelling of a tabular mining excavation in brittle host rock under high stress conditions is described. The model has been developed using relatively straightforward assumptions based on extensive underground investigation of the fracturing and deformation of rock at the stope face in deep gold mines on the Witwatersrand, together with observed rock behaviour under laboratory conditions. The reef rock is modelled as a linear string of yielding elements which interact horizontally, while the elastic rockmass remote from the reef is modelled using boundary element techniques. This elementary technique is shown to produce results which agree closely with the observed behaviour of the fractured rock during the mining of a remnant pillar

Jan 1, 1987

By H. L. Zimba

Flotation involves the selective levitation of mineral and its transfer from cell to launder. The flotation rate is the rate of this transfer. It may be defined by the slope of a recovery-time curve for any cell in a bank or at any time in a batch operation. The objective in flotation rate study is an equation expressing the rate in terms of some measurable property of the pulp. This can be either the concentration of floatable mineral in weight per unit volume or a relative concentration, which will be a function of the recovery. A rate equation for an actual flotation pulp will contain at least two constants, both to be determined from the collected data. The data used in this paper were collected from bench-scale flotation tests on Konkola primary mill cyclone overflow at various pulp densities and pre-flotation thickener underflow at a pulp density of 35% solids by weight.

Jan 1, 2009

By M. Kumral, S. Hmoud

Optimising the configuration of infill drill holes is an important step during mineral exploration campaigns. However, this optimisation process encompassing all possible drilling configurations within a mineral deposit is highly combinatorial and hard to solve in a reasonable time. This paper proposes using spatial clustering algorithms to divide the orebody into contiguous zones and target the best zones with infill drilling in order to reduce the size of this optimisation problem. Several clustering algorithms are assessed in a spatial context on hypothetical datasets. This evaluation shows that the hierarchical density-based spatial clustering application with noise (HDBSCAN) algorithm can be used in combination with the uniform manifold approximation and projection (UMAP) dimensionality reduction algorithm to identify contiguous zones in the orebody.

Sep 1, 2021

By Y. C. Kim

The estimation of local recoverable reserves using the widely spaced exploration drill hole information in an open-pit mine is probably one of the most difficult tasks in ore reserve estimation. The difficulty of this problem is magnified if the grade distribution is highly skewed, such as in a gold deposit. This paper describes the results of performance comparison of three different kriging techniques in an open-pit gold - silver deposit. The three different kriging techniques compared in their local recoverable reserve estimation capabilities are: (1) lognormal kriging, (2) indicator kriging, and (3) probability kriging. For performance comparison, the predictions are compared with the actual recoverable reserves determined from blast hole information. Based on the results from one test bench, both indicator and probability kriging performed better than lognormal kriging, perhaps owing to samples not being truly lognormal. Between indicator and probability kriging, probability kriging results were definitely superior to indicator kriging results.

Jan 1, 1987

By B. P. Watson

In South Africa, the Bushveld platinum group metal deposits are unique in that they are the largest platinum group metal deposits in the world. These deposits occur as two distinct stratiform tabular orebodies and strike for many hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2 000 m. The mining method is a variation of planar open stoping. Pillars are widely used to support the open stopes. Crush pillars are commonly used in this role, where the residual pillar strength provides the required support resistance to stabilize the stoping excavations. This paper describes the direct measurement of stress within these crush pillars, and describes the stress?strain behaviour of these pillars. These findings indicate that the measured pillar failure stress is too high. The implications of these findings are that roof damage and pillar bursting could occur, and some examples of this type of damage are shown. The paper concludes that this problem could be mitigated if the three dimensional pillar geometry were modified and the pillars were cut smaller.

Jan 1, 2007

By A. Hoogervorst

Cyanide is a key contributor to the efficiency of gold extraction. Public perceptions of cyanide are emotive and following some publicised incidents involving cyanide, the gold mining industry established a voluntary cyanide code for the manufacture, transport and use of cyanide in the production of gold. The paper describes the development of the code, its content and the third party auditing of the code as a means of establishing and maintaining benchmark standards. In adhering to the cyanide code requirements, there are overlaps with other management systems such as ISO 14001 and OHASA 18001 and the paper seeks to show how existing mine systems can readily accommodate cyanide code compliance and that operating and auditing the cyanide code can assist in the integration of mine heath, safety and environmental management systems.

Jan 1, 2009

Anglo Platinum is in the process of introducing a number of initiatives, varied in nature, on a scale that will impact operations in the short, medium and long-term. The advent of mechanization on a large scale and the introduction of new mining technologies therefore require a different approach to the design of ventilation and cooling systems. In addition, the ventilation and cooling systems serving increasingly deeper operations will place a greater demand on electrical power consumption?this in an environment where power generation is limited and increasingly expensive. Ventilation and cooling systems currently being employed in platinum operations have evolved from practices first pioneered in deep level gold mines. However, in modern and future platinum mines, deepening of operations will take place in a somewhat different environment?particularly in terms of geothermal settings and electrical power utilization. This provides the opportunities to devise novel and energy-efficient ventilation and cooling strategies tailor-made to meet these challenges. The need for refrigeration and cooling at depth will increase the capital and operational cost component of ventilation systems and the medium-term limitations on the availability of electrical power will require the provision of innovative systems. The increased use of diesel-powered vehicles underground, the viability of energy recovery and feasibility of thermal storage opportunities are discussed in this paper. Some of the challenges and the solutions currently proposed in terms of ventilation system design, refrigeration plant selection and chilled water distribution methodologies are described. Changes in strategies core to this discipline that affect the health and safety of employees and the profitability of modern operations are deemed necessary to support the transformations that are envisaged.

Jan 1, 2008

By C. Van Rhee

In dredging practice sand is eroded at very high flow velocities using water jets. The existing pick-up functions overestimate erosion. By taking the permeability into account conventional pick-up functions can be made suitable for high velocity erosion. This can be achieved by modifying the critical Shields parameter. The procedure is demonstrated using the pick-up function of Van Rijn. The theory is compared with experiments and agreement is good.

Jan 1, 2007

By M. Solomon

During the course of 2011 the nationalization of mines emerged as one of the most contentious and emotive political issues under review. Some four years after the African National Congress electoral conference held in Polokwane, which had led to a change of leadership within the country's ruling party, elements within the ruling party's youth league, which had been virulently supportive of the change in leadership, turned on the incumbent President, using the mining question as its rallying call. At issue was the expressed perception that mining has, since the country's democratization, not delivered the anticipated benefits to the population as a whole, continues to be the preserve of the capitalist element of the South African community, and is therefore in need of radical reform. Aspersions were made that transformation within the industry had failed dismally and that mining companies had not delivered against their commitments to the Mining Charter and social and labour plans. The debate became extremely vocal and heated, evoked dramatic and emotive opinions, and vigorous skirmishes on the matter were fought in the media over much of 2011 and into 2012.

Jan 1, 2013

By C. G. Verkerk

The paper discusses the transport and rheological characteristics of high concentration slurries or pastes for backfill purposes. The influence of pipe size, particle size distribution, additives, coarse material and mass concentration on these characteristics is addressed.

Jan 1, 1988

By Z-P. Song, Z-B. Jiang, A-N. Jiang

"In deep excavations under conditions of high ground stress, even hard rock undergoes creep and other time-dependent effects that may result in instability. This study involves an analysis of the typical damage to the surrounding rock in the deep tunnels of the Jinchuan nickel mine in China. In order to understand the creep mechanism, triaxial creep laboratory tests were conducted under high stress. The creep characteristic curves and the Nishihara model parameters of typical rock were obtained from these tests. The numerical simulations, with which the creep model is developed, were performed using Flac3D. The creep model parameters were back-analysed on the basis of field monitoring data. Finally, appropriate support schemes for deep tunnels are suggested. The creep deformation of rock increases with time and axial load. At the same load level, the creep deformation of unloading is greater than that of loading. The simulated deformations of the surrounding rock are coincident with those from in situ monitoring, indicating the applicability of the presented rock creep model in situations of high ground stress. The results constitute a reference for support design in deep mining tunnels.IntroductionThe excavation of underground caverns can alter the natural stress field of the surrounding rock. In deep engineering projects under conditions of high ground stress, even hard rock shows obvious creep properties and time effects (Yao, 2005; Liu, 1994). The time effect of excavation not only causes decompression of the floor and increases sidewall stress, but also leads to stress concentration at the corners of the excavation, which influences the stability of the surrounding rock in a very complex manner.Many researchers have studied the creep properties of rock. ‘Griggs (1939) showed that creep occurs in sandstone, shale, and silty sandstone rock under the load of 12.5%–80% of the failure load.’ Subsequently, much research has been published on rock creep tests, including the uniaxial compressive creep test, the triaxial compressive creep test, the discontinuity rock shearing test, and field tests (Wawersik, 1974; Amadei et al., 1980; Okubo et al., 1991; Jin et al.,1995). A rheological model is used to describe the complex rheological deformation of material. This model is based on various fundamental parameters including rock elasticity, plasticity, and viscous properties, which can be combined into a constitutive model to reflect the rheological properties of various types of rocks. Wang et al. (2014) studied the creep– damage–rupture characteristics of rock salt by applying a creep-damage model. Munson (1997) developed a multi-mechanism constitutive model of creep of polycrystalline rock salt based on steady-state creep and modified it to incorporate transient creep through work hardening and recovery. An elasto-viscoplastic approach was developed to simulate the timedependent nature of the fracture zone (Malan, 1999). Rheological models were proposed to understand the collapse of iron ore mines in Lorraine by Dragan et al. (2003)."

Jan 1, 2016

By Y. H. Hatzor

ABSTRACT: A fully dynamic, two dimensional, stability analysis of a highly discontinuous rock slope is demonstrated in this paper. The studied rock slope is the upper terrace of King Herod’s Palace in Masada, situated on the western margins of the seismically active Dead Sea Rift. The dynamic deformation of the slope is calculated using a fully dynamic version of DDA in which time dependent acceleration is used as input. The analytically determined failure modes of critical keyblocks in the jointed rock slope are clearly predicted by DDA at the end of the dynamic calculation. It is found however that for realistic displacement estimates some amount of energy dissipation must be introduced into the otherwise fully elastic, un-damped, DDA formulation. Comparison of predicted damage with actual slope performance over historic time span window of 2000 years allows us to conclude that introduction of 2% kinetic damping should suffice for realistic damage predictions. This conclusion is in agreement with recent results of Tsesarsky, Hatzor and Sitar (2002) who compared displacements of a single block on an inclined plane subjected to dynamic loading obtained by DDA and by shaking table experiments. Using dynamic DDA it is shown that introduction of a simple rock bolting pattern completely stabilizes the slope. RÉSUMÉ : On présente dans cet article une analyse bidimensionnelle complète de la stabilité d’une pente rocheuse très fracturée. La pente rocheuse étudiée est la terrasse supérieure du Palais du roi Hérode à Massada, située sur la rive Ouest du Rift sismiquement actif de la Mer Morte. La pente est constituée de blocs de dolomite raide présentant une stratification sub-horizontale et des joints sub-verticaux. La déformation dynamique de la pente est calculée en utilisant une version entièrement dynamique de l’Analyse de Déformation Discontinue (DDA) où l’accélération dépendant du temps est utilisée comme donnée. Les modes de rupture déterminés analytiquement des blocs clés dans la pente rocheuse fracturée sont clairement prévus par l’approche DDA à la fin du calcul dynamique. On trouve cependant, que pour obtenir des estimations réalistes du déplacement, il faut introduire un facteur de dissipation énergétique sans lequel la formulation DDA serait totalement élastique et sans amortissement. En comparant l’endommagement prévu avec les caractéristiques de la pente sur une période historique de 2000 ans, nous pouvons conclure que l’introduction d’un amortissement cinématique de 2% suffit pour obtenir de prévisions réalistes. Cette conclusion est conforme aux résultats récents de Tsesarsky, Hatzor and Sitar (2002) qui ont comparé les déplacements d’un bloc isolé sur un plan incliné sous chargement dynamique obtenus avec l’analyse DDA et à partir d’essais sur table vibrante. ZUSAMMENFASSUNG: En utilisant une modélisation DDA dynamique on montre que l’introduction d’un système simple de boulonnage stabilise la pente.In dieser Veroeffentlichung wird eine vollstaendig dynamische, zweidimensionale Stabilitaetsanalyse eines hoechst diskontinuierlichen Steinhangs dargestellt. Der untersuchte Hang ist die obere Terrasse des Herodespalastes in Massada, welche in den westlichen Randgebieten des seismisch aktiven Toten Meer Grabens liegt.Die dynamische Deformation des Berghangs wird mit Hilfe einer vollstaendig dynamischen DDA-Version berechnet, in welcher als Input die zeitabhaengige Beschleunigung eingegeben wird. Die analytisch bestimmten Versagensarten kritischer Schluesselbloecke in diesem zerkluefteten Steinhang werden durch Anwendung von DDA am Ende der dynamischen Berechnung klar vorausgesagt. Es zeigt sich jedoch, dass fuer realistische Dislozierungs-Abschaetzungen ein gewisses Mass an Energieverlust in der sonst vollstaendig elastischen, ungedaempften DDA-Fassung einbezogen werden muss. Der Vergleich des vorhergesagten Schadens mit dem aktuellen Verhalten des Berghangs waehrend einer historischen Zeitspanne von 2000 Jahren erlaubt uns zu schliessen, dass ein Zusatz von 2% kinetischer Daempfung fuer eine realistische Vorhersage des Schadens ausreichen sollte. Diese Schlussfolgerung steht im Einvernehmen mit neuen Ergebnissen von Tsesarsky, Hatzor und Sitar (2002), welche die Dislozierung eines einzelnen Blocks auf geneigter Ebene unter dynamischer Belastung – unter Anwendung von DDA und “shaking table”-Versuchen – verglichen. Mit Hilfe der dynamischen DDA wird gezeigt, dass der Steinhang durch Anwendung einer einfachen Steinschraubenstruktur vollkommen stabilisiert werden kann.

Jan 1, 2003

By L. P. Fatti

An important feature affecting the classification of a remotely sensed scene is that the data are, in general, spatially correlated. Various approaches are discussed towards incorporating the correlation between neighbouring pixels when they are classified on the basis of their spectral reflectance data.

Jan 1, 1987

By P. Otto, G. Borm, Th. Dickmann, F. Amberg, R. Giese

Based on many years experience, the well proven Swiss Tunnel Seismic Prediction System TSP has been substantially augmented for online geological prognosis in underground construction. In its latest version, the Integrated Seismic Imaging System ISIS provides high resolution seismic images of the rock mass around a tunnel face via an array of standard anchor rods. These rods contain 3D-geophones at their tips and can be readily installed during excavation work. A further innovative component of the system is the newly developed high-power repetitive source for application in hard rock: a pneumatic hammer with laser triggering to be mounted on construction machinery. A user-friendly software package permits online data acquisition and processing, 3D-visualization, and a first geological interpretation. Tomographic images of compressional and shear wave velocity fields at fault zones in metamorphic rock of the Gotthard Base Tunnel in the Central Alps are presented. Das langjährig bewährte Schweizer Tunnelseismische Vorauserkundungssystem TSP wurde inzwischen wesentlich weiterentwickelt. In seiner neuen Version, dem Integrierten Seismischen Imaging System ISIS, ermöglicht es hochauflösende seismische Abbildungen des Gebirges im Vorfeld und Umfeld einer Tunnelauffahrung mit Hilfe einer Anordnung von Felsankern, die an ihren Spitzen 3-Komponenten-Geophone enthalten. Eine weitere Neuerung von ISIS ist die pneumatische Hochleistungs-Impulsquelle mit Laser-Triggering. Eine benutzerfreundliche, interaktive Software ermöglicht die online Datenerfassung und -auswertung, 3D-Visualisierung und eine erste geologische Interpretation. Tomografische Abbildungen von Kompressions- und Scherwellengeschwindigkeitsfeldern an Störungszonen in metamorphem Gestein des Gotthard-Basistunnels werden gezeigt. Basé sur de nombreuses années d’expérience, le système suisse, bien établit, de reconnaissance sismique à l’avancement des tunnels (système TSP), a été sensiblement amélioré pour obtenir une prévision géologique en temps réel durant l’avancement de travaux souterrains. Sa dernière version, le Système Intégré d’Imagerie Sismique (ISIS), fournit des images sismiques haute-résolution du massif rocheux à l’avant d’un tunnel grâce à un réseau de tiges d’ancrage standard. Ces tiges, équipées à leur extrémité de géophones 3 composantes, s’installent très aisément durant les travaux d’excavation habituels. Le élément d’innovation récente concern le nouvelle source très répétitive et de forte puissance pour les applications aux roches dures: un marteau pneumatique déclenché par un système à laser. Un ensemble de programmes informatiques convivial permet l’acquisition et le traitement en temps réel des signaux et produit une vue 3D ainsi qu’une première interprétation géologique. Nous présenterons des images de réflexion d’ondes de compression et de cisaillement ainsi que des inversions tomographiques de zones de faille dans des terrains métamorphiques obtenues à l’occasion du creusement du tunnel de base du Gothard, dans les alpes centrales.

Jan 1, 2003

By S. C. Greeff

At ISCOR the quantitative determination of the structural properties of coke is done with a Leitz-TAS Image Analysis System. A reflected light microscopic image of a coke sample is converted into a binary image and stored in computer memory or on hard disc. By means of mathematical and stereological techniques the system can transform the images electronically. A lightpen can be used to determine the sequence of these operations. TASIC, which is based on BASIC language, is used as the program language on the computer. The majority of the programs are written by the user to ensure satisfactory results for specific studies. The computer controls the whole system, including the movement of the microscope stage, focusing, transformation and measurement of the image and data processing. The computer is also applied for establishing statistical correlations between the structural and other coke and coal parameters as well as for graphics and predictions of the coke structure. Factors affecting the structural properties of coke are discussed and conclusions are drawn.

Jan 1, 1987

By A. Madowe

This paper discusses the mine planning process for Letseng diamond mine in the Kingdom of Lesotho, in conjunction with the various software packages used during the process. The major pillars of the long-term mine planning process at Letseng are pit optimization followed by pit design and scheduling. Letseng uses Gemcom Whittle and GEMS for pit optimization and design and Runge XPAC for scheduling. The output of the mine planning process results in the generation of published mineral reserves and provides input into the Letseng overall business plan. The process of defining the key inputs for the entire mine planning process is discussed, which covers: ? Pit optimization ? Slope design as an input ? Diamond price inputs ? Operating and capital cost inputs ? Haul road design ? Generation of pit shells ? Selection of an optimum pit shell and interim cutbacks using operational scenarios ? Sensitivity analysis on the selected optimum pit shell. ? Pit design ? Slope design criteria in the detailed design ? Split shell vs concentric pit design ? Practical mining widths to determine cutback design ? Ramp design ? Pit design process in the GEMS software package. ? Detailed scheduling ? Development of scheduling scenarios in the XPAC software package ? Planning through mining production bottlenecks. ? Company-level NPV model ? Comparing scenarios and input of the different schedule scenarios into the company NPV model. Keywords pit optimisation, mine planning, pit shell, recovery, dilution, revenue factor, pit design, split shell, sensitivity analysis, scheduling, production bottleneck, NPV, discounted cashflow.

Jul 1, 2013

By K. Bryan, O&apos

A 10-year program to integrate crushing and screening models into daily flowsheet design practice has proven successful. A Circuit Analysis Program (CAP) is used worldwide to design and evaluate new and existing crushing flowsheets. To gain user acceptance of CAP and maximize effectiveness, model development, simulation flexibility, ease of use, and developing international access are key issues. These issues have been resolved effectively resulting in flowsheet simulations to assist in justifying increased capital investment. CAP is presently utilized in Canada, United States, and South Africa with intentions to expand to Europe and Asia.

Jan 1, 1987

By C. M. Suhr

n order to validate the borehole analysis valuation procedure commonly used in the South African gold mining industry, a simulated orebody was used to create borehole values which would serve as data for the procedure. After confirming the distribution, calculating the variance size of area relationship, estimating the block variance, and calculating a profit measurement for each set, comparisons were made to the known population parameters. Results show only one overall bias (in the estimation of the lognormal third parameter), which is carried throughout the analysis. The remainder of the analysis is unbiased, validating the procedure.

Jan 1, 1987

By C. Kirmanli

The purpose of this paper is to develop an expert system for hydraulic excavator and truck selection in surface mining. Hydraulic excavators and trucks are finding increasing applications in mining operations. Hydraulic excavators are extensively used especially when bringing electricity to rural areas is difficult and for small-scale mining. This paper describes an expert system, which selects the optimum hydraulic excavator truck configuration such that unit production cost is minimized and technical constraints such as geological, geotechnical and mining constraints are satisfied. The system has four modules: user interface, rules and an methods, databases and output module. The expert system in this study is developed within KappaPC shell. It supports object-orientated technology for the MS Windows environment. The software provides a very useful tool to practitioners, saving time and cost. Equipment selection is a recurring and expensive problem of mine planning and often involves interdisciplinary experts from different fields. It is very difficult and expensive to bring together all these experts. The capabilities of the expert system developed are illustrated in the paper. The software overcomes the difficulties of selecting the proper equipment for surface mining operations, which is very important, and results in substantial savings. Equipment databases for hydraulic excavators with 15-59 yd3 capacities and trucks with 35-360 tons are constructed and these databases are used to select the proper configuration. A case study is carried out for Soma Surface Coal mines in Turkey. Keywords: surface mining, expert systems, equipment selection, hydraulic excavators, diggability

Jan 1, 2009