Search Documents

By J. Brad Seymour, Mark K. Larson, Richard L. Rains, Douglas R. Tesarik

For several years, researchers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) have been using geotechnical instruments in underground mines to study ground control problems and develop means of reducing accidents and fatalities caused by ground falls. This paper describes many of the different types of instruments, sensors, and data acquisition equipment that have been used for these studies; briefly explains the advantages and disadvantages of various sensor technologies; provides practical recommendations regarding the use of specific instruments and data acquisition systems; and outlines a general approach to the design and implementation of a successful instrumentation plan. A wide variety of instruments are commercially available for measuring deformation, strain, stress, and/or load. If used correctly, these instruments can provide important quantitative information regarding the mining-induced behavior of the host rock, the performance of ground support systems, and the safety and stability of underground workings. Data collected from these instruments can warn mine staff of impending ground control failures or hazardous working conditions, as well as provide valuable information for the design of ground support systems and the configuration and sequencing of mining excavations. We hope that the practical information presented in this paper will encourage a more widespread use of geotechnical instruments in underground mines and lead to reliable measurements that aid the engineering decisions affecting the safety of miners.

Jan 10, 2000

Detect fires in or near mine shafts, isolate smoke filled areas, and remotely extinguish fire. Approach A system (of sensors, automatic alarms, an aboveground control console, remotely operated ventilation doors, and sprinklers) has been built from off the-shelf components, and fire, tested in two mines. How It Works The system uses three different kinds of sensors that can detect the heat or smoke of a fire and automatically actuate alarms. When the alarm sounds in the control center on the surface, water sprays in the mine shaft and shaft station areas can be remotely turned on to deluge both the inside and the outside of the mine shaft's wooden support structure. To protect miners from toxic fumes, smoke control doors can be closed or opened, either remotely from the control center or directly by miners using the manual or electrical actuators at the door locations. Man doors built into each ventilation door allow persons to pass without opening the main door.

Jan 1, 1977

By C. H. Elder

An experimental degasification program using a vertical borehole and vacuum pump to drain gas from the gob area of a longwall panel was successful at Bethlehem Mines Corporation, Cambria Division, No. 33 coal mine. Sixty-one million cubic feet of methane has been exhausted during a 9-month period. Daily production time in the panel increased as a result of lower methane levels in the returns. Removal of large quantities of methane in this way and the exclusion of it from the ventilating system will provide reduced cost in mine ventilation and provide a safer environment for the mine.

May 1, 1969

By Robert A. Jankowski

Through laboratory and underground studies, the Bureau of Mines has evaluated the use of passive barriers (dust shields) to help confine dust generated by longwall shearers to the face area. Laboratory studies focused first on selection of the optimum barrier design, which proved to be a simple, gobside barrier (made of conveyor belting), coupled with a headgate splitter arm, which was found necessary to prevent the dust cloud from entering the walkway at the headgate end of the shearer when cutting tail to head. Further laboratory testing was done to determine whether using passive barriers in combination with different water-spray dust-reduction methods, including the shearer-clearer system developed by the Bureau, would improve dust reduction over that from using the water sprays alone. It was found that the combination of gobs ide passive barriers plus the full shearer-clearer system was most effective, and surmised that this would be especially useful in thicker seams. However, underground testing revealed that the shearer-clearer system alone was 35 pct more effective in reducing dust contamination than when used with the gobside passive barriers, and far more effective than using passive barriers with a conventional water spray system. For such an effective system as the shearer-clearer; the reduction in avail-able space over the top of the machine actually impeded system performance; this was shom1 in both eastern and western mines. But when used with comparatively inefficient water spray systems, the passive barriers, used in combination with a headgate splitter arm, provide consider-able help in reducing dust levels in the walkway.

Jan 1, 1986

By David C. Oyler, Gregory Hasenfus, Gregory M. Molinda

Few studies have specifically measured and documented the large-scale loading behavior and durability of ventilation stoppings to mining induced movements, particularly from longwalls. Ventilation stoppings are more commonly the concern of ventilation engineers, and ventilation stopping response to ground movement has only been documented in an incidental manner. This paper presents the investigations of underground measurements that have been conducted to determine the loading response of stoppings constructed from lightweight aggregate concrete masonry units (CMU). These investigations have produced some interesting results that may prove beneficial, not only for developing and assessing alternative stopping construction techniques, but also for designing and selecting standard construction methods for use in varying mining conditions. For instance, the interface friction that results from wedging a CMU stopping during construction plays a substantial role in its ability to resist both lateral and vertical loads. Although they are not intended for ground support, the study showed that block stoppings can resist vertical loads of at least 2,700 to 3,000 kN. Asymmetric loading of a stopping may result in localized failure of blocks within a stopping, which, depending on the severity, can be a precursor of impending stopping failure. In addition to measurement results and implications, the paper will also present details of field measurement methods used to assess stopping response. Stopping stiffness and material strength characteristics will also be presented.

By J. P. Morris

This paper describes a gas-transport method for measuring vapor pressures of liquid metals. Vapor pressures of iron and nickel were determined at temperatures between 1,540° and 1,620° C. The results can be represented by the following equations: log Pmm (iron) -19,460/T + 9.147, log Pmm (nickel) -2l,030/T + 9.689. The study was undertaken as part of a program to determine thermodynamic activities in liquid iron alloys.

Jan 1, 1957

By R. Barany

This paper reports determinations of heats of formation (from the oxides and elements) of crystalline cadmium metasilicate and crystalline lead meta-silicate by hydrofluoric acid solution calorimetry. The results, in conjunction with known entropy values, yield free energies of formation. There are no earlier data of this type for cadmium metasilicate. The results of this investigation for lead metasilicate deviate from the literature values (which are less reliable) in the direction of increased thermodynamic stability. Both cadmium and lead metasilicate are much less thermodynamically stable with respect to their constituent oxides than are the corresponding compounds of the alkaline earth metals.

Jan 1, 1959

By E. J. Kloos

Two self-contained breathing apparatus of the closed-circuit compressed-oxygen type were evaluated for performance at 32° to -25° F. Low-temperature effects of oxygen and carbon dioxide concentration, visual properties of the facepiece, and mechanical operation of the apparatus were studied. Although operation varied with the wearer, his breathing rate, the apparatus precooling time, and the temperature, results suggest that general use of currently approved compressed-oxygen closed-circuit breathing apparatus be limited to temperatures above 32° F.

Jan 1, 1968

By P. W. Jeran, M. C. Irani, D. H. Lawhead

The methane emissions from an advancing coal mine section were continuously monitored for 120 days. During this time, the section advanced 2,000 feet into virgin Pittsburgh coalbed producing 54,565 tons of coal with a total methane emission of 91 million ft3. Analysis of the data gathered showed that daily methane emissions did not correlate with overburden thickness and daily coal production. A good correlation was found between the daily methane emission and the average length of rib exposed to virgin coal.

Jan 1, 1976

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

9. Remote Sealing System Sensitivity 9. 1 Introduction In the previous sections a description of the overall system has been presented along with detailed descriptions of the equipment and techniques employed with the preliminary probing system, the seal em¬placement system and the seal checking system. In addition, the use of these subsystems in a specific mine application has been described in considerable detail. A broad range of parameters of interest was specified in the contract, as summarized in Section 1. 3. Most of these are a function of the general location; i. e. , the location of the mine, and the specific location; i. e. , the location of the boreholes. These parameters of interest include passage size, shape, depth, slope and water con¬ditions. The length, diameter and location of the boreholes within the mine passage and on the surface are critical parameters as well. A few additional parameters may affect one or more of the remote sealing subsystems. These include temperature, topography, rock and soil conditions, and underground water. While variation in these parameters will not render the system inoperative, consideration of them in the planning stages will simplify and expedite the field operation. In the following sections the effect of the various parameters on the remote sealing operation will be discussed. For clarity, the several tasks, borehole drilling and casing, preliminary probing, fly ash delivery, foam topping and seal checking, will each be considered separately.

Jan 1, 1973

By J. O. Winget

Amino acids were investigated in conjunction with rare-earth separation by ion exchange to determine whether they can be utilized effectively as retaining agents for metals separation using ethylenediaminetetraacetic acid (EDTA) eluant at 85° to 90° C. Hydroxyethylethylenediaminetriacetic acid (REDTA) and diethylenetriamine pentaacetic acid (DTPA) were the most effective amino acids investigated. Elements of atomic numbers 39 and 57 through 68 were effectively retained, whereas elements of atomic numbers 69 through 71 passed through the retaining-agent band. Utilization of REDTA or DTPA retaining agents allows an increase of 75 percent in the EDTA eluant concentration over that possible with hydrogen-or copper-retaining ions without precipitation occurring. Eighty-five percent recovery of the EDTA eluant collected before rare-earth breakthrough and during elution of lutetium, ytterbium, and thulium, and essentially complete recovery of the REDTA or DTPA retaining agents, are possible without extensive processing.

Jan 1, 1968

By R. V. Lundquist

Past reports by the Bureau of Mines have described the extraction of alumina from numerous aluminum silicate materials by the lime-soda sinter process. The results from pilot-plant investigations of six materials, with alumina-to-silica mole ratios from 0.3 to 8.7, indicated a relationship between the alumina-silica ratios and the processing characteristics of the sinter. A series of laboratory tests was conducted to define this relationship. Sinter and leach tests determined that an alumina-to-silica mole ratio of 0.90 or greater resulted in the best alumina and soda recoveries while leaving the leach slurries practically free from any tendency toward gelation. The widely different chemical and mineralogic properties of the various aluminous materials used in compounding the mixes had no perceptible effect on the leaching characteristics of the sinter. The blending of low-cost, high-alumina materials with aluminum silicate materials to give an alumina-to-silica mole ratio of 0.90 or greater would improve alumina and soda extraction and minimize operating problems in the lime-soda sinter process.

Jan 1, 1970

By R. W. Van Dolah

The feasibility of formulating cap-sensitive slurry explosives for use in underground mines with potentially flammable gas atmospheres was examined. Formulations containing aluminum metal as sensitizer and sodium chloride to reduce incendivity were prepared; some were cap-sensitive and had adequate air-gap. Flaked aluminum metal rather than the atomized type proved to be the more effective sensitizing agent of the formulations tested for incendivity in the large gallery of the Bureau of Mines, some were found to be suitably nonincendive.

Jan 1, 1968

Provide minx operators with means for evaluating dust generation and bit wear effects on Production without costly and extensive underground testing. Approach Develop personal-computer-based cutting system models that will simultaneously evaluate machine, Coal seam, and mine-operator-controlled parameters for their interactive effects on dust generation, bit wear, and Production by either a longwall shearer or a continuous miner. How It Works CSM Programs have been developed to analyze relative dust generated by a double-drum, ranging arm, longwall shearer and a continuous miner. These interactive programs Provide relative dust, culling forces, and production values for any given set of mining machine parameters, specific seam conditions, and operator-controllable parameters. Expanded versions of each program provide a dynamic evaluation of the effects of bit wear, over time, on production.

Jan 1, 1989

By John C. LaScola

The Bureau of Mines repeatedly surveyed a grid of monuments over an active longwall mine panel in southwestern Pennsylvania during a 1-year period. Both conventional ground surveying techniques and photogrammetry were used. The objective of this investigation was to compare elevation measurements of subsidence obtained from aerial and ground survey methods under dynamic ground conditions. The results of a statistical analysis of the survey data show that the mean of the differences between 372 matched pairs of elevation measurements was 0.20 ft (61 mm) with a 95-pct-confidence interval of 0.05 ft (15 mm). The mean of the absolute values of the differences was 0.38 ft (116 mm) with a 95-pct-con-fidence interval of 0.04 ft (12 mm). Ninety-five percent of the absolute values of the differences were less than 1.11 ft (338 mm).

Jan 1, 1988

A survey of roof and pillar conditions in underground limestone mines in the United States has revealed that bench mining of the floor between pillars can cause instability in the pillars at the perimeter of the benched area. Increased loading of these pillars was observed at several mines. Large inclined geological structures that are exposed in pillar ribs were observed to contribute to pillar instability. The paper describes a study that was carried out using numerical models to assess the effects of bench mining on pillar load and stability. It was found that the benched pillars shed load onto the surrounding pillars owing to their reduced stiffness. The pillars at the perimeter of the benching area will start shedding load as soon as benching increases the height of one side of the pillar. A case study is described which shows the effects of bench mining on limestone mine pillars.

Jan 1, 2007

By Isaac A. Zlochower, Kenneth L. Cashdollar

The Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) conducted a study of the explosibility of various metals and other elemental dusts, with a focus on the experimental explosion temperatures. The data are useful for understanding the basics of dust cloud combustion, as well as for evaluating explosion hazards in the minerals and metals processing industries. The dusts studied included boron, carbon, magnesium, aluminum, silicon, sulfur, titanium, chromium, iron, nickel, copper, zinc, niobium, molybdenum, tin, hafnium, tantalum, tungsten, and lead. The dusts were chosen to cover a wide range of physical properties-from the more volatile materials such as magnesium, aluminum, sulfur, and zinc to the highly "refractory" elements such as carbon, niobium, molybdenum, tantalum, and tungsten. These flammability studies were conducted in a 20-L chamber, using strong pyrotechnic ignitors. A unique multiwavelength infrared pyrometer was used to measure the temperatures. For the elemental dusts studied, all ignited and burned as air-dispersed dust clouds except for nickel, copper, molybdenum, and lead. The measured maximum explosion temperatures ranged from "-1550K for tin and tungsten powders to "-2800K for aluminum, magnesium, and titanium powders. The measured temperatures are compared to the calculated, adiabatic flame temperatures.

By Robert W. Freedman, Benjamin I. Ferber, Wayne H. Duerr

Vacutainers are employed by the Bureau of Mines and the Mining Enforcement and Safety Administration for sampling mine air and other atmospheres containing fixed gases, low-molecular-weight hydrocarbons, and products of combustion. Tests were conducted to study shelf life of evacuated samplers prior to sampling and also to check the stability of sampled gases prior to analysis. An unexplained phenomenon, slow accumulation of carbon monoxide in evacuated samplers, occurred after a few weeks' storage; levels were low but increased with time and could pose a problem for critical applications. Accordingly, attempts to halt CO release by additional means of treatment were made, and storage at low temperature was found to be effective.

Jan 1, 1978

By Harold F. Unger

The Bureau of Mines conducted drilling experiments in the laboratory with a commercially available percussive drill that has an independent rotational system. Eight rock types with a wide range of physical properties were drilled under several combinations of rotational speed, drilling thrust, and operating pressure. Penetration rates and energy per unit volume correlated well with the coefficient of rock strength as shown graphically. Size-distribution analyses of some of the drill cuttings show how particle size varies with rotation speed and rock hardness. In general, changing the rotational speed has a greater influence on the penetration rate in softer rocks, with penetration rate increasing with increasing rotational speed.

Jan 1, 1972

Reduce respirable dust in coal preparation plants. Approach Survey a representative sample of coal preparation plants to (1) determine the dust problem extent, and (2) evaluate practical dust control techniques. Coal Preparation Plant Survey Results Of the approximately 500 coal preparation plants in the United States, 18 plants in six States were randomly selected for survey. The raw hourly capacities ranged from 250 to 1,250 tons, plant construction dates ranged from 1037 to 1982, and usually 3 to 10 workers were required per shift. Respirable dust concentrations within the plants surveyed ranged from very good (less than 1 mg/m') to very poor (14 mg/m3). No relationship was found between dust concentration and age or capacity of the plant. Six of the plants had long-term respirable dust concentrations between 7 and 14 mg/m' in specific areas; six had concentrations between 2.2 and 6.2 mg/m'. Except fur ventilation, only 4 of the 18 plants used operating dust control devices with mixed effectiveness.

Jan 1, 1989