Search Documents

Between 1993 and 2003, a series of AG and SAG mill pilot plant trials were conducted using Hardinge Ical pilot plant scale SAG mills on numerous ore samples and ranging across a wide variety of operating conditions. The data from these tests were used to evaluate the design of SAG and AG mill circuits for over a dozen projects, of which about half were eventually constructed and commissioned. The data were also used in the development of SAG mill modelling, scale-up and simulation procedures by several consultants who had access to part of the data set. Recently, we have had the opportunity to bring this data together and further analyse the consolidated dataset. This paper reports on the outcomes of this analysis that has identified the impacts of different AG/SAG circuit flowsheets and operating conditions on energy efficiency and operating cost.

Jan 1, 2012

By T. Schepp, T. Friedrich

"The natural stage of deep mines operation is a closure of unnecessary shafts. It is extremely important to ensure a proper shaft closure to avoid stability loss and the associated damage to surface facilities in the future. For the still active shafts, it can be done by a dedicated shaft closure design, but even then, depending on the shaft closure method, it may be necessary to perform regular shaft inspections. The paper presents a short overview of shaft closure methods and available tools and devices developed in the last time for such shaft inspections. INTRODUCTION The natural stage of deep mines operation, commonly occurring after depletion of the reserves of mined materials, is a closure of unnecessary shafts. All over the world, the number of liquidated shafts grows continuously and the problem of shafts disposal is especially critical for deep shafts. The typical depth of 600 m of currently liquidated shafts in Poland may already be seen as a challenging task. The greater is the challenge of shaft closure in Germany where the last active coal mines for shafts with a depth of up to 1,300 m have been recently closed. It is therefore extremely important to ensure a proper shaft closure to avoid stability loss and the associated damage to surface facilities in the future. For the still active shafts, it can be done by a dedicated shaft closure design, but even then, depending on the shaft closure method, it may be necessary to perform regular shaft inspections. In many cases, it is more important to inspect old, abandoned shafts, where the wall stability or even liner type are not fully known. SHAFT CLOSURE METHODS Abandoning a shaft is a complicated task, as shafts, being the link between the surface and an underground network of workings, disturb hydrogeological and gaseous conditions in the rock mass (Sztelak, 1991). Closure procedures at older mine sites have been carried out in accordance with earlier legislative requirements. For very old shafts (+100 years), it means in many cases only a sealing of the shaft entrances by means of timber or concrete slabs. In the 20th century, the shafts were also closed by means of filling with grainy materials, but even then the retrospective activities at abandoned mine sites were extremely limited and in most cases no further monitoring measures were performed. The possible consequence of an improper shaft closure and lack of monitoring is presented in Figure 1."

Jan 1, 2019

By V. ?. Chanturiya, I. Zh. Bunin, M. V. Ryazantseva

"Surface changes in naturally occurring metal sulfides (pyrite, arsenopyrite, sphalerite, chalcopyrite, galena, and molybdenite) due to treatments from high-power electromagnetic pulses (HPEMP) at varying times were studied using X-ray photoelectron spectroscopy. Analysis of the obtained results revealed common patterns and differences in surface transformations. The transformations were found to include two main stages. The first stage was observed at low treatment intensities (up to n ~103 pulses). At this stage, formation and accumulation in the surface layer of the nonstoichiometric sulfide phase, oxides and hydroxides, as well as elemental (polysulfide) sulfur and/or metastable sulfur species (thiosulfate, sulfite) was observed. The second stage (N = 3·103 pulses) is characterized by thermal removal of sulfur species and renewal of the mineral surface (sulfidization).It was found that the chemical changes of the sulfur on the surface layer of pyrite, arsenopyrite, chalcopyrite included accumulation/formation of S0 (Sn 2-) at the first stage of the transformation, followed by its removal. An increase in the surface concentration of elemental sulfur for pyrite and chalcopyrite was 10–12% while arsenopyrite was approximately 5%. A more complicated chemical change was observed for sphalerite and galena, that included formation/accumulation of metastable sulfur species (thiosulfate, sulfate) at the initial stage (up to 103 pulses) and during longer treatment times, the sulphur is reduced back to its initial state (sulfide or disulfide). The increased concentration of S0 sulfur, compared to the original sample, was only 3% in galena and sphalerite.The application of HPEMP treatment to improve flotation selectivity is supported by singlemineral flotation tests. Changes in flotability as a result of HPEMP treatment are principally explained by surface phase changes that resulted in higher adsorption activity."

Jan 1, 2016

By T. T. Wang, T. H. Huang, S. S. Zhan

"Fractures with diverse features dominate the hydraulic behavior of fractured rocks and are one of the major subjects for hydrogeological characterization of a site. This study investigates curve patterns obtained by packed tests, and as well the influence of fracture features based on 59 sets of in situ packer tests with different fracture combinations and fracture features. The result shows that, in the example of Heshe site, neat and tidy fractures usually provide stable channel for water flow during testing, and the hydraulic properties of fractures infilled with breccia and mud may change during testing because of leaching and/or washed out of infilling breccia and mud. Different combinations of fractures with diverse features in packed test sections lead to different curve patterns for in situ hydrogeological tests. For groundwater flowing predominately through neat and tidy fractures, the pressure-discharge curve of modified Lugeon tests are usually linear curve pattern, and the pressure decrease while the discharge increase in pressure-discharge-time curves of single-hole double packer tests, which benefit statistically determining the transmissivity of dominant fracture sets. INTRODUCTIONFractures interlaced in rock masses are major channels for groundwater flow and generally account for the anisotropic and heterogeneous characteristics of permeability for fracture rocks. To describe reasonably the permeability of a fracture rock, the Discrete Fracture Network (DFN) approach and others with similar ideals have been developed. Many methodologies and associate equipment, for instance, the televiewer and the in situ hydrogeological test, have been proposed to investigate the spatial distribution and the transmissivity for different fracture sets, which are two main parameters necessary for the DFN or similar model simulation (Pearson & Money, 1977; Barker & Black, 1983; Hsieh et al., 1985; Bernard et al., 2006; Quinn et al., 2012). However, diverse outlooks for the pressure-discharge curves and the temporal pressure and associate temporal discharge curves often confuse the investigation results by significant deviations on derived permeability (Houlsby, 1976; Zlotnik, 1994; Royle, 2009; Camilo, 2010).Aiming on technical development for in situ hydrogeological tests and fracture investigation, an experimental well site with 10 wells has been established in Heshe in central Taiwan since 2011 (Wang et al., 2011; Song, 2012; Zhan et al., 2013). Extensive geological survey and well-hole scanning by a televiewer provide spatial distributions and outlooks of fractures in detail. Additionally, a series of Lugeon tests, double packer injection tests and pumping tests have been performed to investigate the permeability of fracture rocks, and dominate fracture sets as well. Based on the results obtained from the Heshe site, this study classifies the curve patterns of hydraulic packer tests. The features of fractures involved in packed sections for packer tests are then inspected in detail. Relationship between the curve patterns of hydraulic packer tests and associated features of corresponding fractures in rock are discussed and addressed accordingly."

Jan 1, 2015

By K. M. Mayhew, G. D. Barr, T. M. McCoy, C. T. Knilans

"Teck Resources Limited (“Teck”) has developed and extensively tested on a continuous basis the CESL Technology hydrometallurgical process for treating copper and nickel sulphide concentrates, including bulk copper-nickel concentrates. Copper, nickel and cobalt are leached efficiently into solution, utilizing CESL process conditions. Total precious metals including gold, silver, platinum and palladium are recovered from the residue stream via sulphur flotation. This paper describes the CESL Technology testwork on a bulk copper-nickel concentrate derived from Twin Metals Minnesota?s (TMM) deposits within the Duluth complex and evaluates the economic benefits (increased cash flow, increased revenue certainty) and investment criteria (capital cost, payback and cash flow) of incorporating CESL Technology into the staged development of TMM?s deposits.INTRODUCTION Mineral Processing and the Role of Hydromet in the Duluth Complex The Duluth Complex in northern Minnesota, United States (US), represents one of the largest undeveloped accumulations of copper, nickel, gold, and platinum group metals (PGMs) in the world, ranking second in copper and PMs and third in accumulation of nickel. The figure below identifies some of the larger known deposits within the Complex (see Figure 1). Copper, nickel, PM and PGM mineralization within the Duluth Complex is hosted by mafic to ultramafic intrusive rocks that are part of the overall intrusive complex.One of the mineral processing challenges of Cu-Ni-PM-PGM deposits in this Complex is the complicated, polymetallic nature of the mineralization1: copper occurs primarily as chalcopyrite and cubanite with minor occurrence of talnakhite; nickel occurs as pentlandite and refractory nickel oxide/silicates; iron sulphides are present as both pyrrhotite and troilite; and PMs/PGMs occur in both the sulphide matrix as well as discrete minerals. An additional challenge for the Duluth Complex is the ratio between copper and nickel; in most of the identified deposits, copper grade is three to four times greater than the nickel grade, which precludes the production of a simple bulk concentrate due to the lack of a traditional smelting market for a bulk concentrate of this character."

Jan 1, 2017

By Ralph J. Holmes, David McCallum, Alan Roberts, Rolando Orense, University of Auckland, Tobias Krull, Tom Honeyands, Kenneth Williams

"The safe ocean transport of bulk commodities like iron ore, coal, nickel ore, manganese ore and bauxite by large bulk ships is vitally dependent on the stability of the cargo under the influence of wave induced ship motion. Safety standards are set by such bodies as the International Maritime Organisation (IMO) with recommended tests for the assessment of bulk commodities. Since the 1960s, the bulk cargo code (BC Code) commenced defining methods to determine the Transportable Moisture Limit (TML) for transportation of bulk commodities. By the latter part of the 1960s, three TML test methods were defined, namely the Flow Table, Proctor-Fagerberg and Penetration tests. All three tests were predominantly aimed at determining TML values for mineral concentrates.More recently, bulk commodity producers, Maritime Organisations and Port Authorities worldwide have been investigating whether commodity based TML methods better reflect realistic safe ship transportation than the current concentrate based TML test methods. In these investigations, the relationship between the mineralogical and particulate parameters of specific commodities with respect to cargo stability and moisture retention has provided insights into the development of tailored TML test methods. To this end, an AMIRA International project (P1097) undertaken by CSIRO, TUNRA Bulk Solids, the University of Newcastle and the University of Auckland assisted the IMO Technical Working group to investigate the relationship between iron ore fines characteristics and a new TML test specific for iron ore fines bulk cargoes.A review of the three standard concentrate based TML methods and characterisation studies of iron ore fines, as well as cyclic triaxial testing to determine liquefaction resistance, resulted in the development of a modified Proctor-Fagerberg method for determining the TML of iron ore fines. Of particular importance in determining TML is mineral composition, porosity, particle density and allowing time for moisture equilibration."

Jan 1, 2016

By S. K. Sharma, Sanket Bacchuwar, Prabal Kumar Agrwal, G. V. Rao

"Iron ore processing industries play a vital role in the Indian economy. At present Iron ore of around +64% Fe is used for production of Iron through blast furnace. To produce +64% Fe from low/medium grade ores, crushing & beneficiation is compulsory. But during these processes, large amount of slime is generated. It is estimated that 18% -25% of tailing is generated during the processing of iron ore. The iron ore slime is discarded because of its particle size and chemical composition not being suitable as feed to the blast furnace. Although the fines/slimes can be agglomerated to larger particle, the alumina to silica ratio which is normally more than one pose serious problem during sintering process and subsequent smelting in blast furnace. The alumina content in the slime needs to be reduced for it to be used as the feed for blast furnace. The sample assayed 61.40% Fe, 7.68% SiO2, and 1.52% Al2O3, LOI 2.63% and all other elements were found in critical limit. A series of 27 tests were conducted by using a spiral for optimisation of process parameters to produce a pellet grade concentrate from the stacked slimes obtained from Kirandul. This paper deals with the optimisation studies of various parameters of a spiral concentrator and helps to utilize the fines from tailing ponds.INTRODUCTIONReserves of high-grade iron ores are diminishing all over the world at an alarming rate. As a result, alternative ways of augmenting and conserving precious and non - renewable natural resources are being seriously considered. One such attractive option is the recovery of metal values from slimes / tailings. Iron ore tailings containing around 48 - 60% Fe are generated from the iron ore washing plants and are disposed into tailing ponds without any further utility. These tailings in the form of slimes are not suitable in iron and steel making due to the presence of higher amount of gangue constituents. Several beneficiation techniques have been tried from time to time to reduce the gangue so that the beneficiated products could be effectively used."

Jan 1, 2016

By K. Spence

"The notion of “value” has always been a subjective and contentious issue. Indeed, value is in the eye of the beholder. There are as varied methods and practices for valuing property, as there are industries in which they are applied. For example, there is replacement value, insurance value, salvage value, appraised value, book value, and fair market value, to name a few, although in the mining industry, valuations usually refer to fair market value.In the Canadian mining industry, at present, there are no comprehensive regulations or guidelines that specify which approaches or methods are appropriate for use in the valuation of mineral projects. In January 1999, The Mining Standards Task Force of the Toronto Stock Exchange and the Ontario Securities Commission recommended that the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) establish a committee to review and advise on approaches and methodologies for the valuation of mineral properties. Among the approaches to be considered are included the following: the discounted cash flow approach, the cost approach, the option pricing approach and the market comparables approach. In addition, methodologies differ depending on whether the project is at the exploration stage or the producing stage.The CIM Special Committee on the Valuation of Mineral Properties (CIMVal) expects that its final report will form the basis for a Canadian code or standard for the valuation of mineral properties."

Jan 1, 2002

By F. Chiesa

Experimental results on thin and thick castings poured in aluminum A356 and magnesium AZ91E by the low pressure permanent mold process have been compared to the result of filling simulations for thin and thick castings. If the results of modeling is reliable when the liquid remains above the liquidus temperature, this is no longer the case when partial solidification occurs. The visco-elastic behavior of a partially solidified liquid is difficult to put into equation as it depends on the amount of shear it has been been subjected to. Attempts to predict misruns with a commercial software has been proven to be very difficult if not impossible; divergence of the numerical solution has been observed unless prohibitively long computing times are used. In order to overcome these difficulties from a practical standpoint, a simple method is proposed which consists in tracking the temperature of the advancing liquid metal front so as to make sure it will always be above so-called `Misrun Critical Temperature' (MCT) determined experimentally for thin and thick aluminum A356 and magnesium AZ91E castings. If the liquid metal front falls below this temperature, a cold-shut or misrun is likely to happen at this location. The values of MCT for thin and thick in aluminum A356 and magnesium AZ91E were determined experimentally on misrun castings of extreme geometries (a thin 2.5 mm wall cover and a 6mm to 25 mm thick bell housing). MCT was found to be lower for magnesium AZ91E and for the thicker castings.

Jan 1, 2011

By Peter Rubie

For many years, optimising the relining of hard rock grinding mills has been complicated by: ?? the large number of variables; ?? the low frequency of relines (slow feedback loop); ?? the potential economic risk associated with some changes. A technology that has its roots in the automotive manufacturing industry is being utilised to construct a statistically accurate, configurable, and dynamic simulation of the mill relining process. The effects of various mechanisation and process changes can be rapidly modelled and compared. This technology will provide mill maintenance managers and contract relining companies with the opportunity to benchmark current performance against world?s best practice. It will also provide an opportunity for concentrator plant designers and mill manufacturers to plan for maximum plant efficiency, by designing an infrastructure and equipment combination that maximises annual plant availability. This simulation tool and its associated data set, has been developed using recent grinding mill performance data from mills of varying dimensions, liner configurations, mill relining equipment, operator and tool variables. The simulation will provide an output that the various stakeholders can utilise to make optimal decisions within the given financial, physical and technological constraints of the individual concentrator plant.

Jan 1, 2012

By H. C. M. Gordon

MR. A. D. BADOUX: I have listened to Mr. Gordon's excellent paper with great interest, as I personally have gone through some of the experi­ences he has so clearly depicted. In particular, there were a good many times when we were greatly exercised in our minds as to whether we were justified or not in closing-off certain sections in the Allan mine. The difficulty in these cases arose from the fact that a peculiar smell could be detected in these sections but at the same ti me there was no positive evidence of spontaneous combustion either from heat being apparent or from the possible indications of fire getting any worse. It was suspected that the small percentage of -carbon monoxide that could be obtained by analysis in the air in these sections, and also the peculiar odour, were emanating from the coal itself, and, in order to verify this, bore-holes were drilled in the coal and the gases released from these bore-holes were analyzed. They were found to contain carbon monoxide. After quite a considerable length of time this contained carbon monoxide gradually diminished and finally could not be detected when analyzing such samples of gas. It was our intention to follow this matter up further, as such an occurrence of carbon monoxide is practically unknown, but the sections in which these occurrences were found had to be abandoned. Mr. Gordon referred t0 a case of spontaneous combustion in the Allan . mine, and I may say that, although the section in which that occurrence took place was travelled and carefully examined every day by the colliery officials, yet nothing unusual was noticed until the fire actually took place. This tire was the cause of a slight explosion.

Jan 1, 1938

By E. V. Konopleva, H. J. McQueen

"The isothermal bainite transformation kinetics of low- and medium-carbon alloy steels after hot deformation and the rmocycling treatment (TC) has been studied by the magneto - metric method. Deformation was produced by rolling at 800°C-1000°C. TC included three cycles of rapid (30°C/s) electro-heating up to 900°C-1000°C followed by quenching.Hot deformation retards bainite transformation in the lower part of bainite range (<400°C) and accelerates it in the upper part (>400°C). The effect is greater for higher strain and lower deformation temperature. Deformation also diminishes the overall bainite fraction below 400°C and increases the completeness of reaction above 400°C.Thermocycling provides more uniform ultrafine austenite grains with average size of 3 µm -4 µm compared to 12 µm -14 µm after conventional heating. The transformation rate after TC was almost the same as after conventional heating in low-carbon steel but was faster in medium-carbon with no change in the completeness of reaction. The degree of acceleration increased with rise of transformation temperature.There are a number of factors which are responsible for a change in bainite transformation kinetics in austenite deformed at high temperatures or subjected to TC. One of the most important factors is the refinement of structure, another one is structural and chemical inhomogenity of austenite due to deformation or to rapid heating. To estimate the contribution of these factors, ?-transformation was studied after different austenitizing conditions (low-temperature heating at 850°C- 950°C; high-temperature heating at 1100°C; step treatment – austenitizing at 1100°C, then cooling to 950°C-850°C). The results obtained make it possible to conclude that the structural and chemical inhomogeneity of austenite activate the bainite reaction while the grain refinement retards it. Intensity of the effect produced by each factor depends strongly on the steel composition."

Jan 1, 1997

By Jean-Louis Robert

Field work inaugurated in 1962 in the townships of Lemieux and Lesseps, in the Gaspe Peninsula of Quebec, has permitted the author to delineate the lithologic units of the area, to elucidate a few stratigraphic problems and to outline several zones of alteration. Certain features of these zones and the numerous mineralized showings in the area merit the attention of prospectors and exploration companies.

Jan 1, 1966

By D. Maddocks

"IntroductionThe greater part of the iron ore industry in Canada is located along the Labrador-Quebec border on a geological formation known as the Labrador trough. The Labrador trough is a 700 · mile long geosynclinal segment composed of folded and faulted Proterozoic sediments, volcanics and intrusives, extending from Gagnon, Quebec, to the north west tip of Ungava Bay. This geosyncline can be divided into three parts (Fig. 1).The northern unmined part, extending from southern to northern Ungava Bay, is a low grade metamorphosed iron formation.The iron deposits of the central region, represented by Schefferville, are hematite-limonite ores formed by oxidation and leaching of an unmetamorphosed taconite formation. Average iron content of the ore is greater than 540Jo for direct shipping and 50% for plant feed.The deposits of the southern section (Carol Lake, Wabush, Mt. Wright, Gagnon) extend from just north of Carol Lake to Gagnon and is a metamorphosed silica-iron oxide (specular hematite and magnetite) formation averaging plus 30% iron.The mineral wealth of this area was first observed by Father Louis Babel about 1870 and again by Dr. A.P. Low of the Geological Survey of Canada in 1894. However, the remote location hindered development until after 1945. First production of direct shipping ore from Schefferville was in 1954. Production at Carol Lake commenced in 1962.This area now accounts for sixty million long tons (61 Mt) per year of processed iron ore products as follows:This chapter will concentrate on pelletizing and agglomeration as experienced at the Iron Ore Company's Carol Lake operation. However, whenever possible, reference will be made to alternate methods, procedures, equipment, etc."

Jan 1, 1989

By A. Blackmore, A. Lamoureux, J. Woloshyn

This paper provides an overview of recent applications of Computational Fluid Dynamics (CFD) to combustion related fugitive emissions problems. The aim is to illustrate the capabilities and discuss the present limitations in this field. Examples include design of retrofitted NOx reduction technology in a kiln and in a boiler, and the prediction of pollutants such as SO2 and metallurgical dust emanating from a copper flash smelting furnace. It is demonstrated that CFD is an effective tool for reducing technical risk in design, for identifying the root-cause problems and testing solutions, and for concurrently assessing emissions reduction and process impact. In addition, the value of CFD for demonstrating due diligence for regulatory compliance is discussed.

Jan 1, 2015

By A. Pranowo, G. R. F. Alvear F., N. Aslin, M. S. Moats

"The toxicity of arsenic is well known and documented; however, the presence of arsenic in copper electrorefining anodes and electrolytes is critically necessary to produce high-quality cathode. Arsenic as well as antimony and bismuth concentrations vary relative to their concentration in the anode copper received from the smelter. The behaviour and benefits of arsenic in copper electrorefining and the detrimental effects of antimony and bismuth on cathode quality and tankhouse performance are discussed. This will include the minimization and mitigation of problems associated with arsenic, antimony, and bismuth—including cathode contamination, floating slimes, scaling, and anode passivation.RÉSUMÉ La toxicité de l’arsenic est bien connue et documentée; toutefois, la présence d’arsenic dans les anodes de l’électroaffinage du cuivre et dans les électrolytes est d’une nécessité critique pour produire une cathode de grande qualité. Les concentrations en arsenic, ainsi qu’en antimoine et en bismuth varient selon leur concentration dans l’anode de cuivre reçue de la fonderie. Le comportement et les avantages de l’arsenic dans l’électroaffinage du cuivre et les effets indésirables de l’antimoine et du bismuth sur la qualité de la cathode et le rendement des cuves d’électrolyse sont discutés. On traite aussi de la minimisation et de l’atténuation des problèmes associés à l’arsenic, l’antimoine et le bismuth – incluant la contamination de la cathode, les schlamms flottants, l’entartage et la passivation de l’anode."

Jan 1, 2016

By Walter Greaves

THIS paper describes a series of tests performed at the Hollinger mill during the past four years, in which both metal and rubber-lined pumps were used for pumping sand and slime. While conditions will not be the same at other mills, it is felt that the information gained from the tests should be of value to other operators and of assistance to them in selecting the most efficient size of pump and kind of lining for economical operation. For the successful operation of pumps with rubber linings there are certain conditions, which, if recognized at the outset, will save the operator a good deal of work and trouble. First is the necessity of keeping sharp pieces of steel, or anything that might cut the lining, out of the pumps. This can be effected by placing screens in the proper locations. Second is to recognize the fact that the rubber lining of the shell, and the rubber cover of the impeller, are subjected to very different conditions. The shell lining, :being at rest and well supported by the metal case, has a relatively easy job compared ? with the impeller covering, which is subjected to centrifugal force and has a tendency to tear itself away from the metal core. Also, the pulp travels through and past the impeller at a high velocity. These two factors, centrifugal force and velocity of the pulp, would appear to set a limit to the speed at which, for a given set of conditions, it is economical to run a rubber-covered impeller. Therefore, a pump should be large enough for the work to be done. To get the best mechanical efficiency, it must be operated somewhere near the limit of its capacity, but this may not give the best overall cost, because the saving in power, due to the high efficiency, may easily be lost through excessive wear on the lining. It would appear that this condition is more critical in a rubber-lined pump than in one lined with metal.

Jan 1, 1939

By D. J. MacKinnon

"The Canadian Copper Company, formed in 1885, began mining the nickel-copper ores of Sudbury in 1887 and producing nickel-copper matte from its smelter in 1888(1). Although it was quickly appreciated that the separation of nickel and copper (i.e. refining) was critical to the production of a marketable nickel product, refined nickel was not produced in Canada until about 1918. From the beginning of the industry, there was considerable political agitation to refine nickel in the Province of Ontario(2). The companies, however, claimed that the existing processes, viz. the sodium sulphide ""tops and bottoms"" process operated by the Orford Copper Company of New Jersey, U.S.A.(1,3,4) and the carbonyl process(5,6) developed by the Mond Company at Clydach, Wales, were too costly to operate in Canada. Nickel was first refined in Ontario about 1918 when the International Nickel Company opened a nickel refinery at Port Colborne, Ontario(6). Initially, however, the refinery at Port Colborne employed the Orford sodium sulphide process, and the first electrorefined nickel in Canada was produced in 1920 by the British America Nickel Corporation whose mine and smelter were located in Sudbury, Ontario, but whose electrorefinery was located at Deschenes, Quebec, near Ottawa, Ontario. The purpose of this article is to outline the early history of nickel electrorefining and to trace the significant developments which led to the first successful commercial electrolytic nickel refinery in Canada. The development of an electrolytic process for refining nickel is due largely to the efforts of four individuals, viz. Carl Hoepfner, Hans A. Frasch, D.H. Browne and ultimately N.V. Hybinette, and the contribution of each is discussed separately below."

Jan 1, 1999

By Chuanhui Cao, Shimei Liu, Xiaojing Li, Yueyuan Zhou

"Force analysis on weakly-magnetic particles and non-magnetic particles in magnetic field are presented, using a kind of permanent magnetic drum magnetic separator, which is designed with strong specific magnetic force and open magnetic system. Its surface peak intensity reaches to 1.0T, and the distribution density of capture line is 1.25×103/dm2. Qualitative analysis on the particles including its magnetic property, particle size, motion speed, magnetic field intensity, etc. is also presented to calculate the separating parameters for the drum separator. Experiment was conducted for the separation of fine weakly magnetic minerals for example ilmenite. The practicability to separate the minerals using separator designed with open magnetic system has been proved, providing an economic way for efficient separation of micro-fine weakly magnetic minerals and upgrading of non-metallic minerals. INTRODUCTIONMagnetic separation is a mineral processing method based on the differences of magnetic properties between minerals in inhomogeneous magnetic field (Sun, 2007). Currently for separation of micro-disseminated weakly magnetic iron ore, electromagnetic high intensity magnetic separators with closed structure of magnet system are often used. And for the separation of strongly magnetic minerals such as magnetite, low intensity drum magnetic separators with open magnet system are often used. In order to lower the operation costs and improve energy efficiency, it is important to develop efficient high intensity permanent magnetic separator with open magnet system, to some extent replacing high intensity electromagnetic separator.Oberteuffer (1974) discussed the magnetic force and competing forces in magnetic separators which compete with the magnetic forces and act on all of the particles which travel through the separator are those of gravity, hydrodynamic drag, fraction, and inertia in magnetic separation."

Jan 1, 2016

By Jeffrey S. Loen

"Abstract - The size, morphology, surface texture, per cent mineral inclusions, and bulk chemistry (Ag and trace elements) of placer gold particles vary systematically according to transport distance from source rocks, as indicated by a case study from the Pioneer district in Montana, and data from the literature.Placer gold samples show a rapid decrease in mean and maximum particle length, and a gradual increase in flatness index (F.I. = length + breadth/2 X thickness) from about F.I. = 2 in bedrock deposits, to as much as F.I. = 45 over transport distances of several tens of kilometers. Primary mineral inclusions (mainly quartz, sulfide minerals, and iron oxides) are mostly lost within 10 km to 20 km of fluvial transport; this loss of quartz and trace metals causes a major change in bulk chemistry of placer gold samples. Following the loss of inclusions and the development of flakes, edges of flakes are folded and the mean number of folded edges in a sample increases with distance. When viewed under the electron microscope, surface textures of placer gold particles also become progressively more pitted with distance.Analysis of placer gold particles can be used to help evaluate placer source-area problems (placers with no known hard-rock gold deposits). For example, coarse placer gold containing abundant inclusions indicates a proximal source. On the other hand, an abundance of thin flakes is evidence of a long transport distance and possible reworking from older gravels. Placer gold characteristics can therefore provide information on distance to mineralized source rocks."

Jan 1, 1995