Search Documents

By A. Paulin, J. Roth, S. Spaic

This experiment was carried out to see whether copper-iron ingots from Late Bronze Age hoards could have been produced by smelting ferruginous copper ores. Since ferruginous copper-ores are chalcopyritic, chalcopyritic concentrate from a present day copper mine was dead roasted in our experiment in lieu of a rich chalcopyritic ore. Charcoal was used as a reducing agent in the reduction of calcine (i.e., a product of dead-roasting), and quartz sand was used as a flux. Two separate metallic solutions, a copper-base and an iron-base alloy, were obtained as a result of two factors: the presence of carbon and the miscibility gap in the Cu-Fe-C system. The metallic melts appeared in a form of bigger or smaller droplets, enclosed by a molten slag which, during the cooling, solidified into metallic beads. The presence of both metals was noticed in the majority of the examined beads. It was therefore concluded that calcine consisted of an intimate mixture of oxides of both metals which were simultaneously reduced during the reduction process. Due to the miscibility gap in the Cu-Fe-C system, separate iron and copper regions were formed in the beads. In both regions, sulphide inclusions were found. The formed molten copper and molten iron solution were found to be saturated solutions. The metallographic analysis revealed the precipitation of iron out of copper and that of copper out of iron during the cooling and solidification of melts. The formed slag contained little iron and no copper oxide.

Jan 1, 2001

By G. Kolosay, J. Rajala, G. Deschênes, A. Romanov

ABSTRACT: The Kupol project, located in Far East Russia, treats a high-grade, free-milling ore containing 25.5 g/t Au, 298.3 g/t Ag, and 0.5% pyrite,with a P70of 53 microns. Most of the gold occurs as elec-trum and the silver is predominantly present in the forms of acanthite, stephanite, pyrargyrite, andproustite. The mill reached the design throughput of 3,000 tpd six months after start-up. AKnelson con-centratorrecovers10.4% gold and 0.5% silver. Leaching (14.5 hours pre-treatment and 116 hours cyanidation)of gravity tailings is performed with the CANMET Enhanced Leach Process (CELP),using only 490 ppm NaCN (cyanide consumption of 1.1 kg/t). The precious metals are recovered by counter-current decantation and the Merrill-Crowe process. Calcium hypochlorite destroyscyanide and thiocyanate. Overall, gold and silver recoveries for 2008 were 95.4% and 85.6%,respectively (2.8% and7.5% higher than targets). In the first eight months of 2009, gold and silver recoveries were 95.0% and82.6%, respectively. By August 2009, the mill processed 1.42 million tons of ore with production of 1.1 million ounces of gold and 11.3 million ounces of silver. CELP performance was not affected by changes in feed grade and ore mineralogy. Additional modifications to the leaching strategy allowed further reduction in cyanide consumption and effluent treatment costs.

Jan 1, 2011

By K. A. Clark

A meeting between representatives of the Scientific and Industrial Research Council of Alberta and the Deputy Minister of Mines for Canada was held at Edmonton in May, 1929, for the purpose of formulating a co-operative plan for carrying forward studies in aid of the development of commercial methods for utilizing the bituminous sands of Alberta. It was agreed that to the Alberta Research Council should be allocated the general problem of investigation of the processes for the separating of bitumen from the sands, including studies of methods of emulsifying, dehydrating and otherwise preparing separated bitumen for industrial applications. It was further agreed that during the present year the work of the Alberta Research Council should be to continue its laboratory investigations of points of design of its separation plant; to further perfect its separation procedure; to recondition its existing separation plant at Dunvegan Yards, Edmonton, in the light of laboratory studies and to operate it for the purpose of demonstrating its efficiency; to carry on tests in emulsifying and dehydrating or otherwise preparing separated bitumen for industrial application; and on the basis of the experience gained in the operation of the preliminary plant at Dunvegan Yards to prepare and design and, as far as possible, to proceed with the erection of, a semi-commercial separation plant at a site to be chosen, probably at the bituminous sand deposits near McMurray, Alberta. This paper presents, in the main, a progress report of the carrying out of this programme.

Jan 1, 1929

By Hulbert A. Lee

"A REVIEW OF MINERAL DISCOVERIES IN CANADA, and in particular the Canadian Shield, using the physical aspects of overburden reveals a trend in the art of exploration. At an early time of exploration (1847-1954), float and heavy clasts were used successfully to find ore deposits with little knowledge of Quaternary environments. At a later time (1955 to present) , use of Quaternary rock-units for sampling have made possible tracing indicator trains of float, heavy clasts and other ore-type clasts to the source bedrock. The basal till of retreat ice is now recognized as a1l favourable sampling environment and as such has been used to successfully discover hidden orebodies. The esker massive gravel is beginning to be recognized as a favourable environment and use of it has met with technical success. An understanding of those changes that have taken place during the transportation of the material and after its deposition is essential to proper sampling and treatment of the samples from the basal till and the esker massive gravel. Use of float and heavy clasts in search of orebodies is continuing in present-day exploration on the Shield. Lessons learned from it are being incorporated into exploration using favourable Quaternary rock-units for sampling. Hence, both subjects have a need for review and are discussed in this paper."

Jan 1, 1971

By T. A. Rickard

FROM AN OLD MANUSCRIPT THE text for this contribution to the history of the Patio process is a page taken from a Spanish manuscript of Bartholomé Arzaj Sanches y Uela, now in the possession of the library of Brown University (see Figure 1). I owe the photographic print to the courtesy of the librarian. The date, as will be seen, is 1577. The subject is the treatment of silver ores at Potosi, in old Peru, but in modern Bolivia. The group of drawings (see Figure 1) is entitled "Arrangement of the machines in which the ores of silver are ground on the bank of Potosi, the one of two batteries and the other of one". First, top-left, we have the sketch of a "machine of one battery" operated by a water-wheel. From this mill the water runs in part along an aqueduct supported by pillars to the two-battery mill and in part down the hillside, where men are at work with "tubs, which are called cochas, in which are washed the charges of ore and amalgam". Along the top of the page are shown the "various offices in which are stored the copper, the salt, the ucha [llama dung, used for fuel], the lime, and other materials for the re-duction of the ores". To the right of these are "apartments and warehouses in which is stored the ore brought down from the mountain"?the cerro de Potosi. Through the arched portal come the "sheep [llamas] on which is brought down the ore". To this is added a reference to "the second gate, which closes the whole works". On the level above the aqueduct are seen six men carrying skin-bags that contain water. This is being sprinkled on the ore. On the extreme right are six more of these water-carriers. Next comes the two-battery mill. The mortero, or mortar, is marked on the right. Another description says, "Stone, on which the stamps crush the ore, which is called a mortar". To the left of these are indicated "screens of wire in which the ore is sifted after it has been crushed". Farther to the left, near the ore-washers, is a "shed, in which is placed the metallurgist to test the ore of the boxes". Along the left side of the page are sundry buildings, one of which is labelled a "shed in which are placed the cones of silver". Near it, lower, to the right, is the "furnace, in which are roasted the sulphides to facilitate treatment". Farther to the right is the "place where the Indians mix the charges of sulphide ore, which is called a buitron". Alongside is a "buitron in which the charges are prepared for reduction". Inside is a container, to which are attached the words "measure, called topo" On the extreme right is "another buitron in which the Indians mix the ores with their feet, as well as the heaps for the preparation of the reduction". Near the bottom, on the extreme left, is the "chapel where the holy sacri¬fice of the mass is celebrated". Under the first buitron is the "place where they dry the moist ores, called pãpear".

Jan 1, 1935

By Eurípides do Amaral Vargas Jr., J. A. de Mello Franco

"It is frequently necessary to excavate a tunnel for Civil Engineering purposes, or wells for petroleum exploitation, in laminated rock mass like schists or phyllites or in highly foliated gneisses. The determination of the pre-existing in situ stresses is essential, in order to assure the stability of these excavations. In most cases, the pre-existing triaxial stress field is arbitrary in relation to the tunnel or well axis. For these rock masses the concept of Generalised Plane Strain can be correctly utilized.There are closed form solutions for the calculation of stresses in anisotropic rock masses under Generalised Plane Strain conditions (Lehknitskii, 1981 and Hong , 1994). Based on these analytical solutions, established for the cases of Generalised Plane Strain, a synthetic problem will be formulated: the theoretical in situ stress tensor acting on this rock mass will be determined, with the aid of Bayesian Inverse Problem Techniques, as developed by de Mello Franco (2009). Additionally, the reliability of results obtained will be evaluated, in accordance with the research performed by this author. INTRODUCTIONThe Inverse Problem Technique, as developed in the paper, is based on the definitions and concepts obtained from the current literature and used for the solution of Inverse Problems, but the innovation to be presented is the utilisation of Bayesian Techniques and the determination of the reliability of the results obtained. This will be shown in a synthetic example where the determination of the in situ stress tensor, from strain measurements in a drill hole is supposedly performed. It is assumed that this drill has its axis arbitrarily placed in relation to the rock mass. Generalised Plane Strain conditions will hold for use with problem. The equations of Beltrami – Mitchel, in agreement to Lekhnitskii (1981) and Ong (1994), will be used in this synthetic case, for calculating strains, hypothetically measured in the hole before the final excavations. Finally a synthetic example for the determination of the in situ stress in a fully anisotropic rock mass, based on Bayesian Techniques and its reliability, developed in de Mello Franco (2009) is presented."

Jan 1, 2015

By C. Morlot, C. Auvray, E. Fourreau, J. Talandier

"During the excavation of underground galleries in a rock mass, reorganisation of the stress field around the site results in damage to the surrounding material. In the framework of research undertaken at the ANDRA underground laboratory in France, galleries have been excavated in a Callovo-Oxfordian argillite formation. The damage has manifest as a number of fracture systems in the adjacent rock. Observations have shown that fractures generated during excavation and storage exploitation are able to self-seal during re-saturation of the site in the post-closure stage. Although indirect evidence for argillite self-sealing has previously been reported, from experiments performed both in situ and on samples, no direct observations of self-sealing have yet been made.For the present study, we performed a range of self-sealing experiments using a newly-developed triaxial compression cell placed within a nano-CT scanner with a 10 µm resolution. The body of the compression cell is X-ray transparent, allowing sample healing to be monitored directly. The samples contained an artificial fracture that had been generated in the laboratory, into which a fluid was injected. The fractures were orientated either perpendicular or parallel to the plane of anisotropy of the material. Our initial results demonstrate that when fluid is injected perpendicular to the plane of anisotropy, the flow-rate has no apparent influence on the kinetics of fracture closure. Permeability varies significantly, from 2.10-14 to 2.10-18 m2 over 116 hours. Post-test observations of the fracture lips show swelling that appears to be orientated perpendicular to the fracture plane and therefore parallel to the plane of anisotropy. Initial results for an injection parallel to the plane of anisotropy suggest that, in this case, the rate of flow affects the kinetics of fracture closure. For a flow-rate of 0.25 ml/min, closure begins after around one minute. In contrast, for a rate of 0.05 ml/min, it is necessary to wait several minutes before partial sealing of the zone is observed. The reduction in permeability is again significant, from 2.10-15 to 4.10-18 m2 over 96 hours. After completion of the test, swelling was observed in elongated zones that lie parallel to the fracture plane and therefore to the plane of anisotropy."

Jan 1, 2015

By J E. Curfman

This paper deals with using track-type and rubber-tired machines in the ripping and handling of overburden and ores. The techniques and proper attachments pertaining to the ripping of materials are covered in some detail. Production and relative costs of ripping, as against other methods, are covered in cases pertaining to the mining industry. The use of the refraction seismograph in predetermining the rippability of materials, including a chart relat-ing velocity to rippability, is covered. This operates on the principle that sound waves travel through subsurface materials at different velocities, depending upon the degree of consolidation of the material. It is known that the same factors that affect consolidation also affect rippability. Proper equipping of the tractor to insure maximum efficiency is also covered in some detail. Introduction T HE idea of loosening consolidated materials prior to further handling and processing is probably as old as man. The purpose of ripping is to provide fragmentation of rock and loosening of consolidated materials.

Jan 1, 1965

Flotation works very well for particles that are typically in the range 20 to 150 µmin diameter, for base metal ores. In this range, it is possible to get quite high recoveries in conventional flotation machines. Outside this range, the recoveries decline progressively, whether it be with the very fine or the coarse end of the size spectrum. In this paper, the reasons for the drop-off in recovery are briefly reviewed, together with strategies for future work. Recent progress in the author's laboratory will be described. These include the Concorde Cell, which takes advantage of the high dissipation rates in the shock wave created when a gas-liquid mixture reaches supersonic velocities. The environment thus created is very beneficial for the flotation of ultrafines. For coarse particles, the reasons for the drop-off in recovery can be related to the highly turbulent nature of the pulp in a conventional flotation cell. To improve recovery, it is necessary to find a way of bringing particles and bubbles into contact in a quiescent environment. A new process for coarse particle flotation will be described, in which a fluidized bed is created in the flotation cell. The flow conditions are very gentle, and the high solids concentration leads to rapid rates of capture of the particles. Experimental results are presented. It is apparent that the maximum floatable size for coal and minerals can be increased by a factor often over the limits found in current practice. Advances

Jan 1, 2009

By J. Dong

"A “green” collector project has been initiated at Vale Base Metals Technology Development to replace xanthate. Bench and miniplant testwork showed comparable metallurgical results between xanthate and DTC (sodium dibutyl dithiocarbamate), a “greener” collector. During the first DTC plant trial, a strong interaction between the process water and DTC negatively impacted the metallurgy. The subsequent investigation showed that the quality of process water including suspended solids and dissolved metal ions had a significant impact on the performance with DTC, while less so with PAX. This paper explains these differences using UV spectrophotometry and batch flotation tests. INTRODUCTIONVale Base Metals is dedicated to sustainable mining and mineral processing. One of the key activities is to find a “greener” collector to replace xanthate (PAX: potassium amyl xanthate), which decomposes during storage and flotation causing CS2 emissions in the work place. As the most promising candidate, DTC (sodium dibutyl dithiocarbamate) was evaluated in the lab and miniplant (Dong & Xu, 2011). Consequently, a plant trial was conducted in the winter of 2010. However, the results were not as good as expected. The subsequent investigation showed that the quality of process water played a significant role in the metallurgical performance with DTC but less so with xanthate.From test work in 1996 and 1997, a series of batch tests were performed at Clarabelle Mill to investigate the winter/summer metallurgical shift with xanthate. As shown in Figure 1, the winter metallurgy was considerably worse than the summer metallurgy (Xu & Wilson, 2000). At 80% pentlandite recovery, the concentrate (Cu+Ni) grade was 21% in the winter and 26% in the summer. At 23% (Cu+Ni) concentrate grade, pentlandite recovery was 85% in the summer and 70% in the winter. In the summer, the process water is much cleaner, with very low concentrations of dissolved metals ions and suspended solids; while in the winter, the water is yellow and cloudy, with much higher suspended solids. Based on these results, it was concluded that the process water in winter has a detrimental impact on metallurgy."

Jan 1, 2012

By Norman A. Jull

"IntroductionThe scope of this paper is intended to deal mainly with cyclones in grinding circuits. However, the section on Cyclone Equipment, contains more general descriptions, to cover most of the cyclones used in mineral separation plants.Cyclones as heavy media separation vessels are discussed by Mark Freberg (this volume). Their use in tailings deslirning is discussed by P.C. Lighthall, eta/. (this volume).Cyclone EquipmentCyclone TerminologyApexObviously, the apex of a cone is the smallest end. However, with cyclones the term is usually used for the fitting which is attached there to control discharge of the underflow stream.Note that the cyclone need not be so mounted that the apex is the lowest point, although that is the most common method. Keeping the apex below the rest of the cyclone helps avoid plugging when the underflow contains very large particles and the tonnage of underflow solids can fluctuate.Various devices for adjusting apex diameter or otherwise controlling the underflow are discussed later under ""Cyclone Construction"".BypassingThe transport of a portion of feed slurry directly to underflow so that classification is bypassed by that portion of feed.This action is fundamental in any hydraulic classification, whether gravity or centrifugal, because the large particles going to underflow have some void volume between them, which remains filled with feed slurry.D50By definition, D50 is that particle size which has an equal probability of going to overflow or to underflow.It is calculated by drawing a curve of recovery vs particle size and noting the size at which 500Jo recovery occurs.This may be done equally with corrected or with gross recovery (see below) and the resulting value should therefore be identified as d50c (corrected d50) or as d500 (gross d50).Note also that it is common in industry practice to plot size analysis data on the retained size rather than on the average of passing and retained (the middle of the size band). To portray sizing alone it makes no difference, but to read a D50 value off a curve of corrected or gross recoveries, it is essential to plot those values on the average size of each band."

Jan 1, 1989

By V. Gregoire

THE DEVELOPMENT by the Iron Ore Company of Canada of the Quebec-Labrador mining project, which eventually led to 'Iron Ore in 1954', involved, from the start, several distinct undertakings. Among them, the most important were: The construction of a 360-mile railway, linking Knob Lake with Seven Islands. The erection of a railway terminal, and harbour facilities, at Seven Islands itself. The building of an entire townsite at Schefferville (formerly Knob Lake) The construction of two hydroelectric plants; and, finally, The development of a sufficient number of orebodies to enable a production of 10 to 15 million tons of ore a year. Since these phases of the project have already been the subject of previous discussions, this paper will not elaborate further on them but will rather concern itself with a brief outline of the Company's current mining practices.

Jan 1, 1958

By T. E. Wakefield

"Final Galloway (stage) designs for vertical drill and blast shaft sinking projects evolve from complex thought patterns which integrate operational processes, systems and methods of communication, power supply, drilling, blasting, ventilating, mucking, supporting, surveying, dewatering, sealing, concrete lining and shaft furnishing. Attention to ergonomic design detail at the shaftsman / structure interface is at the heart of safe and successful multi-deck working platforms. For economy the end product must have a low mass to reduce suspension rope end loads to be able to use smaller suspension hoists and have lighter headframe structures, be robust to withstand concussion damage, be easily constructible on site, be maintainable in the shaft barrel, and comply with safety and legislated standards. This paper’s ambition is to describe a systematic design framework and sequenced thought process that delivers a product that is engineered with excellence, illustrated by making use of two designs that evolved during recent Galloway projects, one destined for a large diameter man/material shaft, the other for a ventilation shaft. The stage engineering iterative process starts with mapping permanent and sinking hoisting layouts, followed by laying out horizontal deck plans, mostly constrained by the permanent shaft purpose and configuration, whilst maximizing openings to enable muck to be removed rapidly for the best sinking cycles. Concurrently the designer needs to understand the chosen sinking methodologies in conjunction with crewing to determine the number of decks and fix their spacing. Insufficient access to move and line up formwork, set reinforcing rods and pour concrete in the confined spaces of the stage is an inherent major risk to be mitigated. An iterative and integrative process follows for the primary configuration which delves into increasing design detail, accommodating all other methodology influences, resulting in 3D layouts for further risk assessment, review and fine tuning by seasoned shaftsmen. INTRODUCTION Documented colliery shaft sinking practice from the late 1800’s makes reference to purpose built walling (bricked lining) cribs with floors suspended in sinking shafts, thereby allowing shaft lining to proceed concurrently with the excavation. Improvements were made by Sir William Galloway who introduced two decks supported at the corners by angle irons. The sinking stage, or Galloway, has developed substantially over time to be the in-barrel heart of the sinking operation, with overwhelming complexity for those who have to design one for the first time."

Jan 1, 2019

By D. J. W. Piper, T. Hundert, G. Pe-Piper

"Abstract - Potentially commercial deposits of kaolin are found in the fluvial Lower Cretaceous Chaswood Formation, the sedimentologically proximal equivalent of deltaic sediments of the offshore Scotian basin. The geological setting of the kaolin deposits has been interpreted from high-resolution seismic-reflection profiles and boreholes, and mineralogical studies on one reference borehole. The kaolin is a product of early diagenesis involving meteoric water below the water table. The distribution of kaolin is controlled by the presence of intraformational unconformities that were sites of ground water recharge, and are marked by the development of oxisols above the water table. Such diagenesis was facilitated by interbedded, loosely consolidated, permeable sandstone. The highest-grade kaolin deposits are found in areas close to river belts, where overbank muds were not sufficiently drained to develop paleosols, but where later uplift created intraformational unconformities. In the sandstone, meteoric water flow altered feldspars to kaolin, thus yielding commercial silica sand deposits. It also altered ilmenite to rutile, which is concentrated as secondary placers in modern rivers that have eroded the Chaswood Formation and tills derived therefrom. Sommaire - Des dépôts de kaolin potentiellement économiques ont été notés dans la Formation de Chaswood d'’âge Crétacé Inférieur, laquelle constitue un équivalent latéral en milieu fluviatile aux sédiments deltaïques du bassin de Scotian. Le contexte géologique de ces dépôts de kaolin a été interprété a partir de profils de seismique-réflection à haute résolution, de sondages, et d’études minéralogiques sur un sondage de référence. Ce kaolin est un produit diagénétique précoce formé par de l’eau météorique sous le niveau de la nappe phréatique. La distribution du kaolin est contrôlée par la présence de zones de recharge associées à des discordances intraformationelles marquées par le développement d’oxisols au-dessus du niveau de la nappe phréatique. La présence d’interlits de grès perméables faiblement consolidés a contribué à l’efficacité de ce processus diagénétique. Les dépôts de kaolin les plus riches se trouvent en périphérie des rivières, là ou les boues de la plaine d’inondation n’étaient pas suffisamment bien drainées pour permettre le développement de paléosols, mais où des mouvements verticaux subséquents ont crée des discordances intraformationelles. La circulation d’eau météorique dans les grès a entraîné l’altération des feldspaths en kaolin, générant ainsi des dépôts économiques de sable de silice. Elle a aussi causé l’altération de l’ilménite en rutile, que l’on trouve dans des placers secondaires situés dans des rivières contemporaines qui ont érodé la Formation de Chaswood et les tills qui en sont dérivés."

Jan 1, 2006

By P. B. Queneau, Peter V. Avotins, Lauch F. Farris

"The Lang Bay germanium property is a carbonaceous sandstone deposit outcropping near the Pacific coast, 100 km north of Vancouver. The germanium-bearing seams are up to 5 m thick. Where one such seam outcrops, it averages 50 to 60 g Ge/tonne. Drill core analyses have shown considerably greater concentrations of germanium at depth. Additional drilling to establish continuity and grade of the germanium-b earing strata is scheduled for 1986. The germanium occurs in association with lignite, which makes up 1 to 2% of the seam. American Cyanamid Company engineers have developed a proprietary flotation reagent effective for concentrating the germanium rich vitrain portion of the Lang Bay lignite. Ongoing laboratory studies are developing procedures for further upgrading and refining of this germanium. This paper outlines progress made by Fargo Oil Corporation on Lang Bay geology, reserve estimation, mine planning, ore dressing, refining, and economic evaluation.IntroductionIn 1871, Mendeleyev specula ted on the properties of a ""missing"" element between silico n and tin on the periodic table. The discovery of germanium fifteen years later proved the Mendeleyev predictions to be remarkably accurate. Almo half a century later, the pioneering work of McCutcheon of Eagle-Picher led to production of germanium dioxide from Oklahoma zinc smelting residues. Demand for the element surged due to development of the Ge02 diode rectifier during World War II, followed by development of the transistor in 1947. The chief commercial sources for germanium during the following two decades were the Cu-Zn mines in the Congo and the Zn-Cu-Pb mines of Tsumeb in Southwest Africa. The germanium was chemically combined in complex Cu-Fe sulphides (germanite and renierite), from which the element was recovered either by leaching the selectively roasted sulphide, or by direct fuming of GeS(I). Although these deposits have reportedly been depleted (2), new deposits of renierite have been discovered in Zaire. Alternative sources of germanium are therefore being sought worldwide for use in infrared optics, semiconductors, fibre optics, and catalysts. One such source is germanium-rich coal (2)."

Jan 1, 1986

By D. Campbell Mackenzie

THIS paper is submitted primarily to put on record the results of a number of experiments carried out at the Wingdam mine of Consolidated Gold Alluvials of B.C., Ltd., with the object of establishing a reliable method of concentration of 'wash' and a maximum recovery of gold from the concentrate. It will be generally admitted that, during the last two decades, a tremendous amount of research work has been carried out, both by private companies and Government departments, with a view to improving the technique of the recovery of gold .from quartz veins or lodes. So thorough have been these investigations that milling practice at a modern quartz gold mine is almost an exact science, carried out with meticulous accuracy. In placer mining, on the other hand, very little departure from old traditional methods can be noted, with the exception perhaps of the more modern gold dredges. This may be due to the fact that the concentration of placer gravels, up to a certain point, is comparatively easy. Only a simple equipment of sluice box and riffies seems necessary where the gold is coarse and the gravel free from clay. In the early days of placer mining, when claims were rich and fairly 5hallow, nobody worried very much about fine gold; and, if clay was present, an enlarged dump box was constructed in which the gravel was subjected to a rather desultory puddling. That large quantities of gold are lost in normal placer practice is generally admitted. Some 26 years ago, I had inspectorial charge of many bucket dredges on the Ovens river, in Australia. Occasionally it was necessary for a dredge to work through its own tailing to reach a new section, and almost without exception enough gold was recovered from these tailings to defray the total cost of moving the dredge. Since those days, the technique of gold recovery in dredging has been considerably improved and it is still receiving close attention. Outside of dredge mining, most placer operations, deep or otherwise, are as they were-notorious gold losers, paying little attention to the recovery of fine gold and taking an absurd amount of time over each clean-up. In the Cariboo district of British Columbia, the alluvial gold is usual y associated with varying quantities of black sand (magnetic) and grey sand (non-magnetic); and it can be taken as axiomatic that, if you save all the black sand and grey sand, you save practically all the gold. It is on this hypothesis that we have carried out our research work and brought our recovery system up to its present highly satisfactory standard.

Jan 1, 1937

By Lionel A. York

THE first application of the cementation process took place in the year 1864, according to H. Standish Ball, when a break in the brickwork lining at a depth of 270', in one of the Rhine Preussen pits near Homburg, was sealed by running in milk of cement from the surface by means of a small hand pump. At about the same time Monsieur Portier adopted the method in France for repairing breaks in shaft lining. Figure 1 is descriptive of the Portier system and is of interest when compared with modern practice. During the next thirty years numerous attempts were made to improve the process; the general method used in sinking being to put clown bore holes outside the perimeter of the shaft for the purposes of injection. The cementation process was first recognized as an important as-set to mining in 1896 when Monsieur A. Francois developed his method of boring and injecting inside the shaft below the permanent water level. The Francois cementation process rapidly attained fame on the Continent and many shafts were sunk by its use in France, Belgium and

Jan 1, 1961

By John Canterford

Quay Magnesium Limited (QMG) listed on the Australian Stock Exchange in late September 2004 having raised approximately A$30 million with the object of designing, constructing, commissioning and operating a 15,000 t/a magnesium alloy production facility in Nanjing, China, Site construction commenced in February 2005 with installation of all major components completed by the end of October 2005, Hot commissioning was simultaneously commenced with the final stages of installation, leading to the first stage of continuous ingot casting by mid November 2005, Since that time ramp-up to the name plate capacity has been undertaken, This presentation highlights some of the more significant technical and logistical hurdles that have had to be overcome in order to meet the high quality product specifications required by a range of QMG customers.

Jan 1, 2006

By C. H. van Eendenburg

"Installation of a 3.6 km long raw coal conveyor in the Balmer open pit was undertaken to improve over-all haulage efficiency. This paper covers the rationale behind this project, system design and construction aspects and initial operating experiences. The majority of the construction work was performed by our own personnel. Where feasible, used equipment was installed to reduce capital cost and facilitate a tight construction schedule.BackgroundWestar Mining Ltd's Balmer Mine is located in the British Columbia Rockies, just outside of the town of Sparwood in the southeastern corner of British Columbia. The open pit mine, which has been in operation since 1969, currently produces about 6 million clean tonnes of coal per year, mostly for the metallurgical coal export market. Run-of-mine coal tonnages total between 9 and 9.5 million annually and waste removal volumes exceed 30 million bank cubic metres.The mine is a truck/shovel operation; loading equipment includes nine electric shovels, five front-end loaders and a hydraulic backhoe. The truck fleet consists of 40 units of 154-tonne, 181-tonne and 315-tonne capacity. The newer 154-tonne trucks are used for coal haulage for which they have been equipped , with tailgates to maximize their coal carrying capacity."

Jan 1, 1990

By P. Mengé

The covering of a hydraulically filled goethite pond is discussed from a geotechnical point of view. The characteristics of the goethite were defined in order to allow a detailed study of the procedure for the construction of the cover on top of the soft material and a verification of the stability of the cover and side slopes after construction. These characteristics and the main results of the studies are given, as well as the experiences and observations made during the execution of the work. Finally, the monitoring plan, during and after construction, is also discussed and some results are given. The 'Design and Construct' contract form was used to allow the contractor to choose the optimum and most economical method to realize the closing of the pond, based on his experience with similar projects. The works were carried out between mid 2003 and the end of 2004. The paper will, amongst others, discuss the special method of working that had to be developed to allow the covering of the whole pond in a relatively short time period, without soil improvement methods such as vertical drains or stabilization by in situ treatment. Fill material was used to establish a platform on top of the soft material so that the cover liner and finishing layer could be installed on top of the fill layer. The 'floating roof' principle was used; subsidences were allowed to occur during the installation of the impermeable top liner and soil cover.

Jan 1, 2006