Search Documents

By M. W. Grabinsky, B. D. Thompson

ABSTRACT: Use of cemented paste backfill (CPB) offers economic and environmental advantages over other backfill methods. However, many operations have limited knowledge of how their CPB behaves in situ. Therefore, to avoid over-pressuring containment barricades, backfilling strategies necessarily tend to be conservative. In situ monitoring at Barrick Gold Corporation’s Williams Mine and Inmet Mining Corporation’s Cayeli Mine has been conducted and factors controlling barricade pressures are demonstrated, including rise rates, binder content, stope geometry, and tailings properties. The application of barricade pressure monitoring on a stope-by-stope basis can increase backfilling efficiency and, thus, reduce stope cycle times, while maintaining optimal safety.

Jan 1, 2011

By D. Pacey

"This paper reviews the installation, start-up, and operation of a comprehensive monitoring and targeting management technique in which all plant utilities (i.e., electricity, natural gas, compressed air, and water) are managed as controllable resources in the same way that raw materials, mined ore, personnel and capital are managed.The essential elements of monitoring and targeting (M&T) include:•gathering in a systematic, disciplined way the utility information by energy account centres;•closely monitoring the utilities used in each centre and comparing them with production on a common time base (e.g., kWh/ton per day);•bench marking and target setting to pro-vide attainable energy reduction goals which can be further refined as they are achieved; and•establishing an implementation plant that may provide efficiency enhancing benefits to various operating areas within the plant.The M&T system will reduce utility consumption per unit of production on a continuing basis.This would translate into sustained operating cost and waste. M&T will also provide better information for assessing the plant operation and progressively implementing further enhancements."

Jan 1, 1997

By J. Visman

"The Compound Water Cyclone is a concentrator for the wet processing, in bulk, of finely divided materials such as slack coal, fine ores and mineral sands. It was originally developed by the Fuels and Mining Practice Division of the Mines Branch, Department of Mmes and Technical Surveys, Ottawa, for the cleaning of friable slack coals and slurries.Since its introduction in the coal industry in 1962, its application to other materials has also been studied, with special emphasis on simplicity of operation and low over-all cost per ton of finished product .In this paper, a description is given of commercial two-stage units presently available for the processing of granular materials, including wastes a1:1d other low-grade products. A pneumatic control system is used for operating the cyclone under back pressure .and for automatic cut-point adjustment. An account is given of results obtained on coal mineral sands and ores in the Wes tern Regional Laboratory of the Department of Mines and Technical Surveys. Results of several industrial applications are discussed."

Jan 1, 1966

By Margaret Anne Stephenson

Today, in Australia, it is increasingly common to see agreements between Indigenous peoples and resource companies being achieved generally as Indigenous Land Use Agreements or agreements pursuant to the ?right to negotiation? process under the Native Title Act 1993 (Cth). Despite progress in this area, resource development on Indigenous lands is not without its challenges for both the resource proponents and the Indigenous parties. History demonstrates that resource development on Indigenous lands has produced struggles between the traditional owners of the land and the resource proponents. In Australia their relationship is generally defined by issues of access to land and assuring continued access to the land for the life of the project. In this context, divisions in Indigenous communities often emerge. The proposed resource project can have the effect of polarising members of an Indigenous community. It may be regarded by some traditional land owners as an advantageous opportunity for the community and by others as a hazard to country and culture. The process of agreement making has proved not only a test for the Indigenous community but also for the resource proponent. In this paper we undertake a contemporary case study of a proposed Australian resource related-development project on Indigenous lands. This project involved a multi-billion gas hub precinct proposed at James Price Point in the Kimberley region in Western Australia. The James Price Point proposal produced a litany of challenges for all parties. The traditional owners faced fundamental social and human rights issues, including a minority opposition to the project, the project's potential cultural heritage impact, the threat of compulsory acquisition of their native title interest by a State government due to an initial failure to settle an agreement, a fracture of their unsettled land claim and a minority rejection of the agreement ultimately reached. Additionally, the ?green? lobby also rejected the proposed gas hub on environmental grounds bringing the green lobby into direct conflict with both the traditional owners in favour of the project and the resource proponent. Ultimately, Woodside announced its decision not to proceed with the proposed gas precinct at James Price Point, in April 2013. In this paper we analyse the complexity of the James Price Point gas hub negotiations with the traditional owners which resulted in an Agreement that promised to deliver substantial benefits for the Indigenous communities. We question why such a favourable and beneficial agreement for the Indigenous community also produced the plethora of challenges and concerns and we consider how future negotiation processes could be better structured to avoid the difficulties that have confronted Indigenous land owners and resource proponents alike.

Aug 1, 2013

By N. V. Mel'nikov

This paper discusses the reserves of oil, natural gas and coal in the USSR, with particular attention to the future role to be played by coal in supplying the energy fuel resources of the country.

Jan 1, 1972

By Xiao min Zhou, Yan Xu, Hongzhen Liang, Xiaonan He

"With the increase of shaft excavation depth, the thickness of the shaft lining increases sharply. It is difficult to reduce thickness of lining effectively by improving high-strength concrete performance. The concept of the New Austrian Tunneling Method (NATM) is that surrounding rock plays a certain role in tunnel support. The solution should be to find the correct relationship between shaft lining thickness and rock strength, which is related with the interaction between the surrounding rock and concrete lining. The plane strain mechanics model is introduced to calculate lining thickness. Shaft lining design of Cixi Colliery in China is completed with the mechanics-based method proposed in this study. The lining design is verified through numerical simulation and field monitoring. The simulation results show that the maximum mises stress is located at the inner edge of the shaft lining. The increase of lining thickness cannot effectively reduce concrete grade. The monitoring results indicate that a lining design thickness of 900mm with C60 concrete, is safe and reliable in the shaft over 1000metres.This analytical design method can well be referenced in similar deep shaft projects.INTRODUCTION The New Austrian Tunneling Method (NATM), thought to have helped revolutionize the modern tunneling method, is the most extensive design philosophy and construction principle in today's tunnel engineering. It began to attract attention in the 1960s based on the work of Ladislaus von Rabcewicz, Leopold Müller, and Franz Pacher in Austria[1]. NATM was originally developed for tunneling in depth and in high situ-stress conditions in the Alps. The history of sequential excavation was reviewed, which highlights the progress of tunnel design and construction in Europe after NATM[2]. Structural conditions were introduced into the equilibrium of tunnels in NATM, and the additional force was estimated to stabilize the excavation of the tunnel[3].From the perspective of applied mechanics, there was no accuracy theory to explain the interaction between the tunnel structure and the surrounding ground. Numerical calculation is an effective means to study the basic mechanism of tunnel excavation[4].Based on two-dimensional modeling approaches in the past, such as NATM and other derivatives, a three-dimensional model was studied to"

Jan 1, 2019

By P. Favreau

"This paper describes the progress accomplished at the Noranda Technology Centre in the field of three-dimensional computer-aided underground blast design. Traditional methods of laying out underground blasts are reviewed, and the new computer-aided approach is described. Time savings achieved through the use of BLASTCAD can be advantageously used to better engineer blasts, using models and blast vibration analysis. Future work involving the attachment of blast models directly to the system is also addressed.IntroductionThe Noranda Technology Centre's (NTC) Environment and Mining Laboratory, in cooperation with the mining operations of the Noranda Group, is committed to the development and implementation of new technologies in the field of mineral extraction . Within the frame of its research program, the Blasting Technology Program is developing computer "" tools"" designed to assist the blasting engineer or technician. These computer "" tools"" are regrouped under a global software system called BLASTCAD.The BLASTCAD project started in 1990 at NTC. At that time computer programs designed to calculate and model various blasting parameters had been accumulated. These programs cam e from different sources and were mutually incompatible. Furthermore, they were developed as research programs with tittle effort spent on user interface. These programs are very useful, but are highly specialized, need large input files and can be quite tedious to use as ""standalone"" packages .Therefore, the situation being faced was one where all these programs were available at the Noranda Technology Centre, but not a t the operations. The two following options were then considered: 1. continue to run all the models and programs at the Noranda Technology Centre, and present results through reports to the mines, or2. regroup all the different programs under a single one that would make them share the same data base and be transported to the user. This second option is the one that was adopted; the result is BLASTCAD."

Jan 1, 1993

By Louis Cabot

A pilot plant of the Modular Gold Processing Unit (MGPU) was designed, installed and operated, over a 8 months period, by RSW-Béroma, at the Granada Mine located near Rouyn-Noranda, Quebec. A description of the project geology, plant set up as well as exploitation results, including productivity and profitability curves, are given for a small scale mining operation in comparison with larger ones. Copyright ã 2001 CIM

May 1, 2001

By V I. McCallum

In 1954, Falconbridge Nickel Mines Limited began the program of deepening the Falconbridge mine workings for 2,000 feet below the bottom, or 4025, level in order to provide twelve new levels for production. Involved in this program were a production-sized internal shaft, .crushing, pumping and hoisting installations, the integration of the new shaft operations with those of existing shafts, and considerations of ventilation requirements and ground support at depth. This paper describes the major items of equipment, and the depth development of No. 9 shaft as a whole, and also emphasize the planning phases of the program. The factors involved and reasons for the equipment and layouts chosen are given. Introduction and History THIS paper describes the planning and development of that portion of the Falconbridge mine between the 4025 and 6050 mining levels. This mine, the oldest of several being operated by Falcon-bridge Nickel Mines Limited in the Sudbury district, has been a continuous producer for over thirty years.

Jan 1, 1964

By C. S. R. Rondestvedt

In February 2010, Teck?s newest Concentrator at Mina Carmen de Andacollo (CDA), Andacollo, Chile was commissioned. The Concentrator is a single line configuration, comprising of one 36 ft diameter x 20 ft long SAG mill driven by an 18,000 hp gearless drive. The SAG mill feeds two ball mills each 25 ft in diameter x 40.5 ft long, each driven by a total of 19,000 hp through dual pinion drives. A series of four phases will be reviewed from operational readiness, mechanical completion, commissioning, and ramp-up. Also, now after 6 months of operation, this paper will review the significant steps taken during ramp-up enabling the announcement of commercial production, in October 2010.

Jan 1, 2012

By Waldemar W. Koczkodaj, William O. MacKasey

Abstract - A consistency-driven pairwise comparisons method for mineral potential assessment is presented, using a simplified case of volcanic-associated massive sulfide type deposits as an example. Geological, geochemical, and geophysical criteria are considered on two levels: local and regional. The local geological criteria are subdivided into stratigraphy, lithology, alteration and/or mineralization, and structure. The concept of geomerit index and a procedure for computing this index are introduced. The method of consistency-driven pairwise comparisons can be combined with other quantitative and qualitative assessment methods, enhancing them by incorporation of nonmeasurable geological criteria (e.g., stratigraphy or lithology) and by computation of weights. The consistency-driven approach allows experts to refine at-times subjective judgments concerning exploration and land-use planning, and contributes to the improvement of mineral-potential assessments.

Jan 1, 1997

By Waldemar W. Koczkodaj, William O. MacKasey

A consistency-driven pairwise comparisons method for mineral potential assessment is presented, using a simpli?ed case of volcanic-associated massive sul?de type deposits as an example. Geological, geochemical, and geophysical criteria are considered on two levels: local and regional. The local geological criteria are subdivided into stratigraphy, lithology, alteration and/or mineralization, and structure. The concept of geomerit index and a procedure for computing this index are introduced. The method of consistency-driven pairwise comparisons can be combined with other quantitative and qualitative assessment methods, enhancing them by incorporation of non-measurable geological criteria (e.g., stratigraphy or lithology) and by computation of weights. The consistency-driven approach allows experts to re?ne at-times subjective judgments concerning exploration and land-use planning, and contributes to the improvement of mineral-potential assessments.

Jan 1, 1997

By D. S. Campbell

THE chief factors influencing the decision to build the Big Missouri mill underground were the topography of the country and the climate. The location underground assured certain saving in the cost of operation, such as the hearing of the mill, shovelling snow, and handling ore, which, over a period of time, would offset the greater initial cost of the mill excavation and machinery installation underground, as compared with the cost of a like plant on the surface. At Gilman, Colorado, where conditions are somewhat similar, the Empire Zinc Company, at their Eagle mine, are treating their lead-zinc ore in a mill built entirely underground. Company officials made a study of this plant before proceeding with the mill at Big Missouri. LOCATION, CLIMATE, TOPOGRAPHY The Big Missouri mine is situated on the Upper Salmon river, 22 miles north of Stewart, B.C., which is at the head of Portland canal, a narrow natural channel which penetrates 100 miles inland from the coast into the Coast Range mountains. Stewart, the distributing centre for the district, is about 600 miles north of Vancouver. The Big Missouri claims lie on and down the sides of the Big Missouri ridge, which extends north and south between the Salmon River and Cascade Creek valleys. The ridge rises to an elevation of 3,600 feet, is about half a mile wide, and to the east slopes down to the Joker flats in Cascade Creek valley. The Big Missouri camp is located on the flats at elevation 2,800 (see Figure 1). Preliminary development of the property took place from this point with an adit driven under the ridge. The western side of the ridge slopes steeply down to the Salmon glacier at elevation 1,900. Ore found on the 2,850 level extended down, and, in order further to explore the ore-body, the 2,850 level was driven through to the west side of the ridge, a surface incline tramway was built, and a lower tunnel driven at elevation 2,350, five hundred feet below the original 2,850 level, from the west side of the ridge. This tunnel development avoided the necessity of sinking, which would have been costly, as the mine makes a great deal of water (see Figures 1 and 2).

Jan 1, 1938

By G. Capobianco

"The coal industry is an important part of Canada's economy - as an energy source, employer, and generator of export earnings. Coal comprises 71% of our fossil energy and with rapidly advancing handling and burning technology will clearly play a major role in our national energy mix, eventually as synthetic gases and liquids.International coal markets are very competitive and Canada is disadvantaged by long rail hauls to port, and a heavy tax burden. However, high mine productivity has allowed us to increase our markets.Currently, domestic markets are dominated by coal use for electrical generation, a market with significant growth opportunities.Strong growth is expected in export thermal markets, while metallurgical coal demand is projected to show little or no growth in the medium term. IntroductionThe coal industry is a vital part of the Canadian energy scene .• Coal supplies 17% of Canada's energy.• On a per capita basis, Albertans use more energy in the form of coal than they do oil and gas.• The value of Canada's exports of coal last year was equal in value to all the cars we imported from Japan.• Coal is our largest single export to our seco nd largest trading partner, Japan.• The value of coal produced in Canada exceeds the value of any other single mineral produced in thi s country.• In Alberta, the safety record for coal mines is on a par with that of department store clerks.• The coal industry employs about 25% of the total number of people employed in all metal mines in Canada, directly and indirectly accounting for about 50 000 jobs.Coal comprises 71% of Canada' s hydrocarbon energy resources on a crude oil equivalent basis . This is more than double our oil sands resource and dwarfs our conventional crude oil and gas resources (Fig. I). In the short term, coal as a solid fuel plays a significant part in the Canadian energy scene. In the longer term, coal, in the form of electricity and eventually liquids and gases, has a tremendous role to play. In 1986, Canada produced 57.8 million tonnes, slightly down from the record high of 60.8 million tonnes in 1985. Our exports in 1986 were 26.0 million tonnes, a growth of 53% in three years."

Jan 1, 1988

By Fan Delian, Ye Jie, Lui Tiebing

The lower and the upper parts of the Doushantuo Fonnation, Hubei Province, China, contain silicate-type K-rich beds (illite and feldspar), and intraclastic phosphorites, as well as Ag-V and V deposits in a "Black Shale Series". The K-rich beds fonned in an anoxic basin whereas the phosphorites fonned in a more oxic and higher energy depositional environment. The Black Shale Series occurs in the lower and upper parts of the Doushantuo Fonnation; that in the upper part consists of black illite shale and dark gray dolostone, and contains Se-rich Ag and V deposits. These deposits are of more industrial significance than the previously discovered Ni-Mo polyelement sulfide deposits which occur in the Lower Cambrian Black Shales Series of South China. Studies of lithotype, sedimentary sequence, and geochemistry of the Doushantuo Fonnation have led to more attention being focused on the uppennost Black Shale Series and its Ag-V and V deposits. There are three ore types: black, Ag-V-rich, illite shale; black, V-rich, illite shale; and dark gray, Ag-Vrich, fmely crystalline dolostone. The first two ore types contain 3070 to 5% Corg and the last, 1.25%. The Ag-bearing minerals are naumannite, argyrodite, aguilarite, acanthite, and native silver that occur as inclusions in pyrite associated with barite. Vanadium substitutes for AI in illite and is also related to organic-matter contents. Because (1) the pre-Sinian Kongling Group contains one to three times greater than the Clark Ag value; (2) black, illite shale has a negative Ce anomaly; and (3) there are large occurrences of black, K-rich, tuffaceous, fme siltstone, the sources of Ag are thought to include subaerial and submarine volcanic materials. It is proposed that Ag, V, and Se were absorbed by clay particles and organic matter during syngenetic deposition in an anoxic environment; Ag subsequently was reconcentrated into sulfides and selenides, whereas V was incorporated structurally into illite during early and late diagenesis. These types of Black Shale Series-hosted Ag-V and V deposits are, therefore, considered to be sedimentary-diagenetic in origin.

Jan 1, 1992

By M. Stogran-Baker, E. Legault-Seguin

"Fluorspar mining in the St. Lawrence area of Newfoundland and Labrador began in the 1930s and ended in the mid-1980s. In 2013, Canada Fluorspar (NL) Inc (CFI) discovered a new ore body, the AGS vein, which proved amenable to more economic open pit mining methods and began developing this resource. This paper discusses the flowsheet development of the AGS vein deposit. Testing at SGS began in 2009 with samples from other deposits in the area. The testwork included pilot-scale dense medium separation (DMS), laboratory-scale flotation tests to develop the flowsheet and a flotation pilot plant. The more recent work that is presented here has been devoted to the AGS vein, and included a variability testing program that gave tremendous insight into the metallurgical drivers of processing the deposit. The ore was found to be fairly variable in terms of fluorite grade, but also gangue mineralogy, which had greater implications on the DMS performance. The gangue mineralogy was also found to significantly impact the grindability characteristics of the DMS product. This paper will detail the testing conducted and the mitigating steps which were identified for the operation.INTRODUCTION Fluorspar is the industrial trade name for the mineral fluorite (CaF2), which is the primary industrial source of fluoride. There are a number of categories of fluorspar, most notably acid-grade fluorspar and metallurgical fluorspar (metspar). Acid-grade fluorspar has stringent specifications and is suitable for the production of hydrofluoric acid that is used for many applications. The typical specifications of acid-grade fluorspar are >97% CaF2 and less than 1% each of SiO2 and CaCO3, with a particle size distribution in the order of 80% passing 100 µm. Metspar is typically used for metallurgical purposes, typically as a flux in smelting, and has significantly more relaxed specifications (< 15% SiO2). The principle source of fluorspar in Canada has been from the Burin Peninsula in Newfoundland and Labrador. More than 3 million tonnes of fluorspar were produced there between 1940 and 1978 and from 1987 to 1990, when production ceased (Fulton & Montgomery, 1994)."

Jan 1, 2018

By Riggin P. R.

"IntroductionIndustrial Relations combines two very important relationships - employee relations and union relations.Employee relations always come into play when people are hired to perform tasks. Because mineral processing plants cannot be operated successfully without people, at least not yet, if they ever will be, employee relations must exist in an operatingplant.If the employees choose to be represented by a union, then a relationship with the union as an institution also comes into play. It is very important to note that unionization does not mean that the employee relationship is replaced by a relationship with the union. The latter is superimposed on the former, but it does not replace it. Similarities and overlaps in the two relationships will be present, some of which are of fundamental importance. Nevertheless, they are two different relationships and the reader should bear this in mind when reviewing those parts of this chapter which discuss unionization, collective bargaining, collective agreements, and work stoppages.These two important relationships, which we have chosen to combine and call industrial relations, have crucial roles to play in the social system which interrelates people performing the necessary tasks involved in the operation and maintenance of a plant. The technological organization - equipment, process layout and so forth - and this social system are interdependent and complementary. This chapter attempts to show that the potential level of effectiveness of both the technological organization and the social system depends on the recognition and nurturing of this nexus between them.Occupational health and safety and training are subjects for another chapter. But, both of these have been critical and longstanding employee relations topics . They are destined to take on added importance in the future. As issues in collective bargaining, they are also attracting increasing attention in all union relations. It is hoped that the reader will not isolate from industrial relations those topics which are being dealt with in another chapter. They are very much a part of it and we cannot refrain from making some reference to them."

Jan 1, 1989

By T. C. Cheng, G. P. Demopoulos

It is the object of this paper to discuss various options for improving the hematite process in terms of increased throughput hence lower capital cost and production of saleable quality hematite. With reference to increasing the throughput of the process, it has now been determined via the analysis of Akita Zinc Co&apos;s continuous industrial autoclave performance data that the process kinetics is limited by the rate of the hydrolytic precipitation reaction. By correlating the hydrolytic precipitation rate to supersaturation ratio, it is shown that accelerated kinetics can be achieved via the following measures: (1) in-situ neutralization with addition of zinc calcine; (2) elevation of temperature; and (3) dilution of feed; of which, the first one was retained for further evaluation. According to presented estimates, addition of calcine, amounting to only 2.6% of the total zinc calcine processed, can allow for shortening the retention time by at least 50%. Such drastic shortening of retention time may be either used to increase the throughput of a given autoclave circuit or alternatively to release autoclave capacity for clean hematite production. Hydrothermal treatment of the crude hematite product proved effective in producing clean hematite as according to laboratory tests, hence allowing the sulphur content of hematite to be reduced from around 4% to less than 1%. A conceptual flowsheet incorporating in-situ neutralization for accelerated kinetics with hydrothermal upgrading of crude hematite without sacrificing production capacity and with minimum upset of the plant&apos;s water balance is described.

Jan 1, 2004

By John J. Barakso

A summary of geochemical dispersion processes is presented. Secondary and tertiary dispersion of uranium was examined at several uranium prospects in British Columbia. The vertical migration of uranium from bedrock (primary dispersion) through overburden into the various soil horizons, and into snow and plants, was studied, and relationships were sought to explain the dispersion patterns in the secondary and tertiary environments. Soil developments were examined to obtain information on factors affecting the dispersion of uranium in soil profiles and tertiary substances; samples were analyzed for a number of elements. Biogeochemical data indicate that plant geochemistry is a possible exploration aid in areas of heavy overburden owing to the high selectivity of certain plants for specific elements. Some new data on the geochemistry of snow are discussed as a matter of research interest in the tertiary dispersion of uranium. Analytical techniques and problems are discussed, particularly extraction techniques, which must be carefully chosen to give reliable information on uranium dispersion.

Jan 1, 1979

By Henri-Loui Jacob, Suzie Nantel

"Depuis la fin des annees 1800, la province de Grenville represente pour Ie Quebec une source importante et diversifiée de minéraux industriels. Le Ministère de l&apos;Énergie et des Ressources du Québec, dans Ie cadre de I&apos;entente auxiliaire Canada-Québec, et les compagnies minieres y ant multiplié, surtout depuis 1983, leurs travaux d &apos;exploration, de cartographie, et d&apos;évaluation pour les minéraux industriels. Ces travaux ant conduit ala découverte et ala mise en valeur de gisements de granite architectural, de graphite, de dolomite et ant aussi permis de repertorier des gîtes et des indices prometteurs de wollastonite, de silice, de calcite. de dolomite, de silicates d&apos;alumine et de terres rares. Les gisements récemment découverts sont actuellement exploités au sur Ie point de l&apos;être et les gîtes et les indices les plus prometteurs ant été jalonnés.ABSTRACTSince the late 18oos, the Grenville Province in Québec has been an important and diversified source of industrial minerals. The Ministere de l&apos;Énergie et des Ressources du Québec, under the Canada-Quebec Mineral Development Agreement, and the private sector have put an emphasis on exploration, mapping and evaluation programs in the Grenville Province for minerals, particularly since 1983. These programs have led to the discovery and the development of deposits such as architectural granite, graphite and dolomite, and have also led to inventories of occurrences and prospects of wollastonite, silica, calcite, dolomite, alumina silicates and rare earths. The deposits discovered lately are presently being quarried or will be in the near future. The most promising occurrences and prospects have been claimed."

Jan 1, 1990