Search Documents

By Watters R

Modem open cut and underground mining in the tropics inevitably expose partially weathered and unweathered rocks to oxygen and water, leading to weathering and the release of solutes and often acidity as well. Historical monitoring data can demonstrate these phenomena. Three case studies from open cut mines in the north of the Northern Territory illustrate the deterioration in quality of pond water receiving drainage from waste rock dumps. The potential for deterioration of water quality was not recognised in many mine Environmental Impact Statements prepared and accepted in the 1980s. The examples documented indicate the importance of adequately planning for this near inevitable process. Retrofitting a mine water management system to 'no' or minimal release can be very difficult and expensive, and may not be feasible, leading to downstream pollution. The characterisation of acid and solute production potential of ore and waste rock, and improved dumping strategies and water management are very important to minimise the environmental impact of mining in the tropics.

Jan 1, 1994

In the course of an investigation of the influence of bismuth on copper carried out some years ago, (1) the author found that phosphorus exerted a beneficial effect on bismuth-copper alloys of low bismuth and oxygen content by neutralizing the embrittling effect of the bismuth. In the intervening years, a further examination of bismuth-phosphorus-copper alloys has been canied out and the influence of other elements and combinations of elements on copper containing bismuth has been studied.The results recorded in the present paper are part of this investigation.MATERIALSAll the alloys were made from high-grade copper (KS.A. wire-bar) of the following composition: copper 99·95%, oxygen 0,040'%, iron 0·0015%, sulphur less than 0-001%, bismuth less than (j>'OOl%, other elements each less than O· 0010/<-. The bar was hot rolled and cold drawn to strip which was cut into short lengths and cleaned in nitric acid ready for melting.A piece of this 'strip was drawn to wire 0·08 in. diam., annealed at 5000 C, and measured for electrical conductivity as a check on purity. The result was 101·5% of the I.E'.C. standard.In making the alloys, phosphorus was added as 14% phosphor-copper, bismuth as 17% bismuth-copper, and the other constituents either as copper alloys or as elements of a high degree of purity.PREPARATIQN OF STRIPSThe charges were melted in plumbago crucibles (Morgan salamander brand) in an oil-fired furnace, Le;, in the manner commonly adopted in industrial practice. The copper was first melted under charcoal, well stirred with a chaned stick, and the necessary alloying elements added and stirred in with the stick. The weight of a charge varied according to requirements but generally was about 4 lb. The charges were poured into slightly tapered brass moulds heated to about 1000 C and dressed with a mixture of mineral oil and tallow. They were not only poured under charcoal through the burning mould dressing but also- through a ring of flame produced by burning kerosene on asbestos cord wrapped round the top of the mould. Experiments carried out with plain copper proved that by this means oxygen could be excluded from the stream of metal. The billets were 7·5 in. long x O·83 in. diam. x 1·3 lb. weight.The billets were cropped about 1 in. from the top, cleaned in nitric acid, and measured for density by the usual method of weighing in air and -in water. As these measurements were required only as a check on casting, technique a high degree of accuracy was not essential (accuracy = -+ 0·2%).

Jan 1, 1942

By Totterdell JM

The Permian-Triassic Bowen Basin and the Jurassic-Cretaceous Surat Basin evolved in a backarc tectonic setting behind an active convergent plate margin in eastern Gondwana. Several extensional (Early Permian; Eocene) and contractional (mid- Permian; Early Triassic; Middle-Late Triassic; early Late Cretaceous) intraplate deformational events are recognised in the basins. These can be correlated with similar events in the New England Orogen that was being deformed in the Late Permian- Late Triassic as a foreland thrust belt. The intraplate deformations were probably the consequence of plate interactions, including the accretion of terranes, at the ancient active plate margin, remnants of which now occur in New Zealand.

Jan 1, 1995

By P R. Lock

The Silver Swan nickel mine is located at the Black Swan Nickel Project, 53 km north east of Kalgoorlie, Western Australia. The Silver Swan orebody is a massive sulphide nickel deposit dipping 70¦ east with an average in situ grade of 14 per cent. Mining of the massive orebody is by Mechanised Ramp Cut and Fill (MRCF). A mining recovery of 98 per cent and minimising dilution are primary goals in extracting the high-grade ore. Placing a distinguishable marker bed (working platform) on rock fill was identified as a key method to achieving these goals. Gravel from a pit located onsite was considered the most suitable material for the marker beds. Research undertaken to design the marker beds using the gravel revealed conventional methods used in mining would not suffice, but that road stabilisation methods could be a viable alternative. Trials used a road recycler to mix cement and gravel in situ and several test beds were constructed on the surface to determine the final design. The trials attempted to replicate a marker bedÆs life cycle of construction and placement and mucking of ore from the marker bed. Testing the marker bed for strength for use as a working platform was completed using a Clegg Hammer; good correlation to a Clegg Impact Value and the compressive strength of the stabilised gravel was found. This paper describes the use of a road stabilisation machine, tests conducted, monitoring and marker bed design and discusses underground placement of the marker bed and its performance.

Jan 1, 1998

By Z Li, Z Yan, M Yang

Recycled cement paste (RCP) is a kind of CaO-rich recourse, which is separated and recycled from waste concrete. Due to its chemical composition, RCP could partially replace lime as a flux and be loaded into electric arc furnace (EAF) steelmaking process. Rapid RCP assimilation and liquid slag formation have significant effects on EAF steelmaking process. In this study, the dissolution behaviours of RCP and lime at temperatures of 1400°C to 1500°C were investigated using static dissolution experiment. The dissolution rate, interfacial microstructure, as well as dissolution mechanisms were discussed. It was found that the dissolution rate of RCP was much higher than that of lime. RCP could be completely dissolved into slag in 60 secs at 1500°C. The dissolution rate of lime was in range of 3.910-4 g/(cm2ꞏs) to 2.610-3 g/(cm2ꞏs), while that for RCP was in range of 1.510-3 g/(cm2ꞏs) to 4.910-3 g/(cm2ꞏs). As for lime dissolution, a dense layer of dicalcium silicate (C2S) generated at the dissolution interface, and the diffusion of Ca2+ in C2S layer was the limited step for lime dissolution. Some of calcium ferrite could be observed at the interface between lime and C2S layer. As for the RCP dissolution, there is no obvious product layer of C2S formed at the dissolution interface, Fe2+ continuously diffused into RCP layer during the dissolution, and small amount of FeOꞏMgO solid solution generated and gathered at the dissolution interface. The dissolution rate of RCP in EAF slag was quite higher than that of lime, partially add RCP as flux in EAF could accelerate the slag formation process.

Aug 21, 2024

Equilibrium in the reaction H2(g) + [%0] (in liquid copper) = H2O (g) was investigated at temperatures between 1200 -and 1350°C with p(H2Oj/p(H2) ratios between 1 to 15. A semi-microbalance was used for direct measurement of dissolved oxygen in molten copper. Oxygen was found to obey Henry's law under the experimental conditions used. The standard free-energy change for the above reaction is given by Equation 1where 1 weight per cent solution is the standard state for dissolved oxygen.For the dissolution of oxygen in copper according to 1/2 O2(g) = [%0] (liq. Cu), the standard free energychange is given byEquation 2.

Jan 1, 1973

By Callaghan T

The Henty Gold Mine is located approximately 30 km north of Queenstown, at the head waters of the Henty River on the west coast of Tasmania at 41¦50'S, 145¦40'E on the Queenstown (SK 55-5) 1:250 000 and Sophia (8014) 1:100 000 map sheets (Figure 1). The mine is accessed from Queenstown along the A10 Highway and Anthony's Road. The town of Queenstown is located 260 km north west of Hobart on the A10 Highway, and

Jan 1, 1997

By J St George

Much of AucklandÆs transport infrastructure has been developed on surface with little or no consideration of underground options. Current and planned transportation routes are now facing high costs due to land values and increasing environmental resistance to surface development. The option of utilising underground space becomes a feasible investment decision for these links as well as being the only option to develop the rail network within the inner city area. Transportation tunnels offer a quieter, more energy efficient means of getting around with minimal impacts on the surface environment. One of the major impediments to tunnelling is the high construction cost, which is partly related to the risks of encountering unexpected ground conditions and/or the possibility of causing surface ground deformations which could damage structures. The geology of Auckland has had substantial investigation through various studies and projects. The sediments of the East Coast Bays Formation (ECBF) underlie most of the Auckland urban area. It is classified as a soft rock and is a suitable material to tunnel through using either a tunnel boring machine or a roadheader. This paper reviews the limited amount of tunnelling completed in the urban Auckland area, together with the international advancements that have been made in the tunnelling industry. From the known features of the local geology and the problems encountered historically, the likely risks of tunnelling in Auckland are presented and ways in which those risks could be reduced and managed, are discussed. In addition, contractual arrangements between client and contractor are assessed with respect to complicated projects (such as tunnelling), so that the risks can be managed to create efficient infrastructure routes with reduced costs.

Jan 1, 2008

By J Chßvez, J Rosa del Castillo, J Rui

Environmental Impact Assessment (EIA) and Feasibility Studies (FS) were carried out to evaluate the potential use of treated acid mine drainage (AMD) occurring at the Kingsmill Tunnel in the Central Andes of Peru. The 11 km long tunnel drains the underground works of the Morococha Mining District and discharges about 1.25 m3/sec of AMD directly into the Yauli River in the Amazon Basin. The communities living downstream cannot use the Yauli River water due to its low pH and elevated concentrations of metals (eg Cu, Zn, Fe, Mn, As, Cd) and sulfate. Studies carried out for this project included technical feasibility, EIA, economic viability and social impact assessment phases. During the æTechnical FeasibilityÆ phase, the treated AMD was produced by simulating a high density sludge (HDS) lime neutralisation/ precipitation process and was evaluated for various potential uses. Mining companies located in Morococha, in particular Centromin Peru SA, and the Water Works Company of the City of Lima (Sedapal) collaborated with Golder Associates during the studies. The Canadian International Development Agency (CIDA) provided the financial assistance. The results of the physical, chemical, biological and toxicological analyses demonstrated that the AMD could be sufficiently treated to be potentially used to supplement the drinking water supply of Lima, and for agricultural (eg irrigation and livestock) and recreational purposes. Process design and scale-up parameters were also determined for implementation of the full-scale treatment facility at the site. The use of the treated AMD as a drinking water supplement would be economically feasible.

Jan 1, 2003

By J Plinke

The imperative to operate sustainably requires all equipment and processes to operate at their maximum possible efficiency. Achieving this ideal state requires a thorough understanding, not only of the process itself, but also of the tools available to design and assess potential improvements. This paper presents a case where the widely employed Discrete Element Method (DEM) toolset proved insufficient to model problematic material flow during the process of optimising wet screening performance. A Smoothed Particle Hydrodynamics (SPH) model was found to more accurately replicate the flow characteristics of the physical system. Site observations identified biased loading of the screen decks to cause inefficiencies in the wet screening of an iron ore processing circuit. Two numerical modelling approaches were pursued with the aim to select the most suitable one and continue the optimisation process based on that selected model. Selection criteria were established, based on the minimum requirements of being able to replicate the problem, including the main flow dynamics deemed to cause the issue. The DEM model was found to over-simplify the slurry flow dynamics within the scrubber and no laterally biased flow was introduced by the scrubber’s rotation to the otherwise symmetric system. Since DEM was not able to accurately replicate the existing problem, it was deemed an unsuitable method to assess the effect of any changes to the system. The second approach consisted of a SPH model. This model was deemed to map the flow within the scrubber with sufficient accuracy to address the problem, as it produced biased screen loading comparable to that reported from site. Changes to the wet chute, delivering material from the scrubber to the screen, aimed to neutralise the non-centrality introduced via the scrubber, were then successfully designed and assessed using the SPH model.

Nov 8, 2021

By Lean P. J

The present The Zinc ODrporation, Limited and New Broken Hill Consolidated Limited (ZC/NBHC) tailing dam (Site C) is expected to reach its terminal capacity late in 1985. Planning and design of new facilities for disposal of tailing after 1985 which includes new tailing dams (Site D) commenced during 1980. This paper briefly describes planning guidelines and specifications, location considerations, environmental aspects, operating strategy, engineering specifications, envirormental aspects and scheduling of works.

Jan 1, 1983

By I Basson, J A. Miller, M Becker, F C. de Beer, L C. Bam

"Geometallurgy brings together geologists, mine planners and process engineers to extract meaningful mineralogical and textural information from an orebody, with a view to predicting its metallurgical response. Preferably, automated analytical techniques, which provide mineralogical and textural information, should process a large number of samples quickly, relatively inexpensively and reliably. Microfocus X-ray computed tomography (µXCT) is capable of producing 3D volumetric information on texture and mineralogy that satisfies some of these criteria. µXCT has been used extensively to study the porosity and internal pore structure of iron ore pellets as part of downstream processing. It has not been widely applied to earlier mineralogical and textural analysis of unprocessed ore, due to the limited ability of X-rays to penetrate high-density samples. In this contribution, we propose scanning methods to overcome this limitation, thereby facilitating a broader application of µXCT to iron ore resource management.CITATION:Bam, L C, Miller, J A, Becker, M, De Beer, F C and Basson, I, 2016. X-ray Computed Tomography – Determination of Rapid Scanning Parameters for Geometallurgical Analysis of Iron Ore, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 209–220 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Garg R. K

Himalayan ranges on the northern border of India are source of many perennial rivers and suitable sites for large dams have been located therein. However, Himalayas are young mountains and comprise of comparatively weaker rocks having adverse geological features like shear seams, thrust zones, minor and major faults and intense jointing. Tehri dam project under construction, is located in lower Himalayas. It envisages construction of a 260.5 m high earth and rock fill dam and an underground power station of 2000 MW (Eight machines of 250 MW each, four of which will be reversible) installed capacity. This dam will be the highest and the underground complex will be the largest to be constructed in India in the Himalayas. The under- ground complex comprises of 25 km of tunnels varying in diameter from 6 m to 11 m and seven large cavities of various sizes, the biggest being 22 m in width, 194 m in length and 65 m in height. Rock formation in the power house complex belong to phyllites having various joint sets spaced from 0.5 m to 3 m. Due to the poor geological conditions and closely spaced net work of large cavities, the planning, analysis and design of the cavities is a challenging job. Many aspects have to be considered in determining the sizes, locations and orientations of the various cavities taking into account the properties and jointing pattern of rock mass, functional requirements and economics. Correct evaluation of loads and forces is necessary for economical design of supporting system for the various cavities. Rock loads on the roof of cavities and their supporting system will be assessed with the help of the latest methods. The stability of the rock mass around the cavity will be evaluated by elasto- plastic method using finite or boundary element techniques. A scheme of field investigations, laboratory tests and instrumentation for deter- mining rock properties in preconstruction stage and for monitoring behaviour of the underground cavities during and after construction is envisaged.

Jan 1, 1987

By C Nucifora, M Landers, J Jones, G Maddocks, K Mandaran, A Forbes, W Wilson, S Newman

Glencore’s Mount Isa Mines Limited (MIM) operates the Mount Isa open cut and underground copper (Cu) and zinc-lead (Zn/Pb) mines near Mount Isa in Queensland, Australia. Tailings from processed Cu and Zn-Pb ore is contained in a 1,315 ha shallow (< 35 m deep) multi-cell valley fill tailings storage facility (TSF). Static geochemical testing conducted by MIM over the life of mine (LoM) verifies that the Cu, and Zn-Pb tailings has a wide range in sulfide content and diverse mineralogy with significant acid neutralising capacity (ANC) in some samples. The tailings are predominantly classified as potentially acid forming (PAF) using static analytical methods. Kinetic leach testing using free draining columns and humidity cell tests simulating tailings placed on the surface of the TSF suggest that the tailings samples are likely to remain non-acid forming (NAF) for 10 to 40 years under aerial exposure, and much longer than this under saturated conditions within the TSF. During this period of weathering, as ANC is depleted, the neutral pH drainage may contain elevated concentrations of some elements including sulfate, manganese and zinc. Only when the ANC is depleted would the tailings then begin to produce acid drainage. CITATION:Mandaran, K, Jones, J, Nucifora, C, Maddocks, G, Landers, M, Forbes, A, Wilson, W and Newman, S, 2018. Mount Isa Mines Rehabilitation Materials Sampling and Analysis program for closure planning, in Proceedings Life-of-Mine 2018, pp 138–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

Queensland Mines Limited operates a small uranium treatment plant at Nabarlek in the Arnhem Land Aboriginal Reserve, some 265 km due east of Darwin. It was the wish of the local Aboriginal people that the ore be treated over an eight year period and that no township be constructed in Arnhem Land. Due to these wish- es it was decided to house employees and their families in Darwin and fly the employees to the minesite for work rosters. A singleman's style camp only was constructed at Nabarlek. To satisfy the Aboriginal people's wishes all recreation time is spent offsite thus lead- ing to a roster system whereby employees spend three distinct periods of 6, 6 and 4 days on- site, broken by recreation periods of 3, 4 and 5 days in Darwin, during each 28 day period. Employees are divided into four opposing rosters, which allows at any given time for approximately half the workforce to be onsite and the other half on rest and recreation leave in Darwin. This method of staffing has generally proved to be most satisfactory although at times problems arise, in terms of both product- ion and social effect not normally encountered when operating within more conventional circum- Stances.

Jan 1, 1984

By Wright S, Jorgensen F. R A

The reaction between lead sulphate and a number of base metal sulphides (galena, sphal- erite, chalcopyrite and synthetic pyrrhotite was studied as a means of desulphurizing lead sulphate containing fumes and residues to levels acceptable as ISF feed. The reactants were mixed with 50% zinc oxide to act as a "basket" to contain the molten products of the reaction and pressed into small briquettes 20 mm in diam. Factors such as temperature, time and the composition of the atmosphere were investigated. Using the PbS/PbS04 system as an example it was shown that the reaction became rapid above 800¦C and that both sulphur dioxide and oxygen in the atmosphere were detrimental to achieving low sulphur in the product. In an inert atmosphere all the sulphides when roasted for 1 h at 1000¦C gave results corresponding to the elimination of more than 95% of the sulphur in the reactants. Leach plant residues were considered for use as the "basket" material. It was shown that the residual sulphide and sulphate components of the residues underwent similar reactions to those experienced by the pure systems.

Jan 1, 1987

By E Mofya, R Kaunda, P Lever

One of the fundamental requirements for being able to optimise blasting is the ability to predict fragmentation. An accurate blast fragmentation model allows a mine to adjust the fragmentation size for different downstream processes (mill processing versus leach, for instance), and to make real time adjustments in blasting parameters to account for changes in rock mass characteristics (hardness, fracture density, fracture orientation, etc). A number of blast fragmentation models have been developed in the past 40 years such as the Kuz-Ram model (Cunningham, 1983). Fragmentation models have a limited usefulness at the present time because:The input parameters are not the most useful for the engineer to determine and data for these parameters are not available throughout the rock mass. Even if the input parameters are known, the models still do not consistently predict the correct fragmentation. This is because the models capture some but not all of the important rock and blast phenomena. The models do not allow for ætuningÆ at a specific mine site. This paper describes studies that are being conducted to improve blast fragmentation models. The Split image processing software is used for these studies (Kemeny, 1994; Kemeny et al, 1999).

Jan 1, 2001

By C Woodall, G Jardine

The Henty Gold Mine, located in Western Tasmania uses innovative solutions to effectively manage a mining operation in an environmentally sensitive setting and has been presented with several environmental awards. Fill is required as part of the mining method to provide passive ground support, minimise rock exposure and ensure maximum recovery of the small but high-grade orebody. The use of the whole portion of leach residue in the backfill reduces the surface tailing disposal requirements. Therefore, High Density Paste Fill (HDPF) has been selected as the most appropriate fill method to meet these objectives. Additional benefits include the minimisation of excess water from fill and the subsequent need for the collection and treatment of water and slimes. There are minimal equipment requirements during placement, thereby optimising mine resources for production. This paper covers the development of a suitable paste fill system to meet the specific needs of the Henty Gold Mine and the successful commissioning of this system for the first time in Australia.

Jan 1, 1998

The safety culture in mining has progressed towards a zero tolerance of injury. This change has required that some historically inherent risks of mining are engineered out or reduced. One of the significant causes of fatality in Western Australia and Worldwide mining is through rock fall, subsidence and inrush. Efforts put into understanding the material properties of the ground we mine and the backfill we place are reflected in improved safety statistics. It is no longer acceptable to not manage these risks and mining, to be sustainable, has to be safe.   Mining historically produced waste products with little consideration of recycling or impact on the surrounding land. The rehabilitation of mining waste products such as mill tailings, heap leach and waste rock is one step towards managing the environmental impact of these waste products. A better step is towards recycling and redepositing these products to produce a more environmentally sustainable mine site.   Gold fields St Ives lease is an active network of new and historic undergrounds and open pits within the Lake Lefroy and Kambalda district. The process of creating voids underground followed by open pits mining through the old voids allows the use of backfilling to control inherent hazards and dilution. Backfill provides opportunity for the disposal and recycling of mining waste materials at the same time as meeting requirements of mine support. Materials available on the St Ives site include spent heap leach, reclaimed tailings and waste mullock. Through recycling and re-depositing these materials to St Ives and neighbouring mines, the reliance on imported material to meet their needs and impact on surrounding land is reduced.   At St Ives, paste fill and barricade design have been reworked to allow backfilling into stopes with water inflows up to six litres per second. This has required a rethink of the drainage and monitoring of water management systems previously used for hydraulic fill and apply them to paste.   The St Ives open pits have developed methods to mine through underground workings and individual stope voids up to 62,000m3. Here backfill is used to reduce the consequence of catastrophic, unexpected failure of the crown and minimise ore lost down voids and dilution through increased blast movement. This paper outlines the less common methods being adopted to use the recycled materials and ways it has been managed to suit the needs of the company.

Jun 1, 2010

The conventional approach to the disposal of fine coal mine tailings, which involves piping the tailings as an aqueous slurry to a storage where they remain in the form of a permanent wet deposit, is becoming unacceptable. This approach is a legacy of a "contain and forget" mentality, which has economic advantages only in the short term. In the longer term, wet tailings deposits occupy large areas of land and present extreme rehabilitation difficulties. Alternative tailings disposal systems, which are sustainable and which facilitate rehabilitation, are required. The possible alternatives include the mechanical dewatering of fine tailings prior to disposal in combination with coarse reject, tailings disposal into spoil pile valleys, and the combined pumping to disposal of tailings and coarse reject. The most appropriate choice of fine tailings disposal strategy will vary from mine site to mine site. The chosen strategy should be optimised to meet increasingly stringent environmental requirements, within the constraints imposed by each mine. The alternative approaches represent significant departures from past practices, and require considerable industry driven research and development before they can be adopted with confidence. All three alternatives involve mixing of the fine tailings and coarse waste streams, aimed at creating a mixture of reasonable engineering properties. Understanding the engineering behaviour of such mixtures is central to the success of these alternative disposal strategies.

Jan 1, 1991