Search Documents

Jan 1, 2004

Ore sorting is a high capacity, low cost method of pre concentrating ores and in some cases of producing a marketable concentrate. In most cases it is applied to run of mine material, immediately after primary crushing and screening in sizes ranging from 10 mm to 150 mm. Recent developments in bulk sorting of friable uranium deposits have resulted in machines capable of handling fine materials with sensing and separation being achieved on a zone by zone basis. Modern ore sorting machines rely on the synchronous operation of four internal subsystems, feed presentation, sensing, data processing and separation. A variety of different sub systems is available which can be combined in various forms to produce sorters capable of handling a wide variety of mineral types. The benefits in using ore sorting cover a wide range of situations and are applicable to both established mines as well as new mining ventures. Reduced operating costs, increased productivity, capital savings, energy and resource conservation and environmental issues are all part of the reason why ore sorting is finding rapid acceptance in today's mining industry. The suitability of different ore types for pre-concentration using anyone of the variety of ore sorting systems can be quickly established using computer based techniques which require only small samples of the materials under investigation.

Jan 1, 1980

For too long we, as an industry, have borne the brunt of irrational claims, poor science and even worse, journalism with regards to our affect on the environment. To some of us, the overwhelming media attention on greenhouse warming, the polluting outputs of mineral processing or unthinkable depletion of natural resources has left us embarrassed and more unfortunately has turned bright young people away from a career in the minerals industry.This paper shows the hypocrisy associated with an element of the green movement and dispels some general myths on mining disseminated by radical environmentalists.The fallacy of the greenhouse warming effect will be scrutinised by common sense and the mining industryÆs use of land will be discussed and put in proper perspective.Problems associated with safety and emissions and the means to overcome such are discussed briefly.

Jan 1, 2004

By T Christie

Tertiary volcanic rocks make up a significant proportion of the surficial cover rocks of New Zealand, especially in the Taupo Volcanic Zone. Industrial minerals that are associated with or derived from the volcanic rocks include: amorphous silica, allophane, bentonite, diatomite, ignimbrite building stone, illite clays, halloysite clay, obsidian, perlite, pumice, sulphur, titanomagnetite ironsand and zeolite. Of these: bentonite, ignimbrite building stone, perlite, pumice and titanomagnetite ironsand have been mined and processed for 20 to 30 years, but many of the others require further characterisation of the resource and/or development of markets.   We have compiled interim mineral deposit models for halloysite clays in rhyolite and for zeolites in altered vitric tuffs. These models include geological and mineralogical attributes, which are linked to the underlying volcanic and geothermal processes that have produced the minerals and their source volcanic rocks. Halloysite clay deposits at Matauri Bay (Northland) have formed from hydrothermal alteration and weathering of rhyolite. Clinoptilolite + mordenite zeolite deposits in the Ngakuru area (Rotorua district) have formed from hydrothermal alteration of volcanic glass in lacustrine sediments and ignimbrite. Further refinement and application of these models will result in a better understanding of the mineralogy, localisation and origin of the deposits, with consequent applications in exploration and resource assessments.

Jan 1, 2001

By Bishop D. J

The Imperial Smelting Process for the simultaneous production of zinc and lead is probably regarded by the ecologist as a necessary evil with the benefits of its products marginally outweighing the adverse effects of its operation. The purpose of the paper is to examine the environmental impact of the process and to provide information which will demonstrate that the process has considerable indirect environmental benefits and that success is being achieved in reducing direct pollution of the environment by the process. About 12 per cent of the world's zinc and seven per cent of its lead is produced by the process. This proportion will increase with the construction of a new smelter in China. After a brief description of the process the paper considers one of its principal advantages, its ability to treat bulk concentrates. The production of these at the mine can have a number of environmental benefits. Less comminution may be required to separate the metals from the gangue than is needed to separate them from each other; recoveries can be improved in flotation resulting in cleaner tailings dams, less power demand and reduced consumption of potentially hazardous reagents. Simplification of mining and above ground ore handling may also give significant benefits . The process is a considerable consumer of secondary materials such as galvanisers' ashes, copper smelter dusts and materials containing zinc and lead derived from steel plant dusts. The majority of these materials are fed to the blast furnace after hot briquetting. The consumption of secondary materials is a considerable environmental benefit since otherwise they would require to be dumped in secure land-fill sites. The operation of the process itself continues to be subjected to increasingly stringent environmental standards of which examples are provided. Details are provided of lead emissions at Avonmouth showing considerable success in reducing these while increasing production. The slag from the process continues to find many useful applications.

Jan 1, 1993

Open pit mining has considerable damaging effects on the environment of the mining region. These harmful influences have to be controlled during mining operation until mine closure. Different sections of mined land, such as; pit(s), waste dump(s), tailing pond(s), roads, areas for onsite facilities and free land zones which are not mined, have to be reclaimed through treatment of environmental pollution and implementation of a permanent post mining land use (PMLU) after mine closure. Implementation of a permanent optimal post mining land use (OPMLU) is one the most decisive criterion which effects on reclamation procedure, mine closure and their costs. Therefore to define ultimate pit limit (UPL), mine closure and reclamation costs should be entered in the calculation iterations same as the other variable costs of the projects. Estimation of closure and reclamation costs of a mining project is carried out based on the attained OPMLU and the specifications of the mine site. In this paper, a model is developed to provide OPMLU for pit area through fuzzy multi-attribute decision making (FMADM) technique. The model was implemented on a hypothetical copper mine in northwest of Iran as a case study. Lumber production was selected as OPMLU for the pit area. It is finally concluded that through the developed model, OPMLU for different sections of mined land in an open pit mine project is defined. Also closure and reclamation costs are estimated based on the defined OPMLU to achieve a more accurate UPL.

Dec 6, 2010

The sequences in alteration and mineralisation from five copper-gold porphyry systems (Taysan and Didipio, Philippines; Horse-Ivaal and Wafi River, PNG; and Goonumbla, Australia) and one gold-copper skarn system (Browns Creek, Australia) are documented in this paper. Alteration and mineralisation in all these systems reflect a common evolution from crystallisation of melts emplaced at shallow crustal levels (zoned potassic -> propylitic alteration), followed by exsolution of volatile-rich fluids from these melts (porphyry quartz ¦K-feldspar/biotite veins and local high temperature advanced argillic alteration), to a progressive cooling of the intrusion which results in associated retrograde alteration. Copper-gold mineralisation in all cases is almost exclusively restricted to the cooler retrograde events. The recognition of the temporal and spatial zonations in alteration and mineralisation in gold-copper porphyry systems has significant relevance in the interpretation of geophysical signatures, overprinting alteration, vein sequences and structural controls, and can lead to more focused and potentially more cost-effective exploration.

Jan 1, 1999

Geostatistical methods have become well established in the last two decades for the evaluation of ore reserves in base metal, industrial minerals, coal and gold deposits of the Witwatersrand type. However, there has been considerable debate about the applicability of geostatistical techniques when applied to vein-type gold deposits with hydro or epithermal mineralisation. The main problems stem from a lack of spatial continuity and the highly erratic sample values that characterise these deposits. This paper reviews some of the current geostatistical techniques that are applied to the evaluation of gold prospects.

Jan 1, 1992

By V Poizat

In different parts of the world the term epithermal is commonly used for a variety of deposit styles. Using the redox state of the ore-forming fluid (inferred from mineralogy and alteration), the metal assemblage of deposits, and other characteristics, at least five different styles of epithermal deposit can be distinguished. Most of these different deposit styles appear to be related to magmatic fluids, with differences resulting from different compositions of source magmas. The most common style of epithermal deposit (low-sulfidation gold-silver deposits associated with calc-alkaline volcanic rocks) remains the most difficult to explain; the metals in these deposits may be derived by basement leaching without magmatic input, or they may come from magmatic volatiles, with contaminated I-type or S-type magmas as the most likely source.

Jan 1, 1995

Australia has a long history of underground mining. Even withadvances in open cut mining equipment, techniques andeconomics, many orebodies are still best mined by undergroundmeans. In addition, modern exploration tools are æuncoveringÆorebodies that are at increasing depths. South African mines arecurrently producing from below 3 km, and developing down to5 km depths û it is likely that Australian mines will also becomemuch deeper over the next 20 years. One of the most significanttechnical challenges in deep mines is the problem of heat.Community expectations and legislated standards continue todrive operations towards improving the working conditions inmines. The hazards and costs associated with chronic hotworking conditions (heat illness, poor safety, poor productivity,higher operating costs and poor morale) are also becomingincreasingly recognised (Brake, Donoghue and Bates, 1998). Theexposure of miners to many other occupational hazards has beenreduced over the past 50 years. However, despite air-conditionedcabins greatly reducing the heat stress on mobile plant operators,there are still many Australian mine workers subject to levels ofthermal stress that existed a century ago. There are severalreasons for this, including a frequently-poor understanding of thephysiology of working in heat by mine management, no agreedmining code of practice for working in heat, the lack of a robust,practical-sized instrument to measure heat stress, the costpressures on the industry and, to some extent, deep-seatedtraditional management and worker practices. Howeversignificant progress has been made in many of these areas (Brakeand Bates, in press), with the net result that there is likely to be a trend towards installation of refrigeration of some form in manyAustralian mines in the future. This will add directly to the costof operation, but will also have direct and indirect benefits,including cost benefits. It should also be noted that Australia isnot at the forefront of adopting practices to manage temperaturesin the workplace: South African metal mines usually haverefrigerated cooling, and Canadian mines spend large sums onheating, with heating costs (averaged over a full year) of up to$A1 per tonne mined (Bandopadhyay et al, 1997). The history of mine refrigeration dates back to 1919 when thefirst plant was installed at Morro Velho, Brazil. By 1965, the totalinstalled capacity (worldwide) reached about 100 MW(R)i. Since 1965 the growth in mine refrigeration capacity has beenexponential, with a doubling every six or seven years (Howes andNixon, 1997). South Africa is by far the largest user of minerefrigeration, with over 300 refrigeration machines installed. This paper discusses the key design issues associated with theapplication of refrigeration in underground metal or coal mines.Whilst the emphasis is on large, surface plants, small, surface orunderground refrigeration plants can also be very effective in thecorrect application and many of the principles of design andoperation are the same.

Jan 1, 2001

By J G. Webster-Brown

The Tui Mine is located near Te Aroha at the base of the Coromandel Peninsula. It was a lead-zinc mine, which closed in 1973 due to declining concentrate prices, high overheads, and high mercury levels in the ore. The site was abandoned, leaving behind an acid rock drainage generating system, including a sulfide-rich tailings dam which has since caused pollution of Tui Stream, as well as open adits and waste piles which drain predominantly into the neighbouring Tunakohoia Stream. At the AusIMM conference in 2003, Harvey and Webster-Brown presented water quality results from the Tui mine site and lower stream catchments in 2002. In April 2006, Environment Waikato undertook remediation works to stabilise the dam and reduce acid drainage entering Tui Stream. In this study, water quality results from the Tui mine site and lower stream catchments are again being determined, in order to compare with the pre-remediation results. Preliminary data collected for summer indicate a minor but consistent improvement in water quality in the lower stream catchments, although lower Tui Stream continues to exceed ANZECC (2000) aquatic life guidelines for Cd, Cu, Pb and Zn. This slight improvement may be due to a decrease in the flow of ARD into Tui Stream, as there does not appear to have been an improvement in quality of the contributing ARD waters.

Jan 1, 2007

By R Hall

Subduction zone magmatism is a direct response to tectonic and chemical processes operating at convergent margins. Changes in the tectonic configuration of plate boundaries in SE Asia during the Cenozoic had consequences for the nature and volume of magma produced. Retreat or advance of the trench hinge has probably been an important process in controlling the presence or absence of magmatism in SE Asian subduction zones. This process also provides a means of replenishing the mantle wedge and counteracting the effects of melt extraction in depleting the wedge. Changes in the nature of recycled material and lithologies of the over-riding plate also have the potential to influence the lavas that are erupted in arcs. Several locations in SE Asia have experienced magmatism bearing the geochemical signature of subduction but are remote from coeval subduction zones. Such magmatism requires an earlier period of mantle enrichment by subduction but may result from localised extension. The distribution of such magmatism may provide information of tectonic value. Some adakitic magmatism occurred in tectonic settings where there is no evidence for subduction of young oceanic crust at the time of magma genesis. Slab melting in such settings is not possible and alternative mechanisms are required to explain the occurrence of, at least some, adakitic lavas.

Jan 1, 1999

By Y X. Xue, J Pan, D Q. Zhu

In order to reveal the correlation between the fundamental sintering characteristics of iron ores and their real sintering behaviours, a comprehensive evaluation index is proposed based on the measurement of four high temperature indexes, ie assimilation temperature, liquid phase bonding strength, liquid fluidity and calcium ferrite formation percentage, and the sintering pot tests of single ore fines and their blends. The results show that both the lowest assimilation temperature and liquid fluidity of ore blends appear to be the linear superposition of those of single iron ores except for the liquid phase bonding strength and calcium ferrite formation percentage. Furthermore, the tumble index of the sinter product obtained from blended iron ores also corresponds to a linear superposition of that of single ores, but not for the solid fuel rate and productivity. The comprehensive strength index YT exhibits a credible linear positive correlation with the four high temperature reactivity indexes, whereas the comprehensive productivity index YP possesses a lower correlation with the four high temperature reactivity indexes. The comprehensive strength index YT developed can predict the tumble index of the sinter product quite well, but the comprehensive productivity index YP cannot be used to evaluate the productivity effectively.CITATION:Zhu, D Q, Xue, Y X, Pan, J and Shi, B J, 2017. Correlation between high temperature sintering characteristics and sintering behaviours of iron ore fines, in Proceedings Iron Ore 2017, pp 123–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By V L. Los, G J. Abramson

The paper examines three types of polar zoning of ore-forming and associated elements that can be detected from geochemical data. Polar zoning is mapped in the form of geochemical ore systems of various ranks. Various types of polar zoning can be found in some systems, which present a general geochemical model of the ore object. The genetic basis of zoning is examined from the perspective of the conception of geoelectrochemical redistribution of matter, including ore-forming elements. The volume of the geochemical ore system may be used in the prognosis of resources for every rank.

Jan 1, 1999

By P F. Lauricella, D Hendri

In the Mesel sediment-hosted disseminated gold deposit, the spatial distribution of hydrothermal alteration is controlled by steeply dipping faults and shallowly dipping lithologies. Hydrothermal alteration of carbonate rock is characterised by decalcification, dolomitisation and silicification. Intense argillic alteration occurs in a laccolithic andesite intrusion adjacent to decalcified and silicified carbonate units. Sulphide minerals (pyrite, realgar, orpiment, stibnite and cinnabar) accompany hydrothermal alteration and precious metal mineralisation. The trace elements Ag, As, Sb and Hg are zoned spatially throughout the deposit. Mesel contains a mineable gold reserve of 7.8 million tonnes at 7.3 g/t Au. Gold mineralisation is preferentially localised in carbonate rocks adjacent to and beneath the andesite intrusion. The ore body consists of a central, near-vertical, high grade 'feeder' system flanked by tabular, inward dipping, moderate grade 'ouflow' zones. Mineralisation is controlled predominantly by two steeply dipping faults with high grade (=10 g/t) gold zones centred about structural intersections and fault splays. Gold is submicron size and locked in very fine grained (<10 microns), disseminated and fracture-controlled arsenical pyrite. The Mesel deposit developed where high angle faults guided ascending, sulphidising fluids into reactive carbonate stratigraphy adjacent to and beneath the andesite intrusion and during subsequent migration of the auriferous fluids along 'outflow' channels. Early decalcification and dolomitisation enhanced porosity and permeability prior to silicification and sulphidation. Gold deposition occurred late in the genesis of the deposit.

Jan 1, 1995

By J J. J Chen, J C. Zhao

A water/air model was developed to simulate the refining of molten aluminium by the sparging of gas through an impeller. The optimal gas dispersion depends upon selecting the correct gas rate for a given impeller rotational velocity to prevent flooding or channelling. Correlations illustrating this flooding behaviour exist for standard impellers within standard tank geometries. However the validity of these correlations has not been substantiated for gas dispersion in high temperature molten metals with non-standard tank and impeller dimensions. Metal refining is most efficient when fine bubbles are generated and uniformly distributed within the treatment tank. The application of some measuring technique able to detect this distribution within a non transparent operating treatment tank would be invaluable, enabling the optimisation of gas flow and impeller speed.   A technique has been developed to measure the pressure fluctuation levels at specific points in the water model. Comparison of these pressure fluctuation data with photographic evidence obtained in the water model suggests that the flow regime in the metal treatment unit may be determined using this technique.

Jan 1, 1995

By S B. Stewart, C J. Restarick

Over a four-hour period of steady plant operation samples were taken at regular intervals frum points within the grinding and flotation circuits. Size fractions of each composite sample were analysed for lead and zinc values and a comparison made of the behaviour of the lead, zinc and gangue minerals, size by size throughout the whole circuit. Analysis of the breakage behaviour using dynamic mathematical models gave the rates of breakage of each size fraction of each main component. Simulated grinding experiments shaved that the main grinding circuit had some reserve capacity. In the lead flotation circuit all lead values between 150 mesh (Tyler) and 5 ¦m had excellent flotation characteristics, and a major proportion had a high rate of flotation which was practically the same for all sizes. Increase in overall lead recovery would require improvement of the flotation behaviour of ultra-fine lead minerals. These were slav floating and were responsible for approximately half the lead losses in the final zinc concentrate and one thiro of the lead losses in the final tails. All sizes of zinc values between 150 mesh and 7 ¦m floated well and the performance of the zinc flotation circuit was mainly limited by the relatively poor flotation of the very fine zinc values. Approximately 60 per cent of the zinc lost to the final tails lay within the -7 ¦m fraction. The overall flotation conditions were conducive to very good selective flotation of the major proportion of the values and limitations in metallurgical performance were mainly due to the properties of the ultra-fines.

Jan 1, 1971

According to the data provided by the most recent European Survey on Working Conditions, roughly 25 per cent of the European working population is exposed to mechanical vibrations for no less than one quarter of the work shift duration, while around ten per cent are exposed for the entire work shift. The occupational exposure to whole-body vibration (WBV), in particular, represents a major health risk in mining, quarrying and civil excavation activities. In accordance with European Directive 2002/44/EC, the latest version of the Italian law on physical risks has recently confirmed the possibility of using relevant literature data on vibration magnitude in order to evaluate personal occupational exposure (vibration database or data provided by the manufacturer). Still the alternative option, based on field measurements, represents the most appropriated method of risk assessment, as it accounts for the actual operating condition at the workplace; actual operator and vehicle under investigation and specific working cycle. The article discusses the vibration measurements taken on a number of heavy machinery (excavators, loaders, trucks, dumpers, etc) employed for talc extraction in a mine located in Sardinia and the resulting personal exposure for the drivers. The assessment was carried out in accordance with the specifications of ISO 2631-1 and EN 14253.

Dec 6, 2010

By S Hanke, J Burden, P Spies

The Waterview Connection will complete Auckland’s long-planned Western Ring Route, a 48 km north-south motorway alternative to State Highway 1 that bypasses the central city to the west. The project involves construction of 5 km of new motorway – half of it underground in tunnels – to connect the Southwestern (State Highway 20) and Northwestern (State Highway 16) motorways.The Western Ring Route will link the major population and industrial centres of Manukau, Auckland and North Shore to give the region the connected and resilient strategic road transport system it needs to underpin economic growth and sustainable development. It will also provide a direct motorway link between Auckland’s central business district (CBD) and international airport.The project involves construction of twin 2.4 km driven tunnels with an outside diameter of 14.41 m beneath residential suburbs, a major arterial road and a rail corridor. Enabling works began in January 2012 while tunnel construction using an earth pressure balance (EPB) tunnel boring machine (TBM) began in November 2013.This presentation introduces the Waterview Connection project, its role in the development of the Auckland motorway network, its procurement process, the alliance delivery model and an overview of the project’s design features and construction progress to date.Design and construction highlights of the presentation include the TBM start-up, turnaround and breakthrough arrangements as well as the experience gained during the first tunnelling drive. The presentation also covers an innovative process developed for invert construction behind the TBM that is independent of tunnel excavation.CITATION:Spies, P, Burden, J and Hanke, S, 2014. The Waterview Connection Project – progress to date, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 519–540 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

The Barmac autogenous crushing mill is one of the most successful new comminution technologies to become available to the mining and industrial minerals industries in this decade.   The Barmac autogenous crushing mill is an innovative Vertical Shaft Impactor which operates in essence like a high intensity dry ore centrifugal pump with the reduction occurring primarily as a result of high velocity rock to rock impact in a fully rock lined crushing chamber.   With applications in a wide range of mining and industrial minerals operations the Barmac autogenous crushing mill presents an opportunity to enhance reduction and liberation whilst providing many cost savings and production increases in new and existing plants.   This paper briefly describes the operation of the Barmac autogenous crushing mill and reviews its benefits.

Jan 1, 1990