Search Documents

By W. D. Donnelly, M. L. Rudee

THE crystallography and morphology of ?-Al3Fe precipitates in an A1 + 0.5 wt pct Fe alloy have been studied by transmission electron microscopy. The alloy was cast in cylindrical ingots, 15 cm in diameter and 60 cm in length, and cooled slowly. The measured composition was 0.527 wt pct Fe, 0.001 wt pct Mg, and 0.003 wt pct Cu. Spectrographic analysis revealed no additional trace impurities. Thin slices were cut from the ingot and reduced by more than 95 pct by rolling to a thickness of 0.1 mm with no intermediate annealing treatments. These thin sheets were then vacuum-annealed for 1 hr at 612°C and air-cooled in their capsules. Thin foils for examination in the electron microscope were prepared by electropolishing. The precipitate is found in the form of oval platelets on the (110) planes of the matrix. The major axes of the platelets are parallel to the (110) directions of the matrix, and vary in length from 1/2 to 2 p. The thickness is about 1/10 µ. Examples of platelets, both in the plane of the foil and normal to the foil, are shown in Figs. l(a) and l(b), respectively. lack' found that ?-A13Fe (more correctly Al13Fe4) belongs to the monoclinic system. Using Black's structural data and simultaneous electron-diffraction patterns from the matrix and precipitates, the habit planes and directions were determined to be: (001)? 1 (110)Al [100]?|| H [001]Al The orthogonal crystallographic axes of the precipitates are accurately in the habit plane, while the measured coincidences of the directions are only within 10 deg. The major axis of the platelet is parallel to [010] in the 0. This orientation corresponds to the direction of nearest registry of the lattices.

Jan 1, 1964

By G. R. Leverant, M. Gell

The high- and low-cycle fatigue poperties of MAR-M200 directionally -solidified into columnar-grained and single crystal forms were determined at 1400" and 1700°F. These results were compared with the corresponding properties of conventionally -cast MAR-M200. The low-cycle fatigue lives of the columnar-grained and single crystal materials were similar at both temperatures and were one to two orders of magnitude greater than those of conventionally-cast material. The variations in the fatigue lives among the three forms of MAR-M200 were related to the more rapid rate of intergranular muck propagation compared to that of transgranular propagation. In conventionally-cast MAR-M200, cracks were initiated in grain boundaries and crack popagation occurred rapidly along an almost continuous grain boundary path. In the columnar-grained material, crack initiation occurred on short transverse segments of grain boundaries, but crack propagation was transgranular. The fatigue lives of columnar-grained and single crystal materials were approximately the same because most of the life in both materials was spent in trans-granular propagation. For the directionally -solidified materials, the number of cycles to failure, Nf, can be related to the total strain range, , by: heT = K where n and K are 0.16 and 0.044 at 1400'F and 0.29and 0.098 at 1700, respectively. In addition to intergranular crack initiation in the columnar-grained material, initiation also occurred at we-cracked MC carbides and micropores in both directionally-solidified materials. At 1400°F, fatigue life was reduced with increasing MC carbide size, but at 1700 there was no effect of carbide size. THE creep and stress-rupture properties of conventionally-cast nickel-base superalloys can be greatly improved by directional solidification into either single crystal or columnar-grained forms. The improvement in properties results from a reduction in intergranular cavitation and crack growth in the columnar-grained materials and the complete absence of this fracture mode in the single crystals. This paper describes the effect of grain boundaries on the elevated temperature fatigue properties of the nickel-base superalloy MAR-M200. The effect of cycling frequency on cracking arid fatigue life and the role of MC carbides and micropores on crack initiation are also emphasized. The fatigue properties of columnar-grained and single crystal MAR-M200 at room tem- perature,4,5 and the change in the mode of fatigue crack propagation with temperature6 have recently been described. I) EXPERIMENTAL PROCEDURE The material used in this study was the nickel-base superalloy MAR-M200, directionally-solidified into columnar-grained and single crystal forms. The columnar grains were approximately 0.5 mm in diam. The nominal composition of these materials in wt pct was 0.15C, 9Cr, 12.5W, loco, 5A1. 2Ti, lCb, 0.05Zr. 0.015B, bal Ni. They were solutionized for 1 to 4 hr at 2250°F followed by aging at 1600°F for 32 hr. which resulted in 0.2 pct offset yield stresses of 150,000? 144,000, and 95,000 psi at room temperature? 1400°, and 1700°F, respectively. The corresponding elastic moduli parallel to the testing direction were 19.2. 15.0, and 12.5 x 106 psi, respectively. Specimen design, testing procedures and alloy mi-crostructure have been described previously and will only be summarized here. Following the 1600°F aging treatment. MAR-M200 contains an ordered, cuboidal, y' precipitate 0.3 1 on edge, which is coherent with the 1 matrix. The y' precipitate is quite stable; even after testing at 1700°F. the precipitate is only slightly enlarged and its corners somewhat rounded. The alloy also contains a small volume fraction of micropores, and MC carbides. some of which contain preexisting cracks5 formed during casting. These cracks are always parallel to the long dimension of the carbide. Measurement of MC carbide size has been described previously.5 Axial fatigue tests were conducted in air over a wide range of strain amplitudes in both the high - and low-cycle fatigue regions, with specimen lives varying from about 10' to 10' cycles. Low-cycle fatigue (LCF) tests were strain-controlled with strain varied between zero and a maximum tensile value at a frequency of about 2 cpm. High-cycle fatigue (HCF) tests were stress-controlled with the stress varied between 5000 psi and a maximum tensile value less than the yield stress at a frequency of either 10 cps or 0.033 cps (2 cpm). The temperature in the gage section was controlled to 52°F. Specimen axes were within 5 deg of the [001] growth axis of the single crystals and the common [001 ] growth axis of the columnar-grained material. Specimen gage sections were electro polished prior to testing. After the standard heat treatment, three specimens were coated with a typical aluminide coating applied as a slurry. An additional specimen was given the coating heat treatment without actually being coated. In all cases: specimens were reaged at 1600°F for 32 hr after receiving the coating heat treatment at 1975'F for 4 hr.

Jan 1, 1970

By C. E. Birchenall, H. M. Schadel

THE purpose of this study was to measure the vapor pressure of silver as the first step in the determination of activities in silver alloys and to test the limitations of the method adopted. In order to work at low pressures, below 2x10-2 mm of mercury, the orifice effusion technique was employed. To shorten the time of collection of silver from the atomic beam, radioactive silver (Ag110) was used as a tracer. The rate of effusion of a monatomic vapor from an "ideal" orifice, where the thickness of the orifice edge is negligible compared with the orifice diameter, can be readily calculated from the kinetic theory of gases, G = vM a p/v2pRT where G is the weight of material effusing from the orifice per unit time; p is the vapor pressure at oven temperature, T; R is the gas constant; M is the molecular weight of the vapor; and a is the orifice area. Consolidating constants and expressing as the weight of material effusing from the orifice in a period of time, t, (5.83)(10-2) (vM) (a) (t) (p)/vT where GT is total weight of monatomic vapor effused (g); M is molecular weight of the effusing tracer vapor; a is orifice area (cm2); t is time of effusion (sec); p is vapor pressure of effusing material (mm of Hg); and T is oven temperature (OK). The vapor effuses from the orifice in a hemispherical pattern, and the intensity of the beam in any direction is given by the cosine distribution law.' Considering this, the weight of effused material can be calculated from the amount of material passing through a circular collimator intersecting the beam. If such a collimator is in a plane parallel to the plane of the orifice and with center on the normal to the orifice center, GT = G?/1-cos2? = G?/sin2? where G? is the weight of effused material passing through the collimator, and 0 is one half the apex angle of the cone defined by the collimator circumference and the orifice center. Reducing eq 3 to the more directly measurable quantities of orifice to collimator distance, d, and collimator diameter, D, the expression becomes,

Jan 1, 1951

ALABAMA Aldrich -Thomas, D A Altoona -Cain, J Anniston -Cowie, L K Walmsley, W N White, H E Ashland -Sturdevant, J C Bankhead -Connaway, M B Bessemer-Ball, E M McKenzie, W C, Jr Mitchell, F R Morgan, C Thompson, N E Birmingham -Abbott, C E Adams, J H

Jan 1, 1923

By Rodney P. Smith

THE solubility of columbium nitride in ? iron has been determined for the temperature range 1191o to 1336°C from the nitrogen content and metallogra-phic examination of a series of Fe-Nb alloys.* (0.0 to 0.92 pct Nb) equilibrated with a purified gas mixture of 1 pct hydrogen in nitrogen. The method is the same as that used by Darken, Smith, and Filer' to determine the solubility of aluminum nitride in y iron. The variation in the furnace temperature during an equilibration period was about ± 2.0°C. Each sample was approximately 1/2 in. wide, 2 in. long, and 1/16 in. thick. A time series at 1200°C using samples of highest columbium content indicated that one day was sufficient for equilibrium; however, to be on the safe side all samples were left in the furnace for either two or three days. Afterequilibration, the samples were brought to room temperature by quenching in water. The experimental results are shown in Fig. 1. To be in accord with the values reported by Wriedt and Gonzalez2 and the temperature coefficient of our results at higher temperatures, the nitrogen content of iron at 1191oC is assumed to be slightly lower than our experimental value. Our data for the single-phase regions are not sufficiently accurate to establish an interaction coefficient for nitrogen in these alloys. However, the change in nitrogen content with change in alloy content for a number of systems (Fe-N-A1;3,1 Fe-N-Ni;372 Fe-N-Si.3949 Fe-N-V;3,5 Fe-N-Cr;3,6 Fe-N-Mo3,7) has practically the same value for the liquid alloy at a temperature near 1600°C as for the solid alloy at temperatures near 1200oC when the alloy content is below a few percent. On this basis the lines through the single-phase regions have been drawn with a slope corresponding to an increase in nitrogen of 0.0013 pct per 0.1 pct Nb.3 The straight lines through the two-phase regions were drawn with a slope corresponding to a one-to-one atom ratio of nitrogen to columbium in the nitride. The X-ray

Jan 1, 1962

By Frank R. Corwin, Selden S. Rodgers

PAGE I. Introduction,........... 383 11. Brief History of Present MacDoUgall Plant,.... 384 III. First Experimental Work on Increasing Capacity of Furnaces, 385 IV. Effect On MacDouRall Plant of IncreaBed Draft from New Smelter Stack,,.......... V. Increasing the Capacity of the MacDouGall FurnaceS,.. 391 (A). Test of Arthur Crowfoot on Increasing Capacity,.... (a). Description of Test,........ (6). Discussion of Results Obtained from Test,... 393 (B). Investigation Carried Out by John A. Church, Jr.,... 395 (a). Advantages of High Speed,......398 (C). Effect on Regular Operation of Department by Applying Results Obtained from Experimental Work ..... 399 (D). Fundamental Principles Involved in Increasing the Tonnage, . 400 VI. Treatment of an INcreased Amount of Ore Screenings,.. 401 VII. Maximum Percentage oF Ore Screenings in a MacDoUGall Feed, 403 VIII. Tests to Further Increase Capacity of Furnaces,... 406 IX. Tests to Decrease PercentaGe of Flue Dust made by MacDouGall Furnaces,............. (A). Repath-Marcy Furnace......... 408 (B). Modified Hepath-Marcy Furnace,....... (C). Crouse Furnace Designed for Dust Prevention,.... 413 (a). Tests on Crouse Furnace,....... X. Concrete Hearths,.......... 419 XI. Conclusion,............ I. Introduction. Since the first installation of MacDougall roasters at the Great Falls smelter of the Anaconda Copper Mining Co., the capacity of the furnaces.has been more than doubled. During the first nine or ten years of the operation of the MacDougall department the tonnage treated by the furnaces remained practically unchanged. Experimental work carried out in 1906, however, showed that increasing the draft of the furnaces would bring about an increase in capacity. In 1909 the MacDougall department was connected to the new smelter stack and

Jan 1, 1914

By R. G. Weavind, R. S. Young, I. Wolf

ONE of the most important fields of investigation at the Diamond Research Laboratory in Johannesburg is concerned with improvements in metallurgical practices for the diamond mining companies, with particular reference to increased recoveries of the smaller industrial stones. Considerable work has been done on the possible application of flotation processes to the diamond industry. From the viewpoint of recovery processes, diamonds in their natural state may be grouped into two classes, the water-repellent diamonds, which adhere to a grease surface, and the water-avid diamonds, which, because of their wettability, will not adhere to a grease surface and must be recovered by means other than the grease tables used for water-repellent diamonds. Experiments in the flotation of small diamonds from both kimberlite and alluvial deposits indicate the following conclusions: Water-repellent diamonds: Satisfactory flotation of —16 mesh diamonds, which are naturally water-repellent, may be accomplished using either Aero-float 25 together with cresylic acid, or Du Pont B23 as frother together with kerosine as auxiliary oily conditioner or froth stiffener. The quantities of reagents required are of the order of 0.15 lb per ton Aerofloat and 0.18 lb per ton cresylic acid. The use of acid circuits is detrimental, and for best results a pH between 7 and 9 should be maintained. R. G. WEAVIND and I. WOLF are with the Diamond Research Laboratory, Johannesburg, South Africa, and R. S. YOUNG, Member AIME, is Director of Research, Diamond Research Laboratory. TN 76B. Manuscript, March 23, 1951. A flotation period of 5 to 10 min is necessary to insure that all floatable diamonds are removed. Diamonds larger than 16 mesh cannot be recovered satisfactorily by flotation. Xanthates do not act as collectors for diamonds, and this is probably associated with their inability to impart a water-repellent surface to this mineral. Water-repellent diamonds smaller than 28 mesh can be floated quite well by the addition of a frother alone, such as pine oil or Du Pont B23. Water-avid diamonds: Partial flotation of the smaller sizes of wettable diamonds can be achieved by preconditioning with fatty acid soaps, cationic amines, and similar reagents, which will impart a water-repellent film to diamonds. Washing to remove excess reagent, followed by flotation, will result in a fair recovery, but the latter is much lower than for water-repellent diamonds. Crushed boart: Recovery of crushed boart from the waste products of industrial uses is best accomplished by first conditioning the diamonds present in the mixture with fatty acids, cationic amines, etc., removing the conditioning agent by washing, and floating in a cell of the pneumatic type. Flotation reagents found to be most suitable are Du Pont B23, and Aerofloat 25 together with cresylic acid. The optimum quantities are 1.2 g Du Pont B23, and 0.55 g Aerofloat plus 1.4 g cresylic acid, per liter of pulp in the cell. A solids-to-water ratio of 1 to 4 is found to be the most suitable, and alkaline circuits are necessary for best results. Diamonds larger than 28 mesh are not recovered satisfactorily by this procedure, but for finer sizes flotation offers an excellent procedure for the reclamation of this strategic industrial material.

Jan 1, 1952

By R. G. Treuting, W. C. Ellis

The twinned state is characterized by a lattice of coincidence sites. Imperfections are required at stable lateral twin interfaces. Twinned regions can occur with relative ease in the diamond cubic IN recent contributions1,2 on the origin and growth of cubic annealing twins, attention has been directed to the orientation relations between such twinned components and their parent matrix. There are some aspects of twinning which may be illuminated by a more detailed consideration of the twinned state" alone. As an extreme example, the dense twinning in cast ingots of germanium,&apos; as contrasted with the rarity of twins in cast face-centered cubic metals, is yet to be accounted for. It has been this that has led us to the present work, which, it will be noted, uses methods and constructions in many respects similar to those of Kronberg and Wilson.&apos; In the cubic systems, a 70" 32&apos; rotation about a <110> axis is angularly equivalent, as to twinning, to the more usually considered 180" rotation about a <111> axis. Figs. 1 and 2 show a (110) projection of a twinned face-centered cubic lattice and a twinned diamond cubic lattice. In both figures, the two adjacent planes A and B, shown by the larger and smaller circles, are sufficient to represent the entire array. In each case a section of lattice, the original atom sites of which are shown by open circles, has been rotated as indicated through 70" 32&apos; to bring an original. [112] direction into coincidence with the [112] diiection. The latter is the intercept on the (110) projection of the (ill) plane normal thereto, the twinning plane. In the face-centered cubic case the rotation can be performed about an axis passing through an atom-site; the mirror plane then is also a composition plane containing atoms common to both twinned and untwinned lattices. The diamond cubic lattice may be construed as two interpenetrated face-centered lattices. Its (111) planes recur in a sequence of alternately short and long interspacings. Consequently a mirror plane for twinning cannot be a composition plane, but must be the bisector of one of the spacings. When the longer spacing is selected, the closest distance of approach across the mirror plane in the [ill] direc- tion is identical with that in the untwinned structure. In each case periodically recurring (ill) planes (parallel with the twinning plane) are found, on which there is coincidence of atom sites of the pre-twinned and twinned orientations; these are indicated by the cross-hatched circles. In the face-centered lattice there is such coincidence every third (ill) plane; in the diamond cubic lattice, on two adjacent planes in every six. At the twinning interface in the latter, there is on each side of the mirror plane a (ill) plane of atoms common to both twin components. Conceivably, there is little influence on a plane of atoms about to be adhered to such a pair of coincidence planes, whether it be laid down in a normal or in a twinned position with respect to the previously formed structure. Slawson% as attributed the high incidence of twinning in diamond to this boundary state. Further examination shows that the motion of intermediate planes can consist of various pairs of equal and opposite translations, for example of (ill) planes in the [l&apos;;i2) direction, the familiar twinning shear, indicated in the small schematics in the figures. Since the translations form a system of shears of alternating sign between coincidence planes, twinning could take place by such a mechanism over an extended region without extensive shear; in fact, in this case any atom moves but the distance in the [1i2] direction. One alternative construction for the face-centered cubic lattice leading to the same end result is illustrated in Fig. 3. The plane (711) with respect to the pretwinning orientation (the twinning plane of Fig. 1) is given, the twinned region arbitrarily bounded by <110> and <112> directions. The coupled shear is identical to that of Fig. 1. The "rotational" movement about coincidence sites generating the same twinned position could consist as shown of the translation a,/d% for each atom of a group of three in the B layer in a different one of the three <112> directions, and a similar translation of the underlying three atoms in the C layer in either the same or the opposite sense. This is not dissimilar to Kronberg and Wilson&apos;s construction for their 22" rotation of three adjacent (111) planes.

Jan 1, 1952

AARONS, J. BOYD, Major. AGNEW, FRANK VANS. ALLEN, HERMAN H., Private, D Co., 8th Reserve -Engineers. AMBLER, HARRY A., Second Training Camp, Ft. Sheridan, Ill. BAINS, THOMAS M., JR., Major, Engineer Officers&apos; Reserve Corps. BANKS, H. R., Lieutenant, Canadian Engineers, B. E. F. BARBOUR, PERCY E., Deputy Supt. (Captain), New York State Troopers; Captain, 22c1 Regiment, N. Y. N. G. BARLING, H. B., 1st Lieutenant, Engineer Officers&apos; Reserve Corps. BARRETT, LESLIE P., Lieutenant, A. E. F., France. (Unattached.) BENSEL, J. A., Major, Engineers&apos; Reserve Corps. BIGELOW, BRAXTON, Royal Engineers, B. E. F. BLOOMFIELD, E. C., Lieutenant. BORROW, F. K. BOWLES, MARTIN F., 2d Lieutenant of Infantry, Camp Funston, Kans.

Jan 10, 1917

By W. L. Phillips

Single crystals of aluminum, brass, and copper oriented for (100) and (110) slip were extended at 25°, 400°, and 600°C in simple shear. Aluminum specimens oriented for nonoctahedral slip began to shear at a higher critical resolved shear stress than specimens oriented for octahedral slip. Parabolic stress-strain curves were obtained from zero strain. The initial rate of parabolic hardening was lower for specimens sheared on the (100) plane in a close-packed direction <110>, than for specimens sheared in a nonclose-packed direction <100>. metallographic evidence, however, showed that all slip traces could be explained in terms of (111) <100> slip. All attempts to cause nonoctahedral slip in copper and 70-30 a-brass single crystals were unsuccessful. Instead of shearing, the crystals bent, allowing {111} type planes to come into action. NONOCTAHEDRAL slip in aluminum has been reported under three different conditions: first, as the main mode of slip in tension experiments at elevated temperatures;&apos;-&apos; second, as the main mode of slip in direct shear experiments at room temperat~re; and third, as a minor mode of deformation, i.e., as cross-slip, in tension, shear, and bicrystal experiments at room and elevated temperatures."-l2 However, as far as the author knows, nonoctahedral slip has not been reported in either copper or 70-30 a-brass. The present study was undertaken to determine whether nonoctahedral slip could be obtained in aluminum, brass, or copper at room or elevated temperatures when the shear stress was approximately constant over the cross-section, a maximum at the center, or a maximum at the surface. EXPERIMENTAL PROCEDURE A detailed description of the crystal preparation and shearing apparatus has been given previo~sly. Cylindrical crystals 1/2 in. in diam and 8 in. long were grown from the melt in a temperature-gradient furnace. The aluminum contained 0.001 pct Zn, 0.001 pct S, and 0.001 pct Fe; the 70-30 brass contained 0.015 pct Pb, 0.001 pct Fe, 0.01 pct Ni, 0.02 pct Sn, and 0.005 pct Se; the copper was certified OFHC of 99.98 pct purity. All samples were electropolished prior to testing. The shear apparatus was a modified Bausch type. The strain sensitivity was 4 x lob4 Load was applied by clamping the rods attached to the shear plates in an Instron tensile machine. The rate of loading was 0.02 in. per min. In all cases a 1/8-in. gage length was used. For the tests performed at 400° and 600°C the shear plates, collars, and rods were made of stainless steel. These elevated-temperature tests were performed in an argon atmosphere. A) Aluminum at Room Temperature. Values of a and ß for the various slip planes and slip directions investigated are shown in Table I where a is the complement of the angle between the specimen axis and the slip direction, and ß is the angle between the specimen axis and the normal to the shear plane. The shear stress is a function of a (assuming ß - 0);10 when a is less than 27 deg, the shear stress on the slip plane for which the specimen is oriented has a maximum at the center of the crystal; at a = 27 deg the shear stress is constant across the slip plane; for a greater than 27 deg the shear stress is a minimum at the center. Fig. 1 shows the stress-strain curves for specimens cut from crystals 1, 2, and 5, which were sheared on the (010) plane in the [loll direction at room temperature. These three crystals have shear-stress distributions corresponding to the three dif-

Jan 1, 1962

By Louis A. Panek

Caving of previously undisturbed ground was conducted for a period of about 20 months at two locations about 600 m (2000 ft) apart in an Arizona porphyry copper deposit. When mining was suspended the width of the mined zone at both sites was on the order of one-half the depth and the thickness of ore extracted was only a fraction of the rock column. Thus the results have potential application to predicting the subsidence above a cavern-type excavation. Break cables were used to detect the upward progress of caving. Analytical aerotriangulation was used to determine the vertical and horizontal displacements of 400-plus surface targets covering a 1585 m (5200 ft) square area. The measurements are summarized and interpreted with a view to predicting the rate of rise of a caving brow, detecting the initial surface subsidence, and characterizing the extent, the location, and the varying degrees of expected damage to surface facilities.

Jan 1, 1984

By William H. Emmons

Discussion of the paper of William H. Emmons, presented at the Canal Zone meeting, November, 1910, and printed in Bulletin No. 46, October, 1910, pp. 767 to S37. CHARLES R,. KEYES, Des Moines, Ia. (communication to the Secretary*) :-It is not in a spirit of criticism that I offer a supplemental suggestion or two on the subjects covered by this valuable and highly instructive memoir. There are two points which, in my opinion, should have received greater emphasis in Mr. Emmons&apos;s excellent paper. One is the fundamental role played by the chlorides under certain conditions in ore-formation. The other is the possible establishment of geographic relationships among the four phenomena of (1) excessive chloridic content of mine-waters; (2) the abundance of chloridic compounds of the precious metals ; (3) the presence of. manganese oxides; and (4) the diminishing importance, in ore-genesis, of the metallic sulphates. Although Mr. Emmons&apos;s notes refer to gold alone, it may be pertinently asked whether the same principles do not hold good for silver and copper also, since these metals form, together with gold, a distinct and well-known chemical group. That the reactions involved apply equally well to the other two metals mentioned, is shown by a number of recent observations and discussions. Chloridic ores of silver are, as I have lately endeavored to show, mainly worked in. arid or desert regions only ; and the great deposits of disseminated copper-ores are similarly characteristic of such regions, in which both classes doubtless owe their formation to the abundance of saline materials derived from desert dusts, and to the .plentiful and almost universal presence of manganese oxide. Under these climatic conditions, silver is somewhat more abundantly deposited than copper and gold, because its chloride is so much * Received Nov. 11, 1910.

Jun 1, 1911

By Erwin Zodrow, De Verle P. Harris

The Smallwood mine, owned and operated by the Iron Ore Co. of Canada, is one of the largest ore producers in Canada, producing about 15 million tons of crude ore per year. Located in the Labrador Trough near, Labrador City, Newfoundland, the open-pit operation has ore consisting chiefly of specular-hematite, with some magnetite. The magnetite content of the ore as a mineral percentage is small, but it is of considerable importance in ore grading because of its effect upon milling. Being harder than specular-hematite, magnetite increases grinding time and milling costs. Specifically, higher grade magnetite (greater than 15%) usually occurs as fine grains in a fine grained siliceous rock matrix (also as larger octahedra in carbonate bands). This tends to increase the overall breaking strength in the crude ore; consequently, the hourly mill rate and the weight recovery decrease. At the same time, because of its relatively high iron content, the magnetite does contribute to the amount of iron in a block of ore. Were the concentration of the magnetite relatively constant, its presence would be of less consequence, for appropriate adjustments could be made in the milling operations. However, the quantity of magnetite present for any run of ore varies considerably; it is the magnetite prediction for a block of ore that constitutes the greatest problem in grading. THE PRESENT ORE GRADING METHOD Ore for the Smallwood mine is graded by a computerized block grading routine (using 50 x 50 x 45-ft blocks) that applies simple weighted (inverse-distance) averaging to ore grades. The results of the block grading program are not reliable with respect to magnetite concentration. Factors responsible for this poor estimation are (1) the structural setting of the deposit, and (2) mineralogical relationships. Neither of these general factors are given adequate consideration by present methods.

Jan 8, 1967

By Kiyoshi Azuma, Hiroshi Kametani

The variation of the dissolution behavior of a ferric oxide with calcining temperature has been investigated. Samples were prepared by thermal decomposition of ferric hydroxide, nitrate, oxalate, and sulfate at low temperature, followed by the calcination in the temperature range between 600" and 1200°C. The samples of eight series and a fine crystalline sample of hematite were dissolved in 1 N hydrochloric acid at 55.2°C and the results are represented on double-log graphs for convenience. It is confirmed that all dissolution courses follouj either the accelerated process or the parabolic process except in the special case of the crystalline hematite which dissolced in accordance with the uniform dissolution of a particle. Examinations of the physical properties of the oxide powders revealed that the surface area measured by the permeability method is strikingly relevant to the dissolution behavior of the oxide. In the previous paper,&apos; detailed data were presented on the effect of the kind of acid, the solution temperature, and the concentration of acid on the dissolution of two ferric oxides. It was also shown that these sam ples dissolved in strikingly different ways. The present investigation was carried out on the dissolution of various calcined samples prepared from various ferri salts by various methods to ascertain the course of dissolution. Pryor and Evans2 pointed out a change of the dissolution rate at around 700°C for a series of calcined ferric oxides prepared from the hydroxide. Several papers374 reported also the dissolution of ferric oxide samples. It seems, however, that a systematic account of the relationship between the dissolution behavior and physical properties of the oxide has not yet been given. This paper presents the variation of the dissolution of the oxide in relation to the calcining temperature and the change of physical properties of the calcines. EXPERIMENTAL Raw materials were prepared by precalcination of ferric hydroxide, thermal decomposition of ferric nitrate, oxalate, and sulfate, and aerial oxidation of ferric chloride vapor, at as low a temperature as possible. The products were crushed, ground, if necessary, and sieved with a 100-mesh Tylor screen prior to calcination, after which the specimens were dissolved in acid solution. The following is a detailed description of the preparation of the samples. Sample H. About 500 g of ferric chloride (guaranteed reagent) were dissolved in 5 liters of deionized water and filtered. Ferric hydroxide was precipitated by addition of the minimum amount of ammonium hydroxide solution, and the precipitate was washed continuously till chloride ion was not detected by silver nitrate solution, and then filtered. The filter cake was dried at 120°C for a week and ground, and the -100 mesh portion was used. Sample S. Ferric sulfate (guaranteed reagent) was pyrolytically decomposed in a crucible at 700°C for 24 hr and the product was sieved. In this case the following calcination was carried out at temperatures over 700°C. Sample B. Commercial ferric oxide (guaranteed reagent). About 15 kg of ferric nitrate were decomposed in a furnace maintained at 800°C for 2 hr. The actual temperature of the decomposition was not measured. The product was crushed and sieved, and the -100 mesh portion was used. Sample N. About 50 g of ferric nitrate (guaranteed reagent) were decomposed in a beaker in a sand bath until a red-brown dense solid was produced. This product was crushed and sieved, and subjected to complete decomposition at 500°C. The precalcined product was again sieved and used. Sample N2.5. Since the decomposition temperature was not controlled for sample AT, a different sample was prepared in a temperature-controlled furnace. The subscript represents the decomposition at 250°C. The product was treated in the same manner as sample N. Sample Nc. Under atmospheric pressure it is prac-tically inevitable that ferric nitrate hydrate melts to form a brown liquid at about 50°C before pyrolysis. For this reason, the salt was first slowly heated under reduced pressure (about 10-3 mm Hg measured in a trap refrigerated by dry ice-alcohol) to achieve dehydration without melting. About 5 hr were required for the dehydration and the partial decomposition. Then the temperature was elevated to 500° C in air for complete decomposition. The relatively porous product was sieved and used. Sample Ov. About 200 g of ferric oxalate hydrate (extra pure) were dehydrated under reduced pressure (as described above) followed by thermal decomposition at 500°C for 6 hr in air. The decomposition of this salt was accompanied by liberation of carbon monoxide, by which the ferric salt was initially reduced to a black powder. The powder changed in turn into brown ferric oxide as the gas liberation decreased and reoxidation predominated. The product consisted of sparkling fine particles passing through a 100-mesh screen. However it was ground and sieved as for the other samples. Sample D. Commercial fine powder for magnetic tape purposes. The preparation was as follows.5 Ferric chloride vapor and preheated excess air were mixed and passed into a reaction tube where oxidation took place at 450°C. The fine powder formed was collected in a cottrell chamber. The product was vacuum-degassed at 450°C for 1 hr and sieved.

Jan 1, 1969

By R. H. Johnson

All strata not yielding oil or gas in commereial quantities or a corresponding amount of water may be called dry in a wide sense. In petroleum geology, however, we may exclude all sands of too low or fine porosity to yield gaseous or fluid contents to the hole drilled in the sand before any original pressure that its contents may be under is disturbed. Most rocks are of this class and they are not reservoirs in our definition; their "dryness" is wholly a matter of course. What are the contents of the pores or what is the exact porosity of such rocks is of almost no concern to us, for economically they are "dry." What does interest us is the content of a rock having sufficient porosity and the pores of sufficient size to yield oil or gas in commercial quantities, if they were present under original pressure. Dryness of these reservoirs is a matter of supreme practical importance. Three views current as to such dryness seem, to me, to apply in a few cases only. It is the purpose of this paper to give reasons for this position and for believing that, in ordinary sedimentary rocks, there is only rarely a reservoir of competent porosity and undisturbed pressure that is dry in the sense of not yielding water, oil, or gas when first penetrated. 1. Gardnerl writes of some Kentucky sands, "There has never been present any salt water or other water in the sand." Absence of water cannot demonstrate this position. It is necessary to show that the rocks were not laid down in water, but in air, and that they became so enclosed, while still above the water-table of the ground water, that water has not been able to enter since. Most of these sands, and certainly the productive limestones, were deposited in water; and such sands as have been commercially productive show no reason for believing that the overlying shale or limestone was not laid down progressively from one direction and in water that would have flooded it. NO adequate explanation has been offered for this hypothesis, which is so inherently improbable. 2, Reeves2 urges that "sands originally water filled may have been drained of their water and not filled when later covered." It is difficult I James H. Gardner: Kentucky as an Oil State. Science, N. S. (1917) 46, 279-280. Reeves: Origin of the Natural Brines of Oil Fields. Johns Hopkins Univ. Circ., N. S. (1917) N. 3; Absence of Water in Certain Sandstones of the Appalachian Field. Econ. Geol. (1917) la, 354-378.

Jan 1, 1921

(The following -list, contains the navies of those members of the Institute of whose connection with military service we have only recently become acquainted; it also includes the names of a few who have recently been promoted or transferred. A com-plete list was published in the Year Book, issued as a supplement of the Bulletin for March, 1918.) ADDICKS, LAWRENCE, Naval Consulting Board. ALINE, P. A., Camp Lewis. BARCUS, WALTER .J. E., Captain, Ordnance Department. BAUSH, JOHN R., Private, 1st Army Headquarters Regiment, Co. M. BENNETT, A. F., Lieutenant. BILLINGSLEY, PAUL, Engineer Officer, Aviation Section, Signal Officers&apos; Reserve Corps. BOOTH, L. E., Ordnance Department. BROWN, JAMES F., 2d, 1st Lieutenant, Ordnance Reserve Corps, A. E. F.

Jan 4, 1918

By C. B. Dudley

bas shown us that the railroads of this country can save several milt liohs a par by adopting uniform rail sections, and as unfortunately for him, he cannot patent his idea, it only remains for the railroads to adopt it, and to thank him for his payer. Dr. C. B. Dudley, Altoona, Pa. : 111 rising to close this interestin~ discussion, I want, in the first place, to thank every one who has contributed to it for his full and open criticism. The work tvhich has been done on steel rails, and which has been diwu&e,l here Juring thee two days, was not done to establish any pet theories, nor to make out that any person was great or any person small, but with a sincere desire to get at what is the truth in regard to the wedring capacity of steel rails. There are enormous commercial coneiderations invoIved in this question, and, as I look at the matter, the more honest criticism and fair discussion there is, the Inore likely it is that the truth will appear. Ad first I would like to say that it seems to me very little has been said here upon the main conclusion of the paper, namely, that the softer rails give the better wear. All sorts of side issues have been discussed; but this poiat, which is really the principal one at issue, has been largely ignored, aid I cannot But feel that it still remains unshaken. Witb regard to ohemists end chemical work, there has been considerable said tending to throw discredib on chemists and their work; and while I believe that there have been in the past, are now, and may be in the futnre, a good many poor chemical analyses made, X also believe that chemists are, as a rule, as honest and competent as gentlemen who belong to other professiomc. There are chemisb who are chemists, and who are not chemists. The determination of -manganese has bee* called in question. Now I think the chemist at almost every steel works in the country will tell you that, in his experience, the manganese diffe1.s in different parts of the same ingot. Mr. T. T. Morrell, chemist of the Camhria Iron Company, whom I believe to be s thoroughly competent and hone6t chemist, tells me that he has often found different amounts of manganese in different parts of the same ingot. Come with me to Altoona, and I will take you into the machine shop where steel is king cut aud shaped, and I will show you that it is often necessary to stop the lathe or planer and take a cold chisel to cut oat a hard spot, or else ntn the risk of breaking the tool. This hard spot is simply a pttrt of the syiegel which was not thoraughiy mixed with the ma

Jan 1, 1881

By R. S. Busk

A PREVIOUS paper1 has summarized the effect of A all metallic elements on the lattice parameters of magnesium. The present paper deals with the effect of temperature on the lattice parameters and the way in which that effect is modified by alloyed elements. The experimental techniques for sample preparation, exposure to the X-ray beam, measurement of line diameters, and calculation of the parameters were the same as reported in the previous paper. The temperature of the specimen was raised by surrounding the mounted compact with a conical Glas-Col,* the base of which was sealed with Saran film. In this way the temperature of the specimen could be raised to 200 °C, which was the maximum desired in the present study. Control of temperature was effected by maintaining a constant, desired voltage to the resistance coils of the Glas-Col through a Variac. Temperature was measured by an iron constantan thermocouple embedded in the body of the specimerl so that the thermocouple bead was within 1/16 in. of the surface exposed to the X-ray beam. Variation of temperature during an exposure was less than + 1/4 oF. A series of eight alloys, consisting of pure Mg, Mg+Ag, Mg+Al, and Mg+Sn were studied. All percentage values are in atomic percent. The results are given in Table I. The density values given in Table I were calculated from the lattice parameters, using an equation due to Foote and Jette:"

Jan 1, 1953

By P. W. Bennett, E. M. Elkin

A new technique for the recovery of palladium and platinum and sludge from go12 electrolyte eliminates many of the drawbacks of the zinc-dust cementation process. In the electrolytic refining of gold by the Wohwill method, the electrolyte contains about 100 gpl gold as AuCl, and 100 gpl free hydrochloric acid. Any palladium and platinum contained in impure gold dissolve and accumulate in the electrolyte. When their concentration approaches that of gold, it becomes desirable to discard the electrolyte and to recover the gold and the palladium and platinum. As practiced at Canadian Copper Refiners until recently, discarded electrolyte was treated with sulfur dioxide to precipitate the gold. 2AuCl3 + 6H2O + 3SO2 —2Au + 6HC1 + 3H2SO4 The gold precipitate was filtered off, washed with water, and melted with scrap anodes. The wash water was added to the gold-free filtrate and treated with zinc dust to cement the palladium and platinum. PdCl2 + Zn — Pd + ZnCl2 PtCl4 + 2Zn—Pt + 2ZnCl2 The precipitate was separated and sold as Pd-Pt concentrate, and the barren filtrate and wash water were discarded. The receipts of palladium and platinum at this company were too small to warrant their refining. The process suffered from a number of disadvantages. Handling the gold-free solution was disagreeable, as it was laden with sulfur dioxide even after blowing with air overnight. Subsequent treatment with zinc dust was also troublesome. A large excess of zinc dust was required. Spray, acid mist, and vigorous evolution of hydrogen accompanied the reaction. The Pd-Pt precipitate was grossly contaminated with occluded unreacted zinc and with yellow granules of sulfur, thought to be formed by the reduction of sulfur dioxide and its derivatives. Repeated boiling of the precipitate with hydrochloric acid and washing with water decreased somewhat, but did not eliminate, the zinc. After drying overnight, the precipitate hardened to a clinkerlike mass that was difficult to grind. Grinding, handling, and packing created heavy dusting. Even weighing in an analytical balance generated dust, indicating that the powder was easily charged with static electricity. The total palladium and platinum content of the powder varied from 56 to 72 pct, with an average of 65 pct. The powder dissolved in aqua regia with difficulty, leaving a small amount of insoluble residue. However, the main drawback of the process was the strongly hygroscopic Pd-Pt product. The powder showed a marked though erratic increase in weight and a corresponding decrease in assay on exposure to air, even during the course of laboratory analysis. Such changes were the source of disagreement between Canadian Copper Refiners and the buyers of concentrate. The cause of the change in weight is believed to be hydrogen, liberated by the action of zinc dust on hydrochloric acid. Some of this hydrogen was adsorbed so strongly by the precipitate that it could not be driven off during the drying. On exposure to air it oxidized catalytically, forming water. Experiments soon showed that the entire process of treatment of discarded electrolyte then in use would have to be changed. A small quantity of apparatus was moved into the gold room, and experimentation was held to a minimum compatible with the development of a new process. PALLADIUM AND PLATINUM PRECIPITATION It was thought that zinc could be replaced with a reagent other than a hydrogen-evolving metal. Semiquantitative experiments showed that platinum and palladium could be precipitated completely from the gold-free solutions with such well-known reagents as sodium formate, formic acid, formaldehyde, and paraformaldehyde. Sodium formate was the preferred reagent, since the other three are volatile and somewhat toxic. The gold-free solutions used were those saturated with sulfur dioxide, partly freed of sulfur dioxide by aerating overnight, completely freed by boiling, as well as strongly and weakly acidic, neutral, and alkaline solutions. The reactions are complex and can be represented by these over-all equations: PdC1, + HCOONa — Pd + NaCl + HC1 + Co2 PtCl4 + 2HCOONa — Pt + 2NaCl + 2HC1 + 2CCX, Strongly acidic solutions required as much as five times the theoretical amount of sodium formate as did solutions neutralized to pH 4.5. Increasing the pH decreased the consumption of

Jan 1, 1965

By BARONJUPTNER VON JONSTORFF, Andrew A. Blair, GUNNAR DILLNER

IT is a well-known fact that the results of different analysts, when operating on the same identical sample of steel or iron, are far from concordant, and it not infrequently happens that great annoyance and trouble in the commercial community are occasioned by these discrepancies. Attempts have been made at various times to investigate the causes of such differences and to obtain more reliable methods of analysis. The most important of these was made by the British Association in 1889: The following gentlemen, with Sir W. Roberts-Austen as Chairman, and Professor T. Turner as Secretary, were constituted as a committee to investigate the question, viz.: Sir F. A. Abel, Mr. Edward Riley, Mr. G. J. Snelus, Mr. John Spiller, Professor J. W. Langley, and Professor Tilden. Average .samples of steel were prepared in America under the superintendence of Professor J. W. Langley. The steels, in the form of turnings, were divided and distributed to sub-committees in Great Britain, America, France, Germany, and Sweden. In Sweden Professor Åkerman acted as Secretary to the Swedish committee. The Government Department of Tests was appointed in Germany; Mr. Ferd. Gautier in France; the British Association Committee in England; Messrs. William

Mar 1, 1905