Search Documents

By George J. Young

(San Francisco meeting, October, 1911.) THE nature of slimes handled in the treatment of gold- and silver-ores has been discussed in technical literature to a considerable extent. The subject of slime-filtration from the practical worker's stand-point has also received much comment, and scattered through the literature of the subject are descriptions of many slime-filtration installations. Articles of this nature serve a valuable purpose and assist materially in the design of new and the improvement of old plants. The subject of the physics of slime-filtration has been touched upon to only a slight extent. The underlying principles are worthy of more intensive study and experimentation than they have received, and the main purpose of this paper is to present the results of such study and experimental work as will serve to make clear in part at least many of the principles which control the filtration of slime. Nature of Slime. Much has bean written concerning an accurate definition of the term ? slime," but no comprehensive definition seems to be generally accepted. The reason for this is clear. A slime consists of at least three different substances, each, when separated, possessing distinctly different physical and to a certain extent chemical properties. These substances are extremely fine sand, a colloidal material which may be and generally is in a coagulated condition, and a colloidal material which is in a non-coagulated condition. Suspending a slime in a relatively large volume of water by shaking and allowing sedimentation to take place, results in the fine sand settling out with comparative rapidity, followed by the coagulated material, which settles much more slowly and finally a certain portion remains

Nov 1, 1911

By J. D. Ridge

The geologic setting and mineral relationships of seven European massive sulfide deposits that more or less conform to the bedding of the largely noncal-careous sedimentary rocks and/or bedded volcanics in which they are found are considered here. These orebodies consist largely of massive beds or lenses of sulfides usually surrounded by halos of disseminated sulfides and distorted by tectonic activity. The formations containing these deposits have been metamorphosed in varying degrees at times subsequent to their lithification. The ore-forming process is thought to be essentially volcanic, with the ore constituents being brought to the shallow-water site of deposition through tectonic fissures from magma chambers at depth as gases or relatively concentrated hydrother-mal solutions. Certain European ore deposits of base metal sulfide have previously been considered to be of hydro-thermal or magmatic origin, but today a number of European mining geologists consider them to be syngenetically produced. In an effort to provide American geologists with some idea of the reasons behind this change in thought, the geological settings of seven of these deposits have been studied. These are: Ldkken, Meggen, Rammelsberg, Ergani-Maden, Outokumpu, Boliden and Roros. These deposits lie in bedded rocks that have undergone metamorphism from causes not universally agreed upon; most of the formations were originally shales, and may have been intercalated with limey and occasionally quartzitic beds, volcanic tuff, agglomerate, extrusive lavas and usually basic intrusives. Deposits of the conformable type, however, are not confined to these rock types but may be in calcareous and associated igneous rocks or almost entirely in volcanics. These deposits may be closely associated in space with igneous rocks that, again, are usually basic types. Although the ages of the enclosing rocks range from mid-Precambrian (Boliden and Outokumpu) to Eocene (Ergani-Maden), the bulk of them are Paleozoic, with two (Meggen, and eammelsberg) being upper middle Devonian and two (LØkken and RØros) being Cambro-Ordovician. Geographically, two are in West Germany, four in Scandanavia and one in Turkey. Of the seven deposits, six are mined for copper, with three of these also producing zinc, and two lead; one is mined for zinc and minor lead. In the discussions of the seven conformable deposits that follow, I have attempted to present as uniform a treatment as their varying characters will permit. For each deposit, I have considered the stratigraphy of the area, its major structural characteristics, the form of the orebodies, their mineral content, and the origin of the ore. In the last of these subdivisions, I have presented only the viewpoint of those who believe the ores to have been formed by syngenetic processes, processes that went on at the same time as those which produced the beds that enclose the ores but that are not, in the deposits in question, thought to have been sedimentary in the strict sense of the term. The materials of which these orebodies are composed, it is suggested, did actually collect by falling through sea water to the floor of that portion of the sea in which they accumulated. The ore constituents, however, are believed by a considerable number of European geologists to have been added to the sea water from intratelluric sources, probably igneous magma chambers, as exhalations — hydrothermal solutions or volcanic gases. The effect of the encounter with sea water on these ejected gases or water-rich vapors was to precipitate their potentially solid constituents with great rapidity; they were deposited so quickly, in fact, that the amounj of normally accumulated mechanical or chemical sediment deposited over the same period of time was essentially negligible. The ores formed in this manner, however, are generally interbedded with normal sediments or with lava flows, or with any combination of these two types of rock-forming materials. Such departures as these deposits may have from their original mineral content and attitude are thought to be directly related to the degree of dynamic or static metamorphism that they may have undergone after their accumulation. I have not attempted here to present alternate hypotheses to that of so-called exhalative sedimentation although, of course, such exist and, in my

Jan 1, 1963

By Kehsin Kuo

DIE steel with 1.47 pct C, 0.42 pct Mn, and 8.22 pct W contains Fe,C and WC in the annealed state and WC embedded in a martensitic matrix in the hardened state (quenched from 800°C). The presence of a large amount of undissolved angular WC carbide particles makes this steel extremely wear-resistant. However, the WC carbide begins to dissolve in the austenite when the heating temperature is raised above 1000°C, but this solution process is still not complete at 1250°C although partial melting has already taken place at the austenite grain boundaries. At 1325 C, this steel contains austenite and liquid metal but no WC carbide, Fig. 1. On quenching into brine, the liquid metal solidifies into a constituent which etches differently from the austenite-martensite matrix. This constituent appears lighter than the matrix at the 1250°C stage when etched with 2 pct nital but darker in Fig. 1 when etched with Murakami's reagent. Such a constituent has also been found in burnt tungsten high speed steels. This constituent has been isolated from the matrix by anodic dissolution in a 5 pct HC1 electrolyte and was found by the X-ray powder method to be iso-morphous with &manganese, Table I. The agreement in line intensity between these two phases indicates that there is no ordering in this new phase. The calculated cube edge of this phase is 6.395A, somewhat larger than that of ß-manganese (6.30A). Besides this phase, the anodic residue also contains free carbon from the matrix and amorphous WO,, although the X-ray powder pattern of the residue shows the presence of only this phase. This makes it impossible to determine directly the composition of this phase from the residue. Attempts to prepare an alloy containing only this phase have hitherto been fruitless. The following experiments serve to show that this phase can only be obtained by drastic quenching from the liquid state and that its tungsten and carbon contents must be lower than those in the Fe,W,C carbide. On air cooling from 1325oC, the liquid metal solidifies into a eutectic consisting of austenite and the Fe3W3C carbide. The nature of this dark-etching Fe3W3C has also been ascertained by X-rays. This eutectic becomes coarser on furnace cooling. The solidification of a specimen cooled for 5 min from 1325" to 1200°C and water quenched is still not complete and the fine eutectic is formed during the quenching. Since this new phase can be replaced by a eutectic of austenite and the Fe,W,C carbide, its composition must lie somewhere between the latter two phases. The special features of this phase are: 1—it can only form directly from the liquid state by drastic quenching and 2—it is a ternary phase of iron, tungsten, and carbon. The ß-manganese structure of this phase is also interesting. In the Periodic Table, iron and tungsten lie on opposite sides of manganese; a certain combination of these two elements, in the presence of carbon, may have average properties similar to those of manganese. It has already been established that the x phase, a ternary one of iron, chromium, and molybdenum, has the a-manganese structure."' A similar phase has also been found in the ternary system Fe-Cr-W and in the following binary systems: Re-Cb, Re-Ta, Re-Mo, and Re-W.6 References 1 G. D. Preston: Philosovhical Magazine 11928) 5. 7th Series, p. 1207. - K. W. Andres: Nature (1949) 164, p. 1015. 35. G. McMullin, S. F. Reiter, and D. G. Eberling: Trans. ASM 11954) 46, p. 799. ' J. S. Kasuer: Acta Metallurgica (19541 2, p. 456. • H. J. Goldschmidt: Trans. ASM (19541 46, p. 807. P. Greenfield and P. A. Beck: Private communication.

Jan 1, 1957

By Bobby P. Faulkner

The Tennessee Copper Co.'s flotation plant, refer- T red to as London Mill, processes approximately 4800 tons of a massive complex sulfide ore per day. The ore is predominantly pyrrhotite and pyrite, the other sulfides being chalcopyrite, sphalerite, and a small amount of galena. Magnetite of economic value is also present. There are four concentrates produced. In decreasing tonnage, these are iron, copper, zinc and lead. The ore feeding the mill is a composite of ores from five mines which vary in grade. Therefore, in order to provide a fairly constant feed to the mill, the ore is blended several times before reaching the flotation machines. The flotation plant is divided into three main sections: bulk, copper and zinc. Fig. 1 shows a simplified flowsheet. The first two sections, the bulk and copper, were the two sections studied most closely in utilizing the computer.

Jan 11, 1966

By C. Land, R. Hultgren

Heat contents of four Cr-Ni alloys were determined in a diphenyl ethev calorimeter. Aside from ferromagnetic effects, Kopp's law of additivity of heat capacities is approximately fol-lowed, in disagreement with earlier results of A. W. Foster. In 1934 Foster1 reported heat-capacity measurements of dilute solutions of chromium in nickel, primarily as a study of the effect of alloying on the ferromagnetic Curie temperature. He found that, apart from the Curie temperature effect, the general level of heat capacities was reduced 10 pct by the addition of 1 pct Cr; 20 pct by the addition of 2 pct Cr. His measurements of pure nickel essentially agreed with accepted values. These results indicate that small amounts of dissolved chromium cause an increase in the Debye temperature of nickel, presupposing a change of frequency of interatomic bonding vibrations which is much larger than should be expected. If Foster's results were verified, therefore, they would have important implications for bonding theory. The only other heat-capacity measurements in this system seem to be those of Taylor and Hinton,' who studied anomalies which they attributed to super-lattice formation at 25 at. pct Cr. At temperatures above the anomaly, Taylor and Hinton found heat capacities at this composition were quite normal, approximately obeying Kopp's law of additivity. EXPERIMENTAL WORK In order to verify or disprove the remarkable results of Foster, the heat contents of four dilute solid solutions of chromiunn in nickel were measured in a diphenyl ether calorimeter. This instrument, described elsewhere,, operates on the principle of the Bunsen ice calorimeter, but uses diphenyl ether as the working substance. Diphenyl ether melts at the convenient temperature of 26.S°C and supplies a more sensitive measure of heat than ice. The hot sample, in an atmosphere of argon, is dropped from a furnace at a measured temperature into a chamber which is surrounded by a mixture of solid and liquid diphenyl ether. The heat from the hot specimen melts some of the solid without chang- ing the temperature of the calorimeter. The amount of solid melted, and therefore the number of calories released by the specimen, is measured from the increase of volume of the mixture, which pushes mercury down a graduated capillary tube. The apparatus has been standardized against the known heat content of pure platinum. Heat loss during the dropping of the specimen was estimated by comparing the heat content of an empty platinum capsule with a solid platinum ball of the same radius and degree of polish of the surface. Repeated tests demonstrate the precision of measurement to be closer than *0.3 pct. Smoothed experimental results are listed in Table I. The tabulated values for pure nickel are taken from kelley, several measurements were made which agreed closely with this tabulation. For chromium, however, no similar agreement was found. The values tabulated were taken from a thorough study of chromium with the diphenyl ether calorimeter which will be published elsewhere.= Suitable plots of the data showed the expected ferromagnetic anomalies in the low-chromium alloys, while the 11 pct alloy shows no ferromagnetic anomaly, but a different, small anomaly below 900°K. This is perhaps the same anomaly found in CrNi, which was once attributed to superlattice formation,' but is probably due to some other cause, such as antifer-

Jan 1, 1960

By R. J. Woody

Design of the most economic continuous counter-current decantation (CCD) circuit is based on selection of the number of stages and the wash volume that will give the minimum summation of the following items: 1) Capital and operating costs of the CCD circuit. 2) Capital and operating costs of the precipitation circuit. 3) Value of the dissolved product lost.

Jan 1, 1959

By A. S. Keh, H. A. Wriedt

The Precipitation of nitrides in quenched Fe-N alloys, aged between 25° and 200°C, was studied by transmission electron microscopy. Different dislocation substructures were introduced into the materials by recrystallization, cold working, and by Phase transformation prior to the introduction of nitrogen. It was found that the precipitated nitrides, tentatively identified as Fe16N2, have (100) habit planes. Nucleation takes place Preferentially at dislocations and at subboundaries. It sometimes occurs in the matrix, probably on vacancy clusters, but rarely on high-angle boundaries. The process of nucleation on dislocations and subboundaries is very temperature dependent. At room temperature there is no particular orientation relationship between the dislocations involved and the (100) planes on which the nitride Particles formed. With increasing temperature, the nucleation sites tend to become restricted to those dislocation segments lying in (100) planes. The change of yield stress of the 0.022 and 0.043 pet N alloys during quench aging can be correlated semiquantitatively with the change in particle distribution. Strain aging in quenched alloys can be separated into two stages. The early stage is attributed to nitrogen segregation to dislocations and the later stage is associated with precipitation. When previously quench-aged specimens were strained and aged, no additional Precipitates could be seen, although a considerable amount of strain aging occurred. DURING the past two decades, the precipitation of nitrides from a iron has been extensively studied by various techniques. It has been established that two types of nitride exist. The stable nitride, Fe4N, forms at temperatures above 250oC and Fe16N2, the

Jan 1, 1962

By J. R. Morison, M. P. O’Brein, J. W. Johnson, S. A. Schaaf

The force exerted by unbroken surface waves on a cylindrical object, such as a pile, which extends from the bottom upward above the wave crest, is made up of two components, namely: 1. A drag force proportional to the square of the velocity which may be represented by a drag coefficient having substantially the same value as for steady flow, and 2. A virtual mass force proportional to the horizontal component of the accelerative force exerted on the mass of water displaced by the pile. These relationships follow directly from wave theory and have been confirmed by measurements in the Fluid Mechanics Laboratory of the University of California, Berkeley. The maximum force exerted by breakers or incipient breakers is impulsive in nature, reaching a value much greater than that produced by unbroken waves but enduring for only a short time interval. This impulsive force represents the ultimate development of the accelerative force and is produced by the steep wave front and large horizontal acceleration at the front of a breaker. This impulsive force greatly exceed. the drag force computed from the particle velocities of the breaker. The reader is cautioned that these preliminary results are applicable only to single piles without bracing and are likely to be modified somewhat where multiple piles are driven, one within the influence of the other or where multiple piles are connected by submerged bracing. This paper is essentially a preliminary report submitted at this time because of the current importance of wave forces in the design of offshore structures. An extended series of additional experiments is planned for the near future. Theoretical Relationships For the sake of simplicity of treatment, the theory will be developed from the equations for waves of small amplitude. The horizontal displacement of a water particle is described by the equation 2p cosh — (d + z) H L 2pt X =----------------------sin ----- . , (1) 2 2pD T sinh------ L The horizontal component of the orbital velocity is obtained by differentiation with respect to time as 2p cosh — (d + z) pH L 2pt u = ------------------- cos— .... (2) sinh- L The acceleration of the water particles at any position is obtained by again differentiating with respect to time as 2p cosh — (d + z) 9 u -2vH L 2pt -----=----------------------------sin ----- . . (3) 3 t T2 2pd T sinh------ L where H = wave height — ft L = wave length — ft d = still water depth — ft z = depth below the still water measured negatively downward — ft. T = wave period — sec t = time — sec The force exerted on a differential section, dz, in length is pD2 s u pD 1 dF= [CM (p/4) st + Cn/2 u2] dz • • (4) where D = pile diameter — ft p = water mass density — slugs/ft3 C, = coefficient of mass C,, = coefficient of drag Substituting for a s u/s t arid u2 from Eqs. (3) and (2), the force per unit length at any position z is dF p2 pD H2 &apos; / = — [- fM sin ? ± fD cos2 ? ] . . . (5) dz 2T2 fM D fD 2pt Cm = pA/H:CD = A2;? = T [+ cos2 ? for 0 < ? < p/2 cosh— (d+z) 3p L — < o < 2p Sin L -cos2 ? for p/2 <? <3p/2 The sin 9 term (inertia) i- negative for 0 < 0 < p and positive for p < ? < 2p. Values of A and A&apos; appear in Fig. 1

Jan 1, 1950

By H. Y. Jennings

An extensive field and laboratory experimental program was carried out to compare the waterflood behavior of carefully preserved soft and unconsolidated cores with measurements on the same cores after extraction. Results obtained from using idealized consolidated and unconsolidated porous media in which wettability could be carefully controlled were contrasted with the preserved core data. The controlled tests on idealized porous media investigated the effect of wettability, flood rate, core length, core permeability and consolidation on the displacement of high viscosity oils. It was concluded from these studies that waterfloods are more favorable when carried out with crude oil in preserved soft and unconsolidated cores than with the same cores after they have been extracted and re-saturated. Waterfloods are usually more favorable when carried out with crude oil in extracted .soft and unconsolidated cores than with refined oil of the .same viscosity in the same cores. The less favorable behavior of extracted soft and unconsolidated cores compared to preserved cores is due to alteration of the core by extraction. Preserved cores saturated with native water and oil should be used for laboratory displacement experiments because they more accurately reflect true reservoir behavior INTRODUCTION The demand for low gravity crude oil created by refinery modernization has focused attention on increasing the production of this viscous crude oil. Billions of barrels are in place in fields that are depleted, or nearly depleted, by primary production mechanisms. Since low gravity reservoirs are relatively recent, geologically, the solid matrix material is usually soft and unconsolidated sand. Such formations are also characterized by a high clay content. Evaluation of sophisticated oil recovery processes with the associated high capital investments has increased the demand for special core analysis tests on material from these soft and unconsolidated sand reservoirs. Data in this paper have resulted from an extensive field and laboratory experimental program. The initial objective vras to provide soft and unconsolidated sand cores for laboratory measurements with as little alteration as possible from their reservoir condition. A secondary objective was to compare the waterflood behavior of these carefully preserved cores with measurements on the same cores after they had been extracted and resaturated. When the comparison showed markedly different behavior the final objective was to attempt to explain the difference by making measurements on idealized porous media free of clay in which initial wettability could be carefully controlled. EXPERIMENTS MATERIALS Core Material The preserved cores used in this study were obtained with as little alteration as possible from their reservoir conditions. Special techniques were developed to satisfy this objective. The cores were cut with native crude whenever the crude had the necessary properties to satisfy the minimum drilling fluid requirements. A pure hydrocarbon chromatographic tracer was added to the crude to provide a simple, safe and inexpensive method to distinguish between oil filtrate and formation oil. Details of the tracer technique used in this study and the procedures used to handle and process the soft, unconsolidated cores have been published.&apos; The core samples were then preserved and packaged at the well site with a dip-applied strippable plastic, or by using a rubber sleeve from a rubber-sleeve core barrel. The final step was to insure that the carefully taken and preserved samples were not altered by processing in the laboratory. Some soft and poorly consolidated sands were carefully shaped in the lab and encased in a protective mounting without disturbing their three-dimensional integrity. Many samples were so poorly consolidated that they literally flowed from the package when the seal was broken. A technique was developed to obtain cylindrical plugs from these samples by using liquid nitrogen as the drilling fluid in a conventional core-drill, drill-press assembly. The idealized porous media consisted of sintered rods of Alundum RA 139, outcrop sandstone identified as Al-hambra sandstone and packs of No. 130 Nevada sand. This sand is 95 per cent 140-200 mesh. (Physical properties of these porous media with those representative of preserved cores are in Table 1.) The natural cores and most of the idealized porous media were 1 1/2-in. in diameter and 3-in. long. The samples used to study the effect of core length were 1 1/2-in. in diameter and 12-in. long. Liquids Water and oil produced from the formations being studied were protected from the atmosphere and collected in carefully cleaned glass or plastic-lined containers. The production was free of chemical additives such as emulsion breakers and corrosion inhibitors. The crude oil was

Jan 1, 1967

By D. S. Choi, R. Stefanko

There are a number of complex factors that influence the effectiveness of anchorage to maintain tension in rock bolts. However, a plastic analysis of the anchorage site employing certain simplifying assumptions with application of the Mohr-Coulomb criterion appears to explain the observed phenomena. Such an analysis has been made and a correlation sought with field and laboratory tests. Field tests were made in an anthracite mine in eastern Pennsylvania and included pull tests and long-term tests of a variety of anchorage devices in two basic lengths, 30 and 42 in. in two widely differing seams. Performance is reviewed for wedge, expansion shell, and resin anchorage. Laboratory tests duplicated many of the field conditions but in addition compared the performance of shells with normal and reversed serrations. This performance was compared with the predicted results from the plastic analysis. One of the major problems in conducting long-term underground tests is the selection of suitable instrumentation. All installed bolts were fitted with spherical and hardened washers to insure the best possible torque wrench readings. In addition, commercially available load cells were used. Finally, the performance of a specially developed strain-gage-equipped ring cell is viewed. Rock bolting as a method of support continues to increase with applications in many other industries in addition to mining. Nevertheless, with nearly 55,000,000 roof bolts installed in coal mines alone last year, this remains as the single greatest use. While bolts have frequently supported ground where conventional timbering could not, there are relatively few design criteria; and trial-and-error procedures prevail. Furthermore, there has been a lag in development of suitable instrumentation that is simple to install and read out, sensitive, durable, reliable, safe, and economical in evaluating the effectiveness of a bolt over long periods of time. Therefore, the pull test continues to be the most popular method of evaluating the applicability of a certain type of roof bolt under specific installation conditions. At The Pennsylvania State University in the Dept. of Mining, research has been conducted for a number of years to measure bleed off in carefully controlled laboratory experiments as well as in underground investigations."-&apos; Unfortunately, most of the instrumentation developed has been primarily suitable only for research purposes, not possessing all of the aforementioned characteristics desirable for routine underground use. Other groups also have met with restricted success. Therefore, while relatively crude, the torque wrench continues to remain as the most widely used load measuring device. While both field and laboratory tests continue to be con- ducted, analytical analyses are attempted to discover the more important design parameters in order that more efficient anchorage might be devised. Bolts are being used for a greater variety of purposes in mining. Suspending wire sideframe belt conveyors from roof bolts is a common application. The suspension of a monorail transportation system presents yet another. One such system has just been installed in a recently reopened anthracite mine and is presently being evaluated under production conditions. Preliminary studies revealed that a considerable cost reduction was possible by suspending the monorail on bolts anchored in the top. The monorail was to be installed under two widely differing conditions—a competent sandstone above the Buck Mountain seam and a softer shale top above the Skidmore. The type of anchorage device, length of bolt, and long-term performance, consistent with economy and safety, had to be established for the installation once the decision was made to suspend the system on rock bolts. This paper describes some of the testing procedures leading to a final selection. Theoretical Analysis of Expansion Shell Anchorage A detailed look at an expansion shell assembly might shed some light on the factors involved in the design of a suitable shell, Fig. 1. When a bolt is rotated, the tapered plug is forced downward, expanding the leaves laterally to grip the sides of the hole. Two friction surfaces are present: (1) the interface of the plug and leaf and (2) the interface between leaf and rock. The relationships of these friction planes, geometry of expansion shell, and properties of the rock are important in the design of an expansion shell. Therefore, an analysis assuming the rock to behave as a rigid plastic material with its yield governed by the Mohr-Coulomb criterion was made." Furthermore, the effect of friction between the leaf and rock produced by serrations was analyzed.

Jan 1, 1971

By Larry Dale

An approach for predicting the development of mineral resources on public lands has been developed as an aid to resource agencies. It consists of new techniques for evaluating the economic potential of the resource, the uncertainty about mine cost estimates, and the uncertainty about the occurrance of mineral deposits. New mineral sup- plies from inferred and hypothetical resources can be predicted by using these techniques. A case study illustrates their application in predicting development of copper resources in western Montana.

Jan 1, 1982

By Fitterer, G. R.

The impact of the work of Herty "et al" on modern liquid steel technology can only be evaluated by first setting the stage as it existed in 1926. It is important to briefly review not only the steel making process and viewpoints regarding methods of refining, but also to describe the tools which were available for research at the time. One must recall that only 15 years before the beginning of this program, the open hearth production exceeded that of the Bessemer in the United States. Many open hearths were still operating on producer gas (a very inefficient fuel), although some plants were converting to the use of natural gas and very few to oil. Continuous rolling of wide strip started this year. The Faraday Society in England held a World Conference on Physical Chemistry in Steel Making in 1925 and the contributions to this work created considerable interest throughout the world and it appeared that physical chemistry might convert the art of steel making into a science. These papers, however, attempted to solve the problems through the use of the older physical chemical concepts such as Nernst&apos;s numbers, etc. and considerable data were missing. In 1923, Lewis and Randall had published their book Thermodynanzicsl and this was later to establish and standardize the steps which are now accepted for the calculation of physico-chemical equations. At the time this research work was started, there were no small high frequency induction furnaces. Northrup had just invented his high frequency furnace and a few large units had been instilled in plants. The vacuum fusion method lor the determination of oxygen in steel was

Jan 1, 1957

By Thomas T. Read

The purpose of the following research, as originally planned, was to investigate the influence of temperature upon the plate¬amalgamation process. In order to consider the amalgamation process intelligently, it was first necessary to learn the nature of an amalgam. In the performance of this task it was found necessary to consult a large volume of literature and to perform experimental investigations. The conceptions of the nature of amalgams thus obtained have so important a bearing on the amalgamation-process as a whole, as well as upon the possible influences of temperature, that it was advisable to include them in the treatment of the subject. The broader title is therefore used, even though some features of the amalgamation process have been treated very briefly and others entirely omitted, there being nothing new to present regarding them and their development not required for a clear presentation of the matter in hand. I. HISTORICAL INTRODUCTION. Gold was one of the earliest metals known to man. Occurring in the metallic state, it could be picked up in nuggets or washed, as gold dust, front the sand and gravel of streams. Interesting descriptions of the processes employed in early times for the recovery of gold may be found in Pliny&apos;s Natural History and in the treatise by Agricola on ores and minerals. But little progress in the treatment of the ores of gold was possible until efficient -crushing machines were devised. This want was supplied by the introduction, about the beginning of the sixteenth century, of the stamp mill to treat the ores of Saxony. Blanket strikes, or similar devices, were used to catch the

May 1, 1906

By Neville J. Price

In order that the reader may not be misled, I feel it necessary to comment upon the title of this paper. "Laws of Rock Behavior," one may take as being part of the all-embracing "Law of Nature" and this, according to the Oxford Dictionary, relates to the principles of conduct recognized as being pleasing to God. I feel it would be presumptuous to erect a code of rock behavior on this basis, so turn to a secondary definition, namely that a "Law" is that which is intrinsically reasonable. It is extremely unlikely that any group of geologists, or workers in rock mechanics would be in complete agreement about what could be taken to be "intrinsically reasonable." Therefore, this paper does not present any deified utterances, but rather deals with a few aspects of rock behavior which I consider to be intrinsically reasonable and with which I hope the reader will concur. The mode of behavior of rocks in the Earth&apos;s crust covers the range from wholly brittle to completely ductile ; with a deformation time scale which may be measured in milliseconds, for some events such as meteoritic impact, or in millions of years for the tectonic deformation involved in mountain building. A complete survey is, of course, outside the scope of an introductory paper, so I must be both brief and selective in my treatment. Any attempt to establish the mode of rock behavior in the Earth&apos;s crust should take into account data and relationships established in laboratory experiments and correlate these with field evidence. Consequently, the first section of this paper presents a brief discussion of the experimental aspects of rock mechanics which are pertinent to the subsequent discussion.

Jan 1, 1970

By G. K. Manning, P. C. Rosenthal

USE of copper as an intentionally added alloy in steel and cast iron has rapidly expanded with-in the last fifteen years. It is estimated that in 1931 not more than 2000 tons of copper were so used; by 1941, however, this figure had grown to 13,000 tons. Tonnage figures during the war years have been restricted just as copper itself has been restricted, but copper-bearing cast irons and steels have played a part in the production of ordnance equipment. They are used in gun carriages, airplane landing-gear assemblies, scout cars, bulldozing equipment, army trucks, armor plate and many other instruments of war. These wartime applications have their counterpart in many peacetime applications; derricks, dredges, mine equipment, railway equipment, trucks, farm implements, automobiles, and tractors, all usually contain some parts made of copper-bearing steel or iron. An example of this is the Ford tractor which in 1940 contained over 300 lb. of copper-bearing steel castings. To this list should be added corrugated building sheet for exterior use most of which, at the present time, contains upward of 0.15 per cent copper. With the return to peacetime economy and the removal of wartime restrictions, it appears certain that copper cast irons and steels will find increasing application in civilian goods.

Jan 1, 1945

By W. Rostoker

IN the course of the development of the phase equilibrium diagram for the system Zr-Cr,&apos; the structure of an as-cast allov having the composition ZrCr2 was analyzed and established to be isomorphous with MgZn2 (C14, hexagonal lattice, 12 atoms per unit cell). In a recent paper on the same system, Hayes, Roberson, and Davies&apos; report for the ZrCr2 phase an isomorphy with MgCu2 (C15, cubic lattice, 24 atoms per unit cell). It appeared that this conflict might be resolved by assuming a high and low temperature modification for ZrCr2. That this was the case with the phase TiCr2 has recently been demonstrated by Levinger." Specimens of ZrCr2 annealed at 1200°, 1100°, 994", 900°, 834", 800°, and 700°C, respectively, and subsequently quenched were examined by X-ray diffraction analysis. It was successfully demonstrated that a transition from the MgZn, structure at lower temperatures to the MgCu, structure did occur at some temperature between 900" and 994°C. Table I lists the observed structures at the various annealing temperatures. In Table II, a summary of line spacings and intensities is given for each of the allotropic modifications. The first six lines of the MgCu2 structures have been located in the table to illustrate the close similarity between the patterns. Lattice parameters of the two modifications were calculated by a least squares solution of equations for interplanar spacings for a series of high angle lines. The results are as follows: MgZn2 type - c = 8.262 kX, A = 5.079 kX. MgCu2 type — a = 7.195 kX. It is interesting to note that TiCr2 behaves in reverse fashion yn that the MgCu, structure is the low temperature modification and the MgZn2 structure is the high temperature modification. References lR. F. Domagala, D. J. McPherson, and M. Hansen: This issue p. 279. &apos;E. T. Hayes, A. H. Roberson, M. H. Davies: Trans. AIME (1952) 194, p. 304; Journal of Metals (March 1952). 3B. W. Levinger: Trans. AIME (1953) 197, pp. 195-196; Journal of Metals (February 1953).

Jan 1, 1954

By E. J. KENNEDY

METHODICAL AND EFFECTIVE: thus may be characterized the fall meeting of the Iron and Steel and Institute of Metals Divisions at the Hotel Statler, Buffalo, N. Y., on Oct. 4 and 5. Approximately 200 registered. Interest centered 1111 the technical papers which were keenly followed, with substantial discussion: During the entire week of the National Metal Congress (Oct. 3 to &apos;i), there were also other sessions of interest&apos; to metallurgists, directed by the America11 Society for Steel Treating, American Welding Society, Production Division of the Society of Automotive Engineers, the Iron arid Steel and Machine Shop Practice Divisions of the American Society of Mechanical En,&apos; the Wire Association and the American Drop Forging Institute. The National Metals Exposition at the 174th Regiment Armory was well attended.

Jan 1, 1932

By John Henry Harden

This shaft, located in the northern anthracite coal-field about 2300 feet southwest from the court-house at Wilkes-Barre, in the County of Luzerne, Pa., is the property of the Lehigh & WilkesBarre Coal Company. The sinking and cribbing to the solid rock (see isometrical view on Plate IX) was conducted by Mr. W. W. Kenrick. Dimensions of the earthwork to the foundation of the cribbing, 51&apos; 2" long, 17&apos; 4" wide, 31&apos; deep. Total amount of excavation in cubic yards, 998.5. Dimensions within the permanent cribbing, 45&apos; 4" long, 11&apos; 16" wide, 31&apos; deep, divided into six parts by buttons 8" x 12", each division, 7&apos; x 11&apos; 6". Permanent cribbing 12" x 12"; temporary cribbing 8" x 10" ; backing, 3" thick ; clay puddle to exclude surface water, 12" thick; conductors, 8" x 5"; lining, 1" thick from top to bottom of the shaft. In the latter part of the year 1871, Mr. H. Murray & Son contracted with the company for the continuation of the work at the rate of four hundred dollars per yard in depth, to a point 100 feet below the Hillman seam of coal; for the succeeding 100 feet the price to be increased twenty-five dollars per yard, and so on until the bottom rock of the Baltimore seam of coal was found. The size of the shaft within the cribbing timbers is 45 feet 4 inches by 11 feet 6 inches, having six divisions of equal dimensions, 7 feet by 11 feet 6 inches, giving room for what is known as the "standard diamond " car, whose capacity when level full is 100 cubic feet, but when loaded by the miner 4 inches above the top contains 112 cubic feet." Two divisions of this shaft are intended for hoisting coal from the Hillman seam, two from the Baltimore seam, one for ventilation, and one for pumps. The works were planned for two pairs of direct-acting, high-pressure engines, twenty-four boilers, and for an estimated output of 2500 tons of coal per day from the two seams.

By V. F. STANLEY

THERE is not the slightest doubt that the present recoveries of valuable minerals by the Broken Hill mills could be improved, and that further machinery would be installed for the purpose if it could be assured that a high price of metals would be maintained; but concentration, like all other com¬mercial propositions, is a question of profit and loss, and no sensible metallurgist would carry out his work in such a manner as to obtain high recoveries at a financial loss to his company. There is a point in all concentration at which the added money obtained from the higher recovery of minerals is balanced by the extra cost of obtaining the last part of the recovery; a wise metallurgist will be content with his work before his working-expenditure reaches this point. To a casual observer, the work being done by the various Broken Hill mills is identically the same. A closer investigation will show that this is far from being the case, for it is a remarkable fact that, although the larger mines extend over a length of approximately only 2 miles, such a difference in the physical and chemical properties of the ores exists that, from the first reduction downwards, special treatment is necessary in each case, and hardly any two mills are identical in operation. The details of this paper refer directly- to the work of one . particular mill in Broken Hill, for the reason that the ore from each mine presents special difficulties and requires its own special treatment. I have selected the mill referred to because it has been constructed and modified under my supervision.

Sep 1, 1909

By E. M. Chance

HERBERT M. WILSON, Pittsburgh, Pa. (written discussion).-Permit me to endorse the author&apos;s conclusions and their form of presentation as ,being, in my judgment, the last word &apos;on the subject of lights for the illumination of coal mines. I also feel that the open-flame oil lamp has outlived its usefulness, and that it should go, in the interests not only of safety but of efficiency. Where an open-flame lamp can be used with safety in non-gaseous mines, the acetylene light adds materially to efficiency by its better illumination, and to safety for the numerous reasons given by Mr. Chance. The latter, however, lays chief stress on the value of the acetylene because of its non-fouling and non-obscuring effect on the atmosphere. Another important advantage over any other form of illumination is the clear, bright light projected at the point where the workman may look for danger. The better illumination materially safeguards the worker against obstacles over which he may stumble when traveling, and against dangers from falls of roof or of coal, weakness in timbering, and similar conditions. The acetylene lamp, where it may be used with safety, has advantages even over the present electric cap lamp, in that it gives a higher luminosity; and when the miner comes to learn its signals, as he will in time, just as he learns those given by the open-flame or the safety lamp, he will find that the acetylene lamp is a fair detector not only of methane but of carbon dioxide, as clearly shown by Mr. Chance. The only, serious objection, raised against the use of carbide lamps. has been recently in Pennsylvania, due to the belief of the State Mine Inspection Department that it endangered miners working on pillar work, or other places where carbon dioxide might accumulate, or where there is lack of sufficient ventilation, and because it was believed that the indications of the carbide lamp would not give the miner sufficient warning. On this point Mr. Chance has clearly shown the fallacies of the objections. I may add that for those unable to detect carbon dioxide with the acetylene lamp, the maximum of protection would be afforded by using an open oil lamp or a flame safety lamp in such places; or, because the miner might not watch his oil light, a better, protection still would be offered by a sufficient number of daily inspections of such working places by a fire boss or other official, with flame safety lamp.

Jan 4, 1917