Search Documents

By A. J. Rigby

Current practices employing porous plugs to inject nitrogen into molten copper during primary smelting are described. Nitrogen stirring increases heat transfer to the bath, eliminates temperature stratifications, and improves efficiency during the steps of desulfurization and deoxidation. The opportunity to use porous plugs as the means to introduce reducing gases to deoxidize copper is also discussed. Previously reported laboratory results using porous plugs, which point to very high utilization efficiencies of hydrogen when used as the reducing gas, are again reviewed. Advances in the design of the porous plug, and the introduction of a system enabling external replacement of plugs is also discussed.

Jan 1, 1999

By A. V. Tarasov

In order to improve the efficiency of hydrometallurgical processing of pyrrhotite concentrates, an integrated set of research has been carried out to investigate the use of sulfur dioxide in individual unit operations and as a leaching agent in the autoclave process as a substitute for oxygen. Treating iron-containing raw materials for production of nonferrous metals are based on the selective reaction of SO2 with iron sulfides and oxides. Iron is dissolved as sulfate, which can be treated in a separate circuit to produce iron-containing pigments or it can be disposed of after neutralization. Nonferrous and precious metals contained in pyrrhotite concentrate do not react with sulfur dioxide and remain virtually completely in the solid phase, i.e. high-grade sulfide concentrate to be treated by hydro- or pyrometallurgical methods. Elemental sulfur formed in the process of leaching is separated from the pulp in granulated form as a result of the use of special surfactants. The process of sulfide concentrate leaching with the use of sulfur dioxide is conducted at temperatures above the sulfur melting point (119°C) with distributed feeding of surfactant and under a partial pressure of sulfur dioxide of up to 0.3 to 0.5 MPa.

Jan 1, 2006

By B. J. Beaudry

The preparation of alloys containing one to two percent of the volatile lanthanide metals Sm, Eu, Tm and Yb in the high melting point (HMP) rare earth metals Sc, Y and Lu was accomplished by a vapor deposition, diffusion method without crucible contamination. The method avoids the melting of the HMP metals which would introduce impurities from the crucible, generally Ta or W. Plates of the HMP metals were hung from the lid in the upper part of the Ta crucible. The volatile metals were placed on the bottom and the lid welded in place under an atmosphere of helium. By proper selection of thee alloying temperature, the effusion of the metal vapors, through the helium atmosphere was slow enough to permit diffusion to occur and prevent refluxing of the newly formed alloy. Very volatile metals such as Mg required a Knudsen cell with a suitably sized hole to prevent too rapid transfer of the low melting metal. Electron microprobe analysis of a cross-section of the HMP metals showed a homogeneous distribution of the volatile metals. The time and temperature required to obtain a homogeneous rare earth alloy without contamination are given. The use of a Knudsen cell to form magnesium-rare earth alloys is reviewed.

Jan 1, 1992

By Biserka Lucheva, Tzonio Tzonev

"Recycling of aluminum scrap and dross is significant in the economic and energy saving, as well as in the environmental protection. Recovery of metal aluminum depends on many factors. The aim of this work is to investigate experimentally the metal recovery under different conditions. The processing of aluminum dross was carried out in DC electric arc rotary furnace. The optimal technological parameters are determined. It is turned out that the presence of crushing refractory bodies during the processing of the aluminum dross in the rotary furnace increases the degree of aluminum recovery with about 10 %.IntroductionCompact and granular aluminum dross are used for the fulfillment of the experiments, which were obtained by salt free melting of aluminum scrap. The only preliminary preparation of the compact dross is crushing them into proper size, in compliance with the size of the opening for furnace charging and removing of fraction – 1 mm. The granular dross is subjected to sieving also with the purpose to remove the fraction – 1 mm. In these conditions the content of the metal phase in the compact dross is 72 %, and in the granular – 77 %. The processing of aluminum dross was carried out in DC electric arc rotary furnace (Figure 1).The purpose of this research is to investigate experimentally the metal recovery under different conditions and to establish the dominant factors, which need to be controlled."

Jan 1, 2008

By Laurentiu Nastac

"This paper describes the development and validation of a comprehensive multiscale modeling approach capable of predicting at the mesoscopic scale level the ingot solidification structure and solidification-related defects commonly occurring during the vacuum arc remelting (VAR) process. The approach consists of a coupling between a fully transient macroscopic code and a mesoscopic solidification structure code. The predictions from the multiscale model, including grain morphology and size, primary and secondary dendrite arm spacings, Laves and NbC phases, tendency for freckling and columnar-to-equiaxed transition, were validated against experimental measurements for a 20-inch diameter VAR alloy 718 ingots. The validated model was then used to investigate the effects of melting rate and ingot diameter on the solidification structure of VAR processed 718 ingots.IntroductionThe objective of this work was to develop a fully transient multiscale modeling approach to get an insight into the effect of processing parameters on the cast micro- and macro-structure during VAR processing. The developed model assists in achieving better control of the ingot solidification structure and to determine trends in the macrosegregation in these ingots. Another objective of this work was to analyze the transient effects of production rate and ingot size on the resultant ingot microstructures. This objective was met by first understanding the effects of the full range of processing parameters typically used in the VAR process. Processing parameters such as power input and heat extraction rate significantly influence the ingot liquid pool size and shape as well as the ingot structure, which in turn will greatly impacts the final ingot quality."

Jan 1, 2012

By Ivanildo Hespanhol

"DALYs are a measure of the health of a population or burden of disease due to a specific disease or risk factor. It evaluates the time lost because of disability or death from diseases compared with a long life free of disability in the absence of disease. DALYs are calculated as the sum of years of life lost by premature mortality (YLL) and years of healthy life lost in states of less than fully health, i.e., years lived with a disability (YDL), which are standardized by means of severity weights, thus: DALY=YLL+YLD.WHO has established for wastewater use in irrigation (1) the same reference level of health protection as established for drinking water quality (2), i.e., the additional burden of disease from consuming water irrigated food should not exceed 10-6 DALY(Disability-Adjusted Life Years) loss per person per year (pppy). This level of risk means that a single additional case of disease may occur in a population of 1 million, during a life time (70 years). In a individual basis is equivalent to the occurrence of a mild disease during about 31,5 seconds.Such a restrictive risk is almost impossible to be attained in most developing countries which may not be able to afford the cost of wastewater treatment and of other protective measures, even for restrict irrigation.This paper presents proposals to adapt the reference level of risk to local technical, cultural, economical and social conditions of developing countries on the basis of a risk benefit approach."

Jan 1, 2008

By J. M. Tourre

1995 have seen a continuation of a positive trend in the Rare Earth industry The availability of a greater diversity of Raw Material has brought additional flexibility to the Producers permitting better economics China remains the major raw material source; Chinese concentrate producers have increased capacity in 1995 (Baotou, Sichuan, etc) China's role in the Rare Earth industry will continue to evolve; the acquisition of a majority equity position by San Huan/CNNC will have a significant impact on both the Rare Earth and Magnet markets Chinese producers are increasing the quality of their products and realize their true values Chinese market, itself, is also changing as the internal needs for separated rare earth's grow Already already producer of Lamps, Loudspeakers, Magnets, and TV tubes, China is in an unique position where the potential of its internal market might be more promising than the prospects outside China 1995 has also seen the application market become more diverse and complex. There are new applications growing at a very strong pace (such as battery alloy), applications that are now penetrating their target markets with significantly increased growth rates (such as bonded NdFeB), and some applications that became more complex requiring much more sophisticated products (such as catalysis). Rare Earth producers have to spend significant ressources in order to monitor the market trends in order to predict the demand and then adjust their raw material mix. Even though there is a greater diversity of raw material available, there is still some Rare Earth elements that are in excess, while other are just in balance. As a consequence rare earth producers invest heavily in R&D in order to develop new applications for these excess elements.

Jan 1, 1997

By Xiangru Chen, Qijie Zhai, Haicheng Li, Chao Yang, Zhang Wei

The Nb-rich phase generated by the addition of trace amounts of Nb(<0.1wt%) \ and the effects of different content of Nb on the morphology and distribution of graphite in ductile iron were studied in this paper. The results showed that when the content of niobium less than 0.1wt%, the two-dimensional morphology of Nb-rich phase existed in microalloyed ductile iron were mainly regular pattern such as square, triangle, polygon etc. Besides, Nb-rich phase in large size distributed in the matrix with a certain distance from graphite. With the increasing amount of niobium, the dispersion degree of graphite diameter, average diameter and roundness increased slightly, and the number of graphite decreased slightly.

Jan 1, 2015

By I. Van de Voorde

In this paper, results are presented concerning the search to implement Supported Liquid Membranes (SLM) Technology for the recovery of copper, nickel and zinc from electroplating and other effluents to prevent metal waste. A study of the influence of the individual parameters and of their combined effect on mass transfer in small-scale laboratory equipment has been performed, enabling to set forward the appropiate operating conditions for a pilot plant installation. The SLM pilot plant has been tested extensively, including short and long term runs, with real process solutions. It was demonstrated that the SLM technolgy is applicable for solutions containing 800 mg/L of metal ions, but also to the treatment of solutions with low metal content of origin other than plating shops. It was demonstrated by system analysis that the recycled salts are usable to produce metal electrolytes (for example Watt&apos;s nickel bath).

Jan 1, 2003

By M. Hadj Meliani

This paper explores direct use of finite element analysis by CASTEM 2000 in order to determine the evolution of T-stress term for arc of pipe specimens with external surface crack. A simple method, called the stress difference method proposed by Yang (1999), is used to compute the elastic T-stress in mode I at a crack tip. The different crack geometries and length-to-thickness ratio on T-stress and stress-intensity factor (SIF) are examined. The revisited stress difference method is shown to be an accurate and robust scheme for evaluating T-stress in arc of pipe.

Jan 1, 2006

By Maurizio Marezio Bertini

Ammonia - ammonium sulfate solutions were sparged in a glass reactor with a SO2/O2 gas mixture (2% SO2 and 98% O2) to leach copper from pure chalcopyrite and chalcopyrite concentrate. The SO2/O2 mixture produces higher and faster extractions than O2 by itself. The effect of temperature, particle size and free ammonia concentration was investigated. The fastest and highest recoveries were obtained at 80 oC from a chalcopyrite concentrate with a d80equal to 13 m, with about 83 gpl free ammonia, an average pH equal to 8.75 and a stirring speed of 500 rpm. The extraction process was controlled by diffusion through a product layer, according to the shrinking core model, with an activation energy of 41 kJ/mole.

Jan 1, 2003

By C. H. Quan

Solvent extraction tests were carried out on a rare earth chloride solution derived from monazite processing to determine the effect of extractant and diluent on the distribution coefficients between organic and aqueous phases, and the separation factor between rare earths. The extractants were 20% by volume di-2-ethyl-hexyl phosphoric acid (DZEHPA) or 2-ethyl-hexyl phosphonic acid (Ionquest® 801). Four Shellsol diluents were tested ranging from nil to 100% aromatic content. D2EHPA gave the highest rare earth extraction for a given pH but was less selective than Ionquest. The geometric mean separation factor between adjacent rare earths varied from 2.41-2.56 for D2EHPA to 2.62-3.01 for Ionquest. The nil-aromatic diluents (Shellsol 2037 and 2358) gave better separation factors in Ionquest but, in D2EHPA, were slightly inferior to the 100% aromatic diluent Shellsol AB. Yttrium behaved as a pseudo-heavy rare earth with a distribution coefficient lying between Ho and Er, as expected from its ionic radius.

Jan 1, 1992

By Manolete Mena

WC-Co nanocomposite powder is among the first group of materials with a promising potential for nanocrystalline-materials application. A chemical vapor synthesis (CVS) process that has previously been used for preparing the aluminides of titanium and nickel, and other metallic and intermetallic powders has been applied to the preparation of WC-Co nanocomposite powder. This CVS system was designed so that a tungsten precursor (WCl6 powder) and a cobalt precursor (CoCl2 powder) were separately fed into each evaporator in a reactor by means of specially designed powder feeders. The reduction and carburization of the vaporized chlorides by methane-hydrogen mixtures produced nanosized WC and Co composite powder. The product is a very uniform mixture of the constituent powders, which is important to ensure a high quality of the bulk cemented tungsten carbide product after consolidation. In the present work, the effects of reaction temperature, CH4 to WCl6 ratio, CH4 to H2 ratio, residence time, and Co content on the powder composition and particle size were determined. The products were characterized using XRD, carbon analyzer, and TEM.

Jan 1, 2006

By Yuhua Pan

Generic mathematical models have been developed for simulating heat transfer in two types of slag resistance heating electric furnaces for sulphide smelting: i) six-electrode-in-line rectangular furnaces and ii) three-electrode circular furnaces. The models are based on three-dimensional steady-state heat transfer of conduction, convection and radiation. Solidification of liquid slag into solid slag by water-cooling units, for use as freeze lining of furnace walls, is also considered in the models. The developed models are capable of providing predictions with reasonable accuracy for electric furnaces on 1) temperatures in slag, matte, cooling water, freeze lining and other solid regions as well as temperatures at various fluid/solid interfaces, 2) freeze lining thickness, 3) furnace smelting rate and 4) furnace heat loss rate. These computer models are built into executable application programs that are very efficient, with execution time less than one second, and can be easily portable to most computing platforms. This paper describes, as an example, the modelling results on heat transfer in six-electrode furnaces. The major modelling results show that in six-electrode furnaces uniform electric power inputs to the electrodes likely lead to low temperature regions close to slag and matte tapping ends of the furnaces, and the power input and the formation of air gaps between freeze lining and cooling units have significant influences on the thickness of freeze lining maintained by the cooling units.

Jan 1, 2006

By V. T. Taniguchi

A process for large scale chromatographic separations using a continuous chromatography technique is described. The process combines the advantages of large scale batch fixed column displacement chromatography with conventional analytical or elution continuous annular chromatography (CAC) to enable large scale displacement chromatography to be performed on a continuous basis (CDC). Such large scale, continuous displacement chromatography separations have not been reported in the literature. The process is demonstrated with the ion exchange separation of a binary lanthanide (Nd/Pr) mixture. The process is, however, applicable to any displacement chromatography separation that can be performed using conventional batch, fixed column chromatography.

Jan 1, 1989

By Z. S. Wronski

In rapidly solidified Fe-Nd-B permanent magnet alloys, the content and distribution of Nd-rich intermetallic and Fe-phases determine coercivity Hc and remanence Br. Consequently, microstructure plays a crucial role in deter- mining the (BH) max-product of permanent magnets fabricated from these alloys. A study has been initiated to investigate changes in microstructure and the effects on magnetic properties as the material is processed from arc-melted ingot to melt-spun flakes and finally to a product consolidated by hot-forming. Anisotropic magnetization behaviour has been observed in rapidly solidified flakes after low-temperature annealing.

Jan 1, 1989

By P. Ruz

A melt transfer ladle was 3D modeled by means of a mathematical fluid dynamics and heat transfer program. Internal temperature profiles were calculated as a time function for a normal ladle and for a pre-heated refractory lined ladle. It was shown that in a normal ladle the molten metal cools down quickly forming accretions. By using an inner lining there are practically no accretions build up within a typical time of operation. Therefore, by applying a refractory lining to a melt transfer ladle and keeping it at a moderate to high temperature it is possible to reduce cold dope circulation in the smelter.

Jan 1, 1999

By Katsutoshi Komeya

Aluminum nitride(A1N) is a theoretically high thermal conductive ceramic, but is a poor sinterable one because of its covalent bond structure. The densification of A1N had to be done first. It was found in 1968 that rare earth compounds as yttria were an excellent sintering aids. Recently more improvement of conductivity was attained by following effects of yttria: (1) trapping of oxygen in A1N sources to form yttrium aluminates, (2)elimination of the aluminates by heating in carbo-reductive atmosphere. Consequently very high thermal conductivity of up to 270W/mK has been developed. Thus A1N applications for substrates and packages have been opened.

Jan 1, 1992

By Wen-Ming Chien

Low temperature X-ray diffraction and thermal property studies of the solid-solid state phase transition for the polyalcohols (pentaerythritol (PE), pentaglycerine (PG) and neopentylglycol (NPG)) thermal energy storage solid solutions have been investigated by using X-ray diffractometry and differential scanning calorimetry (DSC) methods. X-ray diffraction studies on polyalcohols solid solutions, PE-NPG and PG-NPG, are from ?10oC to 50oC. XRD results shows the + mixed phase at the related low temperature (?10oC) for both PE-NPG and PG-NPG solid solutions. At high temperature range, XRD results show phase for PG-NPG solid solution and + mixed phase for PE-NPG solid solution. There are only two Bragg peaks, (111) and (200), shown in phase XRD patterns. The polyalcohols solid solutions have been cycled 5 times between -20oC to 100oC at different DSC scan rates to study the phase transition properties. DSC results of both PE-NPG and PG-NPG solid solutions show that the solid-solid state phase transition is near room temperature. Details of low temperature phase transition XRD and DSC results of PE-NPG and PG-NPG solid solutions will be presented

Jan 1, 2006

By G. Achurra

The products of the smelting of copper concentrates in an El Teniente Converter (CT) are a high grade matte, analyzing 74-76% Cu; and a highly oxidized slag, typically containing 15-20% Fe3O4 and 4-10% Cu. The El Teniente Division of CODELCO¬CHILE has developed a slag reduction-cleaning process, that is practised in a tilting, horizontal furnace, to recover copper from these slags. The El Teniente slag cleaning process has been successfully implemented at the El Teniente Caletones smelter and various other smelters in Chile: Today, eight such slag cleaning furnaces, each with a capacity of 800-1000 tonnes/day, are in operation in Chile. This paper discusses basic laboratory research and industrial tests that led to substantial reductions in the slag cleaning cycle time and the specific consumption of fuel and reductants. Simultaneously, the slag cleaning off-gas quality was improved. Based on the experimental results, recommendations were made to improve the practice of the El Teniente slag cleaning process. The recommended modifications have been fully implemented at the Caletones smelter.

Jan 1, 1999