Search Documents

By Shadia J. Ikhmayies

Polycrystalline CdTe thin films were prepared by vacuum evaporation on glass substrates. The I-V plots which were linear were used to find the resistivity. A value of 2.10×106 .cm was obtained. The transmittance was measured in the wavelength range 400-1100 nm. The bandgap energy was found to be 1.48 eV. X-ray diffraction pattern shows that the material deposits in the zinc blend structure with one strong reflection from the C(111) plane. The scanning electron microscope image shows a uniform surface with a small density of large (mµ1£) grains scattered on the surface.

Jan 1, 2009

By Lisa E. Helberg

"Titanium tetrachloride is produced through the chlorination of a variety of titanium bearing ores, some occurring in nature, and others enriched in titanium content by a variety of ""beneficiation"" processes. The chlorination step can produce a variety of metal chloride impurities, such as iron chlorides and vanadium chlorides, which must be removed from the TiC14 before it can be used to produce pigmentary TiO2, titanium metal or for any other commercial use. The requisite manipulations involve both physical and chemical separations in a multi-step process. The history of various purification strategies will be discussed.TextThere are a wide range of titanium-based products available, all of which start with titanoferrous ore of some type. Two main routes are used to convert ores into products, known as the sulfate and chloride processes. The sulfate process uses sulfuric acid to digest the ore, separate the impurities, and then precipitate titanium dioxide from the resulting titanyl sulfate (TiOSO4) via metatitanic acid. This process can also supply TiOS04 for other applications."

Jan 1, 2011

By P. Hajiani

Rare earth elements (REEs) are critical materials in many leading-edge technology products. However, REE separation outside China has remained a challenge in addressing environmental concerns of current production. The author has worked on a technique employing the emphasised variability in the electrophoretic mobility (μi) of REE for the purpose of REE separation. In continuation of the results presented in IMPC 2016 [1], this contribution summarizes the progress achieved in 2016 and 2017. The major goal was to increase the REEs concentration by a factor of 1000 and to attenuate the consequent drawbacks, specifically joule heating effect. Amphiprotic hydroxylic solvent was selected to replace water, which has a major impact on the complexation mechanism and buffer requirement. Non-aqueous media result in a significant drop in the specific molar conductivity of the electrolyte, whilst μi reduces several times only. Moreover, a quasi-steady state electrophoretic separation in conjunction with temperature gradient focusing is adapted to improve scalability.

By Xi Dai

The LiFe1-xNixPO4(x=0, 0.05, 0.10) cathode materials for Li-ion battery were synthesized with Fe1xNixC2O4?2H2O(x=0, 0.05, 0.10) as Fe sources by high temperature solid-state reaction method. The Fe1xNixC2O4?2H2O(x=0, 0.05, 0.10) materials were produced by liquid co-precipitation method and crystal structure and morphology of cathode materials were characterized by X-ray diffraction and scanning electron microscopy. The composition contents and charge-discharge performances were measured by chemistry analysis and charge-discharge apparatus. The XRD patterns showed that LiFe1-xNixPO4(x=0, 0.05, 0.10) cathode material samples were well-crystallized homogeneous olivine-type phase, with only tiny trivalent iron impurities according to chemistry analysis results. Charge-discharge test showed that cathode materials possessed excellent charge/discharge capacities, about 150mAh/g at 0.1C rate and more than 120mAh/g at 0.4C rate. The polarization of cathode in charge-discharge process can be restrained effectively, for the potential offset between oxidative peak and reductive peak of doped LiFePO4 material was only 0.079V, lower than pure LiFePO4 markedly.

Jan 1, 2006

By J. E. Klein

Bench scale tests using a stack of ten whole SAES St909 pellets, 6 grams, to crack methane have been completed with pure methane feed. Test conditions ranged from 600 to 800°C at 101 kPa (760 ton) with a methane feed rate of ten sccm. Methane reformation tests, test where hydrogen was passed through a St909 bed after cracking methane, were performed to determine if and how much methane can be generated under "reformation" conditions. Phase structure determinations of St909, composed of a ZrMnFe alloy with aluminum used as a pellet binder, after methane cracking were complicated by the number of materials that can be formed by the elements in the St909 and the carbon from methane cracking. It was determined that the aluminum not only alloys with the Zr, Mn, and Fe in the St909 alloy, but also forms aluminum transition metal carbides in addition to ZrC as the carbon content and the temperature of the St909 increases. Some A14C3 was also found in some pellets. Passing hydrogen over St909 pellets after methane cracking formed methane at various rates in the temperature range of 600 to 800°C. Temperatures of 800°C gave the best methane cracking performance and efficiencies decreased rapidly with temperature.

Jan 1, 2002

By Shadia J. Ikhmayies

CdSxTe1-x and CdS1-yTey solid solutions are usually formed in the interfacial region in the CdS/CdT thin film solar cells during the deposition of the CdTe layer and/or the processing steps of the device. It is well known that CdCl2 heat treatment encourages the formation of the CdSxTe1-x alloy which improves the solar cell performance. In this work, indium doped CdS1- yTey thin films are produced by first producing CdS:In thin films by the spray pyrolysis (SP) technique on glass substrates, then annealing the films in nitrogen atmosphere in the presence of elemental tellurium. The films are characterized by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), and transmittance measurements. The transmittance is used to deduce the optical parameters such as; the extinction coefficient, refractive index, besides to the real and imaginary parts of the dielectric constant. The dispersion parameters such as Eo (single-oscillator energy) and Ed (dispersive energy) of the deposited films are also estimated and discussed.

Jan 1, 2015

By B. Q. Li, S. P. Song

"This paper describes an on-going research on developing coupled boundary element and finite element algorithms for the solution of thermal and electrodynamic problems relating to materials processing. The coupled methods are uniquely suitable for field problems involving composite regions, in which detailed information on field distributions within one particular region is of more interest and yet the solution can be obtained only if the effects of other regions are all considered. Problems of this type include heat transfer in multiple regions and also magnetic induction involving an infinite boundary. The hybrid boundary and finite element formulation, algorithm development and the applications are discussed. Two examples are given to demonstrate the capability and accuracy of the coupled algorithm for heat transfer problems. Various treatments of corner discontinuity are discussed. It is found that the double flux treatment is an ideal choice amongst those tested as it is easy to implement and also gives the most accurate solution. 1. INTRODUCTIONElectrodynamic and transport problems occur frequently in materials processing systems. Accurate solution of these problems is of great importance not only for our fundamental understanding of physical principles governing these phenomena in the processing systems but also for optimization of the existing processes as well as development of new processes. For this purpose, many numerical algorithms have been developed. These computational schemes in general can be classified into three categories, that is, the finite element and finite difference schemes and the boundary element scheme. The former two are domain based numerical algorithms while the latter the boundary-based algorithm.The finite element method, which is based on the variational calculus, is a very useful and yet popular engineering numerical method for boundary value problems defined over irregular boundaries. The use of the method requires the discretization of the entire domain. It can be applied to solve both linear and nonlinear problems, but is particularly powerful for nonlinear problems that involve the field variables defined within the computational domain. On the other hand, the boundary element method, with its root in the Green's function method, is very efficient for linear boundary value problems or nonlinear problems that involve field variables only along the boundaries. The primary advantage of the boundary element method lies in the fact that only the boundaries of the computational domain need to be discretized, and hence the dimension of the problem is reduced by one, compared with the finite element method."

Jan 1, 1994

By G. Upadhya

Of late, solidification modeling has progressed considerably to emerge as a viable simulation tool for the foundry engineer. A wide variety of tools exist in the commercial market to cater to the various needs of the design/ foundry engineer. In fact, recent developments in the area of solidification modeling have been so rapid that a comprehensive review of the state-of-the-art is very much needed. In this paper, an attempt is made to summarize the various issues of solidification modeling, at the same time addressing the historical evolution of the subject. The various phenomenological issues covered in this paper include: heat transfer, fluid flow during mold-filling, solidification kinetics and microstructural evolution, quick-analysis schemes for approximations, porosity prediction models, and the phenomena of fluid flow in the mushy zone. Modeling issues related to the development of solidification stresses which lead to defects such as hot tears and the development of artificial intelligence concepts in the area of rigging design are also discussed. Due emphasis is given to the various phenomena which add to the complexity of the whole subject, and the various alternatives available for solving a particular problem. For example, the heat transfer problem can be approached by the use of simple modulus schemes or by solving the conduction equation to obtain a more accurate temperature distribution. Similarly the microstructural evolution can be handled in a deterministic way by use of nucleation and growth models, or in a probabilistic way by use of empirical models. The main goal of this paper is to put the multi-faceted problem of solidification modeling in proper perspective so that it can serve as a guide for future developments in this area.

Jan 1, 1994

By Michael B. Tessieri

With the increasing environmental demands and higher fuel efficiency standards on auto manufacturers, the use of aluminum in automotive applications is expected to show significant growth for the balance of this decade. Cast and wrought aluminum usage is reviewed by auto part, and alloy family for the year 2000 automobile. The analysis addresses the effect of this increased volume on the recycling infrastructure and identifies issues and opportunities, which will face the recycling industry.

Jan 1, 1995

By David Bequette, Ray D. Peterson, Cynthia K. Belt

"With a need to cut production costs in the metals industry, cost savings from energy efficiency improvements are critical. Opportunities can be found by reviewing furnace systems and practices so that the melting and holding processes operate at the highest energy efficiency. Many of the changes can be implemented with a minimum of expense or capital investment. This paper will review several low cost methods to optimize energy efficiency on reverberatory melting or holding furnaces. These five methods (furnace utilization, idle procedures, fire rate, controls, furnace pressure) will be explained and information given to implement these changes. Included are several rules-of-thumb and benchmarks for aluminum reverb furnaces.IntroductionEnergy can be a significant portion of the total manufacturing costs for metals and materials manufacturing involving thermal processing such as heat treating, melting, and high temperature processing. Natural gas prices have dramatically varied over the last few years. While no one can foresee the future, prices are expected to increase from the current low prices. More recently, emphasis is being put on the reduction of greenhouse gases with the potential of additional costs to industry.One of the first steps in an energy management program is to measure the energy usage of the process [1]. The results are typically understood in relation to the mass melted in kWh / mT [BTU / lb]. For the purposes of this paper, furnace energy efficiency is calculated over a month or even a year and thus includes hold times. This efficiency is typically different from the values quoted by furnace manufacturers. Those values are for limited short term tests at highutilization.Once you know the performance for your furnaces, these should be compared to industry benchmarks. For aluminum melt furnaces with cold air burner systems, a benchmark value or goal is 1800-2000 BTU/lb [1160-1290 kWh/mt], though some of the best have reached 1600 BTU/lb [1030 kWh/mt]. Furnaces with regenerative burners can attain 1100-1200 BTU/lb [710- 775 kWh/mt]. There are some designs of multi-chamber furnaces or oxygen furnaces that have improved on these numbers, perhaps as low as 950 BTU/lb [615 kWh/mt]. Typically, as the degree of sophistication and energy efficiency of the furnace increases, so does the cost."

Jan 1, 2010

By Irshad A. Rana

In a modern copper smelter, the capital cost of a sulfuric acid plant constitutes the largest single cost item of the total investment. It is thus essential to properly size the acid plant in order to reduce its capital cost and enhance the economic viability of a new smelter project. Whereas the off-gas from a smelting furnace is continuous and generally uniform, the gas flow from the Peirce-Smith converters is intermittent with significant fluctuations. The converters off-gas volume is dependent upon a number of interrelating factors. The most significant factors are the matte feed grade, the system air infiltration, the converter's size and blowing rate, the maximum number of converters simultaneously blowing and the gas cooling system employed. The acid plant size, therefore, is heavily influenced by the converter off-gases. Several of these factors are discussed, and their impact in determining the acid plant size is explored.

Jan 1, 1993

By Ma Shao Xian, Li Dong, Li Zhen Guo

"The new type shaft calciner ( SK-10 Serials) is developed and designed by CADRE itself on the basis of the conventional shaft calciner. The actual application in a number of calcinations plants have proven that they are of very good effect. Calcined coke calcining heated by the shaft calciner has a high quality, lower lost by fire. The shaft calciner needs no additional fuel when it is working. Anode Carbon Plant and calcined coke Plant commonly used the shaft calciner in domestic. The waste heat from the shaft calciner can be recuperated to generate electricity and to make the steam for produce. Exhaust waste heat is recovered by 90% or more. The new type shaft calciner's structure is optimized by computer simulation for fire-wall structure, combustion air to fuel ratio, volatile combustion is fully in use, furnace cooling zone structure, the exhaust smoking structure and calciner heat balance. Furnace structure and production operating parameters has been got the best optimized results. This paper introduces the working principle and characteristics of the shaft calciner - the equipment for calcining of the petroleum coke. It also demonstrates measured process parameters of the new type shaft calciner. Through comparison with the rotary kiln and conventional shaft calciner, it proves its own technical characteristics and advantages: higher capacity, high quality products, provides more energy for power generation, equipment operation and maintenance costs lower.IntroductionChina's petroleum coke market is mainly dominated by the delay raw petroleum coke. Rotary kiln and shaft calciner are the main process equipment for calcined petroleum coke. As the shaft calciner burning less, no external fuel, waste heat utilization is high, long service life, the utilization rate in China is more extensive than the rotary kiln."

Jan 1, 2012

By Dan Michaelsen, Warwick Stewart

"PT Kaltim Prima Coal (KPC) is a large-scale truck and shovel operation mining thermal-coal in East Kalimantan, Indonesia. The operation produces 15 million tonnes of coal and mines over 120 million bank cubic metres of overburden annually. Approximately 35 percent of the waste rock is classified as potentially acid forming. Acid drainage must therefore be managed to prevent acid formation from spoil dumps and mined-out areas.KPC aims to prevent acid production in dumps by covering potentially acid forming spoils with materials identified as non acid-forming. The covers, built to engineering standards, minimise the flux of oxygen and water to pyritic spoils, thereby controlling the oxidation reaction, and reducing ARD discharge to negligible rates. Cover designs and cover materials vary according to stability, materials availability, equipment availability, and cost effectiveness. A modified field net acid generation (NAG) test procedure has been developed at KPC to identify and segregate overburden geochemical types. This paper discusses the ARD management strategies and operational procedures adopted by KPC to manage potentially acid forming waste rock. The development and field application of the NAG procedure at KPC is presented in a companion paper. Analytical"

Jan 1, 1999

By M. Krishna, Jayagopal Uchi1, Shanta Sastry, B. M. Satish

"A well-considered composite of ZA-27 reinforced with weight percentage 0, 2, 4, and 6% of alwninite particulate has been made by compocasting technique. The elastic properties of ZA- 27 /alwniniute particulate composite were determined by using U1M. The results showed that the modulus of elasticity and UTS of the composite gradually increases with increase in the wt.% of reinforcement. However, the overall ductility decreased monotonically with an increase in reinforcement. The results of these tests· as well as the predictions of several model~ for composite strengthening available in the literature were compared with experimental results. The data observed from Young's modulus by measurements studies were compared with theoretical results predicted by Eshelby model.IntroductionMetal matrix composites (MMCs) have received increasing attention in _the recent decades as engineering materials. The introduction of a ceramic reinforcement into a metal matrix produces a composite material resulting in an attractive combination of physical and mechanical properties that cannot be obtained with monolithic alloys. Particulate reinf9rced MMCs among the discontinuously reinforced MMCs have attracted quite a lot of attention both in the industrial sectors and the academic communities. There is an increasing need for knowledge about the processing techniques and mechanical behavior of particulate MMCs in view of their production getting enhanced and their commercial applications becoming wider [I]. Interest in particulate reinforced MMCs is mainly due to easy availability of particles and economical processing techniqu"

Jan 1, 2000

By Baokuan Li, Fang Wang

"Comparing with the single electrode in electroslag remelting processes, two series-connected electrodes have the advantage of little inductance, lower power consumption and higher melting rate, which was widely used to produce superalloys and specialty steels. Detailed understanding of the electromagnetic field distribution is essential for both improving ingot quality and saving electric energy. In the present work, a 3D finite element model was developed for the magnetic field, electromagnetic force, current density and Joule heating field of electro slag remelting processes (electrode, slag and ingot) with two series-connected electrodes using Maxwell equation, Lorentz law and Joule law. The results show that the maximum current distribute occur at the middle of electrode, due to the interaction of selfinduced and mutual-induced of two series-connected electrode; associated magnetic flux density on the inner side of electrode increase and the outer decrease; The maximum joule heating is at the interface of slag and electrode. The parameter study shows that if the current frequency is greater than 35Hz, the current density in inner electrode tend to linear distribution; with the increasing of original current, The maximum current density near the wall in electrode will increase linearly; with the increasing of electrode innnersion depth and decrease of slag cap thickness and the maximum of the joule heat in slag will increase.IntroductionElectroslag remelting processes(ESR) are widely used to produce superalloys and specialty steels [l-3l_Two pair, four pair or six pair electrodes in electroslag remelting processes is common in casting large scale ingot, which has the advantage of little inductance, lower power consumption and higher melting rate, comparing to singe electrode. They have the same essence with two electrodes in ESR.Compared to the single electrode ofESR, the other electrode is added which can decrease the reactive resistance and power consumption in the two electrodes of ESR. It is a complicated metallurgy process with a series physical and chemistry phenomenon from the molten of steel to the solidification of ingot [4-71_ These physical and chemistry phenomenon originated the effect of alternating current of high intensity. The rule of the alternating current of high intensity which revealed the law of physical and chemistry phenomenon in ESR is the precondition of improving ingot quality and saving electric energy. Jihe Wei and Yongli Ren[S-9lstudied the distribution of electromagnetic field in single electrode ofESR with Maxwell equation and relative electromagnetic theory. It had the limitation that take the electrode and mold as infinite conductivity. A detail analysis of Electromagnetic fields in ESR had been conducted by Patel A D [JO-llJ using general stream-function formulation. It is difficult to extend to three dimensions which could not be used widely. Daniel V [lZJ and Kharicha A [BJ only analysis the current density associated magnetic flux density field and temperature field without the whole irlformation of electromagnetic field. Maopeng Geng [l4J considered the current density and temperature field of the real and fake electrodes in ESR without skin effect. As to the complication of the two electrodes of ESR, it is rarely reported the electromagnetic field and Joule heating field of the two electrodes in ESR. The rule of effect of electromagnetic and modification of numerical simulation should be studied in depth."

Jan 1, 2011

By Carlos Maurício. F. Vieira, Lázaro A. Rohen, Sérgio N. Monteiro, Rafael G. de Castro, Gustavo X. Borges, Maycon A. Gomes, Frederico M. Margem, Anna C. C. Neves

Economic and environmental benefits are motivating studies on natural fibers, especially lignocellulosic extracted from plants, have been studied to substitute synthetic fibers, such as glass fiber as reinforcement in polymer matrices. By contrast to synthetic fibers, natural fibers have the disadvantage of being heterogeneous in their dimensions specially the diameter. About the hemp fiber, little is known of their dimensional characteristics. The aim of the present work was to statistically characterize the distribution of the diameter of hemp fibers. Based on this characterization, diameter intervals were set and the dependence of the tensile strength of theses fibers with a corresponding diameter was analyzed by the Weibull method. The diameter was measured with precision using a profile projector. Tensile tests were conducted on each fiber obtain mechanical strength. The results interpreted by Weibull statistical showed a correlation between the resistances of the fiber to its diameter.

Jan 1, 2015

By M. Waladan

The top submerged lancing Sirosmelt system has been developed through laborator.y scale testwork and pilot plant trials for recovery of zinc from ISF slag. The effects of the process variables of gas injection rate, method of coal feeding, and temperature on zinc fuming rates were studied in the laboratory. It was found that the rate of zinc elimination was dependent on all of these variabl.es. The rate of zinc removal from slag was independent of zinc content of slag down to approximately 1.5% Zn, below which the rate was proportional to zinc content in slag. Pilot plant trials were carried out to evaluate a proposed process and results followed predictions from the laboratory scale tests. A comparison of the proposed process with conventional slag fuming operations is made and it is shown that the process has a number of advantages which have a significant impact on the economics of zinc slag fuming.

Jan 1, 1990

By Maria D. Salazar-Villalpando, Anthony Cugini, Bryan Reyes

"The electrochemical reduction of CO2 was performed in a laboratory-made, divided Htype cell. A copper electrode was used as the cathode. An Aldrich Nafion 117-type ion exchange membrane (0.18mm thickness) was used as the diaphragm. NaHCO3 and KHCO3 were studied as the catholytes. Hydrogen evolution from water reduction and products from CO2 electrochemical conversion were recorded. Higher CO2 reduction enhancement was observed by KHCO3 as compared to NaHCO3. The main conclusion of this work is that in fact CO2 can be electrochemically reduced with copper electrodes.1.-INTRODUCTIONThe direct electrochemical reduction of CO2 may allow for a simple process and, by avoiding high temperature reactors, would enable the process production rate to be quickly varied to follow the time of day availability of surplus electricity [1]. Temperature has a major effect on the electrochemical conversion of CO2 since its solubility increases when temperature decreases [2]. The electrical potential applied to the electrochemical reacting system will have an influence on the product distribution, as well. For example, a narrow potential range during cyclo-voltagraphic studies will determine the detection of a lower number of products. A recommended potential range to study the electrochemical reduction of CO2 is -2V to 2V. Moreover, the reaction rate on the electrode is governed by various processes, such as the kinetics of electron transfer, adsorption/desorption at the electrode surface, and diffusion of CO2 to the Cu electrode. The availability of active species, CO2 for electro-reduction, is extremely low at the vicinity of the electrode surface and it seriously interferes with the rate of mass transfer. In batch type electrolytic reactors, depletion of CO2 at the surface takes place first. CO2 from the bulk then has to diffuse to the electrode surface, resulting in mass transfer controlled kinetic phenomena. During the above process, several other competitive side reactions could suppress the primary reaction even though the cathode has good electro catalytic properties for reduction of carbon dioxide. When the dynamic supply of specific active species is ensured to electrode surface, the mass transfer effects are minimized to certain extent. Hence it is envisaged that a continuous flow reactor is more efficient for the electro-reduction of CO2 in CO2 saturated aqueous electrolytes. The primary reactions that occur at the copper electrode during the reduction of CO2 are listed below (with the standard potentials calculated using formation energies [1] :"

Jan 1, 2010

By S. K. Utimurd, D. C. R. Espinosa, J. A. S. Tenório

"Waste Electrical and Electronic Equipment (WEEE) has become an environmental issue due to technological advance and waste plastic is one of the main polluters. The excessive discard of these plastics result in a difficult to dispose it to landfill and need further separation with technique in order to produce high added value plastics. There are many kinds of plastics in extensive use at the present time and the co=on are the acrylonitrile-butadiene-styrene (ABS) and high impact polystyrene (HIPS) used in the production of electric appliances. These plastics are difficult to separate because they have similar densities. Flotation of plastics is one possible separation technique and using selective wetting agents. The separation may be possible given close control at particle size and the concentration of the reagent. The process was able to produce a concentrate of HIPS with at least of 93% purity and a concentrate of ABS with 99% purity.IntroductionThe current situation of municipal solid waste (MSW) management especially in emerging economies like Brazil, the growing population and economic activity will result in a significant increase in the generation of waste in the coming decades. It is worthwhile to review and update the sources, amounts and recovery technologies of specific materials from waste, particularly from municipal solid waste (MSW).The growing impact of the current waste management practices stresses the need for a change in how waste is handled. The 2012 survey and the Brazilian Association of Public Cleaning and Special Waste Disposal Companies (ABRELPE) reports the generation of 62 Mt urban MSW in that year, which is an increase of 13% compared to 2011. It has been reported that in Brazil about 90.17% of the generated MSW is currently collected, which indicates an increase in the coverage of collection services compared to 2011 [ l]."

Jan 1, 2014

By Manju Gurung, Birendra Babu Adhikari, Keisuke Ohto, Hidetaka Kawakita, Katsutoshi Inoue, Shafiq Alam

Novel bio-adsorbent gel was prepared by immobilizing functional groups of glycidyltrimethyl ammonium chloride, a kind of quaternary ammonium chloride, onto polymer matrices of persimmon extract for the recovery of precious metals such as palladium(II) and platinum(IV) from chloride media. It was found that this adsorption gel exhibits high selectivity to gold(III), palladium(II) and platinum(IV) over base metals such as copper(II) and iron(III) while crude persimmon extract, the feed material, exhibits high selectivity only for gold(III). From the adsorption isotherms study, the maximum adsorption capacities for gold(III), palladium(II) and platinum(IV) were evaluated as 3.30, 1.67 and 1.00 mol/kg, respectively. Those for palladium(II) and platinum(IV) are higher than those of simple quaternary ammonium chloride type of chemically modified persimmon tannin gel and commercially available anion exchange resin.

Jan 1, 2016