Search Documents

By Michelle Lostra, Red Blanchette, Jan Babendererde, Greg Colzani

The City of Portland’s Westside CSO Project is constructing a deep tunnel system to reduce combined sewer overflows (CSO) from entering the Willamette River. Several kilometers of microtunneled pipelines connect the existing system to the new tunnel. The alignments encountered a variety of ground conditions, including fill, manmade obstructions (wood, steel piles, debris), fine-grained to dense coarse-grained materials, cobbles and boulders, all below groundwater. A slurry MTBM convertible to varying diameters, equipped with mix shield capabilities, was selected to cope with the conditions. This paper will discuss access shaft construction,

Jan 1, 2005

By Kanchan Mondal, Gopi Bylapudi, Anand Bhagwat

Corrosion of steel roof support systems can cause potential premature failure of the support, thus adversely affecting the excavation stability and rock-related safety. An in-house corrosion test system was designed and developed to test full-length roof bolts for material performance based on tensile load capacity and strength under different corrosive conditions found underground. The roof bolts tested are also used to identify the possible corrosion mechanisms that influenced the bolts’ performance over time. Initially, the most commonly used bolt material in the USA, the ASTM A615 grade 60 steel roof bolts, was tested with and without stresses in a simulated underground coal mining environment for approximately 6 months, and the results are discussed. Localized corrosion forms such as crevice and pitting were mainly observed after testing. The stressed and unstressed roof bolts with and without threads that were tested in alkaline coal mine corrosive environment for 6 months passed their load-bearing capacity as per ASTM F432 test standards. From the results, it is concluded that this test protocol could be applicable to test the material performance of different roof bolt metallurgies and coatings with desired modifications to the proposed methodology for the specific underground mine environment. This paper mainly discusses the test system and protocol and shortcomings of the system and makes recommendations based on the observations and results.

By Kanchan Mondal, Gopi Bylapudi, Anand Bhagwat

Corrosion of steel roof support systems can cause potential premature failure of the support, thus adversely affecting the excavation stability and rock-related safety. An in-house corrosion test system was designed and developed to test full-length roof bolts for material performance based on tensile load capacity and strength under different corrosive conditions found underground. The roof bolts tested are also used to identify the possible corrosion mechanisms that influenced the bolts’ performance over time. Initially, the most commonly used bolt material in the USA, the ASTM A615 grade 60 steel roof bolts, was tested with and without stresses in a simulated underground coal mining environment for approximately 6 months, and the results are discussed. Localized corrosion forms such as crevice and pitting were mainly observed after testing. The stressed and unstressed roof bolts with and without threads that were tested in alkaline coal mine corrosive environment for 6 months passed their load-bearing capacity as per ASTM F432 test standards. From the results, it is concluded that this test protocol could be applicable to test the material performance of different roof bolt metallurgies and coatings with desired modifications to the proposed methodology for the specific underground mine environment. This paper mainly discusses the test system and protocol and shortcomings of the system and makes recommendations based on the observations and results.

By Shosei Ph. D Serata

The Stress Control Method of mine design provides enhanced engineering control over the behavior of underground structures in comparison to conventional mine design methods. The same Method can be applied to achieve design control of surface subsidence. The basic mechanism relating undergroued deformation and surface subsidence is disclosed by mine simulations, using the REM (Rheological Element Method) computer code, whose predictions have been validated by field measurements. The key components of the underlying mechanism of surface subsidence have been shown to be the stress envelopes formed in the process of underground excavation. It has also been demonstrated that significant control of surface subsidence can be achieved by designing the geometry and timing of underground excavation to regulate the formation of stress envelopes. A field example is given in this paper to illustrate this application of the Stress Control Method.

Jan 1, 1986

By P. J. Rua

The Piedras Verdes copper mine is a new run-of-mine (ROM), heap leach, solvent-extraction/electrowinning (SX-EW) operation located 21 km (13 miles) north-northwest of the town of Alamos in the state of Sonora, Mexico. The Piedras Verdes copper mine is wholly owned by Frontera Copper Corp. (FCC), a Canadian corporation, through its 100 percent beneficial interest in Cobre del Mayo S.A. de C.V. (CDM), a Mexican registered company. The January 2008, minable reserves were estimated to be 193.6 Mt (213 million st) at a grade of 0.36 percent copper. The overall recovery of total copper was estimated to be 61.9 percent. The property has an additional 17-year life and is designed to produce 31.7 kt/a (70 million lbs/year) of cathode copper. Construction commenced in early October 2005. The first copper cathode was produced 12 months later at a total capital cost of $100 million. Elevations at the site range from 150 to 300 m (490 to 985 ft) above sea level. The area has excellent infra-structure in the form of towns, power, water, roads, rail, airfield and access to the deepwater port of Guaymas (Fig. 1). The surrounding area is also famous for its numerous polymetallic (lead, zinc, copper, silver and gold) epithermal veins. Some of these were mined for more than 200 years and provided the wealth on which the town of Alamos was built. The original village of Piedras Verdes was located in the area of the proposed openpit mine and, consequently, it was necessary to construct a new townsite 6 km (3.7 miles) to the south before project development could commence. The new town site (Fig. 2), complete with power and water supplies, roads, sewer system, schools, clinic and recreational facilities, was completed and occupied by 49 families in September 2005. CDM received its remaining permits from the Mexican environmental authorities on Sept. 20, 2005. This enabled the company to proceed with full-scale development. CDM owns or controls 27 mining concessions covering the resource. Surface rights to the Piedras Verdes project were controlled by four Ejidos (communal agrarian and/or ranching societies) and five individual landowners. CDM has acquired all surface rights necessary for its mining operations and associated facilities either through outright purchase or long term lease agreements.

Jan 1, 2008

From the massive equipment that moves the earth, to the parts that keep the equipment moving, it was all on display for more than 35,000 people who at-tended MinExpo 2008 at the Las Vegas Convention Center Sept. 22-24. In the largest show in the illustrious history of MinExpo, the success of the recent commodity boom was reflected in the more than 55,700 hm2 (600,000 sq ft) of floor space that was jam-packed with nearly 1,300 vendors. Among them, the makers of the industry?s largest machines, displaying their latest and greatest trucks, shovels, excavators, drills and other mining equipment. During the nearly decade-long commodities boom, equipment makers have worked hard to keep up with demand while also investing heavily in research and development. The beneficiaries of this R&D is the end user who saw first-hand at MinExpo 2008 the many advances that have already been made in safety, comfort and productivity from all the manufacturers. R&D has also helped spark more talk of automation, which is being used already at some of the world?s largest mines. Caterpillar and Komatsu have worked with the technology in surface mining and Bucyrus and Sandvik are among the industry leaders applying the science of automation to underground mines. Technology has in-creased greatly since the idea of moving massive equipment remotely was first knocked around and the idea of entire fleets operating around the clock seems to be getting closer to reality. But, until that happens, MinExpo attendees were treated to a show that featured some of the most impressive current machines the industry has to offer. In the largest booth space of the convention, Caterpillar (www.cat.com) displayed the culmination of an ambitious $280-million dollar investment, with the introduction of its new mining fleet of four new trucks. The F-series was un-veiled with common features in safety, cabs, engines, frames and bodies and Tier 2 compliant engines. The F series also features a return to the electric drive option. ?When our customers asked us for improvements to our mining trucks, we responded by making a record investment in every single truck in our line, as well as the increased capacity to produce more of them,? said Cater-pillar group president Stu Levenick. ?New technologies have allowed us to make trucks more reliable, easier to maintain and more friendly to the operator and to the environment.? The 793-series is in the 218- to 227-t (240- to 250-st) class that will be available in both mechanical (793F) and electric (793F ac) versions. The electric drive-only 313- t (345-st) 795F was also introduced, while the flagship 797B truck is in the process of being replaced by the new 797F mechanical drive, maintaining its 345- to 363-t (380- to 400-st) target payload. Completing Caterpillar?s new mining truck line will be new versions of the 785 and 789 mechanical drive trucks. The next generation of trucks will be phased into production during the next two years, with the Cat ac drive models expected to go into production in late 2010. The $280-million in-vestment is Caterpillar?s largest commitment ever to the mining industry

Jan 1, 2008

By K. Bounou, K. Komnitsas

"Risk quantification may be used as a sustainable development index in the mining industry, since it encompasses both economic and social factors. In addition, it may assist in the development of a framework, which is also indirectly related to sustainable development, to prevent accidents and improve health and safety standards. However, risk quantification in the mineral sector involves diverse activities and is considered a very difficult task. Although statistical data report accident severity rates, incident rates and accident frequency rates, none of these allow for accurate risk calculations. In this paper, two risk calculation formulas, which may be used to quantify risk, as well as to identify hazardous activities in a workplace, are proposed. Numerical examples are given based on statistical data available through the MSHA database. Also a combination of a decision/fault/event tree that allows risk quantification is presented."

Jan 1, 2005

By Doug Harding

The Niagara Tunnel Project (NTP) is a 10.4-km- (6.5- mile-) long, 14.4-m (47.5-ft) bored tunnel that will run under the city of Niagara Falls from the Upper Niagara River to the Sir Adam Beck power station. The completed project will enhance the capacity of the Sir Adam Beck power station by adding 500 m3 /sec (17,657 cu ft/sec) of water through the tunnel. The project uses the world?s largest hard-rock tunnel boring machine (TBM) at 14.4 m (47.5 ft) in diameter to excavate the tunnel. Features of the project include the use of a high performance (HP) main beam TBM, state-of-the-art ground support and tunnel logistics systems. A continuous conveyor is used for muck transport from the TBM to the disposal area In June 2004, the Ontario government announced that Ontario Power Generation (OPG) had been given approval to proceed with the third tunnel under the city of Niagara Falls ? the first two tunnels were constructed in the 1950s using drill-and-blast techniques. The third tunnel, appropriately named the Niagara Tunnel Project (NTP), consists of a 10.4-km- (6.5-mile-) long TBM-bored, concrete-lined tunnel with a finished diameter of 12.5 m (41.1 ft). In August 2005, OPG the selected of Strabag of Austria, one of the largest construction companies in Europe, as the contractor to build the NTP at a price of C$600 million. In September 2005, Strabag selected The Robbins Co. of Solon, OH to design, manufacture and deliver a new 14.4- m- (47.5-ft-) diameter high performance, state-of-the-art main beam hard rock TBM to be used in the excavation of the tunnel. To meet the aggressive construction schedule as requested by OPG/Strabag, the TBM needed to be sup-plied as ready-to-bore within a 12-month period after the contract was awarded to Robbins.

Jan 1, 2008

By D. Bour, C. Nyikos, R. Curtice

Fire in a coal mine can be disastrous on many levels. In most cases, when a fire is detected, mining operations cease and all personnel are evacuated. Underground coal-mine fires are difficult to extinguish, can burn for a long time, and often result in an extended period of lost production. In a worst-case scenario, the mine is permanently sealed and abandoned, resulting in lost jobs, lost natural resources, and possible devastation of the local economy. In some cases, seals placed within the mine to isolate the fire could eliminate the need for sealing the entire mine and the subsequent extended delay in returning the mine to full operation. Previous attempts to place remote seals to extinguish mine fires in active mines have been largely unsuccessful. The West Elk mine experienced an underground fire in early 2000. The fire could not be accessed and extinguished from the active mine workings. A method of constructing seals remotely by drilling boreholes into the affected area was needed to help isolate and extinguish the fire. This paper describes the process by which remote seals were constructed that successfully isolated the fire and provided a means of extinguishing the fire by flooding the area with water. The period of lost production in the West Elk mine was considerably shorter than is typical in similar situations.

Jan 1, 2002

With the dawning of a new century came the beginning of a new era in the coal industry. Instead of the traditional practice of only buying and selling produced coal in the United States, a coal futures market was established. The New York Mercantile Exchange began trading coal futures in July 2001. But, even in this new era, many of the old is-sues that have beset the coal industry still remain, as was evident in2001. Coal production increased to are cord level during 2001, according to preliminary data from the US Energy Information Administration(EIA). Production in 2001 rose by4% to 1.01 Gt (1.12 billion st), compared with 2000 (Table 1). This barely surpassed the previous record level of 1 Gt (1.11 billion st)set in 1998. Coal consumption remained unchanged. The additional production was used to replenish the depleted stockpiles that had resulted after two years of declining coal production and increasing coal consumption.

Jan 1, 2002

By A. K. Fallaw, G. Wang, L. R. Moore, S. Dobson, Y. Xiong, J. Gu

"As ores degrade, mining techniques and chemistries change to meet market demand and maintain product quality. The balance of recovery and grade is a significant challenge in the Crago Process where an anionic collector is used to float phosphate, followed by acid scrubbing, then an amine float to improve product grade. As the grade is a requirement for DAP and MAP production, recovery is the criteria to suffer. Phosphate losses in the amine float can bring overall recovery down by as much as 18%, creating a growing need to think outside the box to improve recovery. This paper will focus on the theory of amine tail recycling and the best methods to optimize the overall phosphate recovery by recycling the tails from the cleaner flotation step. INTRODUCTION In 2014 the total US phosphate production was down 13% over the prior year, from 31.9 to 27.1 Mt, which accounts for 12.32% of the world’s phosphate rock production. Florida and North Carolina phosphate production accounted for 80% of total US phosphate production, which was down from 85% the previous year. This decline is due in part to the closing of the last phosphate mine in Polk County, FL - which had an operating phosphate mine for over 100 years (Gurr, 2015). Another factor contributing to the reduction in contribution from FL & NC is the increasing challenges in beneficiating the remaining ore deposits. The Central Florida mining district has historically been in the Bone Valley deposit, where raw apatite was abundant with P2O5 values as high as 15%. The Bone Valley ore also had characteristics favorable to beneficiation to 27.5-29.7 %P2O5 while achieving recoveries above 86%. The move southward into the Hawthorne Formation has seen the ore feed grade hit some historic lows, and the matrix characteristics pose more challenges to phosphate producers. The Hawthorne Formation experienced lateritic weathering after the Bone Valley formation which altered the apatite to aluminum phosphate minerals, and alteration of montmorillonite to kaolinite, releasing MgO that caused the dolomitization of the top of the Hawthorne limestone (Cathcart, 1966). Elevated levels of dolomite can yield an increase in slurry viscosities, reduce production rates, and increase energy costs in the wet-acid fertilizer process. The MgO will also act to dilute grade, making it more difficult to achieve a standard 18-46-0 product (McHardy, 1981)."

Jan 1, 2016

The global tunneling industry has many challenges, both technically and financially, with the latter likely to be a significant feature over the next few years. Many industries have ad-opted standard practices in order to overcome specific technical challenges, from which standard out-comes are anticipated. In tunneling, however, every project is unique so standardized practice is not easy. This requires original thinking and being open to adopting new techniques and technologies as they emerge. Sprayed waterproofing is a hot industry topic and a paper recently presented at the North American Tunneling conference not only discussed this methodology for achieving a dry tunnel but also how it can reduce build costs and construction time. Despite their being relatively few ?universal truths? throughout the tunneling industry, there is one opinion that appears to be shared by most in the sector, ?all tunnels leak.?

Jan 1, 2010

By J. Swanepoel, J. H. van Laar, J. C. Vosloo, W. A. Pelser

Deep-level underground mining costs in South Africa are continuously rising due to the increased depth at which gold is being mined, resulting in a rise in virgin rock temperature and an increase in cooling requirements. Therefore, mines must evaluate various ventilation and cooling optimisation projects required to be implemented throughout their life of mine (LOM). This study develops a method to identify and prioritise large capital expenditure (CAPEX) underground environmental improvement projects, to improve thermal comfort underground. The solution presents a ‘multi-criteria decision-making’ (MCDM) process, incorporating the ‘analytic hierarchy process’ (AHP) and the ‘technique for order performance by similarity to ideal solution’ (TOPSIS) into the method to provide for scientific decision-making. These projects are evaluated based on four criteria, namely project risk, the impact on the underground thermal comfort, cost, and implementation time. This study’s solution uses ventilation simulations to determine the impact of the projects on the underground environment. The identification and evaluation of an environmental improvement project to best suit the current economic climate, while improving underground conditions and decreasing the safety risk is an essential aspect of the solution developed in this study. The method was implemented on a mechanised deep-level underground mine and showed that surface refrigeration is the most suitable alternative, which was implemented at the case study mine as validation of the developed solution. The study proves that the MCDM method is an adequate solution to incorporate subjective criteria into the decision-making process, resulting in a scientific and structured approach to making significant and complex decisions.

Feb 17, 2023

By D. Govender

In recent years, economies of scale have continued to drive copper projects to larger throughputs to offset depleting lower grade resources. A decade ago there were only a small number of projects that stretched beyond 100,000 Mtpd throughput rates. Nowadays and moving forward virtually all the major copper projects are sized beyond this, with throughput rates up to 250,000 Mtpd now under evaluation for a number of key projects in Chile and Peru. This paper explores the development from the 160 m3 flotation cells, through to the 257 m3 cells and nowadays to the 660 m3 machines. The contributions of specific copper concentrators to this growth phase are reviewed herein. The historical basis of flotation machine scale-up is also briefly discussed. Metallurgical results as well as layout, maintenance and operational aspects are highlighted.

Feb 27, 2013

Ceremonies for the induction of five mining industry pioneers into the National Mining Hall of Fame will be on Sept. 12, 2009 at the Charles F. Barber Pavilion of the Museum Convention Center in Leadville, CO. The five inductees are: Paul A. Bailey, 82, Richard T. Moolick, 89, William Braden and Alonzo Pawling and Henry Harnischfeger. Paul A. Bailly was president of Bear Creek Mining Co., the U.S. exploration subsidiary of Kennecott Copper, from 1961 to 1967. In 1968, he joined Occidental Petroleum Corp. and was tasked with creating the company?s international mining division, Oxymin, which he led as president through 1983. During his distinguished career, Bailly participated in numerous significant mineral discoveries, developed a new exploration philosophy and made important additions to the mineral exploration literature. William Braden was the first to recognize the immense potential of the El Teniente orebody in Chile. He founded Braden Copper Co. and developed the El Teniente Mine which now, 100 years later, remains the world?s largest underground copper mine. Braden?s endeavor survives to-day as the El Teniente division of the Chilean state copper company, CODELCO. T. (Dick) Moolick established a lasting legacy in the mining industry, first during a 35 year career with Phelps Dodge Corp. and then as the driving force in establishing the National Mining Hall of Fame and Museum in Leadville. The Hall of Fame and Museum ? a monument to the memory of the men and women who pioneered the discovery and development of the United States? natural resources ? has become one of the fi nest museums in the western United States.

Jan 1, 2009

By S. K. Oraee

Managers always look for systems with minimum hazards. The hazards create problems for performance of projects. The largest and most important hazards of working underground mine can be related to health, safety and environmental, because if one of these sectors be in hazard, maybe lead to close mine. Failure mode and effects analysis (FMEA) is a widely used quality improvement tool to identify the potential failure modes for measuring reliability of a product or a process. FMEA is performed by developing a risk priority number (RPN), which is the product of severity, occurrence, and detection ratings. On the other hand, with regard to uncertainty in the decision-making, fuzzy theory will be able to model this uncertainty. Fuzzy FMEA provides a tool that can work in a better way with vague concepts and without sufficient information than conventional FMEA. This article by using Fuzzy FMEA and based on HSE criteria evaluate hazards of Parvade No. 1 Mine in Tabas Coal Mine. The results demonstrate the most hazardous parameter is rock burst in this mine.

Jan 1, 2011

By Paul C. Schmall, Lucian P. Spiteri, Arthur B. Corwin

Moving groundwater is generally recognized as the most adversarial condition for ground freezing. Moving groundwater can occur due to natural or man-induced groundwater flow, but either way may result in freeze formation difficulties. History has shown that if the condition goes undetected, catastrophic failure of the frozen shaft or excavation can occur. The success of ground freezing under potentially flowing groundwater conditions depends on an evaluation of the likelihood for this condition; an accurate and early diagnosis, with a careful evaluation of freeze pipe temperatures and piezometer water levels; and timely reaction to mitigate the possible delays. Successful remedial measures have included the reduction of ground permeability by modifying the soil properties between the freeze pipes with various kinds of grouting, or increasing the freezing effect by adding freeze pipes and/or the use of liquid nitrogen as the freezing agent.

Jan 1, 2007

By William R. Yernberg

In October 1999, Liebherr-America, Liebherr Construction and Liebherr Mining Equipment held anopen house at its Newport News, VA, plant. The open house was held to celebrate the company’s50th anniversary and to demonstrate the new TI 272mining truck. Attending the open house members of the media, vendors and company representatives from all over the world. In his introductory comments, company president Peter Eller announced Liebherr’s dedication to expanding its presence in North America. Liebherr now has 30 dealers across the United States. As part of the open house, a brief history of Liebherr was presented, beginning with its creation in1949. Liebherr engineering and sales representatives were available to answer questions.

Jan 1, 2000

By A. J. Thompson

The Metropolitan Transportation Authority (MTA) East Side Access project (ESA) will, when it is complete, provide a new link to the east side of Manhattan from Long Island, NY that, linked with the Second Ave. Subway currently under construction, will assist in relieving overcrowding at Penn Station as well as the Lexington Ave. subway. ESA will bring Long Island Railroad (LIRR) directly from Long Island into a new station located 37 m (120 ft) beneath the existing Grand Central Terminal (GCT) located in the heart of Manhattan. It will connect the LIRR?s mainline tracks in Queens, via the existing 63rd Street Tunnel under the East River, to a new terminal constructed within, and beneath, the historic Grand Central Terminal.

Jan 1, 2012

By V. A. Leach, J. R. Johnson

The calculation of the dose to the bronchial epithelium, lungs and other body tissues from exposures to airborne radon and thoron daughters requires a knowledge of the pattern of deposition in the respiratory system and clearance from it. Exposure to radon or thoron daughters is measured in units of Working Level Months (WLM), which is independent of the aerosol particle size, the fraction of daughters that are attached to the aerosol and the degree of disequilibria between the daughters, and age and breathing rate of the subject. These factors will influence the deposition and clearance, and hence dose. It is therefore of interest to find the relationship between WLM and calculated dose as a function of aerosol size, unattached fraction, and disequilibria, and of age and breathing rate, and to define ranges for these parameters for which WLM is an acceptable measure of the risk. This presentation briefly reviews the two dosimetry models being considered by a current Nuclear Energy Agency (OECD) Working Group, and using these models, defines limits on parameters for which the WLM is applicable.

Jan 1, 1981