Search Documents

By George E. Valadão, Iván A. Reyes, Mizraim U. Flores, Armando C. Araujo, Rubén H. Olcay

Dewatering tailings to higher grades than paste produces a stable deposit that typically does not require retention dams and is called a “dry stack.” A proposal of different dewatering techniques applied in the fine tailings produced after final desliming phase, obtained from the treating of phosphatic ores, is the main objective of this work. The dewatering techniques evaluated were column thickener, deep cone classifier, and hyperbaric filtration. Calcite and dolomite were the main mineral contained in the phosphate tailings and these have a very fine granulometry; the tailings presented different behaviours related to the dewatering technique applied. The test column thickener and deep cone classifier with the best operational parameters found to obtain a maximum percentage of solids in mass were ~ 71% and ~ 67%, with values of yield stress ~ 200 Pa and ~ 100 Pa, respectively. In the hyperbaric filtration, a cake with ~ 10% moisture was obtained. This indicates that the transportation conditions are not the same. The overflow turbidity levels obtained from column thickener and deep cone classifier test did not exceed the value 100 NTU, whilst for the filtrate of the hyperbaric filter obtained values ~ 800 NTU. It was possible to preliminary estimate the recovery direct of water, considering each dewatering technique for final disposal of the tailings. The best dewatering techniques obtained were in the following order for the disposal in phosphate fine tailings dams; the hyperbaric filter showed an excellent dewatering capacity with productions rates around 160 kg h− 1 m− 2 for moisture cake of 10%, followed by the column thickener and deep cone classifier with paste ~ 71% of solids (W/W) and high-density slurry ~ 67% of solids (W/W), respectively.

Dec 23, 2023

By Peter N. Calder

There is little doubt that the stability of both highwalls and spoil piles is essential to efficient strip mining. Accurate determination of the appropriate geotechnical parameters will pay dividends during mining, but only if the mine operation closely follows the engineering plans which have incorporated These factors. Productivity is invariably higher in mines where failure of highwalls and spoil piles does not occur. This is the result of the reduced rehandle and better working conditions found in stable mines. Control of the waste piles and highwalls also leads to better coal recover since failures can result in the burial of uncovered coal, which is then lost to mining. Safety is an important consideration. The importance of providing a safe working place for employees and of protecting costly mining equipment is hard to overemphasize. For miners, working in areas where instability exists, the degree of hazard involved in their occupation is increased particularly where night operations are involved. It is true, too, that there have been many cases where loading equipment has been buried and severely damaged by failures.

Jan 1, 1980

By T. J. Lutz, S. Gallagher, J. R. Srednicki, J. J. Sammarco

The Illuminating Engineering Society of North America reports that an underground mine is the most difficult environment to illuminate (Rea, 2000). Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) are conducting ongoing studies designed to explore different lighting technologies for improving mine safety. Underground miners use different visual cues to escape from a smoke-filled environment. Primary and secondary escapeways are marked with reflective ceiling tags of various colors. Miners also look for mine rail tracks. The main objective of this paper is to compare different lighting types and ceiling tag colors to differentiate what works best in a smoke-filled environment. Various cap lamps (LED and incandescent) and lasers (red, blue, green) were compared to see which options resulted in the longest detection distances for red, green and blue reflective markers and a section of mine rail track. All targets advanced toward the human subject inside of a smoke-filled room to simulate the subject walking in a mine environment. Detection distances were recorded and analyzed to find the best cap lamp, laser color and target color in a smoke environment. Results show that cap lamp, laser color and target color do make a difference in detection distances and are perceived differently based on subject age. Cap lamps were superior to lasers in all circumstances of ceiling tag detection, with the exception of the green laser. The incandescent cap lamp worked best in the simulated smoke compared to the LED cap lamps. The green laser was the best color for detecting the tags and track compared to the red and blue lasers. The green tags were the easiest color to detect on the ceiling. On average, the track was easier for the subjects to detect than the ceiling tags.

Jan 1, 2013

By Kyeong Woo Chung, Rina Kim, Ho‑Seok Jeon, Yeongjin Ahn, Byunghun Go, Min‑seuk Kim, Hong‑In Kim, Sujeong Lee, Yuik Eom

The study focused on the recovery of vanadium from a Korean vanadium-bearing titaniferous magnetite (VTM) ore, examining the behaviors of magnetic separation and Na2CO3 roasting-water leaching. Two concentrates were prepared using single-stage dry magnetic separation and three-step wet magnetic separation, resulting in V2O5 grades of 0.8% and 1.0% and major gangue mineral SiO2 contents of 6.5% and 1.7%, respectively. These concentrates were subsequently roasted at 1050 °C with the addition of Na2CO3 and then water-leached at 25 °C. Various stoichiometric ratios of V2O5 to Na2CO3 were tested, ranging from 1:1 to 1:40 of the theoretically required amount. As the amount of Na2CO3 increased, the vanadium leaching efficiency showed fluctuations between 4 and 35% for ratios of 1:1 to 1:10, while it linearly increased from 4 to 82% for ratios of 1:10 to 1:40 in the leaching of the low-grade concentrate. In contrast, the leaching efficiency increased from 47 to 74% for ratios of 1:1 to 1:8 and then sharply rose to 84% at a ratio of 1:10 in the leaching of the high-grade concentrate. Subsequently, it reached a plateau of 92 to 94% for ratios of 1:20 to 1:40. The difference in leaching efficiency was primarily due to the reaction of gangue minerals with Na2CO3, which hindered vanadium leaching from the VTM concentrates. This hindrance was notably more pronounced in the low-grade concentrate with the lower salt ratio, as the gangue minerals exhibited a preference for consuming Na2CO3 over vanadium. The mineral formation was analyzed in detail using XRD and MLA to shed light on the mechanism of different vanadium leaching behavior depending on the concentrate grade and vanadium to salt ratio. Based on the results of this study, it is evident that applying a proper magnetic separation procedure is significant to achieving satisfactory vanadium recovery with less salt amount by removing gangue minerals ahead.

Mar 15, 2024

By Jon C. Yingling

Lean manufacturing, pioneered by Toyota, has been credited with the most significant improvements in production efficiency and product quality since the transformation from craft manufacturing to mass production in the early 20th century. It represents a comprehensive philosophy for structuring, operation, control, and management of production systems that is believed to have wide applicability. This paper outlines major lean manufacturing principles and discusses their potential for application in the mining industry.

Jan 1, 1999

By G. A. Kordosky

LIX® 34 liquid ion exchange reagent, one of a totally new class of metal extractants, is discussed in terms of its properties. Specifically, these properties include improved selectivity for copper and greater recovery. Some comparisons to the well known General Mills' LIX® 64N have been made. Particular emphasis is given to treating solutions containing very low copper values and high impurity levels.

Jan 1, 1976

By D. Spitty

There are enormous complexities with mine planning and the problem itself presents a huge challenge to the existing mine planners performing this activity. Mine planning optimization supports planners to determine ?What are the best increment excavation sequence and the best material blending combination such that throughput, quality, cost, utilization and Net Present Value (NPV) targets are met?? It is achieved through using an advanced scientific approach that has been specifically adapted to address the mine planning dilemma.

Feb 23, 2014

By Chee Theng

"Mining professionals are a resilient lot. Sure, copper prices are dismal, permitting processes seem interminable and the top mining companies are shedding jobs like a Shetland sheepdog sheds hair. All the more reason to hone technical skills, reconnect with old contacts and get one’s finger on the pulse of the industry.More than 400 did just that in the balmy sunshine and among the saguaro cactus of the Tucson venue of the SME Arizona Conference.Giving the keynote speech was Patrick Merrin, vice president at Hudbay Minerals (see box), while the luncheon speaker was University Distinguished Professor Mary Poulton, director of the Lowell Institute for Mineral Resources at The University of Arizona.“Attendance was great, especially given the copper price,” said Ta Li, vice president of business development at Tetra Tech and 2001 SME President. “The luncheon speaker was one of the better ones in recent years. Her talk contained a lot of fresh ideas, and practical versus theoretical concepts.”Talk about values, not economicsPraise was unanimous for Poulton, who gave a thought-provoking talk on “The New Face of Mining: The Culture Change for Compatible Mining.” Corporate social responsibility has been embraced by the metals mining industry, and it’s being done right, she said. “So why do we have more conflict? Why are there more protests? Why does permitting take longer and longer?” Poulton made a case for an approach based on compatible, rather than sustainable, mining to present a new face of mining that can be compatible with communities, cultures and the environment, and still be profitable. When the mining industry starts to talk about compatibility between what it is doing and what “me,” as the consumer, wants, what “we,” as citizens of a community, want, and what’s good for the “world,” we’re going to see the next culture change happen, she concluded."

Jan 1, 2015

By D. Akers

Many of the trace elements found in coal are associated with mineral matter, making it possible to remove them by physical coal cleaning. As part of work funded by the Electric Power Research Institute, both conventional and advanced coal cleaning processes were found to provide large reductions in the concentration of many trace elements that, if released into the atmosphere, are considered to be potentially toxic or environmentally harmful. Advanced physical cleaning technologies appear to provide greater reductions than conventional technologies. Chemical cleaning processes may also remove many trace elements, possibly including organically-bound elements such as beryllium. Care must be taken in the disposal of coal cleaning plant refuse because oxidation and leaching of this material can create highly acidic leachate and many trace elements are mobile in an acid environment. Laboratory leaching procedures are potentially useful in determining the degree of risk of water contamination by trace elements should an acid environment form.

Jan 1, 1992

By R. A. Seitz

This paper presents a framework for analyzing the theory and industrial practice of coal flotation and gives some examples of its use for understanding flotation phenomena and optimizing/controlling flotation circuit performance. It is based on extensive laboratory and in plant test work conducted over the past several years by researchers at MTU as well as an analysis of the literature. Previous researchers have usually considered either the surface chemistry or the kinetics of coal flotation behavior, only rarely have these factors been considered together. However, these factors must be considered together in order to gain a clear understanding of the theory underlying coal flotation such that its practical application can be optimized. Fortunately, this complex objective can be achieved by considering the recovery and rate of recovery of the different types of particles present in the feed to coal flotation circuits and the fundamental mechanisms responsible for these recovery phenomena. The influence of three major groups of variables must be considered: control variables (reagent additions, aeration rate, etc.); disturbance variables (feed pH, percent solids, etc.); and circuit design variables (number of cells, circuit arrangement, etc.). Each of these groups of variables affects process kinetics in a clearly understandable manner, which, once determined, is extremely useful in circuit design and optimization. This paper includes a discussion of the use of the proposed framework to explain the effects of some coal characteristics on flotation performance. In addition, an example of using this analysis to optimize the performance of a coal flotation circuit using frother and collector addition levels is included.

Jan 1, 1985

By N. Cruickshank

Gas outbursts occur as sudden eruptions of gas and minerals from the face of a mine heading as the heading approaches potentially burst-prone (or anomalous) zones of rock. Such outbursts have resulted in considerable damage to equipment and in some cases lives have been lost. Characterizing these anomalous zones and detecting their presence is therefore vital to safe mining. Certain significant characteristics associated with the outburst-prone zones are: (1) the presence of fluid inclusions, (2) unstable stress conditions, (3) characteristic geologic structures, (4) certain physical properties of the rock, and (5) micro-seismic activity. Geophysical and engineering methods for detecting these characterisitcs are discussed and are considered with respect to their past success and future potential for predicting gas outbursts.

Jan 1, 1985

By John S. Lagarias

While systems to remove sulfur oxides from flue gases have been used at coal fired power plants since 1931, critical need for flue gas desulfurization has only occurred since the late 1960s following the passage of the Clean Air Act Amendments. Commercial and advanced flue gas desulfurization processes (FGD) are reviewed. Advantages and disadvantages of the processes are discussed. Regulatory requirements leading to the development of FGD systems are identified. The location and operation of coal fired plants may be determined more and more by the regulatory requirements for sludge disposal, waste, water discharge and air emissions.

Jan 1, 1978

By Norman F. Schulz

The technical excellence of separation achieved in a mineral concentration process, or any other process where two constituents of any kind are physically separated from each other, is expressed uniquely and quantitatively by the Separation Efficiency: ES = (R ? Rg) where R is the percentage of the valuable constituent and Rg the percentage of the waste appearing in the concentrate. The Separation Efficiency meets all the usual requirements of a true efficiency and is independent of the nature of the process used. It can be visualized as the percentage of the feed material that, in effect, actually undergoes complete separation while the rest of the feed is distributed randomly and unchanged into the two separation products.

Jan 1, 1969

By F. Djahanguiri

The U.S. Bureau of Mines is conducting research on underground stope leaching of metalliferous ores to minimize the environmental impact of ore processing on the surface and to maximize minable reserves. An aspect of this research is to minimize pregnant solution losses and/or groundwater contamination by leach solutions. Bulkhead design and construction are important issues for solution control and stope leaching economics. A reinforced concrete bulkhead was designed, constructed, and tested for solution control in an underground mine near Idaho Springs, CO. This paper presents the bulkhead design methodology and construction procedure.

Jan 1, 1995

By M. Li, J. K. Thompson, A. S. Azman

Powerful mining systems typically generate high-level noise that can damage the hearing ability of miners. Engineering noise controls are the most desirable and effective control for overexposure to noise. However, the effects of these noise controls on the actual hearing status of workers are not easily measured. A tool that can provide guidance in assigning workers to jobs based on the noise levels to which they will be exposed is highly desirable. Therefore, the Pittsburgh Mining Research Division (PMRD) of the U.S. National Institute for Occupational Safety and Health (NIOSH) developed a tool to estimate in a systematic way the hearing loss due to occupational noise exposure and to evaluate the effectiveness of developed engineering controls. This computer program is based on the ISO 1999 standard and can be used to estimate the loss of hearing ability caused by occupational noise exposures. In this paper, the functionalities of this software are discussed and several case studies related to mining machinery are presented to demonstrate the functionalities of this software.

Jan 1, 2016

By Hugh D. Olmstead

Typical operations necessary to develop oil and gas reservoirs are reviewed, including exploration, drilling, cementing, completion, work over, sand control, stimulation, enhanced recovery and production. The role of industrial minerals in these operations is described. Some of the opportunities and problems affecting increased use of industrial minerals in drilling and stimulation are discussed.

Jan 1, 1983

By Katerina Adam

During wet grinding the electrochemical interactions between grinding media and pyrrhotite not only accelerate the media wear but also adversely affect the flotation response of the sulfide mineral. A possibility of remedying the adverse effect on its floatability by applying electric potentials to grinding media was examined. Flotation tests, Auger electron spectroscopy and x-ray photoelectron spectroscopy were used to study the surface properties of pyrrhotite. Although anodic polarization of the steels increased the metal loss by corrosion, the flotation recovery of pyrrhotite was increased. In the case of cathodic polarization, the flotation recovery improved in a narrow range of overpotentials. At higher cathodic overpotentials, however, the floatability of the mineral was progressively lowered although the corrosive wear of grinding media might be reduced.

Jan 1, 1984

By Homer E. Harris

As a result of the enactment of the Federal. Coal Mine Health and Safety Act of 1969 1, the Department of Health, Education, and Welfare (HEW) has been carrying out research in the "field of coal mine health". The National Institute (formerly Bureau) for Occupational Safety and Health (NIOSH) was designated the agency within HEW to be responsible for such research activities. One of the early programs sponsored by NIOSH was undertaken by Eastern Associated Coal Corp., with the Harvard University School of Public Health participating as a subcontractor to Eastern. This program on Coal Mine Respiratory Protective Devices, which started on June 30, 1970, had five major objectives as follows: a. to determine current status of respirator usage with respect to duration and frequency, types. and maintenance b. to determine acceptability ( and reasons therefor) of currently used units c. to determine protection factors provided by respirators worn by working miners d. to make recommendations on ways to improve existing units, or on research needed to develop new types of respiratory protective devices for coal miners e. to provide recommendations to mine management on more effective use of respiratory protective devices

Jan 1, 1973

By M. Kaya

This paper presents an experimental method to determine the degree of gangue entrainment in mechanical flotation cells and proposes new and inexpensive methods to lessen it. The applicability of froth washing and vibration was studied in laboratory, pilot plant, and plant scales. The effect of wash water on metallurgical performance was tested with various streams from the Falconbridge Strathcona mill at laboratory, pilot, and plant scales, with the 2nd cleaner at the Eastmaque Kirkland Lake mill, and with the 2nd and 3rd zinc and 3rd and 4th copper cleaners at Les Mines Selbaie mill. It was found that gangue recovery was closely related to water recovery in all systems. Wash water at an optimum superficial rate from 0.03 to 0.07 cm/s reduced entrainment by anywhere from 30X to 70X. Wash water can be further assisted by mechanical and ultrasonic vibration of the froth. A further rejection of 10 to 20X becomes possible. As a result of this work, a number of plants in Canada and in the United States have evaluated and/or are now using froth washing.

Jan 1, 1990

By A. Almeida, D. Castro, K. Ingmarsson, D. Ferreira, R. Tamir

Mine-to-mill improvements can be initiated at any stage, but it is our assertion that drilling accuracy is a practical anchor in any operating mine or quarry for a structured continuous improvement process. This paper will: 1. Define deviations from plan and provide some best practices for maintaining drilling accuracy. 2. Introduce tools and methods to monitor and calculate consequences of accurate versus inaccurate drilling. 3. Demonstrate the use of these tools and methods and their impact on one cost item, the mitigation of oversized material by a hydraulic hammer. 4. Provide recommendations for implementing improvements.

Feb 1, 2023