Search Documents

By Anna Kate Miller, James J. Brady, Hamza Jaffal, Ritika Sangroya, Chadi El Mohtar, Wing Shun Kwan

"The design of an appropriate pre-grouting program can be the difference between a successful tunnel construction and an expensive on-the-go repair. However, current grout design relies heavily on rulesof- thumb and outdated charts. The geotechnical investigation is rarely targeted towards grouting design and the final grouting decisions are made based on fines content or soil classification. The current paper presents an experimental study performed to determine the optimal grout for a tunnel in soft ground below the ground water table (GWT). The testing program consisted of sieve analysis and undrained static triaxial tests on reconstituted sonic samples. Rheological tests were used to compare the different grout mixes and identify best candidates before performing one-dimensional permeation tests. Pressure and volume measurements during the permeation tests, along with the unconfined compression strength results on the permeated soils, helped evaluate the filtration potential for the different grouts and select the optimal grout.INTRODUCTIONConstruction of the Millwoods Double Barrel Replacement Project commenced in 2009 and was expected to be completed by 2015. To facilitate ongoing city development in south Edmonton, the City implemented construction of a major sanitary trunk network along 91st Street and 30th Avenue. The project involved the design and construction of approximately 1.2 miles (2 km) of 7.8-ft (2,400 mm) sanitary tunnel and 2.1 miles (3.4 km) of 11.5-ft. (3,500 mm) and 9.5-ft. (2,900 mm) storm tunnel. Part of the project also involved the conversion of the existing double barrel storm and sanitary trunk to full sanitary service, and reconnecting the local storm sewers from the double barrel pipe to the new storm tunnel. The tunnels range in depth from 26-ft. (8 m) to 115-ft. (35 m) and are being installed using a one pass system with precast concrete segmental liners."

Jan 1, 2016

By Richard Chojnacki

The western united States is not usually noted for the production of fluorspar; however, many significant fluorspar districts do occur in the Rocky Mountain region and constitute a resource of sizable dimension and major potential. This is particularly true within the area of the West served by the rail lines of the Union Pacific Railroad (see Figure 1). Fluorspar deposits near the Union Pacific have produced over 1.3 million tons of finished fluorspar products from 2.3 million tons of ore. Approximately 80% of this production was of acid-grade and 20% of metallurgical-grade fluorspar. Production of ceramic-grade was negligible. Through the years substantial production has come from eight mining districts. Five of these have produced metallurgical-grade and three acid-grade. The best-known fluorspar producing area in the West is the Jamestown Mining District. It was one of the first producers of fluorspar in the western United States and is estimated to have produced over 500,000 tons of finished fluorspar from over a million tons of ore. The district encompasses approximately 36 square miles in central Boulder County, Colorado, about 9 miles northwest of the City of Boulder. Although small shipments were made from the district as early as 1873 or 1874, significant sustained production was not achieved until 1940 when the General Chemical Company, now a division of the Allied Chemical company, acquired the Alice, Burlington, Chancellor,

Jan 1, 1971

By M. T. Webster

Views about the proper aim of public policy are, of course, matters of perspective and debate. Regardless of perspective, one would assume some consensus around the view that public policy ought to encourage mine operators to seek independent and critical assessments of worker safety and health at their operations through voluntary auditing. However, a review of the law on this topic shows that there is little to no manifestation of such a policy. Indeed, the balance of this paper, with a couple of exceptions, is devoted to the existing legal pitfalls that should be considered before a safety and health audit is conducted at a mine. While attorneys, particularly litigators like the author, might tend to focus on the potential problems that could arise from any given situation, the fact that most of this paper is devoted to potential legal concerns associated with auditing is a realistic reflection of the current state of the law. Specifically, this paper addresses the interplay between voluntary safety and health audits conducted at mines regulated by the Mine Safety and Health Administration (MSHA), and the administrative and civil legal issues related to such audits. The paper first provides an explanation of how and by whom an audit is conducted. The paper also addresses whether voluntary safety and health audits may be considered privileged and kept confidential in administrative and civil proceedings. Finally, selected legal issues related to such audits that could arise in administrative and civil litigation are discussed.1

Jan 1, 2012

By CHENGLONG XU, HAORAN LI, YALI FENG, JINRONG JU, Shunliang Liu

In order to realize the resource utilization of spent hydrodesulfurization catalyst, a solvent extraction-oxalic acid precipitation process is studied in this paper for efficiently recovering vanadium, nickel, and aluminum from the acid leaching solution of spent hydrodesulfurization catalyst. The process conditions for extracting vanadium with Cyanex 272 and precipitating nickel using oxalic acid as a precipitation agent were explored in detail. The results show that vanadium (IV) in the sulfuric acid medium containing nickel and aluminum was efficiently and selectively extracted by Cyanex 272. After three-stage countercurrent extraction, the extraction efficiency of vanadium was 99.76%, and the co-extraction efficiencies of nickel and aluminum were only 2.47% and 1.87%, respectively. Thermodynamic calculation shows that the extraction of vanadium (IV) from the sulfuric acid medium with Cyanex 272 is an endothermic reaction. The innovative method of oxalic acid precipitation was used to recover nickel from the raffinate, achieving selective extraction of nickel from the solution containing a high concentration of aluminum. The precipitation efficiency of nickel was 98.58%, while that of aluminum was only 0.75% under optimal conditions. The proposed flowsheet for the separation of vanadium, nickel, and aluminum from acid leaching solution may provide a new idea for the comprehensive recovery of valuable metals from spent hydrodesulfurization catalyst.

Nov 30, 2022

By F. N. Kissell

U.A. Mine Safety and Health Administration (MSHA) coal dust compliance data sometimes shows high silica levels at roof bolters. However, it is unclear whether this silica normally originates from the bolter itself or from other dust sources upwind of the bolter research studies to answer this question at individual mines have been conducted. However, operational practices vary from mine to mine thus, the information gleaned from any one study cannot be accurately extrapolated to describe silica dust sources in most mines. In this paper, three decades of bolter dust research are reviewed the results showed that, while inadequate maintenance on the bolter dust collection system can result in excessive dust, more likely reasons for high silica levels are inadequate ventilation of the mine entries being bolted and dust traveling downwind from the continuous miner to the bolter. Scrubbers on continuous miners may not be removing as much silica dust as expected. Mining Engineering, 2011, Vol. 63, No. 10, pp. 78-82. Official publication of the Society for Mining, Metallurgy and exploration, Inc.

Jan 1, 2011

By T. Hawthorne, H. Barnes

Homestake Mining Company has developed an estimating model, based on other closed projects, to audit and prepare new estimating plans. The results of recent closure audits reveal that the original budgets were often insufficient to cover the present expected expenses. Some of the major areas where technical challenges and costs are increasing include heap leach pile detoxification and rinsing, tailings dam closure, water management and treatment, abatement of contaminated soils, and many others. Risk and sensitivity analysis of each category will develop a level of confidence in the estimate and allow management to focus on the pertinent issues. Periodic audits of closure plans and costs throughout the life of mine serves to focus management attention on the complete costs of production. This will result in improved overall planning and management, and reduce the number of missed opportunities for savings.

Jan 1, 2000

By Richard A. Grieve

A 63.5 metric tons per hour (70 TPH) demonstration coal preparation plant was constructed on the Iowa State University campus, Ames, Iowa, as a part of the Iowa Coal Project funded by the state of Iowa and administered through the Energy and Minerals Resources Re-search Institute. Processing equipment in the plant circuit includes a heavy media separator, concentration tables, separating and dewatering screens, and conveying equipment. Coal samples of size 907 metric tons (1000 tons) with sulfur contents ranging from 2.5 to 8.75% sulfur from seven mines in the state of Iowa have been pro-cessed in the plant. Sulfur reductions have averaged 35%. With ash reduction averaging 45%. Equipment for advanced fine coal beneficiation research is currently being installed in the plant to include a slurry pretreatment circuit, froth flotation, oil agglomeration, pelletization, hydrocyclones, advanced design thickener and disc filtration.

Jan 1, 1978

By W. W. Edgerton

Construction projects may be delivered under one contract package or multiple packages divided by discipline, geographic location, or other characteristics. Dividing the construction into contract bid packages is called contract packaging, and is a vital and strategic aspect of effectively delivering tunneling projects. The process of contract packaging considers many factors, including the type of project, location, and owner?s priorities. This paper describes the key facets of the contract packaging process used recently on several tunnel projects, reports, where possible, on the success of the process, and concludes with recommendations for applying this process to achieve the right contract package.

Jan 1, 2008

By Miguel Reyes, Chenming Zhou, MATTHEW GIRMAN

Electromagnetic energy emitted from electronic devices has been known to interfere with other electronic systems, hindering their ability to function properly. Mines have many electronic devices critical to the health and safety of mine workers that could be negatively affected by electromagnetic interference (EMI). To ensure that devices are electromagnetically compatible, tests must first be conducted to measure emissions and check for immunity. Standards are available across multiple industries that prescribe emission limits and test methods for electronic devices. A literature review was conducted in this study, and an overview of EMI standards in other industries is provided. Also, an example of how a standard can be applied to mining equipment is presented.

Nov 1, 2022

By S. Chatterjee, A. K. Gorai, Sahendra Ram, Kapil Kumar, J. Anil

Extraction of underground coal or mineral by the caving methods leads to surface deformations and the accurate measurement of this deformation is becoming a demanding task. Thus, the study demonstrates a Persistent Scatterer Interferometric Synthetic Aperture Radar (PS-InSAR) technique for surface subsidence measurement. The method was applied to measure the subsidence level over three mechanized depillaring panels with caving at GDK-11 Incline mine, India. The study was conducted using C-band data of Sentinel 1A/B sensors, which captured the data in the descending path from October 25, 2017 to March 07, 2020. The deformation level was measured based on the identified PS points in the specified region. In this case, 12 zones were identified (4 for each panel), based on the observation of permanent scatterer (PS) points. The maximum subsidence level and deformation rate range in 12 zones are −43.12 to −65 mm and −73.8 to 100 mm/year, respectively. The deformation level obtained through the PS-InSAR technique showed a good agreement with those of the field measurement. Thus, the PS-InSAR technique can detect and monitor the subsidence level over the goaved-out panel(s) of an underground mine using C-band SAR data of the Sentinal-1A/B sensor.

Mar 14, 2023

By Ryan Marsters, Adam Pring

The Rawah Ditch is a mountainous water supply diversion which supplies Larimer County, Colorado with water since 1903. The ditch includes two historic tunnels excavated by drill and blast through a gneissic rock buttress. Both rock tunnels were failing with annual convergence. After a snowshoe-accessed eld investigation, nite element modeling, and an alternatives analysis, a diameter DE pipe was inserted within each tunnel and the annulus lled. The proect was implemented in an Alternative Delivery contract lasting ve months from eld investigation through procurement and construction.

Jun 23, 2024

By Nikhil Dhawan, Shrey Agrawal

Feldspar, a low-alumina, and abundantly available aluminosilicate source, is explored in this study to extract aluminum and potassium values. The sample comprises lamellar layers of microcline and albite with quartz containing 17.4% Al2O3, 9.67% K2O, and 66.3% SiO2. Mechanical (milling) and thermal (alkali and acid baking) activation are investigated, followed by HCl leaching. The milling treatment up to 6 h is inefficient in phase dissociation and results in ~ 40% Al and K dissolution. The alkali thermal treatment yielded 80% Al and 71% K extraction. Direct precipitation of the dissolved Al and Si values yielded alumina purity of ~ 29%, and silica gelation separated SiO2 and improved alumina product (94% purity, 71% recovery). Acid baking yielded 98% pure alumina precipitate; however, Al and K extraction were limited to ~ 45% and 65%, respectively. The microwave-assisted alkali treatment was optimal with 800 W and 10 min processing conditions yielding 80% Al and 71% K recovery with 2.26 kWh/kg alumina of thermal energy consumption. The final product contains γ-alumina with a specific surface area of 87 m2/ g. Keywords Feldspar · Alumina · Potassium ·

May 18, 2022

High-pressure grinding rolls (HPGR) are an accepted, but continuously expanding, comminution technology. The copper industry has a growing need to process harder ores with progressively lower grades, more challenging metallurgy and increasing demand for efficient bacterial leaching applications. This has resulted in a major focus on HPGR use in a crushing circuit. If the industry is to increase leach extraction while lowering energy costs in high-throughput hydrometallurgical operations, HPGR will be of inherent significance. The following paper summarizes test work on copper leach ores utilizing the benefits of HPGR comminution, while increasing several critical metallurgical parameters. Based on the current work and previous investigations, it was found that HPGR comminution within a crushing circuit, in specific instances, can result in 2 - >10% increases in cop-per extraction. The tested variables are crush size, rock type and copper mineralogy dependence. Various other process parameters may also be optimized.

Jan 1, 2011

By J. F. Burr, D. Snyder, W. Calder

This paper provides a determination of the equivalent level of protection of the international standards relative to similar criteria used by the U.S. Mine Safety and Health Administration (MSHA) to approve two-fault intrinsically safe (IS) stand-alone equipment. U.S. mining law requires such a determination for MSHA to use alternatives to existing standards. The primary issue is to demonstrate that the international standards for equipment evaluation will provide at least the same level of protection for miners as the document currently used by MSHA.

Jan 1, 2018

By J. F. Burr, D. Snyder, W. Calder

This paper provides a determination of the equivalent level of protection of the international standards relative to similar criteria used by the U.S. Mine Safety and Health Administration (MSHA) to approve two-fault intrinsically safe (IS) stand-alone equipment. U.S. mining law requires such a determination for MSHA to use alternatives to existing standards. The primary issue is to demonstrate that the international standards for equipment evaluation will provide at least the same level of protection for miners as the document currently used by MSHA.

Jan 1, 2017

By D. J. McCracken

During 1995, the estimated consumption of lithium minerals in the western world was 139 kt (153,000 st).This amounted to 18 kt (20,000 st) of lithium carbonate equivalent (LCE). Overall tonnage demand for lithium minerals increased by 10.8 kt (11,900 st) during 1995from 1994. From 1992 to 1995, overall tonnage demand has increased 62%, from 85.5 to 139 kt (94,240 st). There are four major producers of lithium minerals. Gwalia Consolidated in Western Australia is the largest producer of spodumene. It supplies high-grade spodumene concentrate, fine-spodumene concentrate, glass-grade spodumene and chemical-grade spodumene.Tantalum Mining (Tanco) of Manitoba, Canada, produces high-grade spodumene concentrate, fine-spodumene, concentrate and montebrasite. Bikita Minerals in Zimbabwe is the largest manufacturer of petalite. It supplies high-grade and container-glass petalite.

Jan 1, 1996

By T. W. Camm, J. C. Johnson

"Most engineers are bright, hard-working, reliable, and prefer to avoid conflict. An engineering curriculum tends to self-select these characteristics. By most standards, you would expect workers exhibiting these traits to require minimal supervision. But is this true? Is this how most current engineering managers lead? Looking at some current theories on leadership combined with personal anecdotes, this presentation will look at some common misconceptions about leading engineers. INTRODUCTION Engineers are different. There, I said it. From cartoons to movies to television shows and more, there is a reason stereotypes of engineers resonate. Yes, you can find a lot individual variation among specific engineers that you may know, but they do not detract from some of the overarching commonalities that engineers are known for. CLASH OF CULTURES What distinguishes a professional? Raelin (1985), in his book Clash of Cultures, describes professionals as having superior intellectual training, maintaining their own standards of excellence, and being supported by associations that maintain the quality of the profession. Engineers obviously fit all three of these ideas: an engineering degree is still regarded as one of the most difficult to attain; we maintain our own standards both through peer-review and in academia through ABET accreditation; and through professional associations like SME to promote the discipline and foster technical growth. Six characteristics representing professional status are described by Raelin (1985, p. 9): Expertise—prolonged specialized training in a body of abstract knowledge. Autonomy—the freedom to choose the means to solving a problem. Commitment—Primary interest is in pursuing the practice of one’s own chosen specialty. Identification—identifying with the profession and with fellow professionals, both through formal associations and through peers external to the organization. Ethics—providing service without concern for oneself or without becoming emotionally involved with the client. Standards—committed to help in policing the conduct of fellow professionals. Engineers are smart—in the vast majority of cases they are hired specifically for their expertise. At a typical mine the ventilation engineer knows more about mine ventilation than anyone else on site; the same is true for the rock mechanics engineer, the explosives engineer, the planning engineer who uses sophisticated computer software—each is the expert for their particular area at the mine, that is why they have that responsibility. This can present a dilemma for the manager for each (sometimes all) of these engineers. The manager needs to keep everyone on task and focused on the objectives of the organization. Because they have reached their position by following the norms and expectations of the organization, managers tend to have a certain amount of loyalty to that organization. Engineers, on the other hand, tend to have mixed loyalties, having as much loyalty and affinity for their profession as they do for the particular company they happen to be working for at any given time. This dynamic can often lead to power struggles between the managers, based on their positional authority in the organization, and the engineers, based on their specialized knowledge (Camm, 2013)."

Jan 1, 2017

By M. Fan, A. Hobert, W. van Dyk

Low flotation recovery and selectivity have been long-standing problems in the treatment of most ultra-fine phosphate ores. This paper investigates the improved flotation of two ultra-fine Brazilian phosphate ores from Itafos’ Arraias project. These ores are predominantly composed of quartz, muscovite, apatite and a Ca-Al phosphate. As a result of fine phosphate dissemination and associated grinding requirements, column flotation was selected for the metallurgical test program to address the inherent limitations of fine particle flotation using conventional flotation cells. Accordingly, both benchtop Denver cell and laboratory column flotation tests were conducted to optimize their respective flotation responses. Improved flotation performance was achieved using column flotation as compared to benchtop mechanical flotation. In column flotation, a P2O5 concentrate grade of 30.5-31.0% was yielded at a flotation recovery of 83.7-85.1% for the 38x0µm generated ultrafines. The benefits of Eriez’ column flotation technology realized from this study include a higher degree of selectivity, increased recovery, and reduced collector dosage as compared to bench-scale mechanical flotation.

Mar 2, 2022

By A. Kosiór

Many remnants of gold exploitation in the Middle Ages were found in the Lower Silesia region. The oldest evidence of such activity was found in the neighborhood of Zloty Stok and comes from the 7th century. Mining of precious and non-precious metal ores has a great relevance in the late Middle Ages when advanced metallurgic technologies were mastered, that allowed to obtain gold, silver, lead, copper, zinc and arsenic from complex ores occurring in the oldest middle part of Sudetes. Historically it concerned the area of the Swidnica Principality and Klodzko County. Experience obtained in Freiberg, which is located close to the Lower Silesia, was used in the development of mining. A high level of mining and metallurgic technology was obtained in the 15th century that caused significant increase of production of the metals mentioned above. Unfortunately, the good time of Lower Silesian mining lasted only up to the 18th century; the notion of preservation of cultural heritage was unknown at that time. The Lower Silesian medieval mines were not in such a fortunate situation as the ?Wieliczka? and ?Bochnia? mines, which are operating to present-day, and which made preservation of the most interesting headings and objects possible. All these objects are now available for visitors. However, in the case of the middle Sudetes it seems that it is often sufficient to localize old shafts and headings on the basis of careful observations and old maps and carry out some earthwork to uncover medieval headings and objects of underground mining activity. They are often preserved in amazingly good state; this also pertains to mining devices. Another issue is of course the permanent preservation of that heritage and its possible availability for re-searchers and tourists. Some success has been achieved in that field (Zloty Stok Gold Mine is a good example), but also problems were encountered in many cases. The Lower Silesian Coal Basin, which has not been exploited for 10 years is an evidence that there is not a holistic conception of mining heritage renovation. Many attractive mining objects disappeared irrecoverably from the mountainous landscape of the Middle Sudetes despite common consciousness of their significance for cultural development of Silesia and other regions.

Jan 1, 2006

By P. L. Crouse, S. J. Lubbe, M. J. Kabangu

A selective extraction and separation of zirconium by solvent extraction with 1-octanol is proposed. The process is based on the dissolution of the metal basic carbonates in hydrochloric acid in the presence of potassium fluoride, using 1-octanol as extractant. The effect of several process parameters, including hydrochloric acid and potassium fluoride concentrations, reaction time, and phase ratio between the aqueous and the organic phase was investigated. Zirconium is enriched in the organic phase. The best extraction and separation results were obtained with the basic carbonate dissolved in 10% hydrochloric acid and 1.5 M potassium fluoride. The optimum reaction time was 15 min with an organic to aqueous phase ratio of 2:1. Based on the selectivity of zirconium over hafnium in the organic phase, a McCabe-Thiele diagram was constructed. A near complete stripping of zirconium from the organic phase was achieved using a 3 M sulphuric acid solution. Additional studies are required in order to determine the reaction mechanism and the chemical speciation of the current investigation.