Search Documents

By R. J. Davidson, V. Veronsee

Some of the parameters affecting the elution of gold from freshly loaded activated carbon using pure water as an eluant were studied. The procedure involved pretreatment of the gold-loaded activated carbon with a strong reagent of sodium cyanide and sodium hydroxide, followed by elution of the gold with water. Gold-loaded carbon obtained from three different sources was studied. It was shown that the elution temperature was the most critical parameter, and column operation at I !OCC (gauge pressure of 50 to 100 kPa) is suggested. The effects of variations in the concentration of sodium cyanide required for the pretreatment of loaded carbon and of variations in elution flowrate were also investigated. Both these parameters were found to have only a marginal effect on the efficiency of gold elution. The investigation also indicated that gold-elution rates were affected to a considerable degree by the particle size of the carbon concerned. Higher elution flowrates could be used when carbons of finer particle size were eluted. A modified eluate-collection procedure was also developed during the course of the investigation. Oven-drying of the loaded carbon was shown to have little or no effect on the efficiency of the subsequent gold elution. The calcium and silica contents of the various carbon samples were also determined. It was immediately evident that the calcium content was very considerable in the case of loaded carbons originating from carbon-in-pulp operations. Calcium concentration was particularly high where air agitation had been employed in the carbon-contacting circuit. To some degree, the calcium build-up explains the serious carbon fouling taking place, resulting in a decreased efficiency of gold adsorption. The fouling problem was found to be less severe when mechanical agitation was used. No poisoning by calcium carbonate was observed where the pregnant solution had been acidified before it was contacted with the carbon.

Jan 1, 1979

By P. C. Schutte, N. B. Strydom, A. J. Kielblock

Three groups of unacclimatized men were subjected to five-day climatic-room procedures at wet-bulb temperatures of 29,30, and 31 C respectively. The findings indicated that individuals reach a satisfactory level of heat acclimatization for work in environmental temperature conforming to those at which they were acclimatized. It is, therefore, superfluous to acclimatize men at wet-bulb temperatures that exceed those at which they are destined to work. These methods of acclimatization can be linked advantageously to heat-tolerance testing at mines with suitable underground temperatures.

Jan 1, 1983

By L. C. Woollacott

Some of the factors that may influence the reliability of a consistent material balance derived from plant data were investigated, data taken from a sampling of the Iow-grade tin-flotation circuit at Rooiberg A Mine being used as the basis for the investigation. The importance of subjecting a calculated balance to a thorough analysis of its sensitivity to erors in assay and flow rate measurements is highlighted. Several simple guidelines are derived from the analysis of the Rooiberg data, and these appear to be generaly applicable to process-evaluation exercises and to the technique used for the smoothing of material balances.

Jan 1, 1987

By A. B. Stewart, I. J. Barker

Traditionally it has commonly been believed that the only problem with inductive reactance in a submerged-arc furnace is that it leads to difficulties with the electricity supply as a result of the Iow power factor. This paper sets out to show that inductive reactance can also give rise to the following problems in the metallurgical operation of a furnace: (i) dead and live phases (fairly well known in openarc furnaces), (ii) lack of sensitivity to electrode movement, (iii) interactions between electrodes. These problems increase with increasing inductive reactance relative to resistance, and thus they increase with furnace size. Each of these effects is discussed in detail, and suggestions are made for their alleviation.

Jan 1, 1980

By M. B. Algeo

Discussion of the above paper M. B. ALGEO The management and staff of Buffelsfontein Gold Mining Company Limited are to be congratulated on the excellent performances described in the paper presented by Mr Christos. In this day and age, with the current economic and labour situation, the mining industry is being constantly pressed to increase the productivity of ever-diminishing quanta of resources. Stress in rock The ISRM Symposium, 1976 is to be held in Sydney from 9th to 13th August, 1976. It is being organized by The Australian Geo. mechanics Society as a regional symposium of the International Society for Rock Mechanics. Thermal analysis The First European Symposium on Thermal Analysis will be held at the University of Salford on 20th to 24th September, 1976.

Jan 12, 1975

Reviewer: P.R. Janisch The progress of mining and metallurgy in Australia and their contribution to that nation's economy closely parallel those of South Africa. Australia's was the second of the three great gold rushes of the nineteenth century. It was centred on Bendigo and Ballarat in Victoria, and occurred in the 1850's, a few years after California's forty-niners. The California goldfield also gave birth to the now common term for a tabular gold bearing deposit-a 'reef'. Amongst the fortune-seekers were sailors who had jumped ship on hearing of the riches to be found on land. When the gold ran out, and with it the money, the sailors found themselves stuck on a reef'. But others, more canny, had accumulated the means to move on, and some came to the Transvaal on the news of the Barberton discoveries. One of them was George Harrison.

Jan 1, 1993

By G. A. Bezuidenhout

Lonmin Platinum installed a concentrated mode dual-alkali scrubber at the smelter in Marikana in 2002. The dual-alkali scrubber was the technology of choice at that time as a sulphur fixation plant, due to the perceived benefits of handling both the high SO2 concentrations of converter off-gas and the swings in SO2 concentration that are linked to Peirce-Smith operation. Owing to current and impending legislative requirements for air quality and waste, Lonmin is currently considering additions to the dual-alkali plant, but is also evaluating alternative technologies for sulphur fixation. This paper reviews the decision of Lonmin to install a concentrated mode dual-alkali scrubber and presents plant performance achieved. It also describes the important control variables and sensitivities of the plant, and the final product that is produced by the operation of the plant. The legislative requirement that drives the Lonmin technology evaluation is also discussed.

Jan 1, 2012

By M. I. Brittan

SYNOPSIS The key reactions of the copper segregation process have been studied with a view to establishing the kinetics of the system. The investigation was carried out using two refractory copper ores from the Zambian Copperbelt in a small-scale, fluidized bed, chloridization reactor. The rate of chloridization of the copper in the ores is compared with the rate of volatilization of the cuprous chloride produced and with the rate of reduction of the cuprous chloride to form segregated metallic copper. In conjunction with available data on the rate of production of hydrogen chloride in a segregation system and with due regard to the conditions applicable in a TORCO reactor, it is concluded that the chloridization reaction is the major rate limiting step of the process. Factors influencing the rate of this extraction step and aspects of its mechanism are examined. The findings have confirmed the validity of the existing theory of segregation and provide insight as to the viability of the system of reactions involved in the copper segregation phenomenon. Experimental results which relate to observations made in the course of TORCO plant operation and segregation studies are discussed.

By Wm. Bleloch

SYNOPSIS The feasibility of rejection of nitrogen from stack gas by recycling of top-gas with cold-blast 95 to 98 per cent oxygen is assessed. It is concluded that nitrogen could be removed to a level below 3 per cent of the stack-gas using recycled cleaned cold top-gas and 95 to 98 per cent oxygen produced by a single-column air separation plant with liquid-air reflux instead of liquid nigroten reflux. The partial pressure of carbon monoxide in the stack-gas could be doubled without top pressure and the deposition of carbon and reduction of iron oxides by the stack gas could be markedly increased. It is concluded that rate of stock descent could be doubled compared with present-day practice and an iron make of 4400 kg/m 2 of hearth area/hour may be attainable with a working volume of 129 m2/m hearth diameter by this method. Oxygen consumption is estimated at possibly 280 m2 (0.4 t)/t iron made and carbon consumption at possibly 280 kg/t iron. Power consumption for oxygen including auxiliaries is estimated at 304 kWH/t 100 per cent oxygen as 95 to 98 per cent gas. The air separation cycle due to Schuftan is discussed in some detail, and the components of a 1 600 metric ton/day separation plant are briefly discussed. The paper is a theoretical essay.

By P. Horrell, K. Rhodes, G. Harrison, J. Dean, D. Sammons, M. Stander

Anglo Platinum have perceived a need to increase the rate of reef development both for new mechanised stoping technology and on conventional new developing mines. The Research and Development Division of Anglo Platinum therefore initiated an experimental reef raise project with a tunnel boring machine (TBM) at Bafokeng Rasimone Platinum Mine (BRPM). The scope of the trial was for the boring of a reef raise 340 metres in length on the Merensky Reef. The boring phase of the trial took place over six months and the average rate of penetration of the TBM was 0,47 metres/hour. TBM utilisation was 22%. The TBM used in the trial was a Jarva MK6 manufactured in 1972 and its design with its backup system was not considered to be an ideal machine for reef development. However it was the intention of the trial to prove the concept of developing with a TBM on reef. In this respect the trial was unequivocally a success. There were many problems and long delays did occur during the boring phase. Nevertheless there is every confidence that a new TBM can be designed specifically for this type of work that will achieve high rates of advance up to (say) 400metres/month and with a more flexible steering system in order to negotiate reef changes. It can therefore be expected that TBMs will be used in the future for reef development on South African platinum mines.

Sep 1, 2001

By J. M. Musadaidzwa

Skorpion Zinc is located 25 km north-west of the small settlement of Rosh Pinah in southern Namibia. Commissioned in early 2003, Skorpion Zinc became the first mine-to-metal operation to commercially apply a purely hydrometallurgical process route to exploit a zinc oxide orebody. The novel technology, known as The Modified ZincexTM Process patented by Tecnicas Reunidas, comprises sulphuric acid atmospheric leaching, zinc solvent extraction (SX) and electrowinning (EW) to produce London metal exchange (LME) Special high grade (SHG) zinc. Forming the core of the process, the SX step has thrived in its role as a barrier to impurities and also in the upgrading of the pregnant liquor solution (PLS), converting it into a loaded electrolyte (LE) sufficiently rich and pure for EW. Against this successful run, a number of challenges have, however, been encountered in SX due the emergence of upset conditions largely emanating from upstream processes. This paper outlines some of the major deviations that have beset the SX process in its first five years of continuous operation. Impurity excursions, temperature depressions, changes in phase continuity, excess aqueous entrainment, the effect of colloidal silica and the accumulation of rare earth elements on the organic phase will be discussed in detail. Keywords: skorpion zinc, solvent extraction, the Modified ZincexTM Process (MZP) DE2HPA, aqueous entrainment (AE), loaded electrolyte (LE), standard liquid validation (SLV) test, organic continuity, aqueous continuity (AC), electrowinning, colloidal silica, phase disengagement time (PDT), rare earth elements (REE).

Jan 1, 2009

By M. L. Young, J. B. See

Effective thermal conductivities of packed beds of chromite ores by M. L. YOUNG, B.Se. (Rand), M.Sc. (Rand) (Visitor) and J. B. SEE, B.Sc. (Hons), Ph.D. (New South Wales), M.I.M., M.I.M.M. (Member) The effective thermal conductivities in stagnant air of packed beds of fines, lumps, and indurated and pre-reduced pellets of two chromite ores with different chromium-to-iron ratios were determined in the temperature range 300 to I 100°C by the heat-sink technique. Packed beds of fines, whether of the size fraction between 20 and 65 mesh, between 65 and 100 mesh, or between 100 and 150 mesh, were found to have the same values of effective thermal conductivity. For one ore, the effective thermal conductivities of packed beds of fines between 20 and 48 mesh at tem peratures above 600"C were higher than those for finer particles. This difference is explained as being due to the increase in importance of radiation heat transfer, but no definite conclusions are reached about the relative contributions of conduction and radiation heat transfer to the effective thermal conductivities of packed beds of fines between 20 and 48 mesh. Two published models were used for the theoretical prediction of values for thermal conductivities of the indurated and pre-reduced pellets as well as of lump ore. The experimental and theoretical results were in good agreement in view of the uncertainties in the assumed values of emissivity and thermal conductivity of the chromite ore.

Jan 12, 1976

By Anthony K. Anyimadu, Chris M. Rule

Froth flotation is the primary mineral processing separation step employed in the beneficiation of PGM ore bodies. Anglo Platinum operates a significant portion of the total installed flotation capacity in the PGM industry, which is installed at 20 operating plants across the Bushveld. PGM flotation has undergone a considerable evolution in both the capacity of flotation cells employed as well as in the circuit design configuration over the past thirty years. Certain of Anglo Platinum?s flotation circuits have been in operation for a relatively long period of time, (in some operations installed equipment dates from the 1960?s) and this allows comparative operating performance between various equipment types and circuits to be evaluated. This paper summarizes some aspects of this experience. Research trends in flotation are continuously monitored to incorporate appropriate findings into existing and future circuit designs. Continuous evaluation and monitoring of flotation performance is undertaken to identify opportunities for increasing flotation efficiencies. Mineralogical and fractional analyses of plant composites and survey samples are analysed to interrogate speciation and association data. This analysis has enabled a better understanding of priorities and opportunities for improved metallurgical performance. These opportunities are divided into three improvement areas: stability, liberation, and fines flotation. The paper discusses these, as well as the circuit design improvements required to take full advantage of the opportunities identified.

Jan 1, 2007

By A. H. Swart, M. F. Handley

Unplanned stope panel collapses occur on most near-surface and shallow mines in South Africa. Although these incidents often occur during blasting, they pose a major threat to the safety of underground workers and the economic extraction of orebodies. Most stope panel collapses occur due to excessive panel lengths that are not designed according to a systematic design procedure or methodology. Instead, panel lengths are often dictated by the equipment in use and by previous experience under similar conditions. Hence, a rock engineering design methodology for the design of stable stope panels between pillars is of vital importance for optimum safety and production in shallow mining operations. Using the proposed design methodology described in this paper, rock mechanics practitioners and mine planners should be able to identify and quantify the critical factors influencing the stability of stope panels. The critical factors should then be used as input to the design of stable stope panels that will provide the necessary safe environment for underground personnel working in stopes. The proposed design methodology is an iterative process, which includes aspects such as rock mass characterization, estimation of rock mass properties, identification of potential failure modes, consideration of appropriate stability analyses and other elements of the rock engineering design process. This process continues after implementation. During monitoring, new data should be included in the database and the design process repeated on a regular basis. Design approaches included in the proposed design methodology include empirical methods such as different rock mass classification methods, analytical methods such as elastic and Voussoir beam analyses, kinematic analyses, probabilistic analyses, and numerical analyses. Keywords: stability, stope panels, design methodology, hard rock mines, shallow mining operations

Jan 1, 2004

Jan 1, 1981

The 95th Annual General Meeting of the South African Institute of Mining and Metallurgy was held in the Gold Room of the Transvaal Automobile Club in Johannesburg on Wednesday, 12th August, 1992.

Jan 1, 1992

The International Colloquium on Developments in Froth Flotation, which replaced the Annual University of Cape Town (UCT)/University of Stelenbosch (US) Minerals Processing Symposium, was held at the Van Riebeeck Hotel in Gordon's Bay on 3rd and 4th August, 1989. The Colloquium attracted 150 delegates from the mining, metallurgical, and chemical industries, including 9 from overseas.

Jan 1, 1989

By R. H. O?Connor, B. N. Soutar

The paper reviews the introduction 01mechanical shaft drilling into the sinking 01shafts in the Gold Fields Group. A comparison is made between the operating costs 01the drilling rig and those of conventional hand-held machines, and it is concluded that, despite certain disadvantages, mechanical drilling is preferable.

Jan 1, 1988

By J. A. Drummond

The duties and efficiencies of a number of main and auxiliary fans were determined by standard and thermal methods. Some observations on the effect of water and dirt accumulation on fan performance were made.

The 94th Annual General Meeting of The South Mrican Institute of Mining and metallurgy was held in the Gold Room of the Transvaal Automobile Club in Johannesburg on Wednesday, 14th August, 1991. Obituaries The President announced the deaths of the following members of the Institute: Honorary Life Fellow and Past President

Jan 1, 1991