Search Documents

By Duane A. Houkom

Explosive demolition of concrete has been accepted as a safe and economical means of concrete removal for many years. I imagine that the early concrete blasters were experienced rock blasters who applied their knowledge to just another formation. Since a concrete foundation is generally located in a congested area, the owner is willing to accept the higher costs of mechanical removal,rather than promote "a new idea" to his management. This attitude is rapidly changing,making it possible to use the advantages of explosives in more congested locations.

Jan 1, 1982

By Theodore C. Hile, Floyd P. Henry, Ken Gragg

"Conventional explosive-storage methods usually rely on combinations of earth and concrete barriers, along with sufficient distance between limited explosive loads, to avoid accidental conflagration. However, under many circumstances, Air National Guard (ANG) facilities co-located with civilian airfields have trouble meeting necessary Quantity-Distance (Q-D) requirements for Explosive Hazard Class/Division 1.1 and 1.4 materials. Because of the danger posed by explosives stored in earthcovered magazines (ECMs) too close to civilian activities, ANG units often find itdifftcult to maintain adequate stores of ordnance needed to meet unit mission goals."

Jan 1, 1999

By Stanley L. Lippincott

A number of Federal and State agencies require formal training for blasters. Federal agencies often specify the need for initial training involving all job responsibilities as well as periodic refresher training to assure adherence to current operating procedures. failure to provide and document such training can result in substantial penalties.

Jan 1, 1995

By Marlyn G. King, Robert L. Martin

Blasting activities in all four pits at Thunder Basin Coal's Black Thunder Mine are focused on cast blasting. With widths varying from 190 feet to 265 feet and bench heights varying from 90 feet to 175 feet, casting efficiencies vary with different geometry's. For example, the percent cast to final in the 200 foot pit is on the average higher than the 270 foot pit. The powder factors are somewhat higher in the narrower pits, thus increasing the cost of blasting. This leads to a very detailed look at the actual benefit of cast blasting and the associated cost of these benefits.

Jan 1, 1995

By Karl E. Burgher

Accidental explosions occur throughout the world. They can happen at chemical plants, fireworks plants, grain depots, or as a result of collisions involving volatile or hazardous chemicals. It is interesting, as we know as blasters, that we can take two very harmless products and mix them under certain conditions and produce a violent explosion. It is often very difficult for the investigator to determine the magnitudes of blasts after the fact. However, an estimate must be made to settle vibration and airblast damage claims. The blasting consultant or technical representative is often called upon to act as an expert to mitigate these claims.

Jan 1, 1993

By Frank Wilder, Mark Ferrero

One of the challenges currently facing the explosives industry is how to transition its workforce and its business systems to respond to the increasing pressures for improved inventory and records management. The pressures applied by many U.S. federal and state agencies, such as the Bureau of Alcohol, Tobacco, Firearms and Explosives (ATF) and the Department of Environmental Protection (DEP), as well as regulatory agencies around the world, are increasing the need for accurate inventory accounting of explosive materials and blast documentation. With blasting companies now facing regular documentation audits, potential liability issues may arise due to the inconsistent or missing documentation.

Jan 1, 2006

By Kenneth Eltschlager

Post-blast assessment techniques using off-site data which includes location, seismograph and photographic data were discussed during the Blaster’s Weekend at this year’s ISEE Conference. Blast and property locations with commonly available GPS units allow for the spatial relationships surrounding the blasting to be documented. When distances are coupled with the charge weight per delay, the scaled distance can be calculated to any structure for either compliance with the rules, or to project limitations. When blasting seismograph data is obtained, the scaled distances are then able to be plotted against ground and air vibration levels for post-blast assessment purposes.

Jan 1, 2007

By Pierre Mousset-Jones, Jaak Daemen, Songlin Zhang, Jon Hurley

Most western United States open pit gold mine ore bodies are disseminated deposits. The mineralization is so irregular that it is difficult to visually identify the ore/waste boundary. Blast hole samples are used to interpolate digging polygons based on the pre-blast position of the bench. Dilution caused by blasting is of major concern at these mines, since blast movement can mix and dilute the ore and move it beyond flagged digging polygons established on the blasted rock according to their pre-blast location. Typically, mines try to reach a compromise between blast fragmentation and movement.

Jan 1, 1994

By K. G. Holley

Blasting is usually required to produce easily-excavated broken rock, while leaving surrounding rock masses as undamaged and stable as possible. In mining applications, it is common to utilise production blasting in the centre of an open pit, and specially developed limits blast designs when blasting adjacent to the excavation perimeter. In open pit blasting, limits blast designs generally include pre-splitting, trim blasts, or buffer blasts, all of which are designed to limit, or eliminate, damage beyond the designed pit wall. This paper reports on the findings of a study of the profile of damage in rock masses surrounding blasts, determined by a combination of vibration monitoring, displacement monitoring using extensometers, and video inspection of open holes drilled at various distances behind blasts. The results obtained suggest that the profile of damage may extend for the full depth of the bench, for distances of up to 12 to 15 metres behind blasts. This suggests that entire berms may be affected by blasting, displaying loss of friction and cohesion along joint and fracture planes. The study has considered production blasts and trim blasts with small diameter blastholes and pre-splits.

Jan 1, 2004

By Thomas M. Keevin, Gregory L. Hempen

A study was conducted to measure underwater pressures associated with confined borehole shooting used to remove rock for The Kill Van Kull Deepening Project, U.S. Army Corps of Engineers, New York District. A major natural-resource-agency concern was the potential for fish mortality during explosive rock removal. Currently, fish mortality models are based on testing programs that exposed captured organisms to open-water blasts. Natural resource agencies, without in-house explosive engineering expertise, generally are not familiar with the physical properties of blasting underwater. Confined shots are most often used for demolition and rock removal underwater. Pressure amplitudes from confined blasts are significantly reduced as compared to open-water blasts that, are commonly used for fish testing The duties of natural resource agencies are made even more difficult by the lack of published data on pressures associated with confined blasting. As a result, explosive weights for confined shots mistakenly have been used to run mortality models that were developed using open-water blast pressure data. This study was conducted to collect pressure measurements during rock removal for the KVK deepening project and compare those data with computed peak pressures for open-water explosions.

Jan 1, 2005

By Mark S. Stagg, Steven V. Crum, Stephen A. Rholl

As part of its ongoing research concerning rock fragmentation by blasting, the Bureau of Mines has undertaken a series of test blasts where six cylinder-shaped pieces of granite rock were fragmented using high explosives. The tests were intended to: 1) Establish a dataset that could be used in the development and verification of theoretical models that simulate rock blasting and 2) To add to the fragmentation data currently being collected by Bureau researchers. The cylindrical geometry was chosen so that the fragmentation could be directly compared to two-dimensional computer simulations that assume an axisymmetric configuration as well as more sophisticated three-dimensional models. The granite cylinders, Carnelian granite and Charcoal granite, ranged in size from about 0.46 meters (18 inches) to 0.58 meters (23 inches) in diameter by 0.91 meters (36 inches) to 1.52 meters (60 inches) in length. Physical rock properties tests performed on the Charcoal granite cylinders indicated that the rocks did in fact have similar physical characteristics. PETN-based detonating cord and dynamite were used as the explosive charges and estimates of the values of some important physical properties are given. For the first five tests, the blasted rock was contained by a heavy rope mat suspended inside the Twin Cities Research Center's blasting shelter. The fragments from each of these shots were sorted and weighed to determine the corresponding fragment-size distributions. Even though different types of granite and cylinder sizes were used, similar fragment distributions were produced from shots that used a similar explosive, in this case the PETN-based detonating cord, and comparable burden-to-charge diameter ratios. Significantly coarser fragmentation was produced from a blast that used dynamite as the explosive charge. Fragment velocities were calculated using photographic data from the sixth test which was shot unrestrained in a quarry and filmed with high-speed cameras.

Jan 1, 1990

By Larry Mirabelli, Gerard J. O'Brien

"The construction of the Third Harbor Tunnel is a key element of the Central Artery TunnelProject. The tunnel is to traverse Boston Harbor directly linking South Boston to EastBoston. The tunnel is a cut and cover tunnel as opposed to a bored tunnel. The cutdimensions are 95' wide, 110' deep and approximately 4000' in overall length."

Jan 1, 1993

By Michael S. Stern, Gordon P. McDonald

The increasing costs and problems associated with transporting and safely disposing of used engine oils from remote mine sites have caused mining companies to consider other ways to consume their used oil. One practical method of disposing of these used oils is to blend them with the diesel component of ANFO and Heavy ANFO type explosives.

Jan 1, 1993

"In order to increase control over blasting, it is important to identify the imperative mechanismsand to quantify their participation during the rock fracturing process. The useful energyreleased by the detonation of an explosive is split into shock and gas energies. The relativeimportance of these two energies in the rock fracturing process is still an area of active debate."

Jan 1, 1999

By John S. Manka

Of the various methods used to reduce the density of emulsion explosives prior to detonation; ammonium nitrate prill addition, glass micro-balloon addition and chemical gassing, chemical gassing is the method most often selected by emulsion explosive end users. Chemically gassing emulsions costs less than adding micro-balloons and chemically gassed emulsions have better water resistance than emulsions that add ammonium nitrate prills to reduce the bulk density. Unfortunately, the chemical gassing of emulsion explosives can be intricate and is often more art than a science. To gain a better understanding of chemical gassing, we investigated the factors that may affect the chemical gassing of emulsion explosives. Variables investigated as having an effect on gassing were the pH of the oxidizer phase, the amount and type of nitrogen in the emulsifier, the composition of the oxidizer phase, the use of pH buffers in the oxidizer phase, and how the gassing reagents are added to the emulsion.

Jan 1, 2004

By Lewis L. Oriard

Near the village of Villarino de los Aires, in the province of Salamanca, Spain, was an existing underground hydroelectric power plant. A major enlargement was undertaken to increase the electrical generating capacity, under a contract awarded to a joint venture of Dragados y Construcciones, S. A. (Spain), Entrecanales y Tavora, S. A. (Spain), and S. A. Conrad Zschokke (Switzerland). The enlargement required the excavation of a large and complex underground system of tunnels, shafts and chambers adjacent to existing facilities and interconnected with these facilities. The existing machine hall and transformer chamber were both extended, requiring the blasting of the existing end walls. The drilling, blasting and excavating of the underground system had to be done without damage to existing underground chambers and tunnels, or any of the existing structures, equipment or instrumentation facilities, often within just a few feet of the blasting. This required careful control of vibrations, airblast overpressures and dust.

Jan 1, 1997

By Edward Jr Walter

This paper discusses the problems that arise in the process of developing adequate explosives noise legislation. Case histories are used to illustrate how and where these problems arise and the course of action followed in overcoming them. It is imperative that those concerned keep informed as to possible legislation and be prepared to present solid facts that will insure fair and reasonable controls.

Jan 1, 1975

By Richard J. Mainiero, Marcia L. Harris, James H. Rowland

In the past several years, there have been a number of blasting-related carbon monoxide migration incidents. In each case, there have been some common factors that appear to be related to carbon monoxide migration. Geology, heavy confinement of the blast, close proximity to the affected structure, and open pathways into the affected structure are just a few. Prince William County, VA is an area undergoing a boom in suburban development. In the year 2001, more than 4,050 new homes were constructed within the county.1 In the new housing development located in Bristow, VA, trench blasting was utilized to excavate proposed sewage and utility lines. On November 8, 2002, a trench blast was conducted for the installation of utility lines. Later that evening a carbon monoxide detector alarmed in a nearby house. The gas company and fire department sampled for carbon monoxide and measured 100 ppm and more than 200 ppm on the first floor and in the basement respectively. Subsequent efforts to prevent migration of CO into the nearby homes met with mixed results. The only reliable technique for protecting neighbors from CO appears to be the placement of CO monitors in the homes. The events are presented and discussed.

Jan 1, 2004

Computational techniques in determining particle size distributions after blasting is getting wide acceptance. A well known approach to extract this kind of information from digital images is edge detection. The number of edge points on a given image increase proportional to the increase of the particles on the image. By selecting a conveniently smooth threshold, counting the signed edge pixels may be a suitable metric further used to quantify the number of particles in the image. Here we propose an image processing algorithm together with Adaptive Neuro Fuzzy Inference System (ANFIS) to efficiently count the rock particles with various sizes on a given surface. To determine a suitable approximation for a mapping between the number of edge pixels and the number of particles, ANFIS is a suitable tool. As a trainable classifier ANFIS proved itself as being better efficient approach than other well known multilayer perceptron classifiers. ANFIS is trained by using convenient training data pairs previously experienced from empirically counted sample images. When given a new image containing the particle information of selected surface, the hybrid neuro fuzzy image processing approach provides satisfying performance on counting the correct number of particles up to the given scale of sizes. In this paper an experimantal study for assessment of particle size using ANFIS is presented.

Jan 1, 2004

By Sehoon Lee, Duhwoe Jung, Eunsu Cha, Kyeonghwan Jeong

This case study presents the effectiveness of underground rock blasting to facilitate the trench cut in the hard rock layer using a conventional trench cutter for the construction of a diaphragm wall. Rock blastings are pre-performed up to the scheduled depth and then the fragmented rocks can be easily cut using a conventional trench cutter. Two trial underground rock blastings have been performed and the effectiveness of pre-blasting is presented in terms of a cutting rate, a loss of cutter heads and an amount of overbreak. Based on the results obtained from the trial underground rock blastings, the following conclusions can be appropriate: 1) A pre-blasting of hard rock layer located in depth can help to overcome the limitation of the trench cut using a conventional trench cutter. If the hard rock layer is fragmented after blasting, the fragmented rocks can be easily cut using a conventional trench cutter, 2) The speed of cutting works was accelerated and the loss of cutter heads was significantly reduced in the sections where the blastings were applied prior to cutting. 3) The amount of overbreak, expressed in terms of the amount of poured concrete, can be reduced to some extent. However, the location of blast holes in the trench can also contribute to the amount of overbreak. The closer the location of blast holes to the edge of the trench, the more extensive fractured and cracked zone can be formed on the face of the trench. This can increase the amount of overbreak if the trench is left empty for a while.

Jan 1, 2000