Search Documents

By Abolfazl Eslami, Fatemeh Rostami, Sara Heidarie Golafzani, Mohammad Arabameri

Collapsible loess is classified as problematic soil found in most continents. The loess immediately collapses under stresses induced by axial compressive loading or the soil weight when exposed to moisture. In Iran, vast areas of the Golestan province are covered with aeolian loess deposits. This paper investigates whether the simultaneous effect of inundation and pre-loading in helical pile installation are operative and effective in improvement of Golestan loess. The effect of installation conditions on loess collapsibility is studied via two main approaches, i.e., field investigations and physical modelling. The experimental studies include installation of eight single helix piles in the Amirkabir University of Technology Frustum Confining Vessel, i.e., FCV-AUT. Also, four single helix piles with embedment depth of 3 m and diameter of 250 mm were installed in Golestan province and full-scale pile static loading tests were performed. The results indicated that the simultaneous application of crowd loading and water pressure during installation of helical piles results in better soil shear strength parameters. Moreover, high crowd stresses or low crowd stresses accompanied by water pressure during pile installation brings about similar load-displacement behavior of model piles installed in FCV-AUT and full-scale helical piles.

Oct 1, 2022

By David S. Graham, Joseph D. Bailey, Paul J. Axtell, Michael K. Muchard

"Two instrumented test piles were simultaneously subjected to a static lateral load test by jacking the piles apart. One of the piles was loaded in axial compression via kentledge during the lateral load test. Both piles were constructed in an identical manner. These piles were constructed and tested as part of a construction-phase load test program for a floodwall improvement project along the Missouri River in Kansas City, Kansas. Details of the subsurface conditions, drilled pile construction, instrumentation, and load testing procedures are described. Data collected during testing of the piles are presented and compared. Potential effects of the axial compressive load related to observed differences in pile lateral response are discussed.INTRODUCTIONTwo instrumented test piles were simultaneously subjected to a static lateral load with one of the piles also subject to a combined axial load during testing. The load test program was part of a floodwall improvement project in Kansas City, Kansas. Known as the BPU floodwall, the floodwall runs along the south bank of the Missouri River at a Kansas City Board of Public Utilities power generation and water treatment facility. The project location is shown in Fig. 1.Drilled, 2-ft (610-mm) diameter piles were designated by the designer, the U.S. Army Corps of Engineers (COE), as the foundation type for supporting extended floodwall footings. The drilled piles are fully cased, cast-in-place concrete, reinforced with a steel 12x74 (310x110) H-pile. In order to test soil lateral response and pile structural response under combined loading, the COE required that both a lateral test and combined lateral and axial test pile be constructed and tested. In order to most efficiently test both piles and to allow for simpler comparison, the two piles were simultaneously laterally loaded by jacking the piles apart, applying a maximum lateral load of 195 kips (867 kN). A constant axial load was applied to the combined test pile by kentledge prior to lateral loading and was maintained for the duration of the lateral load test. The total weight of the kentledge was 61.5 kips (274 kN). Fig. 2 shows the test setup."

Jan 1, 2017

By Andrew Cushing

This paper presents the design and construction of the foundation for a major high-rise real estate development on the west side of Manhattan. Arup was retained by Underpinning and Foundation Skanska to design a secant pile wall as excavation support for a proposed two-level basement of a new 23-story residential building located at 100 11th Avenue and West 19th Street. The secant pile wall will also act as the permanent basement retaining wall for the new building. The site is bounded on two sides by existing structures and is underlain by a thick deposit of very soft organic silt and clay. Therefore, the potential for ground movements and their impact on an adjacent structure bearing on shallow footings were of the utmost concern. This paper addresses the design and construction considerations associated with this secant wall, as well as installation details. Measured wall movements are also used to assess the validity of the pre-construction soil strength and stiffness design parameters.

Jan 1, 2008

By Scott M. Mackiewicz

This project includes replacement of the historic vertical-lift span Meridian Bridge (U.S. Highway 81 over the Missouri River) that connects Yankton, South Dakota with rural Cedar County, Nebraska. The new 76-foot wide, 1,590-foot long steel plate girder structure required the use of drilled shaft foundations that extended into the underlying Carlile Shale formation. Designers indicated that an individual drilled shaft capacity of about 2,000 kips will be needed at each of the river piers, and based on the subsurface information, 8 to 10-foot diameter drilled shafts extending to about 115-foot would be required for support of the bridge structure. An Osterberg Load Test was performed on one test shaft to determine the ultimate skin friction and end bearing of the Carlile Shale. This paper describes the design and installation of the load test drilled shaft as well as presents the load test results as compared with predicted design values determined using FHWA methods.

Jan 1, 2008

By Timothy C. Siegel, Paul J. Axtell

The Missouri Department of Transportation (MoDOT) recently replaced the Hurricane Deck Bridge that carries Highway 5 traffic across the Osage Arm of the Lake of the Ozarks in Camden County, Missouri. The former bridge was constructed in the 1920's and was supported on pneumatic caissons bearing on dolostone bedrock. The replacement structure is founded on drilled shafts socketed into the bedrock. During the design phase of this bid-build project, a baseline design was developed and Alternative Technical Concepts (ATC's) were allowed from approved contractors. Those ATC's were confidential and not shared between teams. Either the baseline design or the approved ATC design could be bid by the respective contractors. The baseline design included re-use of the 90-year old caisson foundations. Accordingly, an extensive evaluation of the caissons and underlying bedrock were conducted by coring, laboratory testing, acoustic tele-viewer (ATV), and cross-hole sonic logging (CSL) methods. The results of the investigation indicated the caissons were in excellent condition and suitable for re-use. However, a more cost-effective ATC was submitted, awarded, and constructed that did not re-use the existing caisson foundations but rather reduced the span lengths, increased the number of piers in the water, and supported those piers on drilled shafts. Interestingly, the difference in low bid price between the awarded ATC and the baseline design was less than one percent of the construction cost. This paper describes the multiple foundation designs that were necessary for this interesting project. The various foundation evaluations include the existing pneumatic caissons, large-diameter open-ended pipe piles to support the baseline design, and the design of rock-socketed drilled shafts that were successfully constructed in 2012.

Jan 1, 2017

By Michael D. Justason

This paper describes the technology behind the development of an automated energy control system for a diesel pile hammer. Some background is given on experience using an energy monitoring system on the Route 1/I-95 interchange in Alexandria, Virginia. An adjustable hammer throttle and feedback from an energy monitoring system was then used to create a fully automated hammer energy control system. The performance of this system is described in reference to a piling project in Canada where the automated energy control system was used to obtain an unprecedented level of quality control and assurance ? data and graphs from the project are presented. The hammer energy control system (ECS) was used to successfully control and maintain a prescribed impact energy for the diesel hammer. This paper presents the first ever results from a truly automated diesel pile hammer and points to a new direction in quality control and assurance in pile driving.

Jan 1, 2006

By Bill Zietlow

A micropile and soil nail underpinning system was installed to support a building immediately adjacent to a 25-ft deep excavation in downtown Salt Lake City, Utah. Both the building and the underpinning were instrumented to monitor deflections, rotation and crack growth. The underpinned structure consisted of a two story concrete masonry unit (CMU) building founded on shallow spread footings attached to a concrete high-rise building on spread footing two floors below grade. The face of the excavation was 10 in. in front of the underpinned building foundation wall. The underpinning system consisted of small diameter hollow bar micropiles installed with injection grouting techniques below the bottom of the excavation and attached to the underpinned structure by a concrete pile cap doweled into the existing footing. The lateral loads imposed by the soil under the underpinned structure were designed to be supported by the soil nail wall installed through the micropiles during excavation. The settlement monitoring instruments consisted of crack gages, optical survey prisms, high sensitivity vibrating wire water levels and biaxial vibrating wire tilt meters. They recorded maximum movements of approximately 0.1 in. of settlement, 0.05 deg. rotation (top of wall rotating away from excavation) and up to 0.08 in. of crack opening during the excavation until one month after the soil nails and shotcrete facing were completely installed. This movement was well within both the estimated settlement and the estimated settlement tolerance of the underpinned structure.

Jan 1, 2008

By J. K. Mitchell

Soil improvement is examined within the context of the characteristics of different soil types, the types of ground improvement techniques that can be used to improve them, and the level of improvements that might be achieved. Several case histories are described to show how the particular soil and foundation characteristics influence the choice and success of different ground improvement techniques. Although the basic methods for soil improvement have been known for many centuries, there have been significant recent advances in the technology for their use. Time effects following the densification of cohesionless soils may lead to significant improvements in strength and stiffness. Unanticipated chemical reactions may follow stabilization using admixtures when soils for which there has been little prior experience are encountered. In some cases foundations that combine features of both ground improvement and deep foundation systems may provide good performance at reasonable cost.

Jan 1, 2010

By Eric J. Pederson

The down hole hammer is widely used in specialty geotechnical construction. The common uses include tie-back anchor installation, micropile installation, and general soil/bedrock drilling operations. Veit used these techniques to develop a cost effective way of installing the foundation system for University of Minnesota Football Stadium. The soils present at the site of the stadium contained layers of concentrated cobbles and boulders. The geotechnical engineer recommended a driven pile system, and the base bid outlined in the project documents consisted of an H-Pile using a 14x73 pile section. Veit submitted an innovative alternate consisting of using a rotary percussion system to install a 12? O.D. pile. This paper will show that this pile type and installation method was the correct choice for the project. The design criteria for the compression, uplift, and lateral capacities and deflections were met, while eliminating pile damage. The method resulted in a significant cost savings to the University and maintained the project schedule.

Jan 1, 2008

By M. Hesham El Naggar, Tony Sangiuliano, Alper Turan

"Bridge abutments supported on pile foundations are often constructed over weak and compressible soils. The consolidation settlements induced by the embankment loads are known to result in downdrag and lateral forces on the piles supporting the bridge abutments. The performance of a pile group including inclined piles embedded in consolidating soils was investigated numerically considering surcharge loads from approach embankment construction. A two-dimensional numerical model was constructed using commercial finite element software PLAXIS and calibrated against field measurements of the abutment movements observed on Brookdale Avenue Underpass Structure located on the Macdonald-Cartier Freeway in Ontario between Cornwall and the Quebec border. The soft soil model (SSM) was used to simulate the constitutive behavior of the compressible soil deposit. The SSM model parameters were determined based on the laboratory tests. Subsequently, time dependant development of downdrag effects was comparatively evaluated for vertical and inclined single piles as well as a pile group that included both vertical and inclined piles.Results showed that drag loads increased with the consolidation time. However, majority of accumulation of drag loads took place within first 120 days after installation of piles. The results also indicated that the shear forces and bending moments are controlled by the lateral spreading of foundation soil and their accumulation is proportional to consolidation time. The large axial strains caused by large downdrag forces are considered to have yielded the piles and this is a possible reason for unusual abutment movements. The results presented in this study are considered to be of interest to researchers and practitioners.1. IntroductionDeep foundation units are widely used for supporting bridge piers and abutments, where weaker surficial soils preclude shallow foundations. Particularly in Ontario, semi-integral and integral abutment bridges are typically supported on end-bearing steel driven piles. The construction of approach embankments over weaker, compressible soils results in significant vertical and lateral soil movements, which induce additional loads on piles supporting the abutments. In order to minimize such effects, preloading and surcharging are commonly employed approaches to avoid unanticipated settlements prior to the installation of piles. Other alternatives such as aggregate pier supported approach embankment are also being studied as the schedule restrictions imposed by preloading and surcharging becomes cost prohibitive (Turan et al. 2012)."

Jan 1, 2015

By Glenn J. Rix, Eduardo Tavera, Raphael Siebenmann, Zhongjie Zhang, Robert C. Bachus, Jongwon Jung

"The Louisiana Department of Transportation and Development (LADOTD) uses a variation of the FHWA-modified Gates equation to verify the nominal pile bearing resistance, typically on smaller projects where static load tests and dynamic monitoring are not practical. An inconsistency in the resistance factors for load and resistance factor design (LRFD) penalizes the target pile capacity needed during field observation if the LADOTD dynamic formula equation is used, which is unreasonable, and has created confusion among designers, consultants, district personnel, and inspectors in Louisiana. The objectives of this project are to recalibrate the FHWA-modified Gates equation and update the associated LRFD resistance factor for pile types and local soil conditions encountered in Louisiana. Improved consistency relative to the current design approaches will be achieved if the updated resistance factor matches or exceeds the worst-case resistance factor used by LADOTD, which will reduce confusion among users. Updating the resistance factor will also serve to increase confidence in the FHWA modified Gates equation, optimize the efficiency of the piles, and reduce project costs.IntroductionThe original 1957 Gates pile driving formula (Gates, 1957) is an empirically derived dynamic formula that is used to predict pile capacity in the field during pile installation. The original Gates formula tends to over-predict pile capacity for low driving resistances and under-predict pile capacity for high driving resistances (Hannigan et al., 1998). Thus, the Federal Highway Administration (FHWA) proposed a modified version of the Gates formula that addressed this limitation. The FHWA–modified Gates equation is:"

Jan 1, 2017

By Michael J. Marasa

"Geotechnical engineering and construction primarily relies on the subsurface characteristics of the particular site; however, obtaining both accurate and precise information on those features is challenging due to the numerous factors involved in testing procedures used to analyze varying site geology. This includes a detailed and thorough geotechnical investigation to understand the site conditions, allowing the implementation of the most practical and economical solution.This paper presents a case history of the installation of wick drains and construction of aggregate piers on the site of a large facility to be constructed in Memphis, Tennessee. Throughout intensive subsurface investigations, highly variable soils were encountered, requiring settlement control and increased bearing capacity. This paper will discuss the design and installation of the systems constructed, and procedures and execution of the work to ensure design specifications were achieved.BackgroundA 1.4 million square foot expansion directly adjacent to an existing 1.1 million square foot distribution facility in Memphis, Tennessee was planned to serve as a centralized facility for increased production. The first phase of construction included an 858,000 square foot warehouse and parking lot for approximately 400 trucks to the north of the existing structure. The anticipated column load for the warehouse was 125 kips; slab design bearing pressures ranged from 200 to 500 pounds per square foot (psf) and elevations ranged from EL. 264 to 282. Parking lot elevations ranged from EL. 264 to 290, requiring a design life of 10 years with an estimated 100 in- and out-bound trucks daily and maximum weight of 80 kips per truck. The second phase of construction took place east of the existing structure, and included a 794,000 square foot multi-level warehouse, a 100,000 square foot office, and additional employee parking. The anticipated column load for the second warehouse was 225 kips and slab design bearing pressures ranged from 200 to 500 psf. Elevations ranged from EL. 267 to 282. Anticipated column loads from the office were 25 125 kips, with slab design bearing pressures ranging from 100 to 200 psf. Due to the varying elevations within each planned footprint, up to 18 feet of new fill was required to match the existing structure’s finished floor elevation (FFE) at EL. 282."

Jan 1, 2017

By Athul Prabhakaran, Ramin Motamed, Ahmed Elgamal, Milad Jahed Orang, Reza Boushehri

Documented case histories from past earthquakes have exhibited the devastating effects of the liquefaction phenomenon on the performance of buildings that are often presented in the form of excessive settlement of shallow foundations. Example earthquakes include the 1964 Niigata earthquake in Japan, and more recently the 2010-2011 Canterbury Earthquake Sequence in New Zealand, and the 2011 Tohoku earthquake in Japan. All of the listed events comprised several examples of severe liquefaction-related damage to the buildings founded on shallow foundations. Although the liquefaction-induced building settlements have been experimentally studied extensively since 1964 using shake table tests and dynamic centrifuge experiments, studies focusing on cost-effective mitigation strategies are still limited. In this study, the performance of helical piles as a cost-effective countermeasure to minimize the damaging effects of liquefaction-induced ground settlements on buildings founded on shallow foundations is studied. Two large-scale shake table experiments were conducted at the University of California, San Diego (UCSD) to investigate the effectiveness of helical piles in liquefiable grounds. Results from these two experiments highlight a highly improved performance of a shallow foundation supported on helical piles. These largescale shaking table experiments demonstrate the efficiency of using helical piles as a cost-effective countermeasure to reduce the liquefaction-induced building settlement.

By Garland Likins

The Texas Department of Transportation, now considering using Augered Cast-In-Place (ACIP) Piles (also known as Continuous-Flight-Auger or CFA Piles) in their foundations, awarded a research project to Professor Mike O'Neill at the University of Houston (UH) to study the advantages and potential difficulties with ACIP/CFA piles. ACIP/CFA piles were installed on three sites for UH; they had extra instrumentation and additional measurements by UH staff during installation which are beyond the scope of this paper. Independent visual logging of the pile was done by an experienced inspection firm. The main advantages of ACIP/CFA piles are their speed of installation and their economy. Potential savings are substantial. Disadvantages include an unknown structural condition of the shaft. Inspection is critical, but many simultaneous observations make accurate inspection difficult. Because of resulting uncertainty, many engineers have avoided ACIP/CFA piles in the past.

Jan 1, 1998

By Ruth McKeown, Gilson de F. N. Gitirana, Murray Fredlund, HaiHua Lu

The current design standards for the use of anchors in slopes is based on two-dimensional (2D) limit equilibrium analyses. Anchors are considered as discrete loads and the 2D anchor, factored based on the spacing distance, corresponds to extending anchors indefinitely in the third dimension. A three-dimensional (3D) analysis offers a more realistic representation of the problem, including the true discrete nature of the anchor point loads. This paper explores the typical differences between analyzing anchors in 2D and 3D, using four typical conceptual models. Slopes with constant cross sections were shown to be adequately represented by the traditional 2D approach. The maximum difference between 2D and 3D models was 21% and becomes negligible for lower anchor spacing values, as expected. A slope with an external load was analyzed to evaluate critical slip surfaces with lower aspect ratios. Slip surfaces with lower aspect ratios presented higher edge effects that contributed to the stability of the slope. The results indicate that optimum design requires the 3D evaluation of field conditions inducing low aspect ratios, such as concave and convex surfaces, weak layers, and external loads. INTRODUCTION Slopes may be stabilized using a variety of solutions, including anchors. When performing an analysis, geotechnical engineers often follow the traditional two-dimensional (2D), Limit Equilibrium Method (LEM). It is important to understand the consequences and limitations of the assumptions on which the 2D LEM is based. There are numerous studies on anchors that show the importance of considering the actual three-dimensional field conditions. Desai et al. (1986) proposed a three-dimensional procedure based on the Finite Element Method and considering elastoplastic behavior and interface elements, to account for stress and displacement distributions, the relative motion between the anchors and the soil mass, and nonlinear soil behavior. Several important stabilization mechanisms were explained. The role of grout injection was evaluated in terms of the produced normal stresses along the anchor-soil bounding surface. The approach was shown to reproduce adequately experimental tests on a sand, proving realistic stress distributions around the anchor. Nonlinear soil behavior influenced to a large extend relative interface motions. Michalowski (1989) applied an upper-bound limit analysis in 3D to slope stability analyses. Anchors were not specifically considered in this study, but the consideration of locally loaded conditions shed light on important modeling aspects. The manner how the slide mechanism becomes three- dimensional as the slope is locally loaded was demonstrated. This emphasizes the fact that anchors should produce field conditions that require 3D analysis approaches.

Jan 1, 2019

By Edwin W. Hickey

This paper briefly discusses the geologic conditions in South Florida relative to the design, construction, and performance of deep foundations. The subsurface conditions in this area are unique in that the rock layers are highly porous and often very soft, and are sandwiched between layers of typically loose, uncemented quartz fine sands. Due to the high porosity of the Miami Limestone, 4-inch diameter rock coring is often required to obtain intact samples, and dewatering of excavations is sometimes difficult or impossible. The sand layers, typically tens of feet thick, are very loose to loose in relative density and have been the cause of unexpected large, deep foundation settlements. The engineering properties of the various geologic formations are discussed, along with typical deep foundation types used in the Miami area prior to and after 1980.

Jan 1, 2003

By Ed Revoort, Robert Schippers

In Rotterdam in the Netherlands the project ‘De Zalmhaven’ is being developed. The project consists of the realization of houses, parking facilities, two residential towers of 70 m and a residential high rise of 215 m. An artist impression for the project is given in figure 1. For the high rise a new development in the use of large diameter, drilled piles with a steel casing has been successfully utilized. In this article the installation method of 65 m long steel drilled piles in two consecutive sections is presented. The settlements for the building (and the influence on its surroundings) have been analyzed in detail using 3D Finite Element calculations, which will also be discussed. Finally there is focus on the results of settlement measurements carried out during construction in relation to the settlement prognosis.

May 1, 2022

By Ignatius P. O. Lam

This paper presents information on design analyses of large diameter piles using conventional p-y curves as recommended by the American Petroleum Institute (API RP2A, 1993). API RP2A adopted the soft clay criterion developed by Matlock (Matlock, 1970) based on 12.75-inch piles. API RP2A also adopted the API sand criteria originally introduced by Reese, Cox, and Koop (Reese et. al., 1974) based on 24-inch piles. Since Matlock and Reese published their original papers, there have been several publications recommending changes to their p-y criteria, especially regarding the need to adjust the Matlock p-y curves for pile diameter effects. The following sections attempt to clarify the issue of diameter effects on p-y curves.

Jan 1, 2013

By Alexander Blatt, Franz-Werner Gerressen

Diaphragm wall technique is usually used to construct structural elements in the ground, commonly used for retention systems, permanent foundation elements or deep groundwater barriers, named Cut-Off-Walls (COW). Recent developments proof, that the technology also satisfies the demands for using the diaphragm wall technique for bulk sampling purposes. Such kind of new ideas required the adaption of equipment and tools for a depth capability never reached before by a trench cutter in any commercial application worldwide. Compared to the development of increasing depths, especially inner-city applications with limited space, demand a minimization of equipment to accommodate such projects. The paper will focus on the developments and solutions generated to fulfill these requirements and will give an outlook to future developments. Further it describes finalized reference projects and will give a general outlook on future trends and developments. The Paper/The Presentation explains as well the installation process in general.

May 1, 2022

By Alain Pecker

The choice of a design concept for a bridge foundation is guided by various factors; several of these factors are indeed of technical origin, like the environmental conditions in a broad sense, but others non technical factors may also have a profound impact on the final design concept. The foundations solutions adopted for the Rion Antirion bridge are described and an attempt is made to pinpoint the major factors that have guided the final choices. The Rion Antirion bridge is exemplar in that respect: the foundation concept combines the simplicity of capacity design, the conceptual facility of construction and enhances the foundation safety. The design of these foundations was a very challenging task which required full cooperation and close interaction with all the parties involved: concessionaire, contractor, designers and design checker.

Jan 1, 2013