Search Documents

By Navid Bahrani

Overview ? Case history of footwall slab failure ? Procedure used to build a finite element model ?? Pre- and post- mining topography ?? Slab geometry ?? Excavation stages ?? Input parameters ? Finite element modelling results ?? Unloading-induced displacements (magnitudes & directions) ?? Calibration of overall model using measured prism displacements ?? Shear stresses and displacements along the base of slab ?? Factors of safety at different stages ?? Effectiveness of rock bolts ?? Staged or unstaged model? ? Conclusion

May 1, 2008

By F. Boudreault, C. Hendricks, M. Scobie

Drilling accuracy represents an important quality control factor in minimizing dilution. Apart from geology, the factors governing drilling accuracy are largely within the control of the mine. Setup location and alignment, as well as actual drilling accuracy, can all be monitored toward their improved control. Trajectory deviation during drilling, although usually beyond the control of even the most experienced and conscientious driller, can be accounted for (if not full controlled) by down-hole surveying of blastholes prior to explosives loading. This paper reviews the available instrumentation for improved drill setup and recent field experience with several commercial systems designed for monitoring borehole deviation. It reports on a recent survey of 50 Canadian mines which use blasthole stoping and addresses the reasons for the apparent lack of interest in instrumentation: i.e. does this reflect a lack of awareness of the technology, perceived inadequacies in its performance or a predominant reliance on productivity (drilling and mucking) as a measure of operational efficiency? The survey findings supported the latter viewpoint and showed that very few Canadian mines operate drilling incentive programs that are related to drilling accuracy.

Jan 1, 1994

By P. L. Claessens, S. Belisle, C. Bowen

"Use of zinc shot feed is a well-established procedure among North American electro-galvanizers. This form of zinc is easy to handle and relatively inexpensive when compared with zinc oxide. This paper reports results on the kinetics of zinc shot dissolution in traditional pure zinc solutions and in electrolytes used for the plating of nickel/zinc alloys. Despite the cementation of minor amounts of nickel in the latter solution, acceptable dissolution rates of the zinc shot can be achieved through proper adjustment of the solution velocity. Under these conditions, the nickel shell produced by cementation is continuously abraded, exposing the underlying zinc.IntroductionThe use of insoluble, noble metal-containing anodes rather than soluble zinc anodes for the operation of high current density electro-galvanizing lines has gained almost universal acceptance. Two major reasons for this trend are:• improved control of the process by virtue of constant inter-electrode distance; and• increased productivity because the operation of the lines does not require the relatively frequent interruptions for replacement of consumed anodes .The results of the principal anode and cathode reactions are, respectively, depletion of the zinc content of the electrolyte and the increase on its acidity;"

Jan 1, 1991

By D. Larouche, M. Mardan

Hot tearing is a complex defect in aluminium castings which is produced during solidification when a certain amount of liquid phase remains and weakens tensile resistance of the alloy. In direct chill casting of aluminium alloys, hot tears initiate at the surface of sheet ingots just after the primary cooling zone, where the microstructure is particularly vulnerable. In order to study the hot tearing susceptibility of these alloys, and the effect of grain refiners on their thermo-mechanical behavior , tensile tests were carried out in the semi-solid state ( ~95% solid) and at low strain rates using an apparatus called DCSS, for Direct Chill Surface Simulator. This apparatus, originally developed at Alcan Arvida R&D Centre (ARDC), is an instrumented rig test reproducing the conditions prevailing during the primary cooling stage of the DC casting process. The mechanical behavior of solidifying shells and the hot tear formation under applied tensile loads were measured and the occurrence of hot tearing was observed. Temperature in different locations of the casting, applied load and surface strain were monitored during the tensile tests conducted on aluminum alloys AA5182, AA6111 and AA3104. The microstructure of the tested samples was examined using the optical microscope to evaluate their columnar or equiaxed aspect and their effect on the mechanical response of the alloy. A special emphasis has been given to the evaluation of fractions solid existing in the castings at the start of the tensile tests, taking into account the local temperature, thermal gradient and cooling rates experienced. It was found that excessive grain refiner additions decreased the strength of solidifying shells because of the increased level of porosity induced by easier nucleation of new phases (gas included). It was also observed that cooling rates increased with the level of grain refiner, a phenomenon that was associated to the higher number of contact points obtained with small equiaxed grains. Finally, the concept of a stress based criterion for hot tearing was reinforced by the strengths obtained on not grain refined AA5182 and AA6111 showing similar fraction solid near the surface, but significantly different grain sizes.

Jan 1, 2006

By Robert A. Gault, T. Scott Ercit, Mehmet F. Taner

"Abstract -Vanadium mineralization occurs in oxide-rich horizons within the layered gabbro zones of the upper parts of the Bell River Complex, Matagami, Québec and the Lac Doré Complex, Chibougamau, Québec. The vanadium-rich horizons are well defined on the ground and in aeromagnetic surveys by their high magnetic susceptibility; consequently, magnetic susceptibility can be an indicator of vanadium mineralization. The main oxide minerals are ilmenite and titanian magnetite, containing 20% to 70% of volume and the ratio of titanian magnetite to ilmenite is relatively constant, ranging from about 1:1 to 2:1. Their sizes are less than 5 µm to greater than 1 mm to 2 mm, occurring as coarse- to medium-grained subhedral crystals intergrown with cumulate silicate minerals (plagioclase, pyroxene, etc.). Electron microprobe analyses indicate that the ilmenite grains are mineralogically and compositionally homogeneous and have low V contents (average 0.18% equivalent V2O5). In contrast, the titanian magnetite grains are inhomogeneous, consisting of trellisworks of ilmenite lamellae in Ti-poor, V-rich magnetite [less than 2 wt% TiO2, and 1.41% equiv. V2O5 (1.16% V2O3) for 20 analyses]. Thus, the magnetite is the principal ore mineral of vanadium; it hosts vanadium in the form of V3+, not V5+, as is commonly and erroneously reported. We have also devised a flowchart for the beneficiation of vanadium-titanium ores. Sommaire - La minéralisation de vanadium se trouve dans des horizons riches en minéraux oxydés de la partie supérieure des zones de gabbros lités des Complexes de la Rivière Bell, Matagami, Québec et du Lac Doré, Chibougamau, Québec. Des horizons riches en vanadium ont été bien définis sur le terrain et dans les levés aéromagnétiques par leur susceptibilité magnétique élevée; conséquemment, la susceptibilité magnétique est l’indicateur directe du contenu en vanadium. Les principaux minéraux oxydés sont l’ilménite et la magnétite titanifère, contenant 20% à 70% du volume et le rapport de magnétite titanifère à ilménite est relativement constant, allant d’environ 1:1 à 2:1. Leur dimension varie de 5 µm à plus grande que 1 mm à 2 mm, apparaissant sous forme de cristaux subidiomorphes, de grains grossiers à médiums, intercroissant avec la gangue silicatée (plagioclase, pyroxène, etc.) de la texture de cumulat. Les analyses à la microsonde électronique montrent que les grains d’ilménite sont minéralogiquement et chimiquement homogènes avec un faible contenu en V (moyenne 0.18% équiv. V2O5 ). Contrairement, les grains de magnétite titanifère sont hétérogènes, contenant des lamelles d’ilménite en "trellisworks"; ces grains sont pauvres en Ti et riches en V pour la portion magnétite de la magnétite titanifère [surtout contenant moins de 2 wt. % TiO2, et en moyenne 1.41% équiv. (1.16% V2O3) pour 20 analyses]. Ainsi, la magnétite est le principal minerai de vanadium; elle renferme du vanadium sous forme de V3+ et non de V5+, tel qu’il a été communément et à tort rapporté. Nous avons aussi défini un "flowchart" pour la bénéficiation des minerais de vanadium-titanium."

Jan 1, 1998

By Michael L. Free, Shukla. Abhijeet

The short-circuiting tendency of a copper electrowinning cell (EW) based on the roughness of cathode deposits was investigated with varying parameters such as Cu concentration, guar concentration, current density, and temperature. A bench scale EW cell was set up to produce copper under conditions similar to industrial Cu EW. In addition, a statistical analysis and finite element analysis were performed to analyze the deposited thickness, surface roughness and maximum feature height. Interaction data for the cathode deposits suggest that current density and Cu concentration together affect the roughness of deposit more than the combined effect of guar and temperature. Model predictions of roughness were similar to experimental values. The predicted time to short-circuiting was similar to the measured time. This study provides an industrial relevant baseline against which new operating parameters can be compared.

Jan 1, 2014

By Jeff Smith

Agenda About NORTHPARKES The NEED The INITIATIVE The SEARCH The PRODUCTS The SOLUTION The RESULTS The Northparkes copper-gold mine in Central Western NSW commenced operations in 1994. Copper concentrate is produced and shipped to smelters in Japan, China & India under long term contracts with spot sales to other Asian countries.

May 1, 2006

By T. Gerritsen, T. Plikas, K. Ochoa, M. Loveless, R. MacRosty, J. Reichart, R. Pula

Sidewall accretion in a smelting furnace plays an important role in furnace integrity as it provides protection to the sidewall cooling elements and thereby extends the furnace campaign life. The extreme thermal and mechanical stresses in the furnace and changes in the slag chemistry can cause the sidewall accretion to melt or break away decreasing the lining protecting the cooling elements. Thin accretion is highly undesirable as it increases the risk of exposing the cooling elements to the molten bath and in the worst case may lead to a failure. Therefore, monitoring the sidewall accretion on an operating furnace is extremely important to manage furnace integrity and to support safe furnace operation. Operators often generate estimates for sidewall accretion and refractory thickness using either copper cooler temperatures or heat load into the cooling water circuits. Multivariate statistical models, on the other hand, have the capability to consider all the process measurements simultaneously to provide a more reliable estimate. This paper describes the application of multivariate statistical models for sidewall integrity monitoring on a Flash Converting Furnace (FCF) and also discusses the online implementation of these models as the Sidewall Accretion Monitoring System. INTRODUCTION Rio Tinto’s Kennecott Utah Copper (KUC) smelter located near Salt Lake city, Utah operates a Flash Smelting Furnace (FSF) and a Flash Converting Furnace (FCF) to produce high-grade matte and blister copper respectively. Since the commissioning of smelter in 1995, several improvements were made to these furnaces to increase their efficiency and operational safety. At present, Kennecott smelter is known to be among the lowest-emission and highest energy recovery copper smelters in the world. Since the smelter start-up, Kennecott has invested in several advanced furnace monitoring practices to evaluate the integrity of the furnaces and improve their campaign life. An example is their temperature monitoring system installed for the smelting and converting furnaces, which continuously monitors the furnace sidewall temperatures and notifies the operators during temperature excursions. During an investigation on the converting furnace, it was revealed that there were frequent temperature excursions in the settler sidewall area towards the reaction shaft end of the furnace that caused significant furnace downtime. The reason for the sidewall temperature excursions was not clearly known.

Jan 1, 2019

By Tom Shumka

Introduction ?This technique detects 100% of all gear tooth surface indications, providing comprehensive data, and has the ability to size indications accurately. ?The remarkable advantages of ECA technology, is improved inspection capabilities and significant time-savings. ?The advantage of using EMCD is its ability to size indications accurately. ?This technique does not require the gear teeth to be wiped down by hand after cleaning as in MT, LT or UT inspections. (Figure 1) ?This technique will inspect one gear tooth in 30 seconds. ?All of the data can be archived for future comparisons in an electronic report. Methodology ?This technique utilizes Eddy Current Array (ECA) as the principle inspection technique. ?What has been added are specialty scanner probes with multiple coils, a multiplexer and a software package. ?With 2 and 3D dimensional isometric displays, the defect can be seen electronically as it is on the gear tooth surface, thus, reducing the reliance on human interpretation.

May 1, 2011

By M. Pötsch, A. Kluckner, P. Söllner, W. Schubert

"The in situ block size is a key parameter in the geomechanical characterization of rock masses. It describes the fracturing of the rock mass and thus is a measure for the degradation of the rock mass strength. Several classification systems use the in situ block size. For instance, the Geological Strength Index (GSI) requires the “blockiness” and joint surface condition factor as key input parameters. The “blockiness” has recently been related to the in situ block volume (Cai et al., 2004). Due to the limited information about the internals of a rock mass, it is not possible to determine the in situ block size directly. Currently, the in situ block size is determined by calculations using oversimplified models, vague estimations or, due to the lack of relevant information, it is neglected. As remote measurement systems have become available for rock mass characterization, a more comprehensive record of discontinuities can take place. Measurements can be performed on exposed rock outcrops and in particular on tunnel faces and walls, delivering the location, orientation, spacing and persistence of discontinuities at an arbitrary number and locations. An estimation of the in situ block size at the same level of sophistication is still not available. This paper aims at examining the relationship between visible and measureable information at the rock surface, and the in situ block size. Three-dimensional block model simulations were performed using the block model engine of the distinct element code 3DEC. Initial investigations focussed on the minimally required observation area in order to obtain reliable block size distributions. Based on a representative volume element, a reference distribution of the block area at the observation area for a specific discontinuity system was determined. Subsequently, the size of the observation area was decreased stepwise and each new distribution was compared to the reference distribution. For all analyzed systems, it turned out that the mean block area must be smaller than 1% of the observation area to achieve a reliable block size distribution. Further simulations focussed on discontinuity systems with three non-persistent sets. The results were compared to the formula proposed by Cai et al. (2004). A transformation factor T was introduced which replaces the persistence terms in Cai et al.’s proposed formula. The factor describes the correlation between block volumes generated by persistent and corresponding non-persistent discontinuity sets. The simulations included the variation of the discontinuity set spacing, persistence, and orientation. The mean and additionally the 25%-, 50%- and 75%-quantiles of the block size distribution were analyzed. Examining all values for the transformation factor the distribution can be described by a power function with a negative exponent. The function depends on the persistence only. Finally, the results of random simulations were compared to the analytical formula using the transformation factor. The predicted mean and selected quantiles show a good agreement with the simulation results. It gives a comprehensive picture about the block size distribution in discontinuity systems with three non-persistent sets."

Jan 1, 2015

By Lloyd H. Yeomans

"This paper will cover recent developments in conveyor applications with specific reference to capacities, bell speeds and distances. It will also discuss certain unique arrangements of horizontal, curved and loop belt systems. In addition, the recent changes in safety factors resulting from new conveyor construction methods will be reviewed.IntroductionConveyor belt systems are currently undergoing dramatic changes. Their use is being extended to providing a viable means for the transportation of bulk material over longer and longer distances.In this paper, a brief account of the historical development' of the belt is outlined, demonstrating how conveyor technology has adapted to changing market demands.Today, energy and environmental requirements are providing what may even be greater challenges. The ability of the belt conveyor to transport material and meet those requirements, places it in the position of replacing many conventional means of bulk material transportation.The paper also outlines some of the progress which has been recently made in this regard and includes a broad approach to the subject of belt design and application.Recent design developments have greatly extended the potential of conveyor belt systems to include applications thought impossible just a few years ago.Graphically illustrating the potential of this new technology IS a belting system currently operating in New Caledonia. Built in 1970, the system has an incredible centre distance of 43,000 ft, or about eight miles.Not to be outdone, the British Coal Board is currently constructing a belt system with a centre distance of 49,000 ft and a speed of 1,650 feet-per-minute. This system is expected to be completed in 1986.These innovative advances contrast dramatically to the conveyor belt's beginnings in the early industrial revolution. Oliver Evans, writing in the 1795 edition of 'Miller's Guide' defined the conveyor belt as a ""broad endless strap of thin pliant leather or canvas, revolving on two pulleys in a case or trough.""Obviously, the conveyor belt has come a long way since those early days."

Jan 1, 1983

From 1999 to 2008 rock related accidents accounted for 75 fatalities, nearly 6,000 injuries and almost 14,000 incidents (Pappas and Mark, 2011). Clearly this shows that rock related safety on coal mines remains a serious issue and more effort is needed to address this hazard. This paper reviews support design considerations and monitoring needed to improve rock related safety in room and pillar coal mines in the USA. From the present study design considerations continue to evolve and improvements in technology and a better understanding of failure mechanisms and methods to prevent these failures from occurring are in place. At first glance, the design of safe and efficient underground openings appears simple until the designer begins to realize the complexities and variability of geometries, geology, loading and stress influences, support designs and other factors such as corrosion and economics. Ultimately the goal of all designs is to ensure that it can be completed safely, last for the duration of the design life and it is economically feasible.

Aug 1, 2013

By Andrew Bamber

The mining and beneficiation of minerals is the second largest end-use of electrical power on the planet, and comminution is by far the largest single contributor to this. Several jurisdictions, including British Columbia, have, in response to concerns about greenhouse gas emissions and climate change, adopted energy conservation legislation, including carbon taxes, carbon trading and conservation incentive schemes. Key to achieving conservation objectives is firstly an understanding of usage metrics across the various unit operations in the sector, and secondly an understanding of the conservation potential represented by available technologies and approaches in reducing end-use. This paper presents the results of a recent utility-funded study on energy use metrics and conservation potential at large open pit mines which are typical of the sector in BC.

Aug 1, 2013

By V. S. Gischig, G. Preisig

Hydraulic stimulation of deep reservoirs is an essential procedure for developing engineered/enhanced geothermal systems (EGS), but also in other Geo-energy contexts. The goal is enhancing permeability to such a degree that fluid flow rates within the reservoir are sufficiently high for an economically productive reservoir. Two fracture stimulation mechanisms are distinguished that may occur concurrently during the hydraulic treatment: 1) During hydro-fracturing (HF) new tensile fractures are propagated from the borehole by means of a fluid pressure overcoming the minimal principle stress d3 plus the tensile strength T0 of intact rock. In case of a pre-existing fracture oriented normal to d 3 , the fracture can be opened by exceeding d 3 only. Fluid injection is performed via small packed intervals for creating a stack of hydraulic fractures. 2) During hydro-shearing (HS), over-pressure induces slip along pre-existing fractures that are favourably oriented in the stress field for reactivation in shear. Such stimulation is usually performed in a large packed interval or in an open borehole. Which mechanism occurs predominantly during stimulation depends on the rock mass structure and in-situ stress field, but also on the orientation of discontinuities intersecting the open-hole section and thus being pressurized. Both mechanisms also differ in how they affect fracture permeability. While permeability gained by HS is mostly irreversible due to rearrangement of asperity contacts accompanied with shear dilation, permeability enhanced during HF reduces nearly reversible after pressurization unless proppant is used to ensure permanent apertures. In this contribution, we critically discuss the pros and cons of both mechanisms regarding efficiency of enhancing permeability and the associated hazard of induced earthquakes based on literature review and numerical modelling. We review literature that reports on how much permeability required for productive EGS reservoirs and how much permanent permeability can be gained by stimulation. We also compile information regarding the degree of seismicity induced during HFor HS-dominated stimulation procedures, together with conceptual studies that reveal characteristics of seismicity associated with the two mechanisms. Many observations and models indicate that HF may have a higher tendency of being aseismic, while felt seismic events are usually associated with HS. Further, we present a hydro-mechanically coupled fracture flow model that investigates, if and to what degree the stimulation strategy can be designed such that one of the two mechanisms is evoked and dominates over the other. It shows that HS may dominate in presence of larger persistent fractures nearly optimallyoriented in the stress field, even if HF is attempted in short packed intervals. The model further demonstrates that stress transfer during HS promotes the development of permeability across an anisotropic layer of the stimulated rock instead of a large volume. Hence, the study sheds light onto the feasibility of creating productive EGS reservoirs in crystalline rock at several kilometres depths.

Jan 1, 2015

By J. S. Scott

"The Quemont property comprises 640 acres lying directly north of and adjoining the Noranda (Horne) mine. During 1926 to 1928, United Verde Extension Mining Corporation sank a shaft 235 feet and did 3,000 feet of development work on the 215-foot level. Between 1929 and 1930, Quemonr Mining Corporation deepened the shaft to 926 feet, and did further lateral work and drilling on the 500- and 900-foot levels. This work was confined to an area close to the south boundary and met with little encouragement.Following a period of idleness a magnetic survey was made in the winter of 1944, followed in the summer of the same year by some 6,000 feet of drilling. The first successful hole was drilled in February, 1945, from the ice of Osisko lake.To the time of writing, 131,000 feet of drilling, surface and underground,have indicated a large tonnage of gold-silver-copper-zinc ore, and although some knowledge of the geology and structure is emerging, it is too early to draw definite conclusions. The following brief description deals only with those structural features that are reasonably well indicated."

Jan 1, 1954

By Boyd Davis, Vladimiros Papangelakis, Douglass Duffy, Michael Carlos

"The processing of lateritic saprolite in hyper-concentrated magnesium chloride brines offers several potential advantages for the hydrometallurgical production of nickel. An aggressive HCl-MgCl2 leach at atmospheric pressure can significantly reduce magnesium dissolution, and offers the ability to recover HCl and MgO by a less energy intensive process than conventional techniques via the formation of magnesium hydroxychlorides. Inevitably, the high chloride concentration renders iron fully soluble during leaching and thus requires subsequent iron control and disposal steps. Experimental measurements coupled with OLITM modeling were conducted to investigate the behaviour of iron in concentrated magnesium chloride brines, in terms of chemistry (nature of iron species) and solubility limits. The solubility of ferric chloride in magnesium chloride solutions of concentrations and temperatures relevant to this process was controlled by a previously unreported solid phase: 2.5FeCl3·MgCl2·7.5H2O. Iron precipitation tests on synthetic leach solutions without seeding indicate a metastable akaganeite precipitate which transitions to hematite upon equilibration. Magnesium chloride solubility in ferric chloride solutions was also investigated to allow the simulation of a ternary phase diagram for the MgCl2-FeCl3-H2O system, in order to determine process conditions that avoid unwanted chloride precipitation.INTRODUCTION In the search for more economical processes to treat lateritic saprolite for nickel production, chloride hydrometallurgy has been increasingly investigated. While High Pressure Acid Leaching (HPAL) can frequently economically treat lateritic limonite, the presence of saprolite negatively affects process economics. The higher magnesium content of saprolite increases acid consumption, because magnesium sulphate, unlike iron and aluminum sulphates, does not hydrolyze in HPAL. This soluble magnesium decreases the sulphuric acid strength by an amount greater than the amount of acid stoichiometrically required to leach magnesium, which must also be disposed of or recovered (Jankovic, Papangelakis, & Lvov, 2009). Due to these issues, pyrometallurgy is most commonly employed to treat lateritic saprolite, via the Rotary Kiln-Electric Furnace (RKEF) process; this process uses a rotary kiln to dry and partially reduce nickel and iron oxides before sending the calcine to an electric furnace for smelting to produce a ferronickel product for the stainless steel market. Although the problems encountered during hydrometallurgical processing are avoided and nickel recoveries are high, high capital and energy costs prevent the application of this process to lower grade lateritic saprolite deposits (De Bakker, 2011)."

Jan 1, 2016

By J. E. Nesset, E. R. Bobicki, K. L. Bilaniuk

The introduction of froth flotation technology in Canada, and in particular, in British Columbia, began not long after it was successfully applied in the Broken Hill mining area of Australia which began around 1905. It proved to be a revolutionary and transformative technology that resulted in marginal operations in copper, lead and zinc becoming profitable in spectacular fashion. The paper presents the technology of both oil flotation and froth flotation in the context of the challenges of the time and its early application in British Columbia at the Le Roi No.2 mine (1903), the Britannia Copper mine (1912), and at the Allenby concentrator of the Copper Mountain mine (1918-19). New-found archival documents indicate the Britannia application to be the first production application of froth flotation for copper ore outside Australia, a claim that is currently made by the Braden mine (now El Teniente) in Chile. Flotation was initially an add-on process following gravity methods but was rapidly shown to be far superior method for the bulk and selective recovery of metal sulphides. Flotation proved particularly successful for the recovery of zinc sulphide (the so-called ‘zinc problem’) which was considered a contaminant at the time. The ‘copper problem’ related to the poor recovery of fine copper sulphide particles that were not amenable to gravity methods. The success of flotation led to changes in both the scale and methods of mining, concentration and smelting in a manner that allowed integrated mining companies to flourish. Many are still with us today. INTRODUCTION The advent of froth flotation in the early 20th century was truly a revolutionary technological development, not only for the mining and metallurgical industries, but arguably more so for business and society overall. The Canadian technology historian Jeremy Mouat stated (1996) “The development of flotation was the greatest single metallurgical improvement of the modern era...it is not overstating the case to claim that flotation was of central importance to the smooth functioning of the global economy”. It should, therefore, be a story of interest to us all. The aim of this paper is not to retell the full story, that has been well covered by others (Hoover, 1912; Rickard, 1916a; Hines & Vincent, 1961; Lynch et al., 2010) but rather to add some Canadian perspective and the key role played by companies and individuals in those early days, focusing on events in British Columbia’s copper industry. EARLY DEVELOPMENTS During the later half of the 19th century, a number of flotation-related patents were issued. These include the 1860 patent (Britain) granted to William Haynes for a process to separate sulphides from ground ore by mixing it with oil (1-10% wt) followed by a separation process in a water-filled vessel; the 1877 patent granted to Georg and Adolph Bessel (Germany) for a process involving the mixing of oil and graphite ore followed by boiling in water to produce a high grade graphite froth (>90% carbon); and the 1885 patent granted to Rebecca ‘Carrie’ Everson for the separation of sulphides by mixing sulphide ore with small quantities of oil, and adding water followed by sulphuric acid. These processes are more properly referred to as bulk oil flotation due to the relatively large quantity of hydrocarbon used.

Jan 1, 2019

By P. K. Kaiser, D. D. Tannant

"A support system for large ground convergence conditions or burst-prone ground must contain holding elements (rockbolts, cable bolts, etc.) that are strong yet capable of sustaining large deformations, i.e., they must absorb as much energy as possible. Steel wire rope anchored in a borehole by a friction bolt provides these desired yield characteristics if the frictional anchorage is placed deep enough into the rockmass, i.e., in non-yielding rock or beyond the expected depth of rock ejected during a rockburst. Pull-out tests were conducted on wire ropes anchored by inflated Swellex bolts to assess the feasibility of this support concept. The test results demonstrate that a Swellex bolt generates a frictional anchorage that allows the wire rope to slide at high loads and to absorb significantly more energy than either a Swellex bolt alone, or a cement-grouted cable.The rope/friction bolt combination can be engineered to provide the desired energy absorption and allowable deformation by varying the installed lengths of the friction bolt and the rope. For yielding rope support, the contact length between the rope and Swellex bolt must be short enough to ensure that the rope can slip well before its tensile capacity is reached. A safe maximum overlap length is about one metre for the wire rope used in this testing. When used as support in the backs of drifts, a swaged button on the ropes end must be used to ultimately mobilize the full rope capacity thereby protecting against gravity-driven falls of ground."

Jan 1, 1995

By J. Béland

"Three stages, each characterized by a particular sedimentation, magmatism, mineralization and deformation, are recognized in the geological history of Gaspe. The first stage led to the formation of the Taconian orogen, the second to that of the Acadian orogen and the third stage to the accumulation of a post-orogenic cover. The Taconian orogen includes volcanic and detrital rocks of Late Precambrian or Cambrian and Lower to Middle Ordovician ages in which ultrabasic intrusions have been emplaced. Folding is severe. Mineralization is of the Cr-Ni-Cu type, related to the igneous facies.The rocks constituting the Acadian orogen include two distinctive sequences corresponding to two successive sub-stages. The second substage began in Early Devonian time with the first pulses of the Acadian orogeny. The rocks of the first substage grade southward from a nearly platformal sequence to an assemblage implying less stability and spotty volcanism. The second substage was one of synorogenic deposition of elastic rocks, first in a marine environment and later under terrestrial conditions. Granitic intrusions, surrounded by aureoles of skarn and hornfels in which Cu-Pb-Zn mineralization is found, accompanied the Acadian deformation. The second-stage"

Jan 1, 1969

By A. M. Cormie

Introduction The purpose of this paper is to give a brief, general outline of mining practices at Torbrit Silver mine. The geology of the mine is touched on as it is felt that a rough picture of the geology will result in a clearer understanding of the mining methods employed. The main part of the paper deals with mining methods and a section is included on haulage. Development practice is mentioned only briefly. Torbrit Silver Mines, Limited, a subsidiary of Mining Corporation of Canada, is located in the Alice Arm area of northern British Columbia. Access to the mine is by boat to the village of Alice Arm at the head of Alice arm, then truck road, following the course of Kitsault river for 18 miles in a northerly direction to the plant site. The main portal is a further two-thirds of a mile along the course of the river, at approximately the same elevation as the plant, 1,014 feet above sea level. Geology The ore occurs in a massive, irregular-shaped quartz-barite body replacing a folded area in a series of volcanic breccias, tuffs, and flow rocks locally referred to as 'green-stones'. A series of parallel, nearly vertical, fine-grained basic dykes cut across the formation at right angles to the strike of the ore belt over a horizontal distance of 140 feet. The whole of the quartz-barite vein material, which ranges up to several hundred feet wide in places, carries silver values but commercial grade is confined to lenses and shoots where there have been more than usual concentrations of native silver and silver-bearing minerals. The ore-bearing structure plunges at approximately 25 degrees along an axis striking roughly N.65°W.

Jan 1, 1951