Search Documents

By S. Ross, M. Mayhew

"Kirkland Lake Gold introduced battery equipped vehicles (BEVs) at the Macassa Mine in 2011. The fleet of underground BEV haulage trucks and loaders has grown over the years to over 30 units, the world’s largest, currently handling approximately 80% of the daily production tonnage. The inflow and outflow of air occur through a limited number of relatively small openings, which limits the air volume delivered to the underground workings. In addition to improving air quality, the reduced heat load generated by the BEV (when compared to diesel equipment) had a significant positive impact in the workplace. The use of BEV for material handling has enabled increases in production that would not have been possible using diesel equipment.INTRODUCTIONMacassa mine was developed as a track-drift access mine, with the most recent shaft (#3) sunk in 1986. A new mining complex, the South Mine Complex (SMC) was discovered below the 5025 foot elevation south of traditional mining areas, and the majority of mining now occurs in the SMC. The discovery of that zone has led to an internal ramp which is used to access the SMC and haul ore to #3 shaft.The amount of airflow that can be moved through the mine is limited by the existing infrastructure to surface. This amount was recently increased to near its practical maximum from 118 CMS (250 kCFM) to 151 CMS (320 kCFM).Both diesel and electric equipment are used at Macassa. Tethered Load-Haul-Dump Machines (LHDs) have been replaced with Battery Electric LHDs, due to their increased mobility and depth of the mine. Battery trucks continue to replace locomotives to transport both ore and waste to the shaft, as mining has transitioned from tracked levels to trackless level and haulage has transitioned from horizontal levels to an inclined ramp.EQUIPMENT FLEET AT MACASSAMost of the primary material movers utilized at Macassa Mine are battery operated. As the mine goes deeper the battery technology will continue to be critical to the success of the operations. With over 300,000 hours of proven operation success, the battery technology and equipment will continue to be a major part of Macassa’s future."

Jan 1, 2019

By Frank Ebbutt

Introduction The property of the Britannia Mining and Smelting Company, Limited, is situated on the east side of Howe sound, about six miles from its head. It is roughly thirty miles by water from Vancouver, one of the important ports of the Pacific and the industrial and financial centre of British Columbia. Howe sound is navigable for ocean-going vessels and Britannia Beach is a daily port of call for the commodious boats of the Union Steam-ship Company, sailing from Vancouver. Few mines are so ideally situated or have so many or varied natural advantages. Copper was first found on Britannia mountain in 1888, by Forbes, but it was not until 1898 that five claims were staked here by Oliver Furry, a trapper. It is from these claims that the major production during the past thirty years has come. In 1900 the Britannia Copper Syndicate was formed and development of the property was commenced. In 1903 the late Grant B. Schley obtained control, and through his efforts the Britannia Mining and Smelting Company was organized in 1908 as a subsidiary of the Howe Sound Company. Since that time, a persistent and progressive policy has been followed, which has resulted in a prolonged and profitable operation. The country in the immediate vicinity of the mine is marked by strong relief, with mountains rising abruptly from tide-water to elevations of 5,000 feet and more. Two broad transverse valleys deeply dissect the area. These are the valleys of Britannia creek and Furry creek. The region has under-gone prolonged and relatively recent glaciation. Over much of the surface there is deep overburden and dense vegetation. The geology of the mine and vicinity has been described in reports by S. J. Schofield (1), H. T. James (2), J. G. Barry, and others (3). The present writer is in accord with much of this literature on Britannia, but during recent years, extended observations made underground have shown that the 'quartz porphyry', or 'mine porphyry', of several of the earlier writers is not the host rock to the commercial mineralization; and he contends that the mineralization occurs in highly altered phases of a complex series of ruffs, flows, and pyroclastics and their autoclastic metamorphosed products.

Jan 1, 1935

By L. A. Anestiev

A method based on use of calorimetric data for the determination of solidification kinetic parameters is proposed. The method incorporates recent theories of nucleation and growth and allows modeling heat fluxes observed in calorimetric experiment. Statistically optimal estimations of the kinetic parameters, which include the activation's energies of nucleation and growth, are derived from experimental data by means of nonlinear regression analysis. The method is applicable to pure substances and alloys. The evaluation of the kinetic parameters characterizing solidification of pure Al is used for clarifying and exemplifying the method.

Jan 1, 2004

By R. W. McConnell, R. P. Racher

High quality steel production requires extended treatment of the steel in the steel ladle. This has a remarkable impact on the steel ladle refractories, e.g. the need for high performance functional refractories like purging plugs. Operational changes such as increasing tapping temperatures, longer hold times and more aggressive secondary metallurgy are countered by the need for thinner refractory linings and longer refractories life. These combined factors have led to a resurgence in interest in magnesium aluminate spinel raw materials. Magnesium aluminate spinels have been used in steel-making refractories for many years, in a variety of different forms. This paper reviews the production, properties and performance of spinels. Recent developments in the applications of spinels will also be discussed.

Jan 1, 2004

By Stanley Davidson

"The ore deposit mined by Falconbridge Nickel Mines, Limited, is one of the numerous nickel-copper sulphide bodies marginal to the large oystershaped mass of differentiated norite in the Sudbury district, famous as the world's most important nickel producing field. The unique character of the ore deposits of the district has resulted in its intensive geological study over a period of more than 50 years. The results of these studies have given rise to a voluminous geological literature and to a great deal of controversy as to the genesis of the ores. This description of the structural geology at the Falconbridge mine is presented in the hope that it may form a small part of the chain of evidence leading to a reasonably satisfactory explanation of the ore genesis.The mine, named after Falconbridge township in which the deposit occurs, lies along the southeast margin of the norite mass, which, however, is h::re concealed beneath a deep mantle of glacial sands and gravels averaging over 100 feet in thickness. As a consequence, the deposit was not discovered by the early prospectors, and it was not until 1916-17 that E. J. Longyear, of Minneapolis, located the ore by drilling(ll). The discovery was foreshadowed in 1899 by the work of Thomas A. Edison, who found indications of the deposit by what is believed to have been a combination of magnetic and electrical geophysical surveys. He sank a prospect shaft over what has to date proved to be the largest and richest ore section in the mine. A wet quicksand layer at the rock surface proved impenetrable, however, and the 'Edison' shaft never reached bed-rock.The Falconbridge property was acquired by the Lindsley interests in 1928, and ore output, since its inception in 1929, has gradually risen from a modest beginning to the present 2,000 tons and more daily. Total production in this period is 7,500,000 tons of ore averaging 1.72 per cent nickel and 0.89 per cent copper, together with a small but valuable content of precious metals, principally of the platinum group."

Jan 1, 1954

By E. Cauda, K. Phillips

"Diesel particulate matter (DPM) exposures are a serious occupational health hazard in underground mines. While the complex nature of DPM makes direct analysis difficult, its primary component, elemental carbon (EC), can be used as surrogate. The near real-time FLIR Airtec monitor measures EC mass based on laser extinction. It was developed for use in underground metal/non-metal mines, and calibrated to the NIOSH Method 5040. Its effectiveness has not been demonstrated in coal mines, however, where coal-sourced EC could produce analytical interference. To gain preliminary insights regarding the Airtec’s performance in the presence of coal dust, experiments were conducted in a controlled laboratory chamber. The Airtec EC results consistently underestimated Method 5040 EC for both respirable-sized and submicron coal dusts. While underestimation of coal-sourced EC bodes well for limiting coal interference for DPM measurement, one key reason for the observed trend was non-uniform coal particle deposition on the Airtec filter. This may be problematic in coal mines where DPM and coal dust occur together in the instance that DPM deposition is also non-uniform. INTRODUCTION Diesel particulate matter (DPM) is an occupational health hazard, and underground miners have the potential for relatively high exposures due to their work in confined environments with large diesel equipment (NIOSH, 2011). DPM is heterogenous and complex in terms of its chemical composition (Birch & Cary, 1996; Noll et al., 2006), but elemental (EC) and total carbon (TC) are often used as analytical surrogates (Birch & Noll, 2004; Noll et al, 2015). EC is the solid “soot” component of DPM, whereas TC also includes particulate organic carbon (OC) (Noll et al., 2007). EC and OC can be measured in filter samples using the standard NIOSH Method 5040 (NIOSH, 2003), and summed to obtain TC. In US mines, TC has been adopted as the analytical surrogate for DPM in regulatory activities. In metal/non-metal mines, personal exposures are limited under 30 CFR Part 57. In coal mines, limitations are made on emissions from each piece of equipment (30 CFR Part 72) rather than for personal exposures. This is because coal dust has the potential to interfere with TC measurements in personal samples. In some other countries, and for non-regulatory purposes in the US, EC is also commonly used as a surrogate for DPM in mine monitoring applications [e.g., see AIOSH, 2013). EC generally exhibits a linear correlation with TC (Birch & Cary, 1996; Noll et al., 2006 and 2007) but unlike TC measurements, which are analytically intensive, EC can be determined more simply using a laser absorption/extinction principle on filter samples (Noll et al., 2013)."

Jan 1, 2019

By K. Torigoe, S. Owad, C. Tokoro, Y Tsunazawa

The mechanism of an abrasion process to recover metal values by removing components from printed circuit boards (PCBs) is modeled using a discrete element method (DEM) simulation. To simulate the abrasion process, a model PCB geometry was constructed consisting of bonded particulates. The simulation allowed connections between particles to be broken if the bonding force calculated from DEM exceeded a threshold level. Simulation results were compared with experimental comminution data using an agitation mill with test PCBs on which nine capacitors were surface solder-mounted. Simulation results obtained from the DEM with the anchoring model corresponded to experimental observations.

Jan 1, 2011

By C. Desmeules

"Carbon addition in the oxide pelletizing process is a big concern at the Sidbec-Normines pelletizing plant since 1976.Laboratory pot-grate testing carried out before the initial start-up of the Port-Cartier plant indicated that the nominal pelletizing grate capacity could be increased by fifteen per cent with a suitable carbon addition. Also an improved induration cycle offered the possibility of a significant energy reduction within the process with no adverse effect on pellet quality. A one-month plant scale program duplicated the lab test results and confirmed the anticipated cost saving by using these techniques. Since March 1980, Sidbec-Normines used coke addition as a current operation.This paper reviews briefly earlier laboratory and in-plant test work carried out to investigate the effects of adding carbon materials to the Fire Lake hematite concentrate, and presents operation techniques and plant results of carbon addition in the Port -Cattier pellet plant.IntroductionThe Sidbec-Normines pelletizing plant at Port-Cartier, Quebec, is designed to produce six million ton s per year of oxide pellet s. It is a Dravo-built two-line plant; one line to produce three million s tons per year of blast furnace grade pellets averaging 5.5 per cent silica, and another line of three million ton s to produce direct reduction grade pellets of about 2.0 percent silica.The laboratory pot-grate test program was conducted in 1977 at the British Steel Corporation Research Laboratories in England, with the assistance of J .E. Appleby, consultant to British Steel Corporation (overseas services) Limited.The purpose of that test program was to determine the optimum energy saving cycle and to study the physical and metallurgical effects on blast furnace and direct reduction pellets."

Jan 1, 1983

By M. R. MacIver, M. P. Pawlik

"An image analysis method based on chord length distributions is applied to the batch settling of polyacrylamide flocculated kaolin suspensions. Two features of the interaggregate void space, the void chord length distribution mean and the white-to-black distribution ratio are extracted from an image series obtained over the two hour settling experiments. This approach produces three signal values, from two different probability distributions that can be measured as an indication of underlying sediment bed density and aggregation state. Further work is required on the physical interpretation of the signal, the image acquisition conditions, and the parameter selection methods. It is suggested that this chord length based feature extraction technique may be a useful signal to monitor during batch settling or thickening.INTRODUCTIONFew in situ techniques are available that can be used to directly measure aggregate properties within sediment beds in thickeners or secondary settlers. Typical process variables monitored include rake torque and height, bed level and pressure, feed rate and density, underflow rate and density, settling rate, and overflow turbidity; yet these process variables are only weakly related to process dynamics (Concha et al. 2014). Additional process monitoring signals, based on the direct measurement of aggregate properties could improve solid-liquid separation control and allow the extraction of more detailed information from batch settling experiments.Several optical methods exist for measurement of moving suspensions of aggregated solids in the dilute concentration regime, such as focused beam reflectance measurement (Peng and Williams 1994), and the turbidity fluctuation method (Gregory 1985). In the more concentrated region of a thickener, acoustic backscatter penetration and attenuation measured with an acoustic probe and changes in the underlying solid concentration in the highly concentrated, near-bed region of a thickener as a function of height and time (Hunter et al. 2012). While machine vision for froth monitoring has been thoroughly studied with at least five commercialized technologies (Aldrich et al. 2010), its’ application to the study of thickening has been limited."

Jan 1, 2016

By Wei Ye, Lei Li, Xianjian Guo, Feng He

The purpose of the paper is to study the smelting process of copper concentrate with high Cu/S ratio produced in Africa or other areas around the world and theoretically analyze the influence of slag type on the smelting process. The paper has compared the processes used successfully in smelters, including CAPEX and OPEX and other factors, to provide reference for the industry to select the best process under specific conditions. INTRODUCTION At present, a great amount of copper concentrates with high Cu/S ratio, with chalcocite being the major source of copper, have been produced or are about to be produced in the Copperbelt in Africa and other countries in the world. The copper concentrate is usually high in copper (~30–55wt.%) and low in sulfur (~10–15wt.%). The conventional processes of smelting-converting and roasting-leaching-electro-winning for treating this type of concentrate is high energy and materials consumption such as electric power\fuels\flux et al. The direct-to-blister (one-step) smelting process can be considered favorable due to a reduction in processing steps. Up to now, there are four copper smelters in the world operating with the direct-to-blister smelting process. There certainly are problems in the process such as high copper content in the slag, strict operation requirement of slag cleaning electric furnace, etc. Except technical issues, the impact of factors on economical aspect such as power and material cost needs to be considered comprehensively in process selection. In this paper the technical issues of direct-to-blister smelting process, including slag treatment process, were analyzed and the comparison to the conventional processes and economic analysis of direct- to-blister smelting process to treat high Cu/S ratio concentrate were done.

Jan 1, 2019

By M. Rafati

In this investigation, the effects of T4 and T6 heat treatments of AZ91 magnesium cast alloy have been studied. The effects of different microstructural details such as morphology, size and distribution of precipitates and their influence on fracture mechanisms were investigated by optical and scanning electron microscopy. The mechanical strength of the alloy after T6 treatment was found to increase in comparison to the T4 treatment, due to the formation of discontinuous precipitates in the grain boundaries. Precipitation in this alloy occurs in two ways: continuous precipitation, which nucleates and grows inside the grains, and discontinuous precipitation, which forms at the grain boundaries. During ageing, the length of the continuous precipitates increases, and, hence, interprecipitate distance decreases. The formation of discontinuous precipitates causes initiation and propagation of cracks at and the weakening of the grain boundaries. This is the principal reason for the reduction of the ultimate tensile strength in T6 heat treatment in comparison to the T4 condition.

Jan 1, 2006

By B. Hart, D. J. Miller, J. T. Francis, M. C. Biesinger, Smart. R. St. C.

Diagnosis of the surface chemical factors playing a part in flotation separation of a valuable sulfide phase requires measurement of the hydrophobic and hydrophilic species that are statistically different between the concentrate and tail streams. Time of flight secondary ion mass spectrometry (ToF-SIMS) can be used to identify sufficient particles of a specific mineral phase for reliable statistics determining a mean value for each species with 95% confidence intervals (1). Using the region of interest (ROI) facility in the Tof-SIMS software, a mass spectrum from each particle, at 1-2 monolayer sensitivity, is recorded and stored. This analysis is reported for a chalcopyrite / pyrite / sphalerite mineral mixture conditioned at pH 9 for 20 minutes in order to study transfer of copper from chalcopyrite via solution to the other two mineral surfaces since this mechanism can be responsible for their inadvertent flotation in copper recovery. Analysis from mineral selection based on specific ToF-SIMS signals (eg. Pb, Zn, Cu, Fe, Fe/Cu) indicated no statistical difference in the copper intensities on pyrite and sphalerite after this conditioning. Principal component analysis (PCA) of the ToF-SIMS imaging data identifies combinations of factors strongly correlated (positively or negatively) in images or spectra from mass spectra recorded at each of 256x256 pixels in a selected area of particles. PCA is a better method of selecting minerals due to multi-variable recognition. It has clearly separated a statistical difference in copper intensities between the sphalerite and pyrite phases. The method has been extended to samples from an operating plant again with excellent phase recognition and diagnostic surface chemistry.

Jan 1, 2004

By W. G. McBride

THE present demand for men with engineering training exceeds anything in the history of the profession. Recent estimates indicate that mechanization of war has reached such a stage that at least twelve horsepower is required now for every one horsepower needed to run the machines of the first Great War. The scale of operations exceeds anything in the past, while more territory and people are involved than ever before. Many of our allies have inadequate or no facilities for producing the thousand and one articles absolutely necessary to the conduct of modern warfare. Lack of preparedness has made it necessary to produce at an unparalleled rate to gain parity with the enemy, while our losses have been so heavy that replacement, in itself, presents a task which might well stagger less courageous peoples. This means that not only is there an unprecedented demand for engineers to produce the machines, munitions, and supplies of war, but there is a correspondingly large need for men with engineering skill in the uniformed forces to operate and maintain the vast numbers of ships, 'planes, tanks, trucks, radios, and a myriad of other devices to carry on the varied activities of war. This abnormal demand came upon us after almost ten years of stagnation in the engineering industries. During this time many trained engineers drifted into other callings, while the lack of jobs for graduates caused a falling off in the number of men training for this profession. Consequently, the supply of well trained engineers was below normal when the madman of Germany precipitated us into the present turmoil. Added to all this, we in Canada are still suffering from governmental inefficiency in the utilization of the available supply of engineers. In the armed forces, engineers have been assigned to office and other work where their engineering training is not only wasted but for which men with more suitable training could be found. Mining engineers are debarred from service as aeronautical engineers, and students in mining engineering are denied the bursaries provided for aiding students in engineering. Mining and metallurgical engineers are both barred from the Ordnance department of the army. This arises from a misunderstanding in relation to engineering training. In Canadian engineering schools, all engineers are given a sound training in the branches of human knowledge which are fundamental to engineering: mathematics, physics, and chemistry. The basic difference between the several categories of engineers lies in the fact that training in the application of this fundamental knowledge to the solution of engineering problems is given in different subjects.

Jan 1, 1942

By Yolaine le Beau

Plan de la présentation Le contexte mauritanien La situation de l?environnement en 1999 L?évolution de 1999 à 2010 Bilan La situation de l?environnement en 2011 Le contexte mauritanien Pays du Maghreb couvert à 75% par le désert du Sahara Un des plus pauvres au monde Index de développement humain : 136esur 169 pays en 2010 46,7% de la population ne peut subvenir à ses besoins quotidiens

May 1, 2011

By Terry McNulty

"Previous papers (McNulty 1998 and 2004) have dealt with the causes of successful and less successful achievement of design production rate by new processing plants in the minerals industry. Examination of many case histories has allowed the construction of curves or profiles that represent projects with similar characteristics that equate to differing degrees of care exercised during the project development phase. Simplistically, decreasing care is reflected by increasing risk and a heightened likelihood of poor technical and/or financial performance.This contribution provides an update, including recent case histories, and presents a modified Series 1A curve that includes the best 23 case histories, out of a total of 81 examined, or 28%. This is done to show that some very carefully developed and executed projects can ramp-up quickly and that owners of new projects should avoid being too pessimistic in projecting early cash flow if they are certain that they have done their homework. The role of metallurgical process development in the reduction of project risk is discussed and several financial analyses are presented that express the potential monetary value of a well-designed and professionally executed metallurgical program."

Jan 1, 2014

By I. Govender

Positron-Emission-Particle-Tracking (PEPT) has enabled the non-invasive observation of charge and slurry transport in model mills under operational conditions. We use high quality PEPT data to infer that the charge motion can be effectively described by a non-Newtonian granular fluid. An improved theory for slurry transport, including inertial effects, is presented.

Jan 1, 2012

By Naoki Takada, Dae-Sung Cheon, Minoru Sato, Masaji Kato, Manabu Takahashi, Weiren Lin

"The permeability and specific storage of rocks and sedimentary layers deep underground are critical parameters for issues related to the buried evaluation of natural gas and oil, CO2 aquifer storage, various kind of waste storage and so on.The Shirahama sandstone of the Wakayama prefecture, Kii peninsular in central Japan, consists mainly of quartz grains with no cracks and rock fragments that are aggregations of various kind of minerals. The quartz grains have an average size of about 150 micron. The pre-existing pore sizes were distributed dominantly at approximately 1 micron, and the total porosity was about 13%.During the hydrostatic compression test, we measured permeability of Shirahama sandstone by Transient Pulse test for three mutually perpendicular directions. Permeability of Shirahama sandstone remained fairly constant while increasing the effective confining pressure. Permeability anisotropy was observed slightly in the normal and two parallel directions to the bedding planes.We used micro focus X-ray CT with high resolution of 10 micron to visualize and measure the voids space information in Shirahama sandstone. Three-dimensional data were obtained in the intact and stressed sandstone simultaneously. Pore structures and grain boundaries were clearly distinguished. Pore closure and grain movement were clearly observed with increasing confining pressure. Micro focus X-ray CT is an effective tool to visualize and measure the geometrical information in rocks.Three-dimensional medial axis (3DMA) method was introduced to quantify the flow-relevant geometric properties of the voids structure in Shirahama sandstone using µfocus X-Ray CT data. The number of connecting path between two faces, tortuosity and the shortest path distribution within an arbitrary region of Shirahama sandstone specimen were analyzed. Geometrical information on the number of connecting path shows reasonable correlation between permeability anisotropy and mutually perpendicular directions normal and parallel to bedding planes. In addition, we introduced numerical simulation of fluid flow of pressurized Shirahama sandstone by LBM, to discuss the permeability change caused by pressurization on effective confining pressure. We obtained the detailed distributions of fluid pressure and fluid velocity in relatively narrow voids space more than 10 µm. It was confirmed that pressurization effect on permeability caused by the decrease of the connecting path and the shortest path between arbitrary faces, and then caused a complex condition on fluid pressure and fluid velocity."

Jan 1, 2015

By A. Carbonari

In order to gain competitiveness and compete at a global level, construction companies should improve their efficiency. The problem is even more relevant in the construction field, whose work processes find it hard to evolve towards new automated methods and techniques in the management field. For that reason, this paper suggests how construction companies could apply new technologies to implement automated management of environmental hazards. Based on a survey regarding the environmental risks presently experienced in construction sites, noise and dust were considered two of the main hazards. So in this paper a networked system for real time remote monitoring of the spatial distribution of dust in construction sites was developed. Such a system would relieve builders from the commitment of on-site surveys, allowing for a continuous monitoring of the site conditions and of the real exposure of each worker and pass-by to the pollutants generated by construction works. The main system requirements considered are: easy to deploy, reliable, as accurate as needed to be able to send real-time warnings and store a good estimation of the real exposure to which involved people have been subject to. So far the research produced a prototypical hardware for dust monitoring made up of wireless sensors which can be easily deployed on site. The sensors were calibrated by means of laboratory tests, where their measurements were compared with those collected by means of highly accurate instruments, which were taken as a reference. Thanks to these experiments, calibration curves for the sensors were worked out, showing also the measurement range of the sensors.

Aug 1, 2013

By T. P. Lim, N. K. Davé

"A modified accumulator method was devised to measure surface radon flux from porous media. It consists of a collector hood type of accumulator with a homogenizer pump and a pressure balancer. The latter was used to compensate any pressure changes produced during sample withdrawal and hence eliminate additional radon transport from the media. Errors resulting from radon back diffusion due to decreasing concentration gradient with time across the interface were also eliminated by measuring radon concentrations in the accumulator for two different periods of time and calculating the true radon flux, J(o), from the solution of a time-dependent radon transport equation in the absence of any pressure and temperature gradients.Core samples from the observation site were also withdrawn for laboratory determination of porosity, moisture content, bulk and grain densities, Ra-226 source concentration and the fraction of Rn-222 produced in the void volume. The data were used to calculate the radon diffusion coefficient for the media.Using the present method, the true value of surface radon flux for an abandoned uranium tailings pile was obtained as J(o) = 2020.2 mBq/m2/sec (54.6 pCi/m2/sec) compared to the value J = 1406.0 mBq/m2/sec (38.0 pCi/m2/sec) obtained by the conventional method. The bulk diffusion coefficient of radon for the media was obtained as 1.2 x 10-7 m2/sec.IntroductionRadon-222 (hereafter called radon) released from uranium mill tailings is a continuous source of environment radioactivity in terms of its transport as an airborne gas and its decay products. The particulate daughter products readily attach to aerosols or dust particles and can further be transported by various other environmental pathways. Typical radon release rates from existing tailings piles vary between 740 and 14,800 mBq/m2/sec (20-400 pCilm2/sec), depending on the nature of the tailings material, moisture content, etc. The United States Nuclear Regulatory Commission (NRC) is proposing radon release rates of 74 mBq/m2/sec (2 pCi/m2/sec) above that of background."

Jan 1, 1982

By S. A. R. Keneti

Predicting the geomechanical response of the shale gas material during hydraulic fracturing operation in the field needs better understanding of their geomechanical behaviour under laboratory testing. Anisotropy is considered as a critical factor during investigation and analysis of deviated boreholes, borehole stability, stress-strain and strength behaviour, generation and propagation of fracture and fluid flow. In this study, compressive elastic modulus (Ec) of the Montney shale has been investigated in two perpendicular directions: unconfined compressive strengths test was conducted on the Montney sample to measure its Ec in the vertical direction. This value then was compared to the Ec value in the horizontal plane (i.e. foliation plane) which was previously measured throughout a Brazilian test by Keneti and Wong (2011). From the results, the representative values of Ec in the vertical and in the horizontal directions were found as 25 GPa and 40 GPa, respectively. Computer tomography technique was also employed for the experimental data interpretation.

Jun 1, 2012