Search Documents

By Descarreaux. Jean

"The Abitibi volcanic belt was sampled along a cross section extending from Matagami to a point east of Rouyn. A few samples were also collected in Louvicourt township, Quebec. The major elements were determined for 344 samples, and rock names were defined using normative minerals. The analytical data were studied by means of variation diagrams. The Abitibi volcanic belt is characterized by rocks belonging to both the tholeiitic and calc-alkaline magmatic series, but they show some differences as compared to some typical reference series, particularly those from Japan. Basalt is the predominant rock type and accounts for 44 per cent of the sampled outcrops. The volcanic rocks are relatively poor in K2O and TiO2. Regionally, the volcanogenic copper-zinc mineralization is associated with the calc-alkaline volcanic sequences. Locally, within such sequences, some types of abnormal deviations from the averages are recognized only in association with the copper-zinc mineralization. The anomalies are ascribed to hydrothermal alteration consisting of the introduction of MgO and removal of N a20; enrichment in K20 is also observed where zinc mineralization predominates. Examples of such anomalous zones show that, in places, this alteration phenomenon can be quite extensive. Petrochemical characteristics can be used as geochemical ore guides in exploration programs."

Jan 1, 1973

By H. A. Hamza

An experimental study of the settling characteristics of a washery effluent originating as tailings from a froth flotation circuit was undertaken by using a systematic approach to select the most appropriate flocculant(s) under predetermined conditions. Selection and evaluation procedures which greatly reduce the effort required to select flocculants are described. The results show that, although different flocculants display superiority at different ranges of dosage. Separan MG 700 (Dow) is the most suitable on absolute economic grounds. Flocculant evaluation is based on a Cost Performance Index (CPI) which expresses the cost of flocculant (¢/ton) required to produce a unit settling rate (in./hr). From experiments carried out with a number of flocculant aid and flocculant combinations, it was concluded that the use of flocculant aids can be economically justified only if the settling rates required are higher than those obtainable at the optimum flocculant dosage. Otherwise, the value of the flocculant aid appears to be limited largely to the reduction of supernatant turbidity.

Jan 1, 1979

By Ian McC. Stewart

"Seam gas flow in coal mines takes place through a medium which has both capacity and resistance and can therefore be expressed in terms of the basic diffusion equation, provided that the characteristics of the system can be adequately described. It may be possible to lump the variations from point to point in a seam together as an effective diffusivity. The paper discusses the characteristic flow-time patterns for various types of openings and the particular features of coal and seam which influence the diffusivity.Two field experiments are described in which gas make to a heading and to a borehole were measured in a mine for which considerable data on coal sorption properties were available. Incremental gas flow measured from the borehole experiment predicted the actual flow from the heading measurements remarkably well. The effective permeability adjacent to the face was much higher than expected from the properties of the coal. The incremental flow measurements to a horizontal (in-seam) borehole showed a striking picture of advancing 'relaxation' behind the face which is not discernible by other experimental means."

Jan 1, 1971

By John Stubbs

Sub-Surface Shaft excavation Mine development Headframes Surface Production facilities Product storage and loading Tailings area Infrastructure Discovery Lodge Utilities Operations complex Port Marine loading Rail unloading and storage

May 1, 2013

By T. L. McCall

CHANGES in mining practices have evolved so quietly and unobtrusively that perhaps we scarcely appreciate how truly startling these changes are unless we cast our minds back so as to compare the past with the present. Such retrospection is, indeed, necessary when attempting to forecast the future, for it is only by carefully reviewing the past that we can hope to obtain an indication of what the future may hold in store. In this instance, it is not necessary to delve into the very early history of . coal mining, as our purpose will be served if the last three or four decades are reviewed, a period that is still fresh within the memory of many of us. These earlier days might be termed the selective period of mining, for at that time the coal resources of the world had not been tapped to anything like the extent they are at present and this condition enabled the owners and operators to exercise selective powers and only mine such seams of coal as could be most easily reached an worked at the lowest possible cost and which, at the same time, would suit the requirements of the market. Carrying this thought of selective mining still further, the miner, who was then an artisan skilled in all the branches of his calling, was able to select or discard such parts of the seam he was working that the co al sent out of the mine was acceptable to the consumer with just the barest minimum of preparation. Compare these conditions with the? conditions prevailing today, when coal seams of medium height, good quality, and readily accessible have been largely depleted and the operator has been compelled either to carry on his operations under much greater depths of cover where the coal is more costly to win, or else to work seams of lesser height or of poorer quality.

Jan 1, 1938

By Charles Camsell

At the Annual General Meeting of the Institute in 1924. I endeavoured to present the position held by the mineral industries in the commercial life of this country. The facts and figures were presented at that time in a detached way. Since then, however, I have made some attempt to analyze them in order to determine the causes for that position and to draw some conclusions as to the future of the mining industry. As everyone knows, our trade figures are very often used in political discussion, especially in discussion of tariff policy. It would be entirely out of order for me to say anything touching the tariff issue and I want to have it clearly understood that, in my opinion, the material I am about to present contains not a single statement or conclusion which anyone would be warranted in using as an argument for either a lower or a higher tariff or for tariff changes of any kind. As a starting point, let me re-state, very sketchily, Canada's general situation in external trade. In the last calendar year, 1924, we sold Canadian merchandise of all kinds to other countries to the value of $1,045,000,000 in round figures. Our purchases abroad reached about $893,000,000. Thus our sales exceeded our purchases by roughly $152,000,000. In other words, we had what is known as a 'favourable balance of trade' - one of the biggest favourable balances we have ever had in our history. The proceeds of our sales of Canadian products enabled us to meet the bills for all our purchases of foreign commodities and, in addition, placed a large surplus to our credit with which to offset our interest charges and other obligations abroad.

Jan 1, 1925

By Q. H. Bui

The elastoplastic self-consistent model is one of the effective models to study the initial microstructure effect on the mechanical behavior of bulk materials. However, the use of this micromechanics-based model which takes into account only the Hall-Petch relationship at grain level for predicting the grain sized effects on the strength of the deformed materials is not accurate yet because of the fact that the dislocation density contributes also to the strengthening of this kind of materials. In this study, a modification made to the Hill-Hutchinson elastoplastic self-consistent model was proposed for investigating the microstructure dependence of the mechanical behavior of cold-drawn 6063 aluminium tubes. Because of the novel modification, an estimation procedure with two steps was required to identify the parameters of this micromechanical model. An acceptable agreement between experimental and theoretical stress-strain curves was achieved.

Jan 1, 2011

By Stephen G. Mlot

The evaluation of mineral projects involves the identification, mitigation and management of significant uncertainty. Benchmarking is an essential and effective way of increasing confidence and reducing uncertainty associated with input parameters and assumptions. Comprehensive and detailed benchmarking will ensure ?best practice? technologies, methods and systems have been considered and that the appropriate practices can be identified and incorporated into the project. In conjunction with the involvement of experienced industry practitioners, benchmarking is best employed throughout project evaluation to enable early identification of ?errors?, producing more accurate and predictable outcomes. Considerable time and effort is required to gather data and information, which should be benchmarked by the project evaluation team. There is a history of mining projects underperforming, on production, on costs and on return to the investors. The quality of mine plans and feasibility studies, and the quality of the input data is being questioned in many ways. Benchmarking assists sound project evaluation practices, by providing a database of actual results, to validate project inputs and outcomes, ensuring they are realistic and achievable. Benchmarking also provides unbiased, statistical support as the basis for sound investment decision making and ensures well considered decisions are made resulting in a more efficient study process. The evaluation of the quality of projects which are the subject of transactions also benefits from the use of real data obtained from a benchmarking database. Vendors are quick to highlight the benefits of their projects, and conceal the flaws, inflating the value. Buyers will want to quantify the potential of a project through the due diligence process relying on actual results from benchmarking. For the reasons broadly outlined above, benchmarking should be considered as an essential component of effective Project Evaluation.

Aug 1, 2013

By Tadeusz W. Wlodek

THE known phenomenon that a test-piece of ferro-magnetic steel is magnetic after it has been broken in tension indicates that, while it is being loaded, the steel acquires magnetic properties. In the present investigation of the influence of the stress on the magnetic flux, repeated pulsating stresses of increasing amplitude, varying from zero to the maximum tensile value, i.e., pull-pull loading, were employed. The specimens were prepared from two types of carbon steel and two of alloy steel. The magnitude of the magnetic flux was determined indirectly. The voltage and mode of variation of the electromotive force induced in a coil surrounding the stressed steel specimen were measured as an indication of the varying magnetic flux within the specimen. Curves representing the electromotive force induced by the varying magnetic flux show that as the tensile load increased so also the magnetic flux increased, with a corresponding increase in measured e.m.f. At a certain stress there is a sharp bend in the voltage curve (point Win the diagram, Figure 5); this critical stress corresponds very closely with the yield stress (0.2 per cent permanent strain). Beyond this point, slight increases in the stress produce large increases in the voltage. The wave form of the e.m.f. was registered on an oscillograph. Analysis of the curves so obtained demonstrated the necessity of continuing these experiments, in order to determine the type of induced wave form associated with various types and amplitudes of stresses. In these experiments, the shape of the stress wave was sinusoidal, although the shape of the induced e.m.f. was sinusoidal only up to a certain load and became more and more complex above this load.

Jan 1, 1944

By M. A. Kessick

Current treatment and disposal procedures are compared for clay slimes resulting from the extraction of Alberta oil sands, the extraction of Florida phosphate matrix, the recovery of diamonds from kimberlite deposits in South Africa, the recovery of kaolin from clay deposits in southwest England and the upgrading of bauxite ore. Published research in the area is reviewed, and common trends which are emerging in the disposal of clay slimes are discussed.

Jan 1, 1978

By V. A. Ettel

Current practices in electrolytic winning and refining of copper , nickel and zinc are reviewed from the point of view of their respective energy requirements. The electrical energy requirements of these processes are broken down in to the individual components, which belong to two basic categories: (a) thermodynamic energy requirements (G of the desired reaction) : (b) energy losses (anode and cathode polarizations, ohmic drops in the electrolyte and in the cell hardware, energy losses due to unwanted side reactions and electrical shorts). The individual energy components are separately examined for each electrolytic process and the potential for energy saving in these processes is discussed. It is shown that many potential energy-saving measures are uneconomical at the present time, as they increase over-all operating costs. The discussion is focused on those approaches which hold most promise for the future.

Jan 1, 1977

By R Thomson

The use of uranium metal in non-ferrous metallurgical practice is dis-cussed with reference to its alloying behaviour and chemical activity. It is suggested that the more promising applications are in the treatment of molten metals to combine with impurities. Mines Branch work along these lines is described for copper, zinc, magnesium, aluminum and nickel alloys. It is shown that a cop-per-uranium master alloy (25 per cent U) successfully deoxidizes molten copper without detriment to the electrical or mechanical properties of the product at residual uranium levels of up to 0.8 wt. per cent. Additions of uranium to alpha brass in amounts greater than the lead impurity content were found to remove the deleterious effect of lead on hot-workability. Similar deoxidizing and malleableizing effects were found with uranium additions to nickel. It is thought that uranium forms stable intermetallic compounds with many impurity elements. A significant malleableizing effect can therefore be expected in the presence of other elements besides lead.

Jan 1, 1963

By N. A. White

Whereas the ultimate world supply of energy minerals-defined as fossil fuels and fissile materials - is controlled by geological factors, the actual supply at any particular time is controlled by economic feasibility, technological innovations and /or political decisions. This paper identifies and discusses the principal uncertainties surrounding the international availability of energy minerals from now until the end of the century. A brief comparison is also made between energy and non-energy minerals. Genuine shortage s of energy minerals are now of a very long-term nature, whereas artificial ones may occur at any time and have a serious effect on the world economy due to the dependence of most OECD countries on imports of energy mineral . This paper argues that events over the last decade, such as the demand for a New International Economic Order, the OPEC increase in crude oil prices and the growing international lobby on environmental issues especially relating to nuclear safety - will progressively lead to a major, long-lasting transformation of the energy scene world wide. This transformation will encompass demand, in terms of conservation and efficiency, the supply mix of the various energy minerals , the supply system and the structure of the different energy industries . It is already affecting the role of governments and reaching into the question of national sovereignty both of developed countries, such as the U.K., Norway and Australia, and the developing countries, thereby making energy minerals a key area of international relations.

Jan 1, 1978

By Sean Dessureault

Information technology (IT) initiatives in the past have tended to be sold on their ability to maximize resource output and return on capital by using assets more effectively and efficiently. Many IT projects fail, not delivering return on their investment. This is known in the IT industry as the ?productivity paradox,? where increasing investments in IT do not result in comparable increases in productivity. Experiences and studies of most business sectors reveal that this paradox is rooted in the false assumption that more IT spending automatically results in financial benefit, whereas the true source of benefits is in how effectively IT is used. Most business sectors have accepted that the reengineering of processes is required to gain the full benefits promised of IT. A mining operation has organizational processes similar to most business sectors but unique operational processes. The lessons of changing business practice in more common business processes such as inventory control and customer-supplier relationships can be adequately transposed into a mine. The unique operational processes in mines, in turn require unique redesign efforts. Several enabling information technology opportunities have recently become available, such as more integrated mine production management systems and tactical manger training simulators. This paper reviews the latest IT products and ou lines the processes and kinds of change that will be required in order to benefit from these new investment options.

May 1, 2002

By K. K. Dehn

This study focused on determining the stability of thin shotcrete fill fences at a hard rock mine in northwestern Ontario during increased pour rates of paste backfill. Determination of the stability of the fence is needed for both personnel safety and to avoid failure of a fence. Failure of a fill fence during backfill activities would have severe impacts on production and potential hazards to nearby workers. Approved fill fences at the mine are a slender design of 10.5 centimeters of shotcrete applied to a rebar framework with burlap lined ?bedspring? backing. Approved mine standards dictate that fill rates may not exceed 1.5 meters of paste depth per 10-hour shift when pouring behind a flat fill fence. To decrease the backfill cycle time the study looked at fence stability during increased pour rates of 2.5 meters paste depth poured within a 10-hour shift. An instrumentation design was developed including pressure cells, strain gauges, and tilt-meters that were built into experimental fences to observe the effects of increased pour rates on lateral wall pressures, strain development in the rebar and shotcrete reinforcement, and physical deformation patterns along the face of the fence. The data was analyzed for overall stability.

May 1, 2007

By M. A. Gomez, V. Yahorava, J. A. Strauss

"It is accepted widely that pressure oxidation (POX) is the most appropriate technology for processing of arsenic containing refractory gold ores. However, studies on the stability of various iron-arsenic precipitates formed during POX are limited. Since the behaviour of these phases could have significant practical implications for gold processing plants, it is important to study them in isolation. This paper compares two synthetic precipitates, basic ferric arsenate sulphate (BFAS) and basic ferric sulphate (BFS) in terms of their formation, behaviour during hot curing and cyanidation, as well as their environmental stability. BFS and BFAS were synthesised hydrothermally at 205°C and their mineralogy was confirmed using various techniques. During synthesis, the addition of H3AsO4 into an aqueous Fe2(SO4)3-H2SO4 mixture significantly decreased the iron yield to BFAS in comparison to BFS under equimolar initial iron and acid concentrations. The BFAS dissolution kinetics was slightly faster, as compared to BFS, during subsequent hot curing. Cyanidation test work on the washed synthetic precipitates indicated that the lime consumption of BFAS was three times lower in comparison to BFS, while cyanide consumptions were comparable. Fresh BFS and BFAS precipitates, as well as their cyanidation residues, were found to pass the respective environmental tests in terms of arsenic release.INTRODUCTION Pressure oxidation (POX) is generally viewed as the most appropriate technology for the processing of arsenic-containing refractory gold ores due to the stabilisation of arsenic in the leach residue (Dutrizac & Jambor, 2007; Gomez et al., 2008; Harris, 2003; Collins, Berezowsky, & Weir, 1988). Detailed laboratory studies indicated that several Fe(III)-arsenate type compounds may be formed under typical conditions of autoclave treatment of refractory gold ores (Swash & Monhemius, 1994; Dutrizac & Jambor, 2007; Gomez et al., 2008, 2010; Gomez, Becze, Cutler, & Demopoulos, 2011). The basic ferric arsenate sulphate (BFAS) phase (Gomez et al., 2008), also known as Type II ferric arsenate (Swash & Monhemius, 1994) or Phase 3 (Dutrizac & Jambor, 2007), is one of the most common arsenic-bearing products (Harris, 2003; Dutrizac & Jambor, 2007). BFAS precipitation is viewed as one of the best routes for arsenic stabilisation and performed equally well to scorodite during environmental stability tests (Harris, 2003; Swash & Monhemius, 1994; Dutrizac & Jambor, 2007; Gomez et al., 2008, 2011)."

Jan 1, 2017

By Phil A. Keele

"IntroductionGeneralThe Genesee Coal Mine is a joint venture of Fording Coal Limited and the city of Edmonton. The mine supplies thermal coal to the Genesee Generating Station operated by Edmonton Power and is located approximately 75 km southwest of Edmonton (Fig. I).Under the terms of the joint venture agreement, Fording Coal Limited has designed and developed the Genesee Coal Mine. Fording also operates the mine which has a minimum economic life of thirty-five years. Mine development started in the spring of 1987 with the construction of the dragline erection pad and mine service complex. Major development of mining areas was carried out in 1988 with the construction of haul roads, powerlines, topsoil recovery, etc. Mining officially commenced on December 14,1988.The mine produces 1.6 million tonnes of coal per year and employs 65 people. MiningGround conditions have turned out to be very poor, as expected with the majority of the overburden in the first few years a soft lacustrine clay with minor amounts of fine-grained glacial till. To compound matters, what was expected to be a relatively uniform coal subcrop turned out to be a very irregular erosional contact.The coal mined at Genesee is a sub-bituminous Class B thermal coal with approximately 16070 ash, 21% moisture, 8300 Btu/lb and 0.27% sulphur on an as-mined basis.The primary piece of mining equipment used at the Genesee Coal Mine is a M8200 walking dragline. It has an effective operating radius of 100.6 m, a 50.5 m3 bucket, and weighs approximately 3860 tonnes yielding a ground pressure of III KN/m2•Figure 2 illustrates schematically the single pass mining sequence presently employed at the Genesee Coal Mine. The M8200 is used to lift all coal out of the cut, the coal being placed in stockpiles on the prepared pad .This method maximizes coal recovery under the conditions where spoil failures due to poor material would otherwise put men and equipment at risk. The coal is subsequently loaded by the coal shovel operating on the same bench as the M8200 dragline and delivered to the plant as required.All mined areas, as required under Alberta Legislation, are to be returned to an agricultural land capability equal to or better than that which existed prior to mining. Reclamation activities, as a result, are an important and integral part of the mining process. A complete list of the primary mining equipment deployed at the Genesee Operations appears in Table I."

Jan 1, 1994

By B. K. Gorain

"The Air-Metabisulfite (AMBS) process has been developed to treat complex copper, molybdenum and precious metals (gold, silver) bearing ores using brackish and sea water. This process was able to produce significantly better copper concentrate grades and higher recovery than possible using conventional lime and/or cyanide based processes for certain complex ores with high sulphide gangue minerals. The AMBS technology in now used commercially following a rigorous evaluation process emanating from laboratory curiosity to plant applications. In addition, many projects have embraced this technology at a feasibility level involving various complex ore bodies.This paper presents a summary of the findings from testing the AMBS technology on various ores types. Experiences gained from this successful development from bench to piloting and then to plant applications are also presented in this paper.INTRODUCTIONProcessing of sulphide copper, molybdenum and precious metal ores typically involves flotation of copper bearing minerals while depressing non-sulphide and other non-copper sulphide minerals such as pyrite, pyrrhotite and sometimes arsenopyrite. Though in many precious metal ores, the values are in these sulphide minerals as well. The conventional method employed in the industry to produce a saleable copper concentrate requires depression of these non-copper sulphide minerals using an alkaline pH above 9.5, though 10.5 to 11.5 is more common. Alkalinity is controlled by the addition of a pH modifier. Lime is normally employed as a pH modifier due to its relatively low cost; however, the costs associated with adding lime can be significant and the effectiveness of lime as a depressant could be drastically reduced when the process water supplied to the flotation circuit contains high level of dissolved salts. In some cases, a small amount of cyanide is used along with lime to depress non-copper sulphide minerals especially when its proportion to copper sulphide minerals in the ore is higher than three."

Jan 1, 2016

By M. S. Badollet

INTRODUCTION THE DEMAND for general knowledge on asbestos fibres has increased considerably in recent years. A few publications have printed data showing some of the physical and chemical prupertie3 of asbestos, but in many cases this information is difficult to find and is seldom available when needed. During the past ten years, Johns-Manville have received many inquiries on the physical and chemical properties of asbestos fibres. Fortunately, we had some of the information in our files, and we willingly supplied the data. To help relieve this need, we have tried to present briefly in this paper some of the interesting and out-standing properties of asbestos. This information was obtained over a period of years by search of the literature and by experimental investigations. PROPERTIES OF ASBESTOS FIBRES Table I (1, 2) presents, in convenient form for easy comparison, data on the principal properties of the several varieties of commercial 'asbestos' -actinolite, amosite, anthophyllite, chrysotile, crocidolite, and tremolite. Under each variety of fibre is a brief statement describing the properties in terms of structure, mineral association, origin, etc. Some of the more important data in Table I are expanded and presented in Table II (3). SOLUBILITY OF ASBESTOS A report ( 4, 5) discussing the effects of acids and caustic on asbestos fibres was published in Germany in 1927.

Jan 1, 1951

By Juliana Parreira

The past decade shows record increases in global demand for minerals and metals with an accompanying significant decline in skilled personnel. Mining companies today are examining new technologies to maximize production, reduce costs, and create safer work conditions to deal with this shortfall. Automation of an open-pit mine haulage system is receiving attention as a beneficial option since it provides more consistent and efficient operation of mining equipment, it removes workers from potential danger, it reduces fuel consumption significantly reducing greenhouse gas (GHG) emissions, and it can help optimize vehicle repairs and equipment replacement because of more-predictable and better-controlled maintenance. This paper describes a simulation model under development using the EXTENDSIM software package to examine scale-up issues and constraints of autonomous vehicles in comparison to a manual system. The software can predict and manage Key Performance Indicators (KPIs), such as productivity, safety, cost, equipment failures, fuel consumption, and tire wear under different road and load conditions. By breaking-down the various systems of an autonomous haulage truck and simulating the overall haulage system using a Monte Carlo approach, the model becomes a flexible and powerful tool to use within a mining organization. Direct comparison to a manuallyrun system can be done to show the cost and operational benefits of automation. Project managers can use this tool to guide decision-making about possible application of autonomous haulage trucks at a specific mine site.

May 1, 2010