Search Documents

By I P. W Chau

Construction of twin stacked railway tunnels through mixed ground conditions in the heavily populated urban environment of Hong Kong, including tunnelling in poor ground conditions, with low cover and under or adjacent to sensitive structures with minimal impact was the challenge presented by the tunnelling section of the Kowloon Southern Link project. This paper details how twin 1.1 km tunnels of 7.0 m internal diameter were driven by Mixshield tunnel boring machine (TBM) in mixed ground through one of the exclusive shopping and hotel districts in Kowloon. The paper addresses the challenges required to be considered and managed for the success of the project, including ground conditions, TBM selection, Mixshield TBM operation, settlement monitoring and control, ground- borne noise and vibration, proximity to utilities, buildings, roads and operating railways.

Jan 1, 2008

Fluid bed sulphation roasting of bismuth concentrates began at Warrego in 1980 in con- junction with the recommissioning of the Tennant Creek Smelter. This process, develop- ed by Peko Mines, is used to separate copper and bismuth by converting copper minerals to a water or weak acid soluble form and then leaching. Pilot scale testwork conducted at the Australian Mineral Development Laboratories (AMDEL) and by Dorr Oliver Pty Ltd in the USA indicated that close control of bed teaper- atures and exhaust gas composition was required to ensure high levels of soluble copper. After overcoming some initial problems, the plant now achieves typically 89 percent copper extraction. Plant capacity is 2.7 tonnes/h by design but in practice this is limited by feed analysis, air requirements, cyclone operation and calcine particle size Consideration.

Jan 1, 1984

Boring of a 7.5Km long tunnel under the city of Stockholm commenced in January, 1987. The 3.5m diameter tunnel will pass under the buildings and as no ground settlement is allowed, the regulation for water leakage into the tunnel is very strict. Probe drilling will be carried out continuously ahead of the boring and when water is encountered the rock has to be grouted before passing with the TBM. The tunnelling system enables probe drilling to be carried out during boring with the TBM. This has earlier been a capacity reducing factor as the whole operation has been stopped during probe drilling. The project is using a new generation TBM especially developed for hard rock formations which require higher thrust per cutter to get a high penetration rate.

Jan 1, 1987

By Marton A

The Readymix Group have a Quarry Improvement Program - 'Building in Quality (BIQ) which has many parallels to the ICI Explosives' total quality management - 'Quality Improvement Program' (QIP). Both companies have for some time recognised that the 'do it right first time' principle means less wasted effort and materials, that efficiency breeds profitability and so actively promote the quality culture. To install the principles and generate the culture requires considerable commitment and effort from the top down and invariably spreads to the suppliers and sub-contractors. Understanding the component processes involved with the quarry operation, analysis of those processes and gaining a breakdown of the cost of non conformance then allows the astute quarry operator to make the necessary changes to improve the process to realise profits. This paper outlines the steps in such a process and the profitable outcomes of the commitment to continuous improvement at the Nickol Bay Quarry.

Jan 1, 1994

Expert systems are a product of Artificial Intelligence (AI), a field of long standing, dedicated to the study of problem solving using heuristics, construction of symbolic representations of knowledge about the world, communications proce

Jan 1, 1998

By Kerr I. D, Kennedy M

Flash X-radiographs were obtained of commercial electric No 6 and No 8* strength aluminium tube detonators in small-diameter cartridges of emulsion explosive at various times after fusehead operation. The trigger system for the radiography was based on the detection of light following fusehead firing via optical fibres inserted into the fusehead cavity during detonator assembly. These experiments were simulated using a finite element hydrocode with realistic treatment of the non-ideal reaction kinetics. Excellent agreement was demonstrated for the shape and position of the shock waves. In both cases, initiation of the emulsion was predominantly forward from the detonator. For the No 8* strength detonator, this initiation resulted from the shockwave delivered through the sides of the detonator, while for the No 6 strength detonator, initiation was the result of a complex interaction between shockwaves originating both from the sides and from the endcap. In the reverse direction (towards the crimped end of the detonators), initiation was only weakly dependent on detonator strength, being controlled mainly by the competing processes of rarefaction from the cartridge boundaries and comer turning of the detonation wave from the forward initiation. The consequences for field performance of small-diameter emulsions will be discussed.

Jan 1, 1990

The Australian Mineral Industry has to compete on world markets, so its mineral research has to be aware of overseas developments, it must be of world class, and it must utilise as many ideas as possible in order to solve those problems that uniquely affect Australian minerals processing. North American mineral and resource research may be taken as a guide to world government, industrial, contract, and entrepreneurial research trends and ideas. A number of interesting findings are noted that may guide Australian developments and strategies for the future, in minerals research and exploitation.

Jan 1, 1986

By Lumley G. I, Duffy W. J

The risk involved with incorporating new/unfamiliar technology into mines has, in the past, largely been evaluated by the supplier of the technology. The implications on safety and productivity has been accepted as part of the process of `getting up and running'.This has changed. As companies see the lost productivity and accidents actually costing significant dollars, risk assessment is becoming an important part of the implementation of new equipment. Regulatory authorities are also seeing the preventable incidents and in some cases are now requiring a risk assessment to be undertaken on new equipment at a Mine.

Jan 1, 1992

By K L. Silversides, A Chlingaryan, A Melkumyan

Multiple data sources can be fused to improve boundary modelling in stratified deposits such as the banded iron formation (BIF) hosted deposits in the Pilbara Region of Western Australia. Accurate boundaries are essential to produce high quality geological models. Initial models are based on the widely spaced exploration hole data. This creates a high level of uncertainty in areas between the holes, with different interpretations of the boundary equally probable. Including directional information collected in these holes in the models can reduce the number of possibilities. Including data collected during mining, such as blastholes and bench measurements, can further guide the model. This research demonstrates a Gaussian Processes based method of fusing these disparate data sources to better inform the boundaries. Our results demonstrate that when only exploration points are used the model creates a smooth boundary with minimal variation between the holes. Each additional data source refined the model and added additional detail to the boundary. For the blast data, the new detail projects down to the bench below the current bench to allow for a better prediction before mining commences on that bench.

Mar 22, 2022

Gekko Systems Pty Ltd have developed the Python Underground Processing Plant for the concentration of gold and sulfide ores. The Python plant has an established flow sheet including fine crushing, screening, gravity separation and flotation which aims to concentrate the valuable minerals (gold/sulfides). The aim of the plant is to achieve high valuable recovery into a mass yield of 10 - 30 per cent to reduce the amount of material that is needed to be taken to downstream processing. This paper examines the test work protocol for testing an ore to assess its suitability for the Python flow sheet. This paper will discuss the test methods employed to determine crushing requirements, continuous gravity recovery and flotation performance and how the results relate to Python design for the comminution, gravity and flotation circuits. Results from past test work will be discussed.

Aug 1, 2010

By A Turner, P Hills, D Johnson

Underground mining for gold began in Beaconsfield in 1877 and development of the Tasmania Mine saw the sinking of multiple shafts, including the Hart Shaft over the ensuing 35 years. The mine closed in 1914 at a depth of 455 m due to prevailing economics, eventually reopening in 1999. The modern mine closed in 2012 after extending the mine from a historical depth of 455 m to the exhaustion of the modern Ore Reserve at a depth of 1210 m. West Tamar Council took over the lease for the immediate area around the Hart Shaft as an extension of the adjacent museum. The Hart Shaft and above ground structures became a significant drawcard for visitors. Tasmania was affected by sustained wet weather during May, June and July of 2016 which caused severe flooding and significant Statewide damage. This uncharacteristically intense wet weather caused saturation of the ground surrounding the Hart Shaft. Eventual shaft failure was first identified in August 2016. The failure of the shaft occurred at approximately 50 m below surface and resulted in a plug of material completely blocking the shaft. Significant surface subsidence affecting the surface infrastructure ensued. Due to the unstable nature of the surrounding material, it was determined that addressing the failure above the blockage would not provide a permanent solution to prevent the continued flow of material into the shaft. Many options to stabilise the shaft were considered, however it was assessed that a concrete plug in the shaft in competent ground at a depth of 100 m below surface and well below the blockage, would provide the only long-term solution. Man-entry was considered unsafe. The solution to access ultimately entailed filling the entire shaft with granular fill up to 100 m depth to act as formwork for a concrete plug. The rising mains at 400 mm and 250 mm diameter, which remained in place in the shaft, provided the avenue for placing the fill and ultimately, the concrete plug. Once the plug was in place the remainder of the shaft up to the underside of the blockage and over the top of the blockage to the surface was successfully filled with a combination of more granular fill and flowable cement stabilised sand. The Hart Shaft and surrounding above ground infrastructure was successfully stabilised and re-opened to tourist access. CITATION:Johnson, D, Turner, A and Hills, P, 2018. Stabilising and filling the Beaconsfield Hart Shaft, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 42–57 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Rabie A. S, Fouad K. M, Ammar A. A

The existence of Gabal El Kahfa ring complex, located in the Eastern Desert of Egypt, has been ascertained from aeromagnetic and aeroradiometric survey data as well as by aerial photography. Two maps for -the net aerial radiometric measurements reduced to ground level and aerial magnetic data corrected for the regional normal gradient of the earth's magnetic field have been constructed. The aeroradioactivity data have been interpreted geologically and analyzed statistically to outline various radiometric units and compute their charac- teristic statistics. The ring complex showed a circular radiometric feature and yielded a radiometric mean background and a standard deviation of 6.48 and 0.89 pR/h respectively. Besides, the observations showed a normal distribution. The aeromagnetic data have been reduced to the north magnetic pole, then filtered to produce the regional-and residual-component maps. Statistical trend analysis was conducted for the tectonic linea- ments resulting from the three magnetic maps, to define the structural framework of the area under study. This statistical study proved the exis- tence of trends in the east-west, northwest-south- east, northeast-southwest and north-south directions. The ring complex is characterized by a circular magnetic feature, whose average relief is 2150 nT. It is included within a high east-west trending magnetic zone. The latter represents a deep-seated uplift or anticline which is bordered from all sides by some faults of different trends.

Jan 1, 1988

By Donald D

A number of standard tests are conventionally carried out to characterise strength properties of rock. The values of the parameters obtained are often affected by planes of weakness or defects in rock structure. For the purpose of mine design, the range in values or the class of the strength (obtained from a number of tests) is generally more important than a precise value (obtained from a single or limited number of tests). Research has been conducted to establish a relationship between an indentation index and the strength of the intact rock material from the Eastern Goldfields of Western Australia. The Tamrock Raise Boring Index (RB-i) test, which is quick and easy to perform, was selected as the indentation test. The results show that, for heterogeneous, strong to very strong rock, there is a good correlation between the indentation index and the uniaxial compressive strength and tensile strength.

Jan 1, 1996

The Racecourse Orebodies at Mount Isa consist of a series of parallel steeply dipping lead/zinc/silver orebodies with a strike length of up to 1000 metres. Production from these orebodies between 13 Level to 9 Level has been by a series of cut and fill stopes in two level stages, leaving a crown pillar at 11 level. Development of the 15 level to 13 level extraction stage has recently been completed. The layout consists of a series of parallel stopes over a strike length of 1200 metres. Access to the stopes is by two declines connecting the stopes with a series of crosscuts This paper describes the basic layout with development and production methods employed.

Jan 1, 1977

By M Zlatev, S Silge

Producers of primary resources such as iron ore face the challenge of processing crude materials with increasing levels of impurities, which may result in the requirement for wet processing. This results in a significant increase in water usage, power consumption and operating costs. Given the remote locations of most operations in Australia (Stewart et al, 2013; Prosser, Wolf and Littleboy, 2011), the required volumes of power and fresh water for wet processing can be very difficult to achieve.HAVER&TYLER is renowned across the world for their screening technology in wet and dry processes. Its innovative Hydro-Clean® system represents a cost-effective and eco-sensitive way to clean any crude materials and material blends with a grain size distribution of 0–150 mm that are contaminated with adhesive clay, slit and other impurities.CITATION:Silge, S and Zlatev, M, 2015. Iron ore washing – achieve more with fewer resources, in Proceedings Iron Ore 2015, pp 519–528 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

For the past five years the University of Queenslandhas, through its various workshops, been preaching to Australia that there was a potentially hazardous situation from earthquakes for urban Australia. A few people outside The University accepted this, but largely the warnings fell on deaf ears.The 1989 Newcastle earthquake changed that per-ception. The most important lessons to emerge from Newcastle were (i)the realization that in continental areas small earthquakes cause widespread damage:(ii)the local geology of an area is of great importance in the damage done by an earthquake.These two factors clearly indicate that, in the future, we must take far greater account of the "Urban Geology" of an area. This paper discusses the need for urban geology and its impact on seismic risk and compares that with the traditional methods of assessing seismic risk.

Jan 1, 1990

By C K. McKenzie, P Popov, B E. Papillon, I Kharitonenko

Flyrock produced by blasts in surface mining and quarrying is a major hazard that can result in serious injuries or property damage. This paper presents a fully integrated and automated approach for reviewing blast outcomes from a wide variety of rock blasting environments from the perspective of flyrock safety associated with blasthole collar ejections. The process is applied at a corporate level for an explosives service provider handling up to 100 blasts per day from mines, quarries and construction sites throughout the US.Flyrock risk minimisation has inspired research and the associated development of a reliable flyrock model to estimate flyrock ejection velocities and the resulting maximum projection distances of fragments. In spite of significant achievements in this area, flyrock incidents continue to occur, mostly due to implementation mistakes. An efficient preventive measure is continuous blasting process improvement that relies on on-site video recording, storage, automatic analysis and classification of the recorded blasts followed by the automatic generation of reports.In this paper, a novel blasting video analysis system that is capable of processing a large quantity of video records is presented. Blast analysis and parameter measurement are fully automated and are carried out using videos recorded with a conventional consumer camera. The blast video recording process does not require the use of surface markers, range poles or objects of a predefined size for scaling purposes.Although automatic video analysis is commonly used in many application areas, such as video surveillance, traffic monitoring and robotics, the algorithms that have been developed to recognise and track solid objects with well-defined shapes, textures and colours are not efficient at dealing with blasts, which, by their nature, have dynamically changing parameters. Moreover, very strong camera vibration caused by blasts that cannot be totally compensated by camera image stabilisers may cause conventional computer vision algorithms to fail.This paper presents novel computer vision methods developed for automatic tracking of the trajectory from a blast ejection point to the highest point reached by blast particles and the ejection velocity. The system also uses colour and motion analysis to detect the emission of toxic fumes during a blast. The solution is vibration tolerant and can differentiate foreground and background data, even in the presence of camera vibration. Moreover, the blasting video analysis method can automatically categorise correctness of the measurements and therefore indicate cases when additional visual inspections may be required to verify reports generated automatically.CITATION:Kharitonenko, I, McKenzie, C K, Papillon, B E and Popov, P, 2015. An automated system for flyrock and fume monitoring of blasts, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 417–424 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D FitzGerald

A critical component of any new tunnel design in a complex geological setting is the development of an integrated three-dimensional (3D) geology model with a full set of geotechnical properties of the rocks present. A novel means of predicting the geology based upon sparse observations of structural geology at the surface and from drill holes has been developed and used in several major tunnel studies in Europe.An example of this is the Lyons-Turin twin rail tunnel which is still in a development phase. This tunnel has been in planning and development for over 15 years already. An important aspect of this work is to characterise geological uncertainty along various possible tunnel paths as an input into early design optimisations for time, cost and risk avoidance strategies. Once the tunnel works commence and more detailed geological data is collected by daily mapping, progressive refi nement of the geological model is desirable; geological conditions still to be encountered can be more accurately predicted. Faults and their offsets, dykes, geological unconformities, folding, as well as standard sedimentary processes are all correctly modelled in the software. It is important to allow for seamless interchange of geological models at various scales with CAD workflows so that sufficient detail can be readily accessed at the required scale. Also, the proposed tunnel in its correct geometry can become a ‘section’ in its own right. Progressive detailed local geology models in the vicinity of the advancing head are created from the regional scale work by cutting and pasting a starting model, then adding all the extra detail for the required engineering geology work.For all rocks, most standard geotechnical quantities such as sonic velocities, Young’s modulus and Poisson’s ratio are handled. These and any other phenomena from borehole observations can have variograms calculated and stratigraphically constrained estimations made in a least biased geostatistical manner, in advance of the tunnel. RQD, or a prediction of rock fractures, is handled by the faulting and folding modelling facilities. This is probably the more interesting issue to pursue, as the fractal nature from small scale fractures and joints, to large-scale faults, can now be characterised more convincingly.

Mar 8, 2011

By T Belligoi

Diamond cores and drill chips provide the only direct physical evidence for ore containing rocks. Early characterisation of cores and drill chips is important as it provides critical information for downstream processing. Traditional characterisation techniques include visual logging by a geologist or analytic and spectroscopic methods but they are time consuming and can miss some important textural or geomechanical features.The goal of this work is to evaluate the application of image analysis to iron ore cores and drill chips and to suggest improvements to existing core-scanning and chip monitoring systems. Two samples of massive ore differing by their mineralogy and texture, as well as two different batches of drill chips, have been imaged and analysed. Results are compared in function of the imaging system and the classification algorithms.As a conclusion, despite the necessity for more testing and improvements in calibration and lighting, it is obvious that image analysis technologies can bring a lot of useful information in the perspective of a geometallurgical mapping of the deposit.

Jul 11, 2011

By X Yang, T Zhang, Z Li, Z Yan, M A. Williams, S Qin, P Wilson

Continuous development of complex new steel grades to meet the ever-increasing demand of high performance causes recurrent issues in steel continuous casting such as surface quality defects (eg cracks, depressions, deep oscillation marks) and productivity challenges (eg faster casting, near-net shape casting). Continuous casting of steel is a highly successful metallurgical process. Much of this success can be attributed to the performance of the casting powder that is added to the top of the mould, creates a liquid slag pool as it is heated, and forms a slag film between the watercooled copper mould and steel shell during its passage down the mould. Mould powder selection is a compromise between the conflicting requirements of heat transfer and lubrication. In an EU RFCS (Research Fund for Coal and Steel)-funded project, various techniques are developed to offer the opportunity to adapt the slag film to meet the conflicting needs in different parts of the mould such that mild cooling can be generated in the meniscus, mid-broad face or corner areas whilst maintaining lubrication and offering higher cooling rates in other areas of mould. This has significant potential to address the industrial issues in product quality and productivity of continuous casting. This paper reports, as part of the EU RFCS project, the determination of crystallinity and porosity in slag films for casting challenging and innovative steel grades using new methods. In comparison with the methods such as X-ray powder diffraction (XRD) analysis and optical microscopy / scanning electron microscopy (OM/SEM) analysis that are currently adopted by the industries, EBSD (electron backscatter diffraction) has been employed to determine the crystallinity of the slag films taken from industry casters. X-ray computed tomography (XCT) plus 3D image reconstruction has been used to determine the slag film % porosity with pore volume, pore size distribution, and pore location, which can be linked with the performance of the slag films during casting different steel grades.

Jun 19, 2024