Search Documents

By Wallace W. Wilson

This DaoerAA calls to attention for the first time, to the writer's knowledge, a purported recovery of oil by substantially horizontal gas cycling that is considerably in excess of 50 per cent of the oil originally in place. The average angle of dip along the path of travel of the gas is less than one degree of arc. The best recovery by gas cycling previously brought to the writer's attention1 occurred in the case of the Mile Six Field in Peru, where about 68 per cent of the original oil in place has so far been recovered. In this case, however. the recovery was greatly aided 1)y the high dip angle of about 17.5". An approximate estimate of recovery was made by the method developed by the writer' for the case of the Cook Ranch Field, using an average relative permeability ratio function dictated by past experience with a number of good quality sandstones. A result of about 40 per cent recovery of the original oil in place wa* obtained after the 8.5 pore volumes of cumulative gas cycling undergone by the Cook Ranch Field. Tile writer desires to emphasize what appears to him as the sound engineering practiced at Cook Ranch, and also the care attending the taking of data and the high quality of the calculations made. It is impossible to take issue on factual grounds with any of the conclusions drawn in the paper. It is, however, desired to point out the difficulty of explaining the unexpectedly favorable oil recovery on ordinary theoretical grounds. It would be of interest to know whether relative permeability ratios have been measured on the Cook sand. The operator is inclined to attribute some of the excess benefit to settling of the oil across the bedding planes into the lower part of the sand. It is difficult for the writer to appreciate the importance of such an effect, inasmuch as the concomitant opening of excessive vacated pore space in the upper part of the sand would he expected to cause excessive bypassing of the gas. REFERENCE 1. Welge. H. J.: "A Simplified Method for Computing Oil Recovery by (Gas or Water Drive." Trans. AIME, (1952), 195, 91. AUTHOR'S REPLY TO MR. WELGE Welge has poined out clearly the difficulty of applying material-balance procedures in calculating the Performance of low-pressure, dispersed gas injection operations. There can be no argument that even with the most favorable assumptions of K,/K,, and with cumulative gas cycling in excess of normal expectations, the calculated oil recovery will be considerably less than the 72.5 per cent recovery realized from this project to Jan. 1, 1951. There probably are at least two reasons for the unusually high recovery from this reservoir, the effects of which would be difficult or impossible to calculate by known methods: 1. The operator did not use the same injection wells for the entire operation, and exercised considerable control over producing GOR by changing the locations of injection wells whenever well performance indicated excessive bypassing. Fifty-six wells were used for injection, not over 29 of which were in use simultaneously. This procedure resulted in frequent shifting of the fluid movement patterns in the reservoir and undoubtedly increased the ultimate recovery. The writer knows of no satisfactory procedure for calculating the effect of this practice. 2. Vertical movement of oil across the bedding planes of the reservoir rock hy gravity drainage tended to maintain a relatively high oil saturation, and hence a favorable K,/K, ratio, in the lower sections of the reservoir. As pointed out by Welge, this condition has aggravated the tendency for high producing GOR, but at the same time it has resulted in increased oil recovery. As may be seen from the performance charts for the various battery areas, operating (GOR'S have been quite high for the last several years of reported history.

Jan 1, 1952

By N. G. Johnson

ALL of us are only too familiar with the fact that first the defense program, and finally the war, required vastly increased production from existing sources, and the discovery and development of new sources of minerals and metals. For this vast program, the explosives industry was well prepared. I use the term "well prepared" to cover all the phases of explosives service, which include formulation, design, manufacture, distribution, and application.

Jan 1, 1944

US 4,181,520 - Direct reduction of iron oxide ore to sponge iron in a rotary kiln. Ore is fed into the kiln along with coal briquettes and passed through a preheating zone and then a reducing zone countercurrent to the flow of a kiln atmosphere which includes air or other oxygen-containing gas. The agglomerated coal is heated at such a rate that it disintegrates into fine particles in the preheating zone. The coal is largely recovered for reuse, while reduction is effected with a reducing flame rather than the coal. G. Reuter and W. Schnabel, assigned to Metallgesellschaft AG. Jan. 1, 1980. 6 pp. (75-36). Filed- 10-19-78 (952,870). Priority: West Germany, 1-14-75 (2,501,182). Same: British 1,532,969, dated Nov 22, 1978.

Jan 1, 1982

By John T. Norton

FoR many years the copper-bearing steels have been of considerable interest to the metallurgist because of their corrosion-resistant properties. More recently the discovery of their definite age-hardening characteristics has focused attention on them again. In a recent paper, Smith and Palmer(l)† have given an admirable description of the behavior of a considerable number of steels of this type and a study of their results suggests two questions of a more or less fundamental sort. In the first place, it has been plainly shown that the hardening effect of added copper does not increase up to the maximum solubility of copper in iron as given by earlier investigators, but reaches its greatest value considerably below this point. This fact suggests that either the solubility is not so great as previous investigators have stated, or that the age-hardening mechanism is not the simple precipitation phenomenon that has been postulated. In the second place, the nature of the aging mechanism in this particular system should be determined. Recent developments in the study of age-hardening processes have shown that the increase of hardness is often, but not always, accompanied by precipitation and the action of a particular system is not predictable on the basis of its components or type of phase diagram. It would be of considerable interest to study the aging of the iron-rich iron-copper alloys in detail. One would like to know whether the aging mechanism is different at high and low aging temperatures, and whether the extreme sluggishness of the system may perhaps represent some new type of aging process. The experiments to be described were carried out in an endeavor to answer these questions. Obviously, in such experiments it is important to confine the hardening effect to the single element, copper, so that iron and copper of high purity must be used in the preparation of specimens. An observation of lattice changes during the aging process, correlated with the hardness changes, seems to be the best available method of

Jan 1, 1935

By John T. Norton

FoR many years the copper-bearing steels have been of considerable interest to the metallurgist because of their corrosion-resistant properties. More recently the discovery of their definite age-hardening characteristics has focused attention on them again. In a recent paper, Smith and Palmer(l)† have given an admirable description of the behavior of a considerable number of steels of this type and a study of their results suggests two questions of a more or less fundamental sort. In the first place, it has been plainly shown that the hardening effect of added copper does not increase up to the maximum solubility of copper in iron as given by earlier investigators, but reaches its greatest value considerably below this point. This fact suggests that either the solubility is not so great as previous investigators have stated, or that the age-hardening mechanism is not the simple precipitation phenomenon that has been postulated. In the second place, the nature of the aging mechanism in this particular system should be determined. Recent developments in the study of age-hardening processes have shown that the increase of hardness is often, but not always, accompanied by precipitation and the action of a particular system is not predictable on the basis of its components or type of phase diagram. It would be of considerable interest to study the aging of the iron-rich iron-copper alloys in detail. One would like to know whether the aging mechanism is different at high and low aging temperatures, and whether the extreme sluggishness of the system may perhaps represent some new type of aging process. The experiments to be described were carried out in an endeavor to answer these questions. Obviously, in such experiments it is important to confine the hardening effect to the single element, copper, so that iron and copper of high purity must be used in the preparation of specimens. An observation of lattice changes during the aging process, correlated with the hardness changes, seems to be the best available method of

Jan 1, 1935

By W. J. Locher

One important means of reducing steel consumption in grinding mills is not mentioned in S.G. Malghan's paper. It is simply to reduce the oxygen content in the mill and pulp. While oxygen dissolved in pulp is not readily reduced without additives, reduced aeration and reduced ventilation of grinding mills are often feasible. It is not necessary to completely eliminate the oxygen to achieve substantial benefits, since corrosion rates vary with oxygen content in a manner analogous to combustion rates as oxygen content increases. It is difficult to generate indisputable quantitative data on the relationship of oxygen reduction in a milling system to changes in consumption of grinding steel. Perhaps this accounts for the absence of technical papers on the effects of reducing oxygen content in grinding mills by reducing aeration of pulp and ventilation of grinding mills. One qualitative observation is that mills operating at a lower percent of critical speed will tend to have lower media consumption for similar fineness of grind without necessarily having an equivalent reduction in power consumption per ton of product. Reduced mill speed would also tend to reduce both ventilation of the mill and entrainment of air in the pulp. Larger grinding mills tend to be more media efficient because they operate at a greater ratio of charge volume to pulp surface area, which will tend to reduce the aeration per unit of pulp volume. The mechanical steps required to reduce aeration of grinding mill pulps depend on the configuration of the grinding circuit and related process. Reply by S.G. Malghan Mr. Locher stated that my paper did not mention the reduction of oxygen content of the pulp as a potential method of decreasing the steel consumption. I would like to bring to the attention of Mr. Locher that an indirect reference was made to the fact that pulp oxidation potential controls the corrosion wear of steel. Though dissolved oxygen is one of the factors that controls oxidation potential, additional discussion was deliberately avoided for the reasons mentioned by Mr. Locher. The most important reason being the difficulty of decreasing and controlling the oxygen concentration of the pulp in a commercial mill.

Jan 1, 1984

By Sheldon P. Wimpfen

RESEARCH is undertaken to find out what must be done when what we are doing now is no longer adequate. To accomplish this end, researchers apply the truths of nature to industrial evolution. A survey conducted with the co-operation of 58 universities and colleges offering degrees in mineral engineering was the basis for the table accompanying this article. This survey was undertaken with the object of presenting to faculties and student bodies, as well as to industry, all available information on what action the educational institutions of the country have taken to provide the properly trained researchers so vitally needed. A hoped for result is that the great variety of opportunities available will encourage some undergraduate students to continue in their field beyond attainment of a B.S. degree.

Jan 1, 1947

G. D. Kneip, Jr., and J. 0. Betterton, Jr. (Union Carbide & Carbon Corp., Oak Ridge, Tenn.)—The authors have contributed to the theory of zone melting by considering the effects of the solidification of the final zone on the distribution curves for the finite length bar. However, they do not consider in sufficient detail the restrictions imposed by the particular metals involved. Eq. 4 has the analytical solution which is equivalent to Pfann's' equation for normal solidification of the final zone. For distribution coefficients less than one, it is apparent from this form of the equation that, as the solidification approaches completion, the concentration attains extremely large values which are inconsistent with the density of physical materials. The necessary restrictions then are that the solute concentration cannot exceed the density of the alloy, or more frequently, the solubility limit in the solid phase. Secondly, the distribution coefficient cannot be constant from 0 to 100 pet solute unless the liquidus and solidus coincide over this whole region. It would thus be more correct to impose limits on the solubility such as would be indicated by a typical eutectic diagram. Furthermore, in this case the assumption that the distribution coefficient remains constant is more likely to be realized. Eq. 4 should then be replaced by the following C,,(x) =k/L-x [ ?11 3 C11 (x)Ddx - ?11 4 Cn(x)dx= k[Cn (L-l)/k] [ L-x/l]x-1 L-l = x = L-l [kCenterlie/Cn (L-l)]1/k-1 The typical shape for the distribution curve in the final zone is indicated schematically in Fig. 12 for the simple eutectic case. The solidification proceeds according to Pfann's' expression until the concentration reaches the maximum solubility in the solid phasc. At this point, the concentration changes abruptly to the eutectic composition and remains at this value for the duration of the solidification. The width of the flat region, and the back reflection of this effect into the concentration curve on subsequent passes, depends upon the ratio of the eutectic concentration to the original concentration, upon the distribution coefficient, and upon the number of passes. Similar effects on the concentration curves in the first zone length would be expected in many systems for which the distribution coefficient is greater than one, and where the maximum solubility is not too much larger than the original concentration. The discussers agree with the authors that the assumption that the liquid is uniform in concentration should be considered with caution. Kneip and Better-ton' have shown, however, that in floating zone refining of zirconium, using induction heating, the distribution of iron agrees with theory which assumes a uniform liquid composition. Hence, in this case, the experimentally realized distribution coefficient agrees with the present phase diagram within the experimental uncertainty. L. Burris, Jr., C. H. Stockman, and I. G. Dillon (authors' reply)—The authors are happy to have received the comments of G. D. Kneip, Jr., and J. 0. Betterton, Jr., which provide additional insight into the zone refining process. It is true that the equations developed are inapplicable if the solute solubility in the solid phase is exceeded. However, this restriction on the use of the equations was clearly stated in the paper. A closer approach to

Jan 1, 1957

By Francis Flynn

MANY excellent papers, descriptive of the milling and smelting of every kind of commercial ores, the refining of virgin metals, the casting into various shapes demanded by the trade, the rolling into shapes best suited to the factory machinery and the making of composition alloys to suit every requirement have been issued by the many technical societies dealing with non-ferrous metals. It is a wonderful collection of papers, of which the mining and metallurgical engineers may well be proud, but strange as it may seem, metallurgists in general appear to take the stand that when they have delivered suitable alloys to the foundry and rolled products to the factory their duty to write papers has ceased, at least in so far as the A. I. M. E. is concerned. Still we read in the daily papers that the mining companies are absorbing metal-manufacturing industries. The purpose of this paper is to describe the reclaiming of non-ferrous scrap metals at manufacturing plants, taking as an example the automobile industry.

Jan 1, 1929

New Products Equipment

Jan 6, 1953

By W. J. Helfrich, R. A. Dodd

Binary aluminum solid-solution alloys containing various amounts of silver, magnesium, and zinc were prepared by careful directional solidification, and the hydrostatic and X-ray densities were compared. With the exception of the Al(Ag) alloys, the X-ray densities were consistently greater than the hydrostatic measurements, in agreement with earlier observations by Ellwood. In contrast to Ell-wood's interpretation in terms of vacant lattice sites associated with Brillouin zone effects, a tentative explanation based on the existence of solidification microshrinkage was favored. This hypothesis was confirmed by an examination of Al(Zn) alloys prepared by vapor diffusion of zinc into aluminum. The hydrostatic and X-ray densities were now in very close agreement, and it was concluded that the filling of Brillouin zones in aluminum solid-solution alloys does not necessarily result in the formation of defect structures containing an excess of vacant lattice sites. ThE existence of defect structures of the vacancy type in alloys in which the excess vacancies have an electronic rather than a thermal or mechanical, and so forth, origin is well recognized. Examples of incomplete lattices of this type are to be found in the Ni-Al,1-3 Fe-Ni-A1,4 c~-Ni-Al,5 Fe-Cu-Al,= and Co-A17 systems. These defect structures are of a special kind in that the intermediate phases possess an ordered atomic arrangement or superlattice, and in some instances the vacancy concentration may be unusually large, e.g., at 45.25 at. pet Ni in NiA1, approximately 8.8 pet of the lattice sites are unoccupied. Ellwood8-10 has reported similar defect structures in the aluminum solid solution alloys of the Al-Zn and A1-Mg systems and in alloys of the Au-Ni system." In Al(Zn) the (apparent) vacancy concentration rose, somewhat irregularly, to a maximum of about 2 pet vacant sites at 25 at. pet Zn, while in Al(Mg) the (apparent) vacancy concentration increased continuously to 1.7 pet at 15 at. pet Mg. An explanation in terms of Brillouin zone overlap was attempted, although Pearson12 has pointed out the difficulty of reconciling the observations with zone theory. However, the possibility of the effect being caused by the Fermi surface just touching a plane of energy discontinuity inside a prominent Brillouin zone has, in general, been accepted. In fact, Massal-ski13 has interpreted Ellwood's8 observations as confirmation of Leigh's14 theoretically predicted zone overlap occurring at approximately 2.67 electrons per atom. Unfortunately, Massalski was apparently unaware that Ellwood9 had revised his earlier results considerably, and the revised data did not confirm Leigh's analysis. Ellwood's clata were reexamined by the present authors who noted a possible correlation between the percentage defects as a function of alloy composition and the temperature interval of solidification measured from the respective equilibrium diagrams. This suggested an explanation in terms of shrinkage porosity rather than vacant lattice sites, and pointed to the desirability of reexamining appropriate alloy systems using: both Ellwood's method of specimen preparation (casting followed by wrought fabrication) and alternativ'e methods, i.e., diffusion, which might be expected to minimize, or even completely obviate, microporosity. ALLOY PREPARATION 1) Cast Allolys and Aluminum Single Crystals. Al(Ag), Al(Mg;l, and Al(Zn) alloys of various compositions up to 20 at. pet silver, 13.5 at. pet mg, and 30 at. pet Zn were prepared by melting under helium and casting into graphite molds. In the first two systems, the maximum alloying addition was quite close to the limit of solid solubility, but the possibility of transformation to a' during quenching somewhat restricted the suitable Al(Zn) composition range. The alloys were prepared from high-purity aluminum, a lot analysis showing 0.002 wt pet Cu, 0.002 wt pet Fe, and 99.996 wt pet A1 by difference. The silver, magnesium, and zinc were of 99.99+, 99.98+, and 99.998 wt pet respectively. Each composition was analyzed chemically. The as-cast ingots measured 7/16 in. diam and 5 in. length. One in. was removed from the top of the ingot, and the bottom 3 in. was machined to 0.275 in. diam; a point was also machined on the smaller diameter end. The remainder of the original ingot served as a top riser during subsequent remelting and controlled solidification. The machined ingots were now remelted using a Bridgman soft-mold technique to ensure directional solidification and, therefore, a minimum of micro-shrinkage. Alumina powder was used as mold material contained in an alundum thimble, and this crucible was placed in a helium-filled Vycor tube. The assembly was lowered through a suitable temperature gradient at approximately 0.5 in. min-l, and the risered portion of the casting was subsequently removed by sawing.

Jan 1, 1962

By J. B. Ackerman, J. D. Miller

Alunite [KA13(S04)2(OH)6] is a promising non-bauxitic aluminum resource, the domestic reserves of which are estimated to be 800 x 106 tons at 35 percent alunite. The major gangue mineral associated with alunite is quartz. The thermochemical process that has been developed for treatment of this ore does not provide for the initial removal of gangue prior to processing. In this regard, it may be desirable to concentrate the ore to gain significant technical and economic advantages. Experimental results indicate the effectiveness of an oleic acid flotation technique and exemplify the problems encountered in fine particles processing. These results show that the quality of separation studied as a function of temperature, collector addition, and depressant addition is dependent on the degree of liberation achieved during size reduction. At coarse grinds the quality of separation was limited by the presence of locked particles while for finer grinds where more extensive liberation is achieved, better separations were obtained. The degree of liberation for each size interval was determined by an SEM/energy dispersive x-ray technique and found to be independent of the extent of size reduction, suggesting that liberation occurs by indiscriminate fracture and not by detachment. Up to 89 percent liberation was realized for a minus 400 mesh grind. Under these circumstances, the quality of separation appears not only to be limited by the remaining locked particles, but, also, by contamination of the alunite concentrate with fine quartz gangue (< 2µm). The best separation for the minus 400 mesh grind was a rougher recovery of 88 percent with a grade of 65% alunite at 50°C.

Jan 1, 1980

By C. Feng

HE sensitivity of twinning in molybdenum alloys containing 20 or more at. pct Re was reported by Dickenson and Richardson&apos; and Sims et a1.&apos; The latter3 also studied the effect of twinning on plastic deformation of these alloys. Recently, in this laboratory, the twinning planes in a series of Mo-Re alloys were successfully identified by tracing their boundaries on two known surfaces of the crystals, with the aid of stereographic projection. The nominal alloy composition and the results of the determination are listed in Table I. Metallic powders of molybdenum and rhenium with 99.9 pct purity were mixed, pressed and arc-melted into buttons under purified argon in a water-cooled copper hearth; the buttons were annealed at 2400 °C in vacuum (10-&apos;mm Hg) for 1 hr, remelted under argon and finally reannealed in vacuum at 2400°C for another hour. This treatment yielded a homogeneous alloy. Large-grain specimens devoid of subgrains were obtained with grain diameter varying from 1/8 to 1/2 in. A typical specimen weighed about 15 g. Orientations were determined by taking X-ray back reflection photographs for each grain on a polished surface of the specimens. Two surfaces were cut and polished; the angle between the two surfaces was measured with an accuracy of *2o. The twins were produced by compression in a hydraulic press at room temperature. Usually, several sets of twins could be obtained within each grain. Except in cases where no twins were formed, (Crystals 7, 8, and 9) the twinning planes were identified consistently as the (112) family over a wide range of alloying compositions and surface orientations of the crystals, as indicated in the stereo-graphic triangle in Fig. 1. The twins, however, were not broad enough to accommodate a conventional X-ray beam and no identification could be made of the twinning direction. Nevertheless, the direction must be one that lies in a plane of symmetry perpendicular to the twinning plane. There are only two such possible planes in a bcc lattice, namely the (110) and the (100) planes. Of these, only the (110) planes are perpendicular to (112), and the <111> direction is the intersection of the two perpendicular planes. It can thus be concluded that <1l1> is the twinning direction. The twinning elements of molybdenum have been reported as the (112) planes and the <111> directions,4 which are also the operative elements in other body-centered-cubic metals, such as W, a-Fe, and ß -brass.5 Thus, the present finding of the twinning elements in Mo- Re alloys supports the concept that twinning formation is mainly governed by the lattice structure. It is of interest to note that for specimens containing 12 at. Pct Re or less, no twins were found after being plastically deformed to as much as 30 pct reduction in height by compression, while for the 35 at. pct Re alloy, twins were formed with less than 1 pct deformation. This, of course, does not exclude the possibilities that for Re-Mo alloys containing 12 pct Re or less, twins could be formed under different conditions, such as at liquid air temperature or under impact loading. The present results, however, suggest that under the same conditions twinning is increasingly sensitive with increasing rhenium content. Consequently, the plastic strain at which twinning starts was found inversely proportional to the amount of rhenium in solid solution with molybdenum. This plastic strain necessary to cause twinning may be used as a criterion in the study of twinning characteristics.

Jan 1, 1961

By AIME AIME

ON April 7 the twentieth national Open-hearth Conference of the A.I.M.E. will be held in Birming¬ham, Ala., in conjunction with a meeting of the Committee on Blast Furnaces and Raw Materials. At least 300 engineers and operators are expected to attend. Birmingham, the industrial city and iron, and steel center of the South, has been called the "Magic City." Men actively engaged in business in Birmingham today have seen practically every building in the business district erected, have witnessed the establishment of every existing industry, and have hunted birds cm the site now one of the busiest corners of the business district. Incorporated as a town in 1871, the city today has a population of more than 380,000 in its metropolitan area. It is

Jan 1, 1937

By Lars Rossemyr, Terkel Rosenqvist

The equilibrium Mn + 2 IiCl = MnCl2(g) + H2 has been studied at 1090°C for pure manganese and for Mn-Si alloys. For this reoction a standard free energy of Fo1363, = - 19,700 i 300 col ioas found. Combined with other thermal data, the standard free energy of the reaction Mn(s, ß) + Cl2 = MnCl2(g) was derived: Fo=- 56,140 + 9.78 T log T - 40.10 T For the formation of the various manganese silicides the following free energies were obtained. 5 Mn + 3 Si - M1z5Si3 ?F°1363 = -41,500 i 1500 cal Mn + Si - h.lnSi ?F°1363= -10,000 i 500 cnl Mn + 2 Si = MnSiz ?F°1363= -11,500 ± 500 cal In the search for a method suitable for the study of thermodynamic properties of certain alloy systems, it was found that the heterogeneous equilibrium between the alloy and a gas mixture consisting of hydrogen chloride, hydrogen, and volatile metal chlorides has considerable advantages. In addition to giving thermodynamic information about the alloys, such measurements may be used to derive thermodynamic data for the volatile metal chloride itself. The present paper gives some results which were obtained for manganese silicides and manganous chloride. Similar studies are presently being carried out for the iron silicides. The phase diagram of the Mn-Si system is rather well known,&apos; but no information exists to the authors&apos; knowledge about the thermodynamic properties of manganese silicides or about the chemical activities in molten Mn-Si alloys. At elevated temperature, manganese may react with hydrogen chloride according to the equation: Mn(s, ß ) + 2 HC1 = MnC1, (g ) + H2 [ 1] with the equilibrium constant The value of K, may be determined from measurements of the gas composition in equilibrium with pure manganese. When this value is used in connection with measurements on manganese alloys, the chemical activity of manganese in the alloy may be derived. Initial calculations showed that around 1000" to 1200°C the equilibrium constant K1 has a value of a few thousand, i.e., the reaction is shifted far to the right. In order to study this rather unbalanced gas composition, a flow method was used in two slightly different modifications. For all experiments with manganese silicides and for some experiments with pure manganese the apparatus shown on Fig. 1 was used. A bed of the metal or alloy was placed in a tube furnace. The refractory tube had an internal diameter of 14 mm and the bed was 75 mm long. Electrolytic manganese of high purity and silicon, 99.95 pct Si, were used as raw materials. All alloys were prepared by melting weighed amounts of the elements in a high frequency induction furnace in argon atmosphere. The melting was done in a silica crucible which was placed inside a graphite shell. The alloys were crushed to - 10 +40 mesh and analyzed chemically. Also, for the pure elements, the same size fraction was used. A controlled gas mixture of purified hydrogen and from 3 to 12 pct HC1 was passed through the bed where it reacted with manganese according to Eq. [I]. The volatile manganese chloride was collected in a condenser placed in the cooler part of the furnace tube. The gas mixture before and after the furnace was sampled and analyzed by absorption of

Jan 1, 1962

By Dewey J. Sabin

THE Rio de Canada Honda placer property is situated at an altitude of 5500 ft. above sea level in the San Luis Mountains of the Province of San Luis, Argentina. The mine is reached by 70 km. of fair truck road, from the nearest railway station on the Ferrocarril Buenos Aires al Pacifico. The Pan-American airport at Villa Mercedes, 1.40 km. distant, serves as the most convenient point for shipment of gold. Placer mining in the Rio de Canada Honda dates from the time of the Incas and the present native population depends on the gold washed from this river and the adjacent arroyos as a means of livelihood as did the many generations before them. They dig pits to bedrock where they are not driven out by water, and mine the bedrock gravel by means of tunnels and caves. No timber is available and the ground is supported by rock cribs carefully built with the boulders encountered; or with angular blocks of slate rock taken from quarries on the surface.

Jan 1, 1936

By G. V. Cullen, N. G. Siviour

It has previously been reported that metal loadings of up to 6.8 m. eq/g. of dry coal can be obtained by contacting brown coal or lignite with ammoniacal solutions of ammine forming metals. Application of equilibrium expressions to further experimental results indicates that the extraction is by ion exchange, that the exchange is divalent-univalent for Zn, Cd and Ni, but is mainly univalent-univalent for Cu, and that to obtain reasonably uniform values for the equilibrium constants correction formulae must be applied to compensate for multiple functionality of the coal and its pH dependence in ion exchange. The results are shown to be consistent with the hypothesis that metal ammine complex cations are exchanged for protons derived from carboxyl and/or phenolic hydroxyl groups in the coal.

Jan 1, 1981

By A. L. Field, P. H. Royster

Bureau of Mines Technical Paper 189 consists of a record of the scientific data obtained in the iron blast-furnace slag investigation which is reported in Technical Paper 187, "Slag Viscosity Tables for Blastfurnace Work." It includes a description of the method of preparing the synthetic melts, construction of an improved electric furnace, and refinements in laboratory methods of measurement. Only the general features of the work and the conclusions drawn from the experimental data can be given attention here. Silicates in the Liquid State In the manufacture of refractories, Portland cement, glass, and porcelain, and in pyrometallurgical operations, importance attaches to the behavior of-silicate compounds at temperatures beyond the range of common experience. This field of research has not been investigated as carefully as its scientific and industrial importance would seem to warrant. Probably the most important of the unsolved problems in the chernistry of silicates is the question of their stability in the liquid state. That little progress toward the solution of this problem has been made is not strange if there be borne in mind the difficulties attending experiments made at temperatures at which silicates become fluid, and the comparatively short time since it became possible to measure these temperatures. On the other &apos;hand, considerable progress has been made in the study of the compounds in the solid state because of the directness and simplicity of methods of optical examination. Important advances have been made by the Geophysical Laboratory at Washington in recent years. An extended study has been made there of saturated solutions representing a considerable number of binary and ternary systems of the more common refractory oxides. The methods

Jan 1, 1918

By J. B. Newsom

During July and August, 1931, the Bloomington Limestone Co., at Bloomington, Ind., ran a single wire saw on ledge No. 2 at Maple Hill quarry. The ledge was hard rock, much harder than the average Indiana limestone. It was opened at two ends for a depth of about 20 ft., leaving a 130-ft. section between. During the tests 21 cuts were made in this ledge, to an average depth of 10.42 ft., for a total effective cutting area of 28,445 sq. ft. The actual area sawed was about 20 per cent higher, as we did not level down in the center, preferring to cut deeper on the ends. The various cuts were carefully logged, and the results plotted. A study of these results is interesting, as it enables a forecast of probable future costs to be made, and also because it points out the limitations of wire saws, and the lines development should logically take. Some of the inferences to be drawn are discussed below. Best Length of Cut.—No trouble was due to length of cut, except that we could not easily level down a long cut, and it is probable that longer cuts, say up to 200 ft., can be made. Obviously, longer cuts will result in a higher sawing rate in square feet per hour if they do not cause stoppages. Working Higher Ledges.—The cuts averaged 10.42 ft. high by 130 ft. long. A study of several logs indicated that during only about 15 per cent of the cutting time was the saw cutting to its full efficiency; that is, during about 85 per cent of the time the saw was bedding in at the ends and not cutting well in the center, or the ends were below the floor line and only part of the wire was doing effective cutting. This does not mean that the wire was cutting to only 15 per cent of its capacity, but it means that during about 85 per cent of the time part of the cutting was being wasted. If higher ledges had been worked, the wire would have cut to its full efficiency a large part of the time, as it would have had a greater distance to saw after it had bedded in to the ledge before the ends went down below the floor level. The exact saving to be expected cannot be calculated, but it would be large if really high cuts were made.

Jan 1, 1932

By L. H. Marshall

MALLEABLE-IRON castings frequently are made brittle by hot-dip galvanizing. The castings may be and usually are perfectly normal before the hot-dip treatment, in that they will stand a remarkable amount of distortion and punishment before fracturing, yet, after galvanizing, a single blow with a hammer will often cause a break. One such casting broke when accidentally dropped on a concrete floor. Such weakness causes galvanizers to view malleable cast iron with misgivings, and, in turn, is a source of worry to the manufacturer of the castings. It is felt, therefore, that a practical method of overcoming this embrittlement, a method that has already been used on several thousand tons of castings, will be of general interest. The purpose of this paper is to describe this immunizing process. DEVELOPMENT OF THE PROBLEM In the early days the trade was not much concerned with the finish of the castings and in most cases the only protection given to the parts placed in service was a coat of paint. It was soon found that this form of protection was inadequate and the user demanded a better type of rustproofing. In compliance with this demand, the use of zinc for coating gradually spread until it became general practice. More than half of all the zinc produced today is used for coating iron and steel, and, in spite of the recent use of cadmium and chromium, zinc coatings are still recognized as among the best general rust inhibitors for atmospheric exposure.

Jan 2, 1926