Search Documents

By J. G. Cullain

Inco Limited is an integrated mining, smelting, refining and manufacturing company with operations located worldwide. The Ontario Division operations consist of 13 mines and 10 processing facilities located in Sudbury, Port Colborne and Shebandowan. The scope of our utilization of energy in the Ontario Division in 1976 included in excess of 2.2 billion kilowatt hours of electric power, 12 billion cubic feet of natural gas, 60 million Imperial gallons of residual oil and smaller quantities of other fuels. In addition to the primary energy consumption, waste-heat energy is recovered in various operations throughout the Division, thereby reducing our primary energy requirements. Total expenditures for primary energy alone in 1976 exceeded 60 million dollars. Energy management studies were initiated by Inco's Utilities Department in late 1972, and resulted initially in a program of electric power cost reduction. This program produced significant results by improving the use of the water available for our hydraulic generation facilities and by a comprehensive peak reduction program. Our experience showed that a program of peak power control creates an awareness of both peak and energy costs, and thereby encourages a general reduction in the electric energy consumption as well as lowering the peak demand. Energy management is a continuing program at Inco and, recently, a formal energy management policy and program was instituted. Energy management committees were formed in each plant or mine area to identify the major areas for energy; consumption, thereby isolating areas with large potential energy losses, and determining immediate action which will improve the energy efficiency or reduce the energy waste within their respective areas. A decentralized program with good cross-communication between all committees was felt to be the best method of providing an on-going effective energy management program. In the future, the projections of dwindling fossil-fuel supplies in Canada and the resultant spiralling energy costs will further emphasize the need of sound energy management practices for all Canadian industry.

Jan 1, 1977

By G Chitombo, D Francis, P C. Stewart, I Brunton

The ability to precondition (weaken) a rock mass to enhance caving (cavability and fragmentation) is becoming increasingly important, as more potential caving deposits are in stronger rock masses, and at greater depth. This paper discusses a full-scale blast preconditioning experiment conducted at the Cadia East mining operation, including quantification of visible and microscale blast damage. From a cave mining perspective, the objectives of the experiment were to quantify the effect of confined blasting on rock mass characteristics relevant to enhanced caving, and to provide calibration data for the purpose of numerically modelling alternative blast preconditioning designs.The experiment was located approximately 360 m below surface, and consisted of two f165 mm blastholes (60 m vertical holes) and eight HQ diamond drill monitoring holes (35 m horizontal holes). The diamond drill holes were used to sample the rock mass before and after the blast at varying distances from the blastholes. Rock mass blast damage was quantified both visually using core logging, and on a microscale using LABYRINTH® statistical analysis of X-ray microtomography data. Results from the experiment indicated four major findings:on the visible scale, the experiment indicated a 147 per cent increase in the number of hairline cracks within 5 m (p value = 0.015), but no change in geotechnical logging parametersmicroscale tomography of intact rock samples indicate significant localised intact rock damage up to 4 m from the blasthole (p = 0.007)preliminary point load test results indicate that blast damage results in a significant reduction in intact rock strength (p = 0.050)the significant increase in porosity and microfracture size associated with damage provides a mechanism for reduced intact rock strength due to confined blasting.CITATION:Stewart, P C, Brunton, I, Francis, D and Chitombo, G, 2016. Quantification of rock mass damage associated with a confined blast preconditioning experiment at the Cadia East block cave, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 119–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Jérôme Girard, Shiu Kam, Sue Longo

"Historically, tailings management in a northern climate has involved the deposition of tailings into the Tailings Management Area (TMA) as conventional slurry. This type of system is obviously viable but presents challenges that are difficult to manage as circumstances change over the life of mine. These issues can include:? Increases in mill throughput, and? Life of the TMA for the life of mine.This case study will present how thickened, high-density, non-segregating tailings are used as an alternative to conventional slurry disposal to achieve greater storage capacity and enhanced environmental performance for a gold tailings facility in a northern climate. This paper will focus on how this change in deposition strategy accommodated the increased throughput of the mill and the increased life of mine. Specifically, the paper will discuss the addition and integration of new processes to the exiting mill system to accommodate the tailings management issues. It will highlight the challenges from laboratory testing to pre-feasibility to the engineered design of the thickened tailings system implemented at Musselwhite Mine.BACKGROUNDGoldcorp Canada’s Musselwhite Mine, in Northwestern Ontario (120 km north of Pickle Lake), is an underground gold mining operation that began production in 1997. The current mill throughput is about 4000 tpd (1.4 Mtpa). Gold extraction is based on a CIP process with cyanide destruction.The existing tailings management area (TMA) is located about 2 km southwest of the mill complex. The TMA is contained by high ground to the north and to the west and flanged by a moraine ridge along the south side. A number of dams have been constructed along this ridge. The dams were first built in 1996 and subsequently raised in 2000 and again in 2005. Excess tailings pond water is discharged to a polishing pond then released to the environment via a wetland.The TMA was originally designed to contain 13.7 Mt of tailings under a ponded surface for closure. The water cover was to inhibit adverse long-term environmental effects because the tailings contain pyrrhotite and other sulphide-bearing minerals that are potentially acid generating. The design was modified during Stage 3 Construction in 2005 to expand the storage capacity to 17.3 Mt (Golder, 2005). As of end of 2009, over 16 Mt of tailings had been deposited in the TMA. The slurried tailings were historically deposited at 50% solids."

Jan 1, 2011

By Thomas M. Barczak

With the development of the shield support, the primary requirement for successful ground control in longwall mining is to provide stable gate road and bleeder entries. Wood cribbing has been the dominant form of secondary support. However, the cost and limited availability of timber, along with the poor performance of softwood crib supports, has forced western U.S. mines to explore the utilization of other support systems. The recent success of cable bolts has engendered much interest from western operators. Several innovative freestanding support systems have been developed recently including: (1) "The Can"' support by Burrell Mining Products International, Inc., (2) Hercules and Link-N-Lock wood cribs and Propsetter by Strata Products (USA) Inc., (3) Variable Yielding Crib and Power Crib supports by Mountainland Support Systems, (4) the Confined Core Crib developed by Southern Utah Fuels Corporation; and (5) the MEGA prop by MBK Hydraulik. This paper assesses design considerations and compares the performance and application of these alternative secondary support systems.

Jan 1, 1996

By M Gerards, M Steinberg, T Graham

The quality and quantity of Australia’s secondary deposits, which include tailings streams and tailings dams, are higher than most countries’ primary deposits. In addition, these secondary deposits have already been mined and processed, meaning that the recovery of high-grade product requires low capital and operating costs.The most widely used process for the recovery of these valuable fine and ultra-fine hematite iron particles is the wet high-intensity magnetic separation technique, originally developed by Dr Jones over 55 years ago. Many of the original machines are still working today.The aim of this paper is to demonstrate the capabilities in terms of grade and yield of using sophisticated magnetic separation modules. All results and figures are obtained from test work and design and engineering work with material from the Pilbara. In addition, consideration is given to dewatering of iron ore product and tailings.Two types of tailings have been identified for processing. Firstly, tailings that have already been deposited in a tailings storage facility, and secondly, live tailings streams from an existing wet iron ore beneficiation plant. In both cases, the technical and practical results are shown along with relevant flow sheets and plant layouts. Finally, this paper highlights the total predicted power and water consumption, capital requirements and projected operating expenses.The results show that the operating costs are significantly lower than the mining and processing operations that are required for an equivalent amount of iron ore. The recovery of iron depends on various factors but is within the 30–50 per cent range at an equivalent grade to the mainstream product. Another significant benefit is that the magnetic separation process is water positive, meaning that water is released rather than added in the process.The processing of the Pilbara’s secondary deposits will therefore result in an overall reduction in operating costs, an increase in product yield from a plant, extend the life-of-mine and offer environmental benefits by reducing the tailings footprint and water usage.The quality and quantity of Australia’s secondary iron ore deposits and tailings are such that many other countries would judge these as equivalent to primary deposits. Furthermore, these tailings are already mined, available and liberated to such an extent that the recovery of a valuable product is highly economical in terms of capital expenses and operating expenses.CITATION:Steinberg, M, Graham, T and Gerards, M, 2015. Recovery of iron ore fines and ultrafines from tailings by using wet high-intensity magnetic separation – JONES WHIMS, in Proceedings Iron Ore 2015, pp 191–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By J. H. Cloete, S. M. Bradshaw, D. K. Chibwe

"Modern tundishes have evolved as vessels to serve as the final step in refining of molten steel by removing inclusions and promoting thermochemical homogeneity.In this study the flow behaviour in a four-strand tundish was investigated by means of a ½-scale water model as well as numerical modelling. The numerical and physical models were used to characterize residence time distribution and calculate properties pertaining to tundish flow regime. Three different tundish configurations were investigated: a bare tundish with no flow control devices, a tundish with a turbulence inhibitor, and a tundish with both a turbulence inhibitor and a dam.The physical and numerical models showed that a tundish without flow control devices is prone to significant short-circuiting. A tundish with a turbulence inhibitor was shown to be successful in preventing shortcircuiting and provided surface-directed flow that might assist the removal of inclusions from the melt. However, it was also observed that the upward-directed flow caused the maximum turbulence kinetic energy near the surface to increase dramatically. The potential for slag entrainment should therefore be considered during the design and operation of tundishes with turbulence inhibitors."

Jan 1, 2015

In spite of a global economy that continues to seesaw and a U.S. Congress that is at odds with the president and themselves, cities around the world are still spending billions on their infrastructure. And that bodes well for the underground construction and tunneling industry and the professionals who work in it. In June, 1,405 of those professionals gathered in San Francisco, CA for the Rapid Excavation and Tunneling Conference (RETC). In addition to the first rate technical programming, attendees were able to see first-hand the latest in tunneling technology from 127 exhibitors who occupied 152 booths. Two short courses preceded the conference and two field trips were offered following the conference.

Jan 1, 2011

By Ralph Johnson, Philippe Gaultier, Loui Fauteux, Andrew Dasys

"This paper outlines the implementation of the Mechanic's Stethoscope from the earliest stages of development to the implementation at Brunswick Mining and Smelting. It details the cooperative efforts of personnel at Noranda Technology Centre (NTC) and Brunswick Mining & Smelting (BMS) during the technology transfer of the Mechanic's Stethoscope. It demonstrates how everyone worked toward a goal of developing a product that is accepted as a useful addition to the work environment.The Mechanic's Stethoscope is an underground vehicle diagnostic system consisting of computer hardware and software intended to assist mechanics in daily tasks. Its tools facilitate quick and easy access to any information required during the maintenance of an underground vehicle. Each tool presents vehicle condition data in a simplified manner. The additional information improves the mechanics understanding of the vehicle condition. The result is a healthier fleet of vehicles and faster diagnosis times.When introducing a computer based system into a traditionally non-computer oriented environment a concern is the acceptance of the system. This concern exists on many levels."

Jan 1, 1995

By William S. Heckman

a. When to use: high surcharges, vertical capacity required, limit noise and eliminate vibrations, low headroom, eliminate vibration induced settlements. b. Advantages: eliminates impact noise and vibrations, high section modulus if required, vertical load bearing capacity; corrosion resistant, easy to apply facing for use as a permanent wall, adapts to complex wall layouts, would allow top- down construction, very high uplift resistance. c. Disadvantages: spoil disposal, not water tight, cannot penetrate rock and most obstructions, soil can erode between the piles if surface water and ground water are not controlled, hard to install reinforcing beams over 409 long; subject to high negative skin friction loads, high grout takes in rubble and organic soils. e. Relative cost to other systems: 30% to 50% more expensive than driven soldier piles and lagging except when surcharge loads are involved, or the pile cannot be driven due to noise and vibrations. About the same cost as a sheet pile system. Very competitive if high vertical load must be supported by the wall.

Jan 1, 1997

By NA UMC

Abstract Booklet

Dec 1, 2022

By H. William Zeller

The U.S. Bureau of Mines evaluated the effects of two iron-based fuel additives on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of engines used in underground mines. One additive, ferrous picrate, did not measurably affect exhaust emissions. This report is mainly about a ferrocene-based additive that reduced DPM between 4 and 45 pet., depending on engine operating conditions. The report concludes that the DPM reductions were caused by the catalytic oxidation properties of a ferric oxide coating that developed inside the engine's combustion chamber. The ferric oxide coating also decreased gas-phase hydrocarbons and O2, but it increased CO2 and NOx, The increase in NOx, of about 12 pet, is considered the only adverse effect of the ferrocene-based fuel additive. The results suggest that the effectiveness of ferrocene was partially offset by increased sulfates because of the high-sulfur fuel used. Recommendations for continuing fuel additive research are presented.

Jan 1, 2010

By R. S. Dean

Boron compounds have been considered for many years as possible additions to iron and steel. A very recent use of boron-steel rods was for the control of neutron intensity in the graphite-uranium pile at the Clinton plutonium plant(130).4/ Norris(129) reports that slags containing boric oxide reduce the ferrous oxide content of steels and thereby the aluminum required for deoxidation. Boron is not considered an alloying element, but minute amounts produce what is often called a "needled" steel. The study of a series of iron-boron alloys by convenient steps, starting with iron containing no boron, indicated that boron was a hardening agent and made the iron very difficult if not impossible to forge. Then came the discovery that very minute traces of boron are quite different from the smallest amount previously thought worthy of study.

Jan 1, 1946

By Munro P. D

Eh-pH measurements were taken on an industrial zinc reverse flotation process at Brunswick Mining and Smelting Corporation Limited. Laboratory zinc reverse flotation testwork on samples of the feed to the industrial process produced Eh-pH data which were similar to the data from the industrial process.Later, the Eh-pH data from the industrial process were compared with data from a pilot plant scale zinc reverse flotation process at Mount Isa Mines Limited. After comparison with the data from Brunswick Mining and Smelting Corporation, deficiencies in the pilot plant Eh-pH data could be recognised and corrective actions were taken for the pilot plant. A robust pilot plant zinc reverse flotation process was obtained with consistent performance at the expected level.The implications of these findings for a range of processes are also discussed.

Jan 1, 1988

By L. Evrard, S. Brouwer, E. Bosly, E. Boydens

"A partial desulfurization roasting process has been tested on a typical copper-zinc sulfide concentrate in a Nichols Herreshoff monohearth pilot furnace whereby the su!fµr is partially removed and iron is to a certain degree preferentially oxidized. The phase changes that occur in the particles during selective roasting at 650°C and 800°C over a range of residence times were investigated by the use of chemical analysis, optical microscopy, X-ray diffraction and electron microprobe analyses. The purpose of this work was to get an insight into the mineral assemblages formed by controlled oxidation roasting and to evaluate if this non traditional approach could be afterwards used to recover zinc, copper and iron by a physical separation method. IntroductionThere has been considerable interest over the years in improving extraction and processing procedures for recovering non ferrous metals especially from polymetallic ores containing copper, lead, zinc and iron sulfides with very fine intergrown phases. Complex sulfide ores, which represent considerable reserves and resources in copper, lead and zinc, as well as precious metals and sulfur, are difficult to treat by conventional physical processes, leading to impure concentrates at low metal recovery. Some methods that can be used to treat such ores were described by G. Barbery (1). Various metallurgical routes generally combining pyro- and hydrometallurgical methods have been explored to develop new processes to recover the metals from zinc-bearing sulfidic ores and concentrates (2, 3, 4). The feasibility of partitioning complex sulfide minerals to simpler phases in order to improve selective extraction of mineral constituents has also been investigated (5)."

Jan 1, 1999

By S. Z. Pethö

Pillar extraction at shallow depths with small pillars that were not originally intended for secondary extraction can provide a huge benefit to the coal mining industry in those areas where a significant percentage of the remaining coal reserves are locked up in small pillars at shallow depths and where opencast mining methods are simply not as cost-effective and practical to implement. A system considering all of the pertinent geotechnical and mining aspects for the safe and efficient pillar extraction of small pillars at shallow depths at Xstrata Coal South Africa (XCSA) has been further developed and implemented as part of an ongoing improvement process addressing all of the relevant legal and associated risk aspects. This work follows on from the previous pillar extraction work carried out at the ATC, Boschmans, and Spitzkop Collieries. The process involved a number of in-house workshops and sessions arranged with all key personnel from Tavistock Colliery, and also included Professor Nielen van der Merwe of the University of the Witwatersrand, a world renowned authority on pillar extraction, towards reviewing and developing the Modified NEVID pillar extraction system employed previously at Boschmans Colliery. The system is currently being employed at Tavistock Colliery with success and no major accidents, with around 655 000 t of coal having been successfully extracted from the pillar extraction panels.

Jan 1, 2012

By W P. Breytenbach

"The phased application of statistical process control (SPC) infers that processes are classifiable as pre-SPC (or phase zero), phase I and phase II processes, with different objectives being pursued in the different phases. Phase zero processes, defined as processes affected by assignable causes of variation, are characterised as follows: out-of-control with unknown autocorrelation structure having an unknown statistical distribution not performing consistently on target with minimum variability potentially incapable of conforming to the product specifications. The objectives of phase I SPC is to obtain estimates of the mean (µ), variance (s2), probability density function (f(X)) and the autocorrelation structure, as well as transforming the process into a phase II process (defined as a process conforming to specifications and performing on target with minimum variability). As in any other type of research or pragmatic improvement intervention, sampling is required is to achieve these objectives. The challenge of deciding a phase I sampling plan is multifarious since it has to cope with the aforementioned effects of assignable causes and provide for rigour estimates of the unknown parameters. Furthermore, deciding sampling plans in phase I invariably presents a classical catch-22 situation: appropriate sampling is required to determine the autocorrelation structure of a variable, but knowledge of the autocorrelation structure is required to formulate an appropriate sampling plan. This paper suggests, for random variables, guidelines to formulate sampling plans, and presents a methodology to estimate the inherent process parameters of process variables and an approach to identify assignable causes in phase I. CITATION:Breytenbach, W P, 2014. Rational sampling and standard deviations for random variables in phase i application of statistical process control, in Proceedings Sampling 2014, pp 141–154 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 29, 2014

By Varadarajan Seshadri

Geometallurgical characterization of iron ore which is a raw material for Iron making as in the case of charcoal blast furnaces operating in Brazil or for production of agglomerates such as iron ore sinter which serves as burden material for blast furnces of high productivity or pellets extensively used in the direct reduction processes all over the world in the iron and steel industry. Selection of proper raw material after due characterization should lead to an improvement of the productivity of the respective processes The usual classification of quality of iron ore is uniquely based on chemical analysis, granulometric and physical parameters. However not much emphasis has been given to the structural characteristics which also are important in the processes. Different typological categories of Brazilian iron ores have been used in the characterization . For instance, several kinds of hematite crystals like specularite, martite and microgranular hematite, etc with variable crystal sizes are found in the different ore types. They are also composed of different of fabrics and types of accessorial mineralogical constituents and have different porosities, pore diameters, etc which influence the cold and the hot agglomeration stages of the ore fines, and also chracteristics such as reducibility, decrepitation etc, important for assessment of quality of iron ores. . The first step for attaining a good characterization of ores is to know in detail about the structure of the deposit, shape of the body, types of iron ores and their distribution. This requires a geological-structural study and the mapping of the bodies using mineralogical criteria for typological classification of ores. followed by structural characterization of materials in stages of mining, comminution, screening and concentration processes. In this contribution a geometallurgical approach for quality control of Brazilian iron ores for sintering and pelletizing processes is highligted.

Jan 1, 2006

By Loughnan FC

There are some thirteen laboratories in Australia in which coal petrological work is carried out on a consistent and routine basis. Applied coal petrological research is conducted by several institutions in different disciplines which can be grouped into four main categories:

Jan 1, 1989

By K. N. Santini, J. M. Barker

The perlite industry in the United States continued to undergo rapid change and increased competition last year as it did in 2002. U.S. production in 2004 was 510 kt (562,000 st),an increase following five consecutive years of decline (Table 1). Perlite is exported to Canada and to the Pacific Rim. These partially offset imports. Perlite imports from Greece to the eastern and Gulf Coasts of the United States declined by about 22 percent after reaching a record 240 kt (264,000 st) in 2003.But their market remains protected by high rail rates from western U.S. plants. Minor imports of perlite persist by Termolita from Mexico.

Jan 1, 2005

By Z Tong, M Gao, X Wang

In response to the need for improved magnetic separators for beneficiation of fine grained iron ores that have been finely ground to liberate the iron minerals from the gangue, a series of high efficiency wet drum permanent magnetic separators (T-GCT) has been developed by Maanshan Tiangong Technology Co Ltd. These magnetic separators have high efficiency for separating superfine strongly magnetic minerals and the ability to produce high-grade concentrates with high recovery. They are ideal replacements for conventional drum magnetic separators, especially for treating superfine particles.

Jan 1, 2009