Search Documents

By Kimio Itagaki, Torn Matsumoto, Makoto Ohtsuka, Kentarou Harada

"The structure and hydrogen-absorption properties of LaNis thin films were investigated in the present study. LaNis thin films were prepared by a sputtering method with a radio-frequency power, Ws, of 50 -400 Wat substrate temperature, Ts, of323 -573 K. Nickel content of the films decreased with increasing Ws, however, there was no dependence on Ts. At low Ws and low Ts, amorphous films were deposited. In other conditions, the films were polycrystalline. The films prepared at high Ws and low Ts, or at low Ws and high Ts, exhibited only a (h k · 0) peak in the X-ray diffraction profiles. This indicates that the c-axis of crystalline films was oriented parallel to the substrate plane. At high Ws and high Ts, the films with columnar structure were obtained. Hydrogen-absorption capacity of the thin films increased with increasing Ws. The pressure plateau did not appear on the pressure-composition isotherms. The films deposited at high Ts represented a higher equilibrium pressure.IntroductionThin films of hydrogen storage alloys can be applied for an electrode of rechargeable battery or fuel cell, a filter for H1 purification and various kind of sensor. Some studies on the preparation of the thin films of LaNi5 intermetallic compound, which is a typical hydrogen storage material, have been done hitherto. Adachi et al. , 2) and Sakaguchi et al. 3) prepared amorphous and crystalline LaNi5 thin films using flash evaporation of alloy powders and measured the pressure-composition isotherm for the prepared film utilizing a quartz crystal mass monitoring (QC:MM) method. It was found that the prepared amorphous film absorbed hydrogen without disintegrating into the powders and the hydrogen-absorption capacity of the films increased with the degree of crystallinity. Sakai et al. 4) reported that the maximum hydrogen storage capacities of amorphous and crystalline LaNi5 thin films, fabricated by a RF sputtering method using combination targets, were about 40 mA h g-1 (LaNisHo.7) and 160 mA h g-1 (LaNi5H2.6), respectively. Uchida et al. 5, 6) prepared LaNi5 thin films using flash evaporation of alloy powders and measured volumetrically the pressure-composition isotherm for the prepared film. It was reported that the hydrogen-absorption capacity of the films changed by the annealing treatment."

Jan 1, 1998

By J. Méndez-Nonell

The thermodynamic and chemical properties of SrSO4 and SrS in a gaseous flow of CO and CO2 at high temperature are discussed. The thermodynamic analysis of the system was made using data from the literature. The results obtained from the thermodynamic analysis were experimentally verified using the thermogravimetric technique. The experimental results suggest the formation of a complex compound between SrO and SrSO4. It was also found a change in the chemical mechanism of the process between SrSO4 and CO-CO2 and in the chemical mechanism of the process between SrS and pure CO2.

Jan 1, 1995

By P. E. Nolan

The disproportionation of carbon monoxide is an important aspect of reduction processes, in the production of carbon filaments for composites, and in the removal of CO from CO,. It can also be a hindrance, causing carbon fouling of equipment and metal dusting. The reaction is thermodynamically favored at lower temperatures, but it occurs slowly. Catalysis of the reaction by transition metals has been examined. A materials science approach to the selection of a catalyst material and of optimum operating conditions is being taken in the present work. Of particular interest is characterization of a catalyst that can be repeatedly regenerated to prevent deactivation in long term use. Experimental data on a less studied catalyst, ruthenium, are reported.

Jan 1, 1992

By Du Sichen, S. Seetharaman, J. A. Bustnes

"The present study deals with the kinetic studies of reduction of some selected transition metal tungstates with hydrogen. The measurements were carried out by the isothermal thermogravimetric method. Shallow powder beds were employed in order to avoid the effects due to transport phenomena affecting the reaction rate. In this way, the chemical reaction rates could be selectively studied. The experiments were carried out in the temperature range 873 - 1173 K. From the experimental data, the activation energies were evaluated and were found to be around 88 kJ / mol in the case of both iron as well as cobalt tungstates indicating the similarities in W-O bonds in both cases. The activation energies obtained are discussed in the light of the position of the transition metal in the periodic table as well as the thermodynamic stabilities of the various tungstates.IntroductionThe tungsten containing hard metals, characterized by high density, belong to a class of two-phase metal matrix composites. While these types of materials have traditionally found their applications within the defence industry as armour-piercing projectiles, counterbalance in helicopters and military aircrafts, outer casings of hand-grenades, etc., commercial applications for this class of alloys also exist, including radiation shields, penetrators for the oil industry, turbines for turbo-jet engines and a wide range of sports related parts. A possible route to the production of these alloys is to reduce the tungstates such as FeW04, Co W04 and NiW04 using a reductant like hydrogen or carbon monoxide. In order to have a better understanding of the processes involved in the production, it is important to have a knowledge of the reduction kinetics for these tungstates. According to the knowledge of the present authors, while the reduction ofNiW04 by hydrogen gas has been investigated earlier in the present laboratorypl no systematic reduction study has been carried out previously for the tungstates of iron, cobalt."

Jan 1, 1996

By H. Shang

The materials science and metallurgical engineering communities have expended enonnous resources in developing high fidelity process models. Exploiting these Models for Predictive Optimization (MPO) and Control (MPC) is a new frontier in Materials Process Engineering that will lead to exceptional process perfonnance. This paper will begin with a short survey of the development of high quality process models available in the literature and a discussion of how these could be used to improve process operation. A summary of the current "state-of-the-art" in process automation technologies and the traditional framework in which these technologies are deployed will be presented. An illustration of the use of MPO in process design and operations will be presented for the continuous casting of steel. In addition, a simple run-out table simulation will be used to demonstrate the power of the MPC technique.

Jan 1, 2003

By G. Van Weert, A. van Sandwijk, O. W. J. S. Rutten

"Cathodic and anodic reactions in an acidic nitrate medium were studied in reference to the production of electrolytic manganese dioxide from pyrolusite' (Mn02) ores by reductive leaching. Two USA ores were investigated. The reductant for the pyrolusite ore is produced cathodically in an electrolytic cell and can either be nitrous acid (HN02) or nitric oxide gas (NO). In this work emphasis was placed on the nitrous acid leach. In a high-temperature leach in a nitrous/nitric acid medium, manganese and silver are solubilized and iron is not. Anodic electrowinning of manganese dioxide from the acidic manganese nitrate electrolyte yields flaky y-Mn02, similar to that produced from sulfate and chloride electrolytes. Cathodic regeneration of nitrorts acid was studied in a membrane cell in 1.0 M nitric acid and 0.0 to 0.1 M nitrous acid on a' platinized titanium cathode. At cathode potentials ranging from +950 to +700 mV (SHE), cathodic reduction to nitrous acid takes place, at cathode potentials < +700 mV, cathodic reduction of nitrous acid to nitric oxide takes place. A conceptual process is presented and discussed.IntroductionManganiferous-silver oresLarge reserves of manganiferous-silver ores are present in the Southwestern United States and Latin America. These ores are generally refractory to hydrometallurgical methods of treatment, due to the insolubility of the higher oxides of manganese (Mn 4+) in all common lixiviants such as cyanide solutions, dilute sulfuric acid, nitric acid, ammonia, salt solution, thiosulfates, etc. The silver is either bound by the insoluble manganese, or is rendered inaccessible to cyanide leach solution by the surrounding manganese mineralization.Higher oxides of manganese will dissolve if they are first reduced pyrometallurgically to manganous oxide (Mn2+). This is a widely used pretreatment for manganese dioxide ores and subsequent dissolution in sulfuric acid is common. In order to avoid the pyrometallurgical pretreatment with its large energy requirements and gaseous emissions, fully hydrometallurgical processes have been proposed. These processes are based on the presence of a reductant in solution, in order to reduce the insoluble higher oxides of manganese to soluble lower oxides. Aqueous S02 has been proposed and tested on industrial scale by the U.S. Bureau of Mines. After washing, silver could be extracted by cyanidation. The neutralization of the pulp prior to cyanidation however causes problems in filtration and the reagent consumptions are high [1]. More recently, acidified thiourea and bacteria were proposed for the solubilization of both manganese and silver in a single leach step. High extractions were obtained, but drawbacks of these methods are high reagent consumption or slow kinetics [2,3]. For the options of manganese recovery from the leach filtrate, precipitation with persulfate or ammonium carbonate and ion exchange have been proposed. The proposed options for silver reclaim are precipitation with either zinc or Na2S and adsorption onto activated carbon."

Jan 1, 1997

By Hongyang Cao

The iron constituents selectively separated from the modified copper slags by magnetic separation and flotation.were studied. The results of magnetic separation for modified copper smelting slags show that the grinding size, current intensity and dispersant agent had great influence on grade, and recovery ratio of TFe in preparation concentrate; The results of flotation for magnetic concentrate show that the positive flotation of sodium oleate negatively upgrade the grade of magnetic concentrate, but the reverse flotation of lauryl amine and soluble starch are effective. The grade of TFe can reach 54% and the recovery ratio can reach about 90% in magnetic concentrate, when the grinding size is 45.8µm and the current intensity is 2.5A. The optimal effect is obtained by using lauryl amine as collector and soluble starch as depressant to reverse flotate magnetic concentrate, and the grade of TFe is upgraded 2.37%.

Jan 1, 2009

By I. C. Howard, E. J. Palmiere

"Heat transfer and friction in hot flat rolling have traditionally been characterised by an average heat transfer coefficient (h) and an average friction coefficient (p.). However, the presence of oxide scales and asperities at the interface question the use of such averages. The apparent irregularity and lack of pattern of interactions at the interface has prompted this present investigation to move away from averaged h and 11 values, and to study their local evolution based on probabilistic rules. The approach is based on the probability of finding the workpiece surface in a specific configuration at a particular instance of time in the roll gap. These rules are based on observations of surface phenomena such as scale behaviour during hot rolling. The model is implemented using user-subroutines integrated with the commercially available finite element program ABAQUS™. The results show the strong dependence of h and u on the local scale interactions. In particular, the effect of scale thickness, material behaviour and processing conditions on the evolution of hand 11 are discussed. Finally, the development of a Cellular Automata based Finite Element (CAFE) model is proposed to model the combined interfacial phenomenon of friction and heat transfer at the tool-work piece interface.IntroductionIntricate interactions between process variables in hot rolling of steels make it a challenge to the modelling community. For a given material and geometry combination, reducing interfacial power losses can increase the efficiency of the rolling process. The roll-strip interface, therefore, forms the critical zone and is currently the domain of intense investigation, especially to characterize interfacial frictionl • 2 and heat transfer3 • 4 . These interfacial phenomena are inter-related and cannot be studied in isolation. However, very few mathematical models4 • 5 combine an analysis of friction and heat transfer and deformation of the strip-roll interface taking into account the role of asperities and oxide scales."

Jan 1, 2001

By V. P. Keran

The lead and copper smelting processes employed by Mount Isa Mines Limited, Mount Isa, Australia, are used to illustrate an operating viewpoint of some problems and solutions encountered in existing commercial sulphide smelters. The smelting processes discussed; include updraught sintering, blast furnace and reverberatory smelting, and converting. Selected examples are given of methods implemented, and options available, to improve the productivity and efficiency of conventional smelting processes.

Jan 1, 1983

By Jun Lu, Min Chen, Wei-jian Su, Jian-zhong Luo, Yu-tao Lei

"In the case of treating phosphatizing wastewater containing zinc, zinc had an impact on the solution chemistry, especially on pH. Fe2(SO4)3 and CaCl2 were used as precipitators to remove phosphate from zincic phosphatizing wastewater and the optimum pH was investigated. Zinc ion had a significant effect on the optimum pH. The optimum pH ranges were 12.10(inlet concentration of 15.67mg/L, outlet concentration of 9.53mg/L), 3.04-5.50(inlet concentration of 11.97mg/L, outlet concentration of 0.44-0.26mg/L), and more than 10.72(inlet concentration of 12.24mg/L, outlet concentration of less than 0.47mg/L) under the conditions without precipitator, with Fe2(SO4)3 and with CaCl2 respectively.Introduction Phosphate coating is commonly used for protective coating of machine elements. Including oil removal by caustic washing, rust removal by acid washing, phosphatization and inactivation, the phosphatization process produces wastewater containing inorganic salt of high concentration, especially the phosphate, beyond the environmental standards and polluting environment seriously. What’s more, the wastewater from zincic phosphatizing technology also contains another pollutant, zinc. At present, Chemical Precipitation (CP) and Biological Nutrient Removal (BNR) are two of most common technologies of phosphate removal. BNR, such as A/O, A2/O and UCT technology, is suited for wastewater containing organ phosphorus of low concentration and CP for wastewater with phosphate of high concentration [1]. Researches on CP treating wastewater containing phosphate of high concentration, mainly focus on adding quantity of precipitators[2-5] and coagulants[2-4] and the choice of technologies[3-9]."

Jan 1, 2008

By Jilai Xue

Experiments with various industrial cathodes ranging from 35 wt.% to 100 wt.% graphitic and fully graphitized carbons were carried out in a laboratory aluminum electrolysis cell. Sodium and cryolite bath penetration into the cathode samples was measured by XRD and SEM-EDS analysis. For a higher cryolite ratio in the bath, the cathodes with lower graphitic carbons exhibited more sodium penetration than the fully graphitized. The increased graphitization in the cathode materials can reduce Na, NaF and Na3AlF6 penetration. SEM-EDS inspection reveals that the sodium and fluorides penetration within the cathode samples has different patterns for varying graphitization of the carbon materials. XRD quantitative analysis indicates that there is a large percentage of Na3AlF6 in the penetrated bath. The results can provide useful information for quality evaluation of the industrial cathode products.

Jan 1, 2010

By Sergio N. Monteiro

Wastes generated by our society and the question on how to dispose them is, nowadays, a relevant matter of concern. The objective of the present work was to characterize the technical properties of composites made of discarded jute sackcloth with its coarse wove fabric, serving as reinforcement phase, and polyethylene wastes collected from city dumps, as continuous matrix. Different amounts, up to 30 wt.% of jute plain weave, fabric were press molded at 160°Ctogether with sieved polyethylene particles. The resulting composites displayed mechanical properties that could compete with those of low-density wooden board. Both by presenting a solution to, otherwise, disposed wastes and by helping to prevent deforestation, the investigated composite may be regarded as an environmentally correct material.

Jan 1, 2006

By D. D. Harbuck

The U.S. Bureau of Mines recently identified a significant new source of scandium in an Oklahoma tantalum waste residue (approximately 0.24 pct Sc). Because scandium is a strategic and critical metal which the Department of Defense has classified for special consideration, the Bureau is researching methods of recovering scandium and associated metals from this and other process residues. A variety of operating parameters were evaluated to determine the best technique for recovering scandium. Testing showed that by sulfating the residue at temperatures as low as 150&apos; C for reaction times as short as 0.5 hr, over 94 pct of the scandium converted to a water soluble form. Solvent extraction using DEHPA selectively recovered 100 pct of the scandium from the water leach solution.

Jan 1, 1992

By L. A. Neumeier

The Bureau of Mines, U.S. Department of the Interior, is investigating the feasibility of partitioning complex sulfide minerals to simpler sulfide .phases by sulfldation reactions. Such partitioning can afford opportunity to improve selective extraction of mineral constituents of value. This report describes initial research involving sulfidation partitioning of chalcopyrite concentrates. Small chalcopyrite samples were sulfidized with elemental sulfur in glass capsules sealed after evacuating and backfilling with helium, by heating for 1 to 24 h at specific temperatures in the range of 250° to 500° C. which extends from below to above the boiling point of sulfur (-445° C). Above the boiling point of sulfur, the overall reaction with adequate sulfur (13.9 wt pct of CuFeS2) is 5CuFeS2 + 4S g ? Cu5FeS6 + 4FeS2.

Jan 1, 1989

By Donald J. Hallbom

Limonitic nickel laterites slurries exhibit complex rheological properties including time dependency that varies from thixotropy to rheopexy. Chronic problems may occur if plant designers and operators fail to take time dependency into account. Stress decay tests indicate that laterite slurry takes roughly two minutes to approach steady state after a step change in the shear rate. As a result, most rheometer measurements are taken at a non-equilibrium state, making evaluation difficult. Two minutes is also long relative to the time that a unit of slurry in a processing plant is at any given shear state, so the slurry may never reach equilibrium. This paper presents a method to describe the rheology of laterite slurry using a Flow Array, which describes the rheology using an array of instantaneous flow curves crossed by an equilibrium flow curve. A rate equation for structural change in non-equilibrium conditions allows time dependence to be efficiently modeled. This flow array allows the flow behavior of time- dependent slurry to be predicted in non-equilibrium conditions using a simple time-step methodology. Keywords: Rheology. nickel laterite, hydraulic transport, pressure acid leach, flow array

Jan 1, 2004

By P. N. Anyalebechi

The effects of Si (0.19-0.52 wI. %), Fe (0.20 wI. %-0.44 wI. %), and Cr (0-0.10 wI.%) on the response of ingots of aluminum alloy 3004 solidified at different rates (O.IO°C/s to 30°C/s), to homogenization heat treatment have been investigated. Response to homogenization was determined by quantifying the following microstructural parameters: (i) amount of Mn retained in solid solution; (ii) types, relative amounts, sizes, size distributions, shapes, and chemical compositions of second phases; (iii) extent of the alpha-transformation (i.e., AI6(Fe,Mn) --7 (XAI12( Fe,MnhSi) reaction; (iv) dispersoid formation; and (v) alleviation of dendritic microsegregation. Of the three alloying elements investigated, Si had the greatest effect on the response of aluminum alloy 3004 to heat treatment. Increase in Si content, fineness of cast microstructure, and homogenization temperature facilitated alpha-transformation reaction, dissolution of Mg2Si, loss of Mn supersaturation, and formation of AldFe,Mn)3Si and Mg2Si dispersoids.

Jan 1, 2008

By Jeremy Gregory

The disposal of end-of-life electronics is an issue receiving increasing scrutiny. This paper evaluates several alternatives for recycling cathode ray tubes (CRTs) within monitors and televisions. The primary recycling options for the glass, reuse in new CRTs or as a smelter flux, are examined from economic and environmental standpoints. The economics are modeled using a cost model that includes dependencies on processing costs, transportation logistics, and incoming material composition. The environmental consequences are modeled using life cycle assessment methodologies to determine the energy embodied in each processing alternative. Results map out preferred processing alternatives across a range of technological and operational conditions. The results indicate that economic costs and environmental consequences are heavily impacted by transportation. The preferred destination of CRT glass for a recycler is highly dependent on the proximity of the consumer to the recycler, although it is generally economically advantageous for the recycler to extensively dismantle the CRTs.

Jan 1, 2006

By P. A. Rusin

Many manganiferous silver deposits remain undeveloped because standard chemical extraction methods yield poor recoveries or are &apos; environmentally unacceptable. Biotreatment of such ore deposits in our laboratory resulted in manganese and silver recoveries of greater than 90%. Ore and sediment samples were collected from mining sites in Colorado and Arizona. Portions of samples were incubated in a semi-solid mineral salts medium amended with 20 mM glucose mid manganese dioxide (Mn medium). The cultures were incubated at 3(fC until manganese reduction was detected by a .color change fr:om .black to clear. Bacteria from these cultures were purified on Tryptic Soy Agar and individual isolates were retested for Mn reduction by an agar overlay method. Bacteria were identified according to Bergefs Manual ?of Systematic . Bacteriology. Most of the Mn-reducing bacteria are Bacillus species. Bacterial manganese reduction kinetic experiments were performed in 52 ml mineral salts broth supplemented with manganiferous silver ore instead of manganese dioiide. These cultures were incubated with agitation for 16 d. Aliquots were removed periodically and analyzed for solubilized manganese by atoniic absorption (AA). Cyanide (1,0 M) Vias added to the remaining ore-medium mixture for a 24 h bottle roll. The supernatant was analyzed for soluble silver by AA. Similar experiments were conducted on a larger scale using 15% pulp density. After bfotreatment of the ore, standard bottle rolls were performed. The pregnant solutions and the residues were analyzed for manganese and silver?using AA or fire assay as appropriate. In sterile. controls-which received no biotreatment, manganese and silver recoveries were 0.3% and 10% respectively; During biotreatment, total manganese solubilizatiori was as high as 99.8%. The reduced manganese could . be stripped from ?the growth medium using hydrometallurgical techniques. Silver recovery vaned from 70% to 92.5%. Microbial treatment of refractory mangairlferous ores can result in high recoveries of manganese and silver. Retention time varies depending upon the relative concentrations of manganese, silver, and other metals in the ore with only two days required in some cases, The biotreatment of ore is environmentally&apos; acceptable while the use. of chemicals such as sulfur dioxide is less so.

Jan 1, 1991

By Jean P. Murray

The extractive metallurgical industry is a major consumer of high-temperature process heat. It is, consequently, a major contributor of C02 emissions and other greenhouse gases derived from the combustion of fossil fuels for heat and electricity generation, or from the process itself. These emissions can be substantially reduced by replacing fossil fuels with solar energy as the source of process heat. Concentrated solar radiation can supply a large amount of thermal energy to endothermic reactions at temperatures exceeding 2000 K. Another potential for C02 emission reduction exists as well. Thermodynamically, the total amount of energy required for metal production at any given temperature is the enthalpy change of the reaction, AH. Of this total, an amount equal to the Gibbs free energy AG must be supplied as high quality energy in the form of electrical work or by using a reducing agent. Many conventional metallurgical electrolytic processes and reducing furnaces are unable to add only the thermodynamically required electricaVchemical energy due to process inefficiencies. Electrical work in excess of AG for the reaction may be used to supply process heat, or excess chemical reducing agent burned to supply process heat. Besides the thermodynamic and economic drawback, this inefficiency results in excess C02 emissions derived from the combustion of fossil fuels. With these practices, energy becomes an important cost element of the metal produced. Highly-concentrated solar energy has the demonstrated potential to separate these two forms of process energies, allowing the addition of only the thermodynamically required high-quality energy while high-temperature solar process heat is provided to the reactor. Examples of metal oxide reduction processes that have been studied experimentally in solar furnaces include the production of Fe, Al, AI/Si alloy, Mg, Zn, Tic, Sic, CaC2, TIN, Si3N4, and AIN by carbothermic reduction of their oxides, and the high-temperature solar- electrothermal reduction of ZnO.

Jan 1, 1999

By Gary R. Adams

Coating thickness control is typically difficult with touch-up solders for galvanized steel, and corrosion properties and abrasion resistance are sometimes poor. This paper reports on progress in ILZRO-sponsored research to develop an improved touch-up solder. Encouraging results were achieved in torch soldering trials with zinc-tin based alloys. Mouldability and coating thickness control were achieved over a practical working temperature range in which the solders consisted of a viscous mixture of solid primary zinc phase particles in a liquid zinc-tin eutectic matrix The mouldability was dependent on the microstructure of the starting material, and optimum structures could be obtained through control of casting solidification rates and/or by the addition of small amounts of copper. Hardness and preliminary corrosion test results showed potentially good mechanical and corrosion behaviour. The absence of toxic materials ensures environmental friendliness. Comprehensive performance testing is continuing on selected experimental zinc-tin-copper touch-up solders.

Jan 1, 1992