Search Documents

By Ashwini Kumar

Flame impingement on the burden is routinely encountered during the initial phase of melting in aluminum reverberatory furnaces. This impingement causes an obstructed pathway for the hot gases, and hence the circulation and residence time of the hot gases are greatly impacted. Moreover, as the load melts, the flames gradually achieve an unobstructed path leading to reduced gas residence times. This flame impingement and constantly changing combustion space volume will lead to vastly different fuel and oxidizer mixing patterns and thus affect the overall furnace performance. Fine tuning the burner operating conditions such as flow rates and injection angles with the changing combustion space could result in significant improvements to the furnace efficiency. However, one has to gain a better understanding of the furnace dynamics to know the suitable parameters to adjust. Physical modeling can be elaborate and expensive to conduct on a regular basis while Computational Fluid Dynamics (CFD) can cost-effectively address this challenge. In this study, the furnace model is created with a particular loading pattern to understand the flame dynamics in the presence of a piled load. This configuration can be thought of as a computational model of the furnace with the burden at a particular stage of the melting process. Thermal efficiency and behavior of the furnace are quantified and the predicted values are compared with the operational data from an experimental reverberatory furnace.

Jan 1, 2008

By Kazuya Kitatani, Gen Sasaki, Naoto Ohta, Hideharu Fukunaga, Makoto Yoshida, Jin Pan, Kenya Nagahisa, Toshihiro Ishikawa

"A sintered SiC (Tyranno-SA) fiber-reinforced MAS glass matrix composite was fabricated by using a slurry infiltration method and hot-pressing. The microstructure and mechanical properties were investigated: To prepare the preform, the MAS glass slurry including a dispersing agent was infiltrated into a bundle of the fibers. The preform was then hot-pressed under the conditions of 1473 K, 30 MPa, 3.6 ksec. A unidirectionally-reinforced oxide matrix composite with 50% Vf. of the fiber and a density of 2.84 g/cm3 was obtained. As the mechanical properties at room temperature, the three-point flexural strength- and quasi-static adsorbed energy were 500 MPa arid 6,000 J/m2, respectively. Without graphite or an h-BN pre-coating on the surface of the fiber, pull-out and bridging of the fibers from the matrix was found, and this leads to a high value of the adsorbed energy. By TEM observation, nano-scale crystalline products were found between the fibers and the glass matrix. The push-out test reveals that this layer causes the appropriate debonding of the interface during the fracture process of the composite.Introduction It is known that the CFCCs (continuous-fiber-reinforced ceramic matrix composites) are characterized by their non-linear fracture behavior, which is' hardly found in monolithic ceramic materials. It is inevitable for the CFCCs to exhibit a large fracture toughness so 'that debonding of the fiber/matrix interface; pull-out and bridging of the fibers then' occurs during the fracture process. This series of fracture behavior is known as the so-called ""the mechanism of toughening of the CFCCs"". Thus, different from the MMCs in which strong interfacial bonding is necessary, the interfacial strength of the CFCCs has to be controlled. As techniques for controlling the interfacial strength, it is also known that both a CVD-graphite coating and an h-BN coating are effective to induce the mechanism of toughening[1,2]. In the case, of the Si-C-O or Si-Ti-C-O fibers/glass or crystalline oxide matrix composites, it is reported that the formation of the in-situ graphite layer, which is also effective to increase the fracture toughness of the CFCCs, is often found during the fabrication process such as hot-pressing. The lower the crystallinity of the Si-C-O fibers, the higher is the tendency to form the in-situ graphite layer as found by the chemical reaction between the fibers and the glass matrices[3-12]. On the-other hand crystallized stoichiometric 'SiC fibers are attractive for high temperature service because of the higher phase stability compared to the Si¬C-O or Si-Ti-C-O fibers. However, in the previous, studies, the mechanical properties and the interfacial chemical reaction of the crystallized SiC fibers / glass matrix Composites have still been unknown. In this study, a polycrystalline 'sintered SiC fiber-reinforced MAS glass composite was fabricated. The mechanical properties and microstructure were then investigated. The slurry infiltration technique followed by hot-pressing was used to prepare the composites. The formation of the in-situ graphite layer and the relationship between microstructure and mechanical properties at room temperature were examined by the TEM observation of the fiber/matrix interface."

Jan 1, 2000

By Nexhmedin Lohja

The production of high-carbon ferrochromium in a submerged electric furnace based on double-level technology has some advantages compared to close-type furnaces with one tap hole. These advantages include the reduction of the specific energy consumption for the overall process, good separation of ferrochromium from slag, an effective treatment of raw materials including lean chrome ores (low percentage of Cr2O3) etc. An outline of the operation of this furnace along with the production line of briquettes from fines of chrome ore by using organic and inorganic binders, will be followed by a description of the recent work carried out to improve the energy consumption in this furnace through a pre reduction process of Cr2O3 ores by the off-gas energy recuperated from the furnace and the use of SiC in the feed. A short theoretical analysis of the new work will also be given.

Jan 1, 2006

By R. G. Reddy

The oxidation kinetics of A13Ti intermetallics have been studied at the temperature range of 850°C to 100O0C in pure dry oxygen. The oxygen diffusion rates were investigated using TGA method. Parabolic rate constants were calculated. The oxidation scales were analyzed using SEM, EDS and X-ray diffraction. A continuous A120, scales with a little TiO2(rutile) were formed on the intermetallic surface. The A13Ti intermetallic exhibited excellent oxidation resistance among the Ti-Al base intermetallics.

Jan 1, 1997

By He Zhi-jun, Ning Zhe, Pang Qing-hai, Zhang Jun-hong, Zhan Wen-long

The effect of microwave irradiation on grinding property of coal was studied by using Hardgrove grindability index tester. Superior grindability of coal was obtained to varying extent after microwave irradiation treatment. The variation in microstructure of pulverized coal during microwave irradiation was observed by utilizing scanning electronic microscope (SEM). The results indicated that the different microwave absorbance of minerals and carbon matrix led to cracks on their interface, by which coal particles were further pulverized and therefore the granularity of coal powder was reduced. Due to the different formation process of various coals, bituminite and anthracite are very different in physical and chemical properties. According to the content of coal pulverization, it can found that microwave irradiation has a stronger pulverizing effect on bituminite in comparison to anthracite.

Jan 1, 2016

By L. N. Ertzeva

The present work is dedicated to investigation of the sulfidizing process of ore pyrrhotite concentrate with recovery of a sulfide material, enriched with non-ferrous metals, and waste pyrite, with downstream separation by a certain beneficiation method.

Jan 1, 2006

By D. N. Collins

A sampling program was conducted in which both spoon and isokinetic sampling techniques were used to collect samples from the reaction shaft. The samples were then characterised by chemical, XRD and mineralogical analysis. Further information was acquired by measuring the oxygen potential and temperature at the bottom of the shaft using disposable probes. Comparison of the results of the two sampling methods showed that the spoon samples were devoid of material less than 25 m. Sulfur analyses on the samples provided information on the extent of reaction, plume shape and recirculation patterns. Disposable probe measurements showed the measurable particle temperatures ranged from 1150 to 1700 °C and that the material falling into the bath had a normalised oxygen potential similar to the slag. These latter measurements combined with the sulphur elimination and mineralogical analyses provided further information on the extent of reaction and enabled the reaction sequence to be ascertained.

Jan 1, 1999

By James T. Staley

Quenching and aging are critical processing steps used to produce precipitation hardenable aluminum alloy products. This work describes personal computer programs that employ models to predict certain properties after quenching and aging and graphically display them. One of the programs allows the user to predict the attainable strength and toughness of aluminum alloy products after an arbitrary quench. Another program simulates the changes in strength and electrical conductivity occurring during second-step aging alloy 7050-T7X products as a function of thickness, furnace temperature set point, and furnace characteristics.

Jan 1, 1993

By I. C. Knight

The current levels of copper smelter by-product acid production are reviewed on a regional basis, together with the possible changes in the future. There will be increasing pressure for all smelters to achieve a sulphur capture level of at least 95% by the end of the decade.

Jan 1, 1996

By Guozhu Ye

"One of the most essential problems associated with the treatment of EAF dust is its high content of halogens. For most thermal processes for zinc recovery, such as the plasma processes with a zinc condenser, the halides in the gas stream will form a dross phase that results in a low zinc yield. For those with zinc oxide as main product, such as Waelz oxides, the high halogen content in the product implies a great degradation of the product quality and the product can only be sold at a low price. Further processing of zinc oxide with high halogen content either by pyrometallurgical or hydrometallurgical processes will also result in process problems.This paper will review the pre- and post-treatment alternatives for halogen removal based on the comprehensive characterization work that has been carried out at MEFOS and the preliminary experimental results.The experimental results show that chlorine and fluorine content could be reduced to 450 ppm and 50 ppm respectively by selective sulfation, and to about 200 ppm by soda leaching. Selective sulfation of zinc oxide in the EAF dust will also be discussed."

Jan 1, 2000

By G. Roderick Eggert

Material criticality reflects the degree to which a raw material is both necessary and subject to supply-chain risks. This study compares the criticality of selected raw materials from the differing perspectives of the manufacturing sectors of China, the European Union, Japan and the United States.

By Karen Tempel

Newmont's Lone Tree Mine is located 30, miles east of Winnemucca in Humboldt County, Nevada. Starting in February 1994 a pressure oxidation circuit was commissioned to treat refractory gold ores. Gold is leached and recovered from the oxidized slurry in a six-stage carbon-in-leach (CIL) circuit. Lone Tree has been able to maintain tighter control' of cyanide addition and reduce cyanide consumption its CIL circuit through the installation of Degussa's Cyplus® CCS Cyanide Control System in the spring of 2000. 'The Cyplus® CCS, along with additional inputs' from plant sensors, has allowed tor a more efficient and effective control strategy over the manual control method used ,in the past. This paper documents the key aspects of the Cyplus® CCS installation; the development of the control strategy, and the benefits achieved from enhanced control.

Jan 1, 1998

By P. R. Taylor

Diamond films have been successfully formed in an inductively coupled plasma (ICP) chemical vapor deposition (CVD) system from several gas mixtures: CH,-H,, C2112-112, and C2112-112-02' Our previous thermodynamic study indicated that the substrate temperature could be lowered by the presence of oxygen species at moderate system pressures (0.3-0.5 atm) and that higher volumetric growth rates required a high temperature source and a moderate pressure system in CVD processing. The principal experimental results were consistent with the thermodynamic predictions. The deposited films were characterized by laser Raman spectroscopy, scanning electron microscopy, and X-ray diffraction. The films were well faceted and uniform, with the growth rates over 10 pm/hr on molybdenum substrates. The crystal size ranged between 1 and 2 microns for a two hour experiment. It was possible to decrease the substrate temperature to below 800 °C in this system.

Jan 1, 1995

By R. Kramer

During foundry sand reclamation process development, molds formed from reclaimed chromite sand showed a rapid decline in tensile strength during thermal cycling tests. Because this characteristic could limit reuse of chromite sand in the. foundry, the sand was examined in detail Scanning electron microscopy, x-ray mapping, magnetic susceptibility, and x-ray diffraction were utilized to evaluate processed chromite sand. It was found that process variables such as binder composition, reclamation temperature, and processing method had a significant effect on the chromite sand particle surface. X-ray diffraction indicated a crystallographic change in the processed sands. Magnetic susceptibility also increased after processing. Diffusion of iron to the particle surface and increased surface roughness were identified as potential causes of the decreased tensile strength in the molds.

Jan 1, 1991

By M. J. Collins

Pressure leaching of zinc sulphide concentrates has been practiced commercially for nearly two decades. The process, which includes direct leaching of concentrate with spent electrolyte in an autoclave, has been commercialized at four separate locations to date. In pilot studies carried out in the Dynatec lab in Fort Saskatchewan, dozens of additional zinc concentrates have been shown to be amenable to pressure leaching. This paper highlights recent improvements in zinc pressure leaching that have been identified through process development studies, and how the experience gained in these studies has been utilized in the development of a new copper pressure leach process.

Jan 1, 2000

By H. Y. Cheng

A pulse column solvent extraction system was evaluated as an alternative to mixer-settlers for the separation and purification of rare earths. The column tested had an inside diameter of 44.5 mm and had 36 sieve plates with a free area of 25%. Pulsing was provided pneumatically using a solenoid valve controlled by a timer so that both pulse amplitude and frequency could be varied. Feed to the column was a mixed rare earth chloride solution containing 10 g RE L-1. The extractant was 5% Ionquest® 801 in Shellsol 2037 diluent. Hydraulic performance of the pulse column was excellent with no propensity towards stable emulsions or crud formation under normal operating conditions. The column was operated in organic-continuous mode with flow rates chosen so that yttrium and the heavy rare earths were extracted with high efficiency while the light rare earths were rejected. Yttrium extraction varied from 83 to 99.2%. Concentration profiles were measured in both the aqueous and organic phases, and, from this data, the height of a transfer unit (HTU), the mass transfer coefficient (Kxa) and the continuous-phase axial dispersion coefficient (Ey) were computed. The HTU ranged from 17-92 an which is within the range of values reported for other (non rare earth) pulse column systems.

Jan 1, 1992

By C. Lupi

Zinc chloride electrowinning presents difficulties in obtaining smooth, compact and dendrite free deposits with a high current efficiency due to the presence of undesirable metal ions. However, it is hard to define a level of impurities tolerable in zinc deposition, and despite a lot of research in this field, the reaction mechanisms of the undesired metal ions are still not clearly understood. In this study, the influence of Fe, Cd, Co, Ni and Cu additions were investigated, as well as their synergic effect on the zinc electrodeposition process from chloride electrolytes and on the obtained deposit morphology. The tests were all performed in presence of TBACl which reduces the harmful effect of such impurities on the zinc reduction.

Jan 1, 2003

By Dale Zacherl, Andreas Buhr, Rainer Kockegey-Lorenz

"The microporous calcium hexaluminate insulating material SLA-92 has been introduced as an alternative to refractory ceramic fiber and other insulating refractory materials. Key properties associated with this product include: high chemical purity, long term high temperature stability up to 1500 °C, low thermal conductivity up to 1500 °C, and high thermal shock resistance. The properties of the new material and various applications in the steel and ceramic industries have been reported in previous papers. The current paper summarizes the industrial application experiences with innovative refractories based on SLA- 92 and discusses potential new applications in various manufacturing as well as energyrelated industries.IntroductionSLA-92 was introduced to the refractories industry in 1998 by van Garsel, et al. [1] as a new insulating raw material for high temperature applications, followed by investigations [2] of long term temperature stability for this new lightweight aggregate up to 1500°C.SLA-92 was developed as an innovative alternative to commonly used refractory ceramic fibers. It has unique properties regarding chemical purity and mineral composition and is a microporous, silica-free calcium hexaluminate (CA6 – mineral name: hibonite)."

Jan 1, 2010

By R. F. Hammen

Copper is one of the most widely used metals in industrial processes and is also present in most mining operations. Extraction of copper from solutions often proves difficult due to the presence of complexing agents. ChromatoChem, Inc. has developed a Solid Phase Extraction (SPE) support (HiPAC) for removal and recovery of metals from wastewater. The HiPAC SPE support employs chelating agents covalently coupled to a long linker molecule. Several solutions containing copper and complexing agents were tested including 1) copper and carbonate, pH 9.8, 2) mixed metals and anions with copper and cyanide, pH 11, and 3) copper and the chelating agent EDTA, pH 11. The copper was extracted from solutions one and two at high pH, but the EDTA containing solution needed the pH lowered to make the copper available for capture. In each example, the copper concentration was significantly reduced by HiPAC SPE treatment.

Jan 1, 1994

By C. P. Broadbent

Due to growing .public awareness of environmental issues and greater sensitivity towards waste management, many countries around the world are implementing more stringent legislation governing the storage and disposal of hazardous wastes containing heavy metals such as As, Sb, Pb, Cd or Hg. These wastes can no longer be dumped without providing clear guarantees that the material concerned is environmentally safe and will not leach toxic elements to the surroundings. In the Netherlands the current dumping charge for chemical waste (i.e. worst category) is $280/t, and for industrial waste this cost reduces to $75/t. If the material can be reused there may be a small positive credit for selling it, for example discard slag as an aggregate to the construction industry. A number of (pyre)-metallurgical operations, mostly associated with the extraction of metals from sulphidic ores, produce arsenic residues in the form of As2O3 containing flue dusts and speises. If the flue dust is of high purity it can be sold, though many traditional uses are being substituted by other materials. In many cases upgrading the quality of the arsenical dusts is not possible for either technical or economic reasons. Traditional practice is to dissolve these dusts in acid prior to precipitation as ferric arsenate, which is at present classified by many countries as industrial waste and can be dumped. Recent work, however, has cast doubt on the stability of arsenates for disposal and alternative disposal routes have been investigated. Tests have shown that up to 10% (dm) As can be incorporated into "glassy" silicate slags with very low levels of arsenic leaching in the cooled product. Calcium arsenate was added to a range of synthetic and industrial slags from the system SiO2-FexOy-CaO-A12O3-AsmOn, under mildly oxidising conditions and quenched subsequently in water. It would appear that this represents an environmentally acceptable method for the disposal of many arsenical residues and there is some optimism that this method will be equally applicable to the disposal of other toxic metal residues.

Jan 1, 1994