Search Documents

By V. Ramachandran

The Amarillo Copper Refinery, the newest and most modern copper refinery in the world, has been in operation for the last eleven years and has a rated capacity of 460,000 st/yr. The tankhouse - a structure that covers 500,000 ft2 under one roof - extends one-half mile in length and is a model of materials-handling efficiency. The use of recently developed and patented* reagent control technology, termed "Reatrol Process", has increased current efficiencies to an average of 98% and has considerably improved the physical and chemical quality of the cathode deposit. The present paper describes the current operations at the Amarillo Copper Plant with special emphasis on tankhouse operation.

Jan 1, 1987

By Gopalakrishna B. Prabhu, David L. Bourell

"Three mol% Yttria-Stabilized Tetragonal Zirconia (YSTZ) was prepared by a sol-gel synthesis technique using zirconium tetrachloride and hydrated yttrium chloride precursors. After drying and annealing at 823K, the particle size was in the range 10 to 20 nm. The zirconia powder was sintered using a uniaxial hot press at an applied stress of 20 to 40 MPa. One hour, isothermal sintering was performed in air after initial heating at 50K/min. Theoretical density was obtained at densification temperatures above 1498K. After sintering, grain coarsening characteristics were studied using constant heating rate anneals followed by quenching, based on a model for grain coarsening in a linear heating rate cycle. The microstructural change was studied using SEM and TEM and the phases were determined using x-ray diffraction.IntroductionThe ability to sinter nanocrystalline materials to full density several hundred degrees below the normal sintering temperatures is one reason for their current interest. [1-5] Yttria Stabilized Tetragonal Zirconia (YSTZ) of grain size of about 300 nm has exhibited superplasticity, with elongations as large as 800%.[6-7] Fine grain size is critical for superplasticity. Retention of the fine grain size during sintering of nanocrystalline powder is important if a material is to exhibit superplasticity or to exhibit physical or mechanical properties associated with the ultra fine structure. This paper investigates the sintering behavior and the grain coarsening characteristics ofnanocrystalline YSTZ.Techniques for synthesizing nanocrystalline materials have been studied in great detail earlier. [8-12] The techniques used to synthesize nanocrystalline zirconia include alkoxide synthesis [9], the chloride method [11], the peroxide method [13] and the acetone-toluene method. [13] In this paper the method used in the synthesis of zirconia is the chloride technique. With this precipitation technique, either zirconium chloride or oxychloride and a corresponding yttrium salt or even pure yttria are used."

Jan 1, 1994

By J. M. Khodadadi

"A computational study of the effect of thermocapillary convection on melting of a droplet under the influence of an incident uniform heat flux is presented. The computations are based on an iterative, finite-volume numerical procedure using primitive dependent variables, whereby the time-dependent continuity, momentum and energy equations in the spherical coordinate system are solved. During the early periods of the melting process, conduction mode of heat transfer is dominant. As the thermocapillary convection is strengthened due to the growth of the melt zone, melting on the side of the droplet is observed to be much faster in comparison to the conduction-only case. Due to the skewedness of the temperature field, a new recirculating vortex is created which promotes melting within the droplet. The effects of the change in the sign of the surface-tension temperature coefficient on the melting pattern are also investigated.1. IntroductionMelting and solidification of materials are important processes which are encountered in nature and numerous industrial applications. Due to the recent upsurge of interest in such processes as spray casting, space radiators, rapid solidification, purification of materials, containerless processing, etc., there is a need to analyze the transport phenomena of melting and solidification in spherical configurations. Specifically, the effect of thermocapillary convection on the melting of metallic droplets has not been addressed at all. Only a few authors have studied the transport phenomena without phase change in spherical droplets. Oliver and DeWitt [l] worked out a series solution for the thermal and surface-tension-driven flow fields for a droplet experiencing an irradiant energy flux in the microgravity environment. Kudo et al. [2] solved the coupled momentum and energy equations numerically for the same problem without dropping the convective terms. Due to the nonexistence of any previous work on transport phenomena during the thermocapillary-assisted melting of metal droplets, this study was initiated to elucidate the features of the phenomenon."

Jan 1, 1999

By Soobhankar Pati

Solid oxide membrane (SOM) technology has been successfully employed for the production of high energy metals such magnesium, titanium and tantalum by directly reducing their oxides. This paper reports on the recent investigation done for calcium production by SOM process from calcium oxide, dissolved in fluoride and chloride based fluxes. This process employs an inert oxygen-ion-conducting stabilized zirconia membrane to separate the inert cathode in the flux from the anode. When the applied electrical potential between the electrodes exceeds the dissociation potential of calcium oxide, oxygen ions are driven out of the melt and through the zirconia membrane to the anode where they are oxidized. Reduced calcium metal deposits or evolves at the cathode depending on the operating temperature. The SOM cell has been electrochemically characterized, and key concepts related to CaO dissociation, leakage current, solubility of Ca in the flux, and hygroscopic nature of the flux relevant to the SOM process are explained.

Jan 1, 2008

By Masafumi Maeda

Our aim in this project was to develop a new copper refining technology utilizing pyrometallurgical treatment and a raw materials preparation technique. In the recycling process; raw material is not an idealized concentrate of copper sulfide but is composed of various types of scrap, industrial wastes such as sludge, ash and slag, and municipal wastes. Since we cannot expect oxidation heat in this process as in sulfide smelting, organic materials are viewed as an alternative energy source. Quality of the copper produced is targeted as 99.99% and an intermediate grade will also be marketable. To benefit the plant, rare metals and other nonferrous metals will also be recovered The overall system is described in this paper, specific topics outlined and preliminary research presented. Current Japanese technology for recycling copper based materials is briefly reviewed.

Jan 1, 1995

By Elliot Schwartz, Julian Szekely

"In this paper we describe an experiment that was recently performed on the IML-2 Space Shuttle mission in which the thermophysical properties of molten metals were measured using electromagnetic levitation. In the planning of these experiments calculations had to be performed to predict the levitation and stirring forces, heating rates, sample deformation, and internal flows within the sample. These predictive calculations were essential for both the planning of the experiments and for the re-planning of experimental runs during the actual Space Shuttle mission.Introduction""Materials Processing in the Computer Age"" involves the use of mathematical modeling to obtain a quantitative understanding of the phenomena that govern materials processing operations. Microgravity, or space shuttle experimentation represents a specific case in point here; the very high cost of the space shuttle flights, the very limited flight opportunities that are available, and the tight resources aboard a shuttle clearly mandate that these experiments be very precisely planned and that all possible opportunities for mathematical modeling be fully exploited.The purpose of this paper is to present the results of calculations performed for the planning of a space shuttle experiment involving electromagnetic levitation and wherever possible present a comparison of the computational predictions with both experimental measurements and asymptotic analyses. Finally we shall seek to discuss the practical implications of both the computational methodologies and the potential experimental findings."

Jan 1, 1994

By Min Zhu, Yu Ji, An-chao Ren

"After being welded in the weld plant, the 100-meter heavy rails with the specification of 60kg/m are found broken during the straightening process in four planes. Failure analysis is made using the optical microscope and SEM with the result showing that the broken rail contains the imperfection of protrusion which exists at the edge of rail foot, about 1 00mm away from the rail end. When the protrusion is peeled off by deseamer from rail surface, cold scratch is generated which causes the rail to be broken during the subsequent straightening process. By adjusting the roll diameter differences between top and bottom roll of universal finishing mill and the height of pass line, it is possible to maintain the rails flat when leaving the mill. This prevents the upsweep and downsweep phenomena and, thus, the imperfection of protrusion can be eliminated. IntroductionThe development of rail transit worldwide has entered into a new era since the 1960s. The hi-tech rail transit system has gradually gained recognition over the world. In particular, the emergence of new-type passenger trains represented by TGV of France, ICE of Germany and Shinkansen of Japan and heavy haul trains as well, has revealed the charming way and more prosperous future of the modern and hi-tech rail transit system to the people all over the world. It should be pointed out that rail transit system is still the most effective solution to traffic jams among urban cities and in the central cities during the 21 '1 century, especially high-speed railway and subway which take overwhelming advantages over air transport, marine transport and road transport in terms of high speed, high efficiency, safety, comfort, environment protection and high flow. With the trend of increasing speed and heavier load of trains, higher product quality of rails is demanded. The rails for passenger dedicated lines require high cleanness, high accuracy in size, high flatness, high surface quality and large size (100-meter fixed length). The rail quality has direct influence on the operating performance of rail and railway traffic safety. The 100-meter heavy rails with the specification of 60kg/m are broken subject to the straightening process in four planes after being welded in the weld plant. This paper analyzes the reason for rails being broken and provides the theoretical proof for determining the rolling process."

Jan 1, 2013

By Jinrong Zhang

Major components of soil were tested for their ability to attenuate cyanide. Feldspar, kaolinite, plagioclase and bauxite are found to degrade cyanide at an appreciable amount mainly through adsorption. A soil near a mining site in northern Nevada was studied in detail using a tall column. Many species of cyanide were anlyzed to determine the mechanisms of the reactions of cyanide with soil. Volatilization, adsorption, oxidation, precipitation and complexing were quantitatively identified, being 5 to 10, 11.7, 4.2, 7.3 and 4 per cent of the total cyanide added, respectively. It is found that the oxidation of cyanide to cyanate is due to the catalytic effect of nickel and copper leached from the soil. Precipitation of metal-cyanide complexes occurred at low pH values.

Jan 1, 1991

A study was undertaken to remove the Se from waste solutions using a raw form of the biomass called Iota Chips derived from the seaweed, Eucheuma spinosum. Removal of Se from solutions was investigated as a function of time, pH, conc. of Se in solution (0.1 to 100 ppm) and lota Chips to liquid ratios of 10-2 to 10-5. For solutions containing initial conc. of 0.1 ppm Se, with the addition of Iota Chips at a solid to liquid ratio of 10-3, the Se conc. decreased to 0.03 ppm in about 3 hours. Iota Chips absorption capacity to the Se and its application to the treatment of the metallurgical processing effluents are discussed.

Jan 1, 1992

By Sergey Komarov, Manuela Diaz, Sano. Masamichi

"Mixing time, bubble behavior and absorption rate of gas injected into a liquid bath through rotary L-shaped lances have been studied by cold models with an effort to improve refining characteristics of metallurgical processes. Two kinds of the rotary lances were tested, namely the single-hole lance and the multi-hole lance. The effects of gas flow rate, bath depth and rotation speed were examined.It is found that when gas is injected through the rotary lances, the mixing intensity and the gas absorption rate are larger than that for the gas injection through stationary lances. The effect of rotation speed decreases as the bath depth and the gas flow rate increase.The multi-hole lance produces much smaller bubbles, which lead to an increase in the volumetric mass transfer coefficient by 3-4 times as compared with the single-hole lance. However, the effect of rotation speed is smaller for the multi-hole lance. The obtained results are explained in terms of the bubble coalescence and fragmentation, the rate of which depends on the departure bubble size and the power supplied to the liquid bath.IntroductionIn recent years, there has been a growing interest in the development of gas injector for metallurgical processes. The majority of the previous work was focused on modification to the injector design to improve mixing and to increase the of chemical reaction rate. These two goals can not be necessarily achieved by the same way. Bottom nozzles and stationary immersed top lances, which have been widely applied to steelmaking processes, are effective for the bath mixing, but have a limit to decrease in the bubble size. This results from a vigorous coalescence occurring between the bubbles when they rise in the molten bath as a bubble swarm.One of the ways to ensure the small bubble size and the effective bath stirring is the gas purging through rotary injectors. A number of studies have been undertaken to improve the refining characteristics by using rotary injectors. All of them are related to aluminum refining. The SNIF equipment (The Spinning Nozzle Inert Flotation) has significantly improved the quality of aluminum products at National Luxemburg Aluminum [1]. Rotary injectors made in the form of a disc have been applied to the Alcoa 622 [2] and the GBF processes [3]. A study of the gas injection by a rotary impeller has been carried out by C. Leroy and G. Pignacelt [4]. All researchers note the significant improvement in removal of sodium, calcium, hydrogen and non-metallic inclusion."

Jan 1, 1996

By L. Sh. Tsemekhman

A new technology for the treatment of copper nickel-containing concentrate after high-grade matte flotation to blister copper with the production of liquid silicate slags in a vertical autogenous unit with upper oxygen blow has been considered. The copper and nickel behavior in the process of sulphide copper concentrate interaction with silicate melt containing oxide copper has been studied. The general mechanisms of such interaction are found.

Jan 1, 2003

By P. R. Khangaonkar

The variety of intermediates, middlings, complex materials and wastes produced in the conventional processing of tin ores as experienced in the tin industry in South East Asia is reviewed. The problems associated with the treatment of these materials so as to produce useful products by hydrometallurgical or pyro-cum-bydrometallurgical approaches are discussed. Results of treatment of amang middlings consisting of cassiterite, struverite, ilmenite, zircon, monazite etc by chlorination with carbon tetra chloride are presented. The efforts to leach tin without letting iron coming in, by alkali leaching of certain wastes of tin processing are also briefly indicated. It is felt that pyro-cum-hydrometallurgical approach can help a viable treatment of these materials so as to obtain usable or value added products.

Jan 1, 1994

By Jianhong Dong, Min Chen, Cuihuan Huang, Bo Li, Nan Wang

"Scale layer can be formed on the slab surface in the areas of secondary cooling and strand discharge during continuous casting process. From 1000 °C -1200 °C, the influence of steel composition on the stable oxide phases inside scale layer, particularly the types of alloying elements including aluminum, silicon and chromium, is investigated under different partial pressures of water vapor by the calculated predominance diagrams of iron oxide as well as its intermediate compounds formed with other metal oxides, and the stable oxide phase composition within scale layer under the working condition of secondary cooling is discussed. At lower partial pressure of water vapor, only a iron spinel (or ferrosilicate) phase is the stable phase with any alloying element contents in steel composition, whereas the stable phases are FeO and iron spine! (or ferrosilicate) inside the scale layer at higher partial pressures of water vapor .IntroductionOxide scale formation on the surface of cast and rolled products because of oxidation by the surrounding oxidizing atmosphere is a significant disturbance factor in steelmaking. The yield loss of iron because of scale formation is considerable during continuous casting and hot rolling process. Surface quality more often is impaired by scale property, which increasing the difficulty of quality assurance, dimensional accuracy and performance control. Furthermore, a potential source for subsequent surface cracking (hot shortness) can be caused by the enrichment of scrap residuals (Cu, As and Sn) at the steel substrate surface as a result of steel oxidation [1-2]. In flat products manufacture via thin slab casting technologies, these phenomena are particularly pronounced and require enhanced development efforts in descaling efficiency [3].Compared with the scale formation in continuous casting, the quantity of scale formed during hot rolling and reheating in the rolling mill is larger, and control of scale formation and descaling is a long-established task in hot rolling. Therefore, extensive research and development work have been carried out, including the effects of heating and rolling temperature on the thickness and microstructure of scale layer, heating time and furnace atmosphere, cooling mode, and steel composition on the scale formation, more attention has been given to the control of scale formation during reheating and hot-rolling process. On the other hand, hardly any specific efforts and countermeasures are taken in continuous casting, and very less research has been done despite the network-type crack on the as-cast strand surface caused by the subscale enrichment of scrap residuals [ 4-7]."

Jan 1, 2014

By Abhoy Mukherjee

The Luanshya Smelter is a traditional Reverberatory Smelter which once worked with up to three coal-fired reverbs, and now operates one Reverb and one hot Peirce- Smith Converter, projected to produce approximately 42.000 tons per year of copper anodes. The aim of this study is to select a smelting technology which best fits the upgrading of the Smelter, such that low capital and operating costs are achieved for the projected design production capacity of 60.000 tpy, limited by the available supplies of concentrates. An equally important requisite is the compliance of present and future environmental regulations, which determines the need to install and Acid Plant to treat the smelter primary gases. In the process selection study, the following technologies were analyzed, at a Conceptual Engineering level: the Oxy-fuel Burner Reverb, the Teniente Converter, the CONTOP Cyclone Smelting Reactor, and further, the Ausmelt Furnace, the engineering of which was provided by the proprietary firm. The engineering of the other processes was developed by INDEC, which also integrated the comparative analysis of the four options. The analysis of a comprehensive set of technical factors, including integrated smelter metallurgical models, together with the evaluations of economical features, led to the selection of the CONTOP Smelting Technology for the modernization of the Luanshya Smelter.

Jan 1, 1999

By R. D. Osmanson

A series of batch roasting tests was performed on minus 1/2 inch gold bearing refractory samples from the Gold Acres deposit, and 67 select particles were polished and the sulfide alterations were examined microscopically. The suite of specimens represents two hour batch roast treatments at 600°C, 700°C, 725°C, 750°c, 800°C, and 900°C. Auriferous pyrites were found to alter sequencially to pyrrhotite, magnetite and finally to hematite. It was found that the decrease in cyanidation extraction with high temperature roasting is likely due to the increas ing stability of magnetite and more crystalline hematite, and the decrease in porosity with these phases which occlude the gold. Gold has been noted to occur very early in the mineralizing sequence, with gold being found in quartz and in clay/carbonate rock matrix. No gold was found in the two pyrite phases, but numerous gold grains were found in pyrrhotite after pyrite and in subsequent iron oxides. Gold mineralization had apparently ended by the time base metals were introduced into the deposit.

Jan 1, 1987

By N. V. Gorelikova

A new type of zirconium mineralization has been recognized in the Devonian volcanic rocks from an orogenic depression in the Central Kazakhstan. The most characteristic features of this deposit are the fine-grained nature of the zirconium mineralization, an unusual texture of the zirconium ores, and a close association of zirconium with phosphorus in the ores. Zircon grains form fine globular aggregates with the features of hexagonal crystal habit. In addition to crystalline zircon, the ores contain metacolloidal zircon, similar to hydrozircon. The morphological and textural features of the zirconium ores suggest that the deposition of ore deposits took place at a low temperature from colloidal solutions. It is believed that this deposit should be considered to be a new type of zirconium mineralization that is related to low-temperature hydrothermal processes.

Jan 1, 1995

By J. W. Tsai

Both diamond crystals and diamond films were grown on silicon and copper substrates using a methane/hydrogen gas mixture as a precursor with thermal CVD techniques at low pressure environment. In addition to diamond particles, other crystalline phases including graphite and aluminum silicon carbide were observed on the substrate surface. ?The grown materials were analyzed with X-ray diffraction, electron microscopy, Auger electron spectroscopy and optical microscopy. Most synthesized diamond crystals were twinned. The flow rate of reactant gases, substrate nature, substrate temperature, decomposition temperature of the precursors, total pressure of reaction chamber, methane/hydrogen ratios and other possible parameters were varied during the growth processes, and the significant effects of these factors on nucleation and growth rate were evaluated.

Jan 1, 1989

By Jinfu Xu, Youqing Cao, Yuting Lv, Hang You, Peng Jiang

"In present work, we reported the fabrication of composites consisted of M42 powder metallurgy high speed steel and 45 steel at one step via spark plasma sintering (SPS) technology. The interface microstructure, compositions and microhardness with the interface forming mechanism were investigated. The results show that the morphology and microhardness within the M42/45 steel interfaces exhibit a gradient distribution. The interfaces possessed a transition layer up to 10.2 ?m with few distortions and microcracks. The formation of M42/45 steel interfaces were driven by both fusion and diffusion processes. The former one was primary at the early sintering process, while the later one becomes dominant over the followed sintering process.IntroductionPowder high-speed steels have been widely used in cutting tools, cold-hot tools and dies, as well as in cut materials and structure parts with wear resistance and high-temperature resistance, due to its high hardness, good wear resistance, desirable cutting toughness and favorable hot hardness [1-2]. For materials of some parts in practical production, not only the favorable toughness is required to resist the impact action, but also the high hardness and exceptional wear resistance are demanded. According to the functional requirements and working conditions, bimetal composite materials are prepared in a certain mode, proportion and distribution, by designing two metals with different chemical and physical properties [3-6]. Considering the composites exhibit different properties in different positions of the parts with a combination of the advantages of two metals, they can obtain enhanced properties that the single one can not achieve."

Jan 1, 2012

By C. Frias, M. Garcia, G. Diaz

Advances in hydrometallurgy promoted by Tecnicas Reunidas are providing increasingly simple and clean means for controlling the entire lead recycling chain. Used in parallel with pyrometallurgy, these processes allow furnace temperatures to be reduced and fumes and atmospheric pollution to be minimised. Furnace slags are digested, and residues (mainly gypsum) are non-toxic and convertible into marketable products. In addition, the global economy of the process is substantially improved by reducing the operating cost, increasing the lead recovery above 99% and obtaining a 99.99% pure lead product. These new PLACID and PLINT processes may provide the cleanest and healthiest practicable means for recycling lead from batteries.

Jan 1, 2000

By Petrus Christiaan Pistorius, Farzin Fatollahi-Fard

The production of titanium oxycarbide – a consumable anode material used in molten-salt processes for electrowinning titanium – from heavy mineral concentrate, such as a high-titania leucoxene and natural rutile is described. The oxycarbide is prepared by carbothermic reduction of the oxide at elevated temperature. Particle size distribution (of the titanium oxide raw material) and temperature have large effects on the kinetics of the reaction, which seem to follow a “shrinking-core” model. It is anticipated that low porosity (in the anode pellets) would be advantageous during electrolysis. Particle size distribution, extent of reaction during carbothermic reduction, and sintering temperature are expected to affect pellet porosity after sintering, and are being tested experimentally.

Jan 1, 2015