Search Documents

By R. Svensson

Mill linings play an important role in all comminution processes with tumbling mills. The selection of the lining profile and the lining material has a great impact on over-all grinding cost and mill throughput. The cost of the lining itself is minor in comparison with media cost, energy cost and the value of the material produced in the mill. The total scope must be considered when mill linings are selected. This paper presents case stories and explains the technology behind: -different lining profiles in rubber and steel -OREBED magnetic lining -Steel-cap rubber lining

Jan 1, 1994

By T. P. Meloy

Riffles on a shaking table have a major effect on particle separation. This effect is modeled in a spreadsheet.

Jan 1, 1993

By Ihsan Berk Tulu, Ted Klemetti, Deniz Tuncay

"The Analysis of Retreat Mining Pillar Stability (ARMPS) program was developed by the National Institute for Occupational Safety and Health (NIOSH) to help the U.S. coal mining industry to design safe retreat room and pillar panels. ARMPS calculates the magnitude of the in-situ and mining-induced loads by using geometrical computations and empirical rules. In particular, the program uses the “abutment angle” concept in calculating the magnitude of the abutment load on pillars adjacent to a gob.In this paper, stress measurements from U.S. and Australian mines with different overburden geologies with varying hard rock percentages were back analyzed. The results of the analyses indicated that for depths less than 650 ft, the ARMPS empirical derivation of a 21° abutment angle was supported by the case histories; however, at depths greater than 650 ft, the abutment angle was found to be significantly less than 21°. In this paper, a new equation employing the panel width to overburden depth ratio is constructed for the calculation of accurate abutment angles for deeper mining cases.The new abutment angle equation was tested using both ARMPS2010 and LaModel for the entire case history database of ARMPS2010. The new abutment angle equation to estimate the magnitude of the mining-induced loads used together with the LaModel program was found to give good classification accuracies compared to ARMPS2010 for deep cover cases.INTRODUCTIONIn the early 1990s, the Analysis of Longwall Pillar Stability (ALPS) was introduced by Mark (1990) as a chain pillar design software and was generally accepted and used by the U.S. coal mining industry. Following the success of ALPS, the National Institute for Occupational Safety and Health (NIOSH) developed the Analysis of Retreat Mining Pillar Stability (ARMPS) program for designing retreat mining pillars using a similar approach as ALPS (Mark and Chase, 1997). The Australian mining industry also recognized the success of ALPS, and Colwell, Frith, and Mark (1999) calibrated the program to Australian conditions. The ALPS and ARMPS programs draw their strengths from the large databases that are used to calibrate them (Mark, 2009). However, following the Crandall Canyon Mine collapse in 2007, NIOSH had to reconsider the pillar design criteria used in deep-cover retreat mining (Mark, 2010). The ARMPS overburden load prediction algorithm was improved to more accurately predict the loading of narrow panels with high overburden depths by implementing the pressure arch concept, and this new version is called ARMPS2010."

Jan 1, 2019

By C. S. Vender

Knife River Coal Mining Company's Beulah Mine is a multiple seam lignite operation located in western North Dakota. The mine began production in 1963 with annual production at 450,000 metric ton and now produces 2.2 mm ton. As development progresses, operations have advanced into more complex geologic areas. Various techniques have been analyzed to maximize coal recovery in a cost effective manner. Additional studies are on-going to determine what changes will be implemented as we encounter deep wet sands in the reserve area.

Jan 1, 1991

By N. S. Tanious

This paper summarizes results from an investigation into possibly the largest coal pillar failure in the USA. The newly opened coal mine worked an 3.35 m (11 ft) seam under overburden depth that ranged from 91 to 671m (300 to 2200 ft) . The mine main entries, and the enclosed pillars, experienced a massive slow squeeze. The squeeze could not be controlled and the mains were lost. A new set of mains were driven. Entry convergence (closure) measurements were carried out behind the advancing face to monitor stability. Pillar stresses were also measured under four different depths of overburden: 229.433, 472.579 m (750,1420,1550, and 1900 ft). The strength of pillars in the new mains was calculated from the loads that triggered the failure in the old mains, using three pillar strength formulas. The stress measurements showed that the new pillars supported more load than their predicted strength, indicating that current strength formulas are inadequate under deep conditions.

Jan 1, 1992

By D. Suarez

The work of engineers responsible for the design and performance of mine facilities is often challenged by economic and practical constraints in the field. Problems have developed in implementing design criteria dictated by persons or agencies not familiar with the dynamic nature of mine engineering. Regional and site-specific conditions frequently require changes to standard designs, or the use of a completely innovative approach, which is not provided for in the regulations. The implementation of engineering design, therefore, usually requires a hard-sell approach to management and regulatory agencies that allows for a happy-medium to all parties concerned. Flexibility on the part of the regulatory agencies is needed to solve operational and environmental problems with sound engineering. Typical hydrologic issues which will be discussed fall in the following general categories: ? Design criteria for sizing water control structures (i.e., culverts, diversion and sedimentation ponds, ditches, etc.) ? Implementation (construction and operation) difficulties ? Regulatory compliance ? Reclamation planning with hydrologic considerations ? Protection of groundwater resources

Jan 1, 1986

By Takashi Goto

In 1968 three historical rockbursts had occurred at Bibai Coal Mine in Hokkaido. At the time they had been observed by several seismic observatories as natural earthquakes away more than 100km from Bibai City. These facts taught us that the occuerrence of failure yielded in underground opening that was accompanied with seismic wave could be observed by seismometer on the surface. After two years from this desaster, the study concerning to microseismic events generated from underground mining panels has been begun by researchers with heart-throb.

Jan 1, 1982

By C. O. Brawner

A recent advance in slope dewatering-depressurization and stabilization is the use of vacuum assist horizontal drainage. (Brawner and Pakalnis) Horizontal drains have been used for several decades to reduce water pressures in slopes to improve stability. The benefit from vacuum assist arises from an increased hydraulic gradient caused by an induced negative atmospheric pressure. A research program included a laboratory model whereby the effects of vacuum drainage were evaluated. Three case studies are described where the technique has been successful. The first is in a rock slope where flows increased from 0.1 1/min. under gravity drainage up to 1.2 1/min, upon vacuum. The second study involves installation of 17 drains placed at a slightly downward gradient to intercept and de- pressurize aquifers under a major tar sand deposit in Canada. The third study was on a large open pit copper mine in British Columbia where flow increased about 30 per cent.

Jan 1, 1984

By K. G. Black

When one's attention moves from the control of a process unit or from the control of a department of similar units, to the control of an entire plant, two things must change. One is the techniques of control, and the other, the goal or purpose of control. The goal is no longer maintaining a certain quality of product or maintaining a particular flow rate through a process unit. The goal becomes economic - how to make the most money out of the plant. The principal control techniques become those of optimizing, rather than regulating. It is quite common to discuss the control of an entire plant in terms of three levels of control l; regulation, supervision, and optimization. Regulation is the control of inputs to a process unit at desired values. This is accomplished by two or three mode analog controllers or DDC loops. The second level of control is the selection of these desired values, e.g., set-points of the regulation controllers. The third level is to make such adjustments or corrections to the supervisory calculations so as to optimize the plant profit. It is immediately evident that supervisory control and optimizing control are intimately related, and a distinct dividing line cannot always be drawn between the two. Some authors prefer to add even more levels such as adaptive control and management information systems, but we believe our point is well made without further division of the functions which are necessary for complete plant control. To accomplish the economic goal, that is, the optimizing (maximizing) of the profit of a mineral processing plant, the plant should ideally be operated as if it were a separate company, buying its raw materials on the open market and selling its products on the open market. While petrochemical plants endeavor to operate in that manner, unfortunately this is not true of a mineral processing plant. The plant manager has to accept the amount and quality of ore the mining department delivers to him, and the products (concentrates) are delivered to another department of the company for further refining. In some cases he may sell

Jan 1, 1972

By C. B. Daellenbach

The influence of reduction roasting and thermal shock on the grindability of a refractory low-grade Michigan iron ore was examined in bench scale tests. The quantitative effects of the various treatments were evaluated at three sieve levels: 48, 100, and 400 mesh, using ball mill grindability and work index parameters as response indicators. Data from the testing program were analyzed statistically as a means of isolating the effects of cooling rate, roasting temperature, and ore chemical condition. All three variables were found to have an important influence on the grindability of the treated ore; ore chemical condition and roasting temperature had the most pronounced effects.

Jan 1, 1970

By Marshall D. Himes

The Pima mine, 39,000 ton per day copper mine, is located 17 miles south of Tucson, Arizona. The mine is in a sequence of Paelozoic and Mesozoic sediments striking east-northeast and dipping southeasterly intruded by a Tertiary quartz monzonite porphyry. The Paleozoic Permian(?) dolo¬mites, limestones, and sandstones have been altered to talc-silicate skarn, marble and quartzite. The overlying Mesozoic Triassic(?) clastic sediments have undergone some recrystallization and hydro¬thermal alteration. The clastic metasediments are divided into three distinct lithologic units, lithic arenite, arkose, and inter¬bedded and overlying black argillite. Three types of hydrothermal alteration in the clastic rocks are propylitic alteration (epidote, chlorite and quartz, with or without sericite), quartz-sericite alteration, and potassic alteration (K-feldspar and quartz, with or without sericite and chlorite). The porphyry has undergone potassic alteration. Dominant structures are an east-west post mineral fault in the western part of the pit, and strong low angle faulting and shearing which truncates the ore body at depth. Two joint sets, one parallel to bedding and the other at right angles to bedding are prominent in the mine. Faulting is in two dominant directions, one striking northwest, dipping northeast and the other striking northeast, dipping northwest. Mineralization is predominantly disseminated pyrite and chalcopyrite, and molybdenite-quartz veinlets. There are lens important amounts of magnetite, hematite, sphalerite, galena, tennantite and bornite. Mineralization is believed to be both structurally and chemically controlled.

Jan 1, 1972

An atomic force microscopy (AFM) has been applied to study the adsorption of collectors on mineral surfaces in a copper/molybdenum flotation system. AFM images show that collectors absorb on chalcopyrite surface in patches at pH 11. A study of temperature effect on surface morphology excludes the possibility that these patches are nanobubbles forming on hydrophobized mineral surface. Hydrocarbon oil absorbs on molybdenite quickly, while KEX (potassium ethyl xanthate) has little affinity for molybdenite. Pyrite is much more reactive in water and its surface is easily coated in Ca(OH)2 solutions at pH 11. Based on the obtained AFM images, the adsorption of chemicals on mineral surface and its impact on copper/molybdenum flotation were discussed.

Jan 1, 2012

By S. K. Kawatra

In order to meet federal air pollution guidelines, it is necessary to remove a considerable quantity of sulfur from many North American coals. This may be accomplished by oxidizing the sulfur to water soluble forms, followed by washing the coal. Selective oxidation of the various sulfur forms can be accomplished through the use of a variety of types of bacteria. In this paper, the various bacteria and their requirements are described, and processes using bacteria to remove coal sulfur are discussed.

Jan 1, 1987

By Norman K. Olson

A geologic investigation of mineral resources in South Carolina first began in 1825 when the General Assembly authorized Lardner Vanuxen to conduct a "Geological and Mineralogical Survey of South Carolina." Vanuxen, South Carolina's first State Geologist, reported in 1826 on the limestones (marble) of the Piedmont which during those early years, were burned in many shall, scattered kilns in the region wherever suitable raw material was available. He also mentioned the possibility of using marl from the Atlantic Coastal Plain province for direct application and enrichment to the soil. Since before the year 1844 industrial minerals in South Carolina have been commercially produced literally from A to Z, asbestos to zircon. The first pub¬lished reports of actual commercial production, not just an occurrence, are referenced in Table 1 for 33 known industrial minerals and rocks in South Carolina. Known or suspected occurrences of undeveloped non-metallic mineral resources in South Carolina await future verification by geologic mapping, sampling (including coring), possible beneficiation, and market analysis. These industrial minerals and rocks include, but are not limited to, special, clay minerals (e.g. bentonitic clays, zeolites and others), sillimanite, argillite (lightweight aggregate), kaolin (alumina) and marl (underground storage and tunneling medium). In addition other non-metallic minerals, once mined but still worthy of reconsideration, include topaz (industrial), heavy minerals, barite, feldspar, and monazite. Finally, possibilities for new reserves, as an expansion of existing mine output, might develop for fuller's earth, limestone (lime), sericite (finely divided mica), vermiculite, kaolin (paper coating and filling, other filler), and metallurgical gravel. Official South Carolina data from the U. S. Bureau of Mines for 1974 indicated a total value of mineral production of $105.2 million. During 1974 production consisted of cam-on clays, (brick and tile), fuller's earth, kaolin and vermiculite

Jan 1, 1977

By A. W. Khair

This paper presents an analysis of surface subsidence characteristics in room and pillar mining using physical models and laser holographic interferometry (holometry). The analysis included the effect of various geometric parameters and different overburden materials (sand and gelatin) and resulted in the formulation of a more realistic model material for laboratory simulation of typical geologic overburden. Previous work using this technique involved the use of sand to model over- burden and detailed results are presented elsewhere (1). The main emphasis of this work was to develop a gelatin based mixture which would provide a better model. Initial work during the development of this model included testing various ingredients and monitoring the time dependent characteristics of the model, such as the surface penetration resistance. This value indicated changing deformability/ridgidity of the model with time. Once several models had been developed, holometry techniques were applied. Initial tests showed that the stiffness of gelatin created a bridging effect over the mine models, thus restricting deformation. At this point, a 0.5 inch (1.27 cm.) layer of sand was placed directly over the mine model with the gelatin mixture on top. The approach was to model different zones of overburden movement that exist as an extraction occurs (2). The sand would represent the caved and fractured zones which occur above the excavated area. The gelatin models the continuously deformed zone which occurs between the fractured zone and the surface. Holometry techniques applied to this model yielded successful results.

Jan 1, 1986

By J. Schoenbacher

Park City Municipal Corporation (PCMC), long before being recognized as an Olympic venue was known as one of the great American silver mining towns. During a century of active mining, the Park City mining district produced millions of ounces of silver in addition to a substantial amount of mine tailing waste. Since 1985 the City has been remediating these impacts with state and federal oversight. One particular challenging CERCLIS site, that was previously a historic mine tailings pond is known as Prospector Square Development (CERCLIS Listing Silver Creek Tailings UTD98051404). This site has been very challenging due to the metals that impact the shallow ground water that eventually drain into the Silver Creek Watershed. To address the water quality impairment the City and Missouri University of Science and Technology teamed up to investigate the feasibility of constructing a horizontal-flow wetland to treat this pollutant source. This effort began with the building of a pilot cell in June of 2004 and lead to the construction of a full scale horizontal-flow wetland in the fall of 2008. The design of the pilot and full scale biocell was based upon lab-scale research conducted by the Missouri University of Science and Technology. In October of 2008, the Prospector Drain effluent was introduced to the system and to date analytical results reveal that the biocell is treating the Prospector Drain outfall below the Silver Creek Total Maximum Daily Load (TMDL) endpoint goals for zinc .39 mg/L and cadmium .00075 mg/L. The water chemistry of the influent, that originates from the historic silver mine tailings pond, is impaired with zinc and cadmium and has low iron with a pH of roughly 6.5. The construction of this unit encountered many challenges related to constituent relations, regulatory scrutiny, constructability and start-up. Nonetheless, since implementation this unit is considered a success for improving water quality within the Silver Creek Watershed.

Jan 1, 2011

The Bagdad mill, built in 1977, was de-signed for a mill capacity of 36,300 tpd. An ABC (Autogenous Mill-Ball Mill-Crusher) grinding circuit was chosen. The original mill contained three completely independent grinding circuits, each containing one 9.75 m diameter by 3.96 m long fixed speed autogenous mill, one 4.72 m diameter by 6.71 m long ball mill and one 2.13 m diameter short-head cone crusher. Total installed power per grinding circuit was 8,464 kw with 5,966 kw in the autogenous mill, 2,237 kw in the ball mill and 261 kw in the crusher. (See FIGURE I--Major Equipment Flow Diagram.) The autogenous mills were designed to be able to operate semi-autogenously but were never converted to SAG. As a result of this design, only about 4,100 kw of the designed power is utilized in the autogenous mills. The grinding circuits are closed with 2.44 m by 6.10 m double deck vibrating screens. Screen oversize is returned, by a series of conveyors, underneath the mill coarse ore stockpile to feed the crushers. Variable speed belts feed the crushers and control power draw. Crusher product reports directly to the tail end of the autogenous mill feed belt. (See FIGURE 2--Typical Crusher Feed and Product Size Distributions.) Tramp iron in the autogenous mill-crusher circuit is handled in a unique way. A magnetic sensor detects the metal. This closes a gate which directs the crusher feed onto a separate belt which bypasses the crusher and returns the material to the autogenous mill feed belt.

Jan 1, 1992

By I. S. Parrish

This article offers one of the infrequent looks at Chinese mining. It includes a brief review by Parrish of a tungsten symposium held there and his comments on and impressions of the mines he visited. In early Oct. 1981, a Symposium on the Geology of Tungsten was held in the Peoples Republic of China. There were approximately 100 participants. Half of them were Chinese. The remainder included representatives of the United Nations, geologists from other nations in Southeast Asia, and 10 invited specialists from other countries. The invited guests included K.F.G. Hosking of the Camborne School of Mines, United Kingdom; C.S. Hutchinson of the University of Malaysia; K. Mattson of LKAB Int. AB, Sweden; T. Kwak of Latrobe University, Australia; K. Sato and S. Ishihara of the Geological Survey of Japan; M. Clarke of the Department of Mineral Resources, Indonesia; P. Bateman of the US Geological Survey; and the author. R. Horsnail of Amax was also invited but was unable to attend because of delayed visa clearance. The meeting was noteworthy because the Chinese were presenting more than half the papers. In addition, following the formal session, everyone was taken to the famed Jiangxi tungsten district and toured four mines there. Organization and Background The idea for a symposium on tungsten geology was brought up in late 1979 during a visit to China by the Economic and Social Commission for Asia and the Pacific (ESCAP) and, in particular, by members of the Regional Mineral Resources Development Centre (RMRDC) of the United Nations. Discussions continued and in the spring of 1981 invitations were sent to selected geologists throughout the world. China's Ministry of Geology handled arrangements, scheduling, and logistics. Travel to China and all correspondence before the symposium were coordinated by the Bandung, Indonesia Bureau of RMRDC. All costs in China were met by the Peoples Republic of China. Airfares and "per diem" enroute for participants were paid by respective governments, sponsors, or individuals. On Oct. 10, visiting participants entered China from Hong Kong. The author and a few others traveled by train to Guangzhou (Canton). Most of the group flew in the next day. The entire group was then taken to Nanchang, traveling by sleeper train and arriving on Oct. 11. The symposium group stayed at the Kiangsi Hotel, where the meetings were held. Meetings Oct. 11 was a day of orientation and rest. The group was taken to an art museum and treated to a Chinese opera movie. The formal meetings began on Monday, Oct. 12. Simultaneous translations aided presentations, though more than half the Chinese speakers delivered their talks in English. The acoustics and sound system were excellent, and the Chinese provided 35-mm and overhead projectors. There was no screen, however, and the yellow, painted wall that was used detracted from projection clarity. In general, the Chinese papers were detailed, thoughtful, and professional. Some, naturally, were stronger than others. Taking them as a unit, one derives the following sequence to the Chinese approach to tungsten exploration: (1) Geologic investigations with mapping at a scale of 1:200,000 accompanied by only minor geochemical or geophysical work. (2) Geophysical investigation with regional gravity and magnetic surveys directed toward identifying deep, tectonic systems and seeking granites in thick, crustal environments. (3) Geochemical sampling in-

Jan 6, 1982

By Marcie A. Greenberg

The Fence Lake Project is located in the Salt Lake coal field, an extension of the San Juan Basin. Geologic formations exposed in the Project area range in age from late Cretaceous to Quaternary. Coal is encountered in the Moreno Hill Formation (upper Cretaceous). Salt River Project (SRP) followed the basic textbook approach for the exploration, regional appraisal, detailed reconnaissance, detailed surface appraisal and three dimensional sampling (physical exploration). SRP is exploring this property as a potential fuel source for the Coronado Generating Station. Therefore, for the physical exploration stage, the quality sampling program was designed from a utility company viewpoint to determine possible impacts to the Station. Exploration drilling was completed in spring, 1982; September, 1982, and summer, 1984. Engineering, environmental, and land acquisition studies were added in the Summer, 1984 Program to more closely evaluate the potential Fence Lake Project coal supply option for the Coronado Generating Station. Studies, including drilling, are ongoing-at this time.

Jan 1, 1984

By H. F. King

In 1982, the result of a 3-year study was published as "A Guide to the Understanding of Ore Reserve Estimation". The principal conclusions were that computation formed only part, and perhaps not the most important part, of an estimate and that the estimate should recognize that geological, mining engineering and metallurgical judgements formed an essential part of the eventual result. Subsequent expectation/realization studies of several mines have produced case histories which form the principal basis of the paper. These imply that geology is even a larger factor than thought earlier.

Jan 1, 1985