Search Documents

By Djavid Mohammad

Over the next several years, the storage capacity of the Metropolitan Water Reclamation District of Greater Chicago?s Tunnel and Reservoir Plan will be increased by 14.8 billion gallons through the addition of two large off-line reservoirs: the McCook and Thornton Reservoirs. The Thornton Reservoir will be constructed at the terminus of Calumet TARP System. The constructed TARP system will be connected to the Thornton Reservoir via connecting tunnels and gates systems. The connecting tunnels will comprise of: an upgradient transition tunnel, steel lined bifurcated tunnel for conveyance and control of flow, downdradient transition tunnel, and energy diffuser at tunnel portal. A large, approximately 250-foot-long, 69-foot-wide, and 40-foot-high, rock cavern will be excavated at an average depth of 320 feet to house the bifurcated tunnel system and associated six large control gates, each 12.5-ft by 28-ft wheel gate. Presented in this article are discussions about the TARP system, the Connecting Tunnels and gates Project, regional rock conditions, evaluation of reservoir?s wall stability for evaluation of tunnel penetration, and design challenges facing during design of the: rock cavern hosting the bifurcated tunnel system and gates and associated tunnels and shaft.

Jan 1, 2008

By Erich U. Petersen

Recognition of mineralogical and chemical zoning patterns associated with mineralization is an integral part of mineral exploration. Even though the origin of zoning may not always be known, zoning patterns as expressed by the systematic distribution of ore and gangue minerals, alteration or elemental assays (soil and rock geochemistry) have received much attention and are extremely useful in guiding exploration efforts toward locating economic mineralization. By contrast, the potential of using zoning information recorded in solid-solution minerals to address practical geological-engineering problems has received less attention. Solid-solution minerals can provide critical information for common problems faced in exploration, mine development and valuation. Mineral zoning information from solid-solution minerals can now be easily obtained because advances in electron microprobe instrumentation have made these instruments a most efficient, accurate, economical and practical tool for analysis of large numbers of samples. Now entire mines and districts can be studied in a timely and cost-effective manner as required by modern mineral exploration and mining practice. This article shows how knowledge of the composition of fahlore minerals can be used in addressing important problems in exploration, development and valuation. Situations are described in which drilling intersected "low grade zones" (Case one: Orcopampa, Peru, precious metal system) and where there was a need to determine the "lateral correlation of multiple ore intercepts" (Case two: Sheep Creek, Montana, sediment-hosted sulfide deposit).

Jan 1, 1992

By George K. Schenck

INTRODUCTION Recent advances in high-pressure water jet technology can be effectively employed in mining and tunneling. The new equipment is based on available industrial hardware such as pumps, nozzles, and rotary swivels and seals, and is compatible with present mining and tunneling techniques. Principal advantages of water-jet assisted cutting relative to standard cutting are higher production rates, lower dust levels, and reduced fines. When used on rock and coal miners, water jets mean that relatively smaller and cheaper machines can be purchased. If properly applied, the combined effect is lower cost and significantly improved health and safety. While commercial use of high-pressure water blast cutting and extraction of rock (and concrete) already has a firm foothold in Europe, application of this new technique is just beginning in America. This paper begins with current American applications of high-pressure water jets for drills, for slotting and channeling machines, and then discusses the emerging technology for initiating rock failure in conjunction with drag bits on coal plows, continuous miners and boom-type miners (roadheaders). The focus of this paper is use of high-pressure water jets for cutting rock. High-pressure water jet cutting utilizes water above 70 MPa and currently reaches to 300 MPa and above. Some informatfon is included on low pressure "wethead" coal shearers and boom miners with water pressure to about 15 MPa.

Jan 1, 1983

By John Murray, Daniel Ebin, Robert Gould, Yiming Sun, Lizan Gilbert

The Atlanta Plane Train Tunnel West Extension is being constructed at Hartsfield-Jackson Atlanta International Airport using the Sequential Excavation Method (SEM). The tunnel has shallow ground cover and mixed-face conditions and passes underneath the SkyTrain and MARTA stations and airport terminal buildings. It includes a twin tube Bifurcation with a span of over 45 feet and ground cover of 12 feet. A flat roof is being constructed at the Bifurcation to maximize rock cover and minimize surface settlements. This paper focuses on design and construction challenges for the Bifurcation and tunneling beneath the world’s busiest airport, while minimizing impacts to operations.

Dec 1, 2022

By Frederick McNeill, John Harper, Mahmood Khwaja, Shawn Lavoie, Timothy Cloughert, David Polcari

City of Manchester, NH, is implementing a 20-year plan to control and significantly reduce overflow of its sewer system. The long-term control plan had called for large scale box culvert installation through downtown Manchester. The City and the project team evaluated, and eventually selected, tunneling as an alternative to mitigate construction related impacts for open trench approach. This paper provides an overview of the alternative evaluation process; discusses the development of the preliminary design for the 12,000 feet long, 12-ft internal diameter tunnel, including plan and profile selection, subsurface conditions, drop shafts and the anticipated packaging of the separation areas.

Dec 1, 2022

By A. D. Davis, J. L. Sorensen, C. J. Webb

Environmental impacts from acidic mine drainage are growing national concerns that are particularly acute in the headwaters of the Rocky Mountain region. In the Black Hills of South Dakota, approximately one thousand mines are inactive or abandoned, most of them in the headwaters of major drainages. This paper examines the Bear Butte Creek basin, a heavily mineralized watershed with significant historical mining impacts and a surface gold mine permitted in 1997. The watershed loses its surface discharge to swallow holes in the karstic Madison Limestone. The integrity of the aquatic ecosystem was monitored with a suite of sitespecific bio-indicators. Stream surveys covered the entire reach of Bear Butte Creek from near its headwaters to the swallow holes in the Madison aquifer. Data from the stream surveys, water-quality sampling, and bio-indicator surveys clearly showed that water-quality impacts are limited mainly to Strawberry Creek and to the area of Bear Butte Creek near and downstream of the town of Galena.

Jan 1, 1999

"Mining of ore bodies that are located at great depths enforces long distances to move the excavated rock masses to the surface. The excavated rock mass contains not only ore that can be economically extracted from the face but also waste, which is usually discarded several steps further downstream in the process. As a result, a large amount of rock is transported to the surface, influencing the costs at which the ore is produced. Reducing the amount of waste rock being transported to the surface by introducing a near-to-face sorting plant would improve the in many cases strained transport system in the deep mine. In this study, one of Boliden’s cut-and-fill mines was analysed with respect to the challenges related to rock transportation and increasing mining depth. The study aims to evaluate the potential use of a new near-to-face sorting system in the operating underground mine. Discrete event simulation was used to study and analyse the rock transportation system with and without the near-to-face sorting plant. The paper shows how the underground rock transportation system and the production were influenced when the near-to-face sorting equipment was added into the current system. INTRODUCTION The locations of waste rejection in the mining processes and the cost of removing waste from the system compared with the cost and energy necessary for further comminution are important parts in the material handling system (Bowman and Bearman, 2014). In an underground mine, longer material transportation distances generate the need for further investment in the mobile fleet and ancillary equipment in order to reduce the waste from the material handling as early as possible. One of the ways of reducing the waste (coarse particle size) in material handling is by use of pre-concentration. The benefits of pre-concentration are well known (Schena et al. 1990; Feasby, 1995; Peters et al. 1999; Klein et al. 2002), as well as the factors governing the feasibility of underground pre-concentration (Peters et al., 1999) and the mining integration issues (Klein et al. 2003). In the Onaping Depth orebody in Sudbury, Ontario the study of implementing the pre-concentration resulted in increased capital costs of 6% and a reduction in the operating costs of between 20-40% (Bamber et al, 2004). In this paper, the effects on the production and the transportation system of implementing underground pre-concentration by means of a near-to-face ore sorting plant in the Kristineberg mine are modeled and analyzed using the AutoMod tool. This tool is based on discrete event simulation (DES) (Banks, 2004), allowing high flexibility in customization and enabling the user to view the production of the system before ore sorting plant integration. The sorting plant selected in the simulation is built from modules. The material is fed by conveyor and goes through the comminution, classification, sorting and service processes after which the waste is redirected to backfill headings via trucks. The system mechanically ejects the particles from the feed stream on the basis of the information obtained from both the XRT sensor’s signal and 3D laser scanner based on both density and rate of refraction of light within a particular mineral. The sorting plant could pre-concentrate the metal ore up to 300 mm size. The plant requires little auxiliary infrastructure, is easily modularized for underground installation and can be easily relocated to different areas."

Jan 1, 2016

By G. Hoffman

Sustainable development has brought social, environmental and energy efficiency concerns together with management and governance of natural resources. Cement manufacturing, an energy- and natural resource-intensive industry, is adapting to meet sustainable development goals. Emission standards for cement plants and increasing energy costs have lead to changes in the use of natural resources and recycled materials. Utilizing pozzolans or supplementary cementitious materials (SCMs) as mineral admixtures in blended cement or as a substitute for cement in concrete lowers energy costs and CO2 emissions. Although the western U.S. is rich in natural pozzolans, artificial products, particularly fly ash, have greater use as mineral admixtures. Pozzolans and SCMs have many beneficial properties, such as preventing alkali-silica reactivity, a common problem in the western U.S. Barriers exist for mineral admixtures in the cement and concrete industries because of past inconsistencies in quality or availability. New environmental regulations on the primary industries producing artificial mineral admixtures could adversely affect the quality and quantity of these materials in the future.

Jan 1, 2009

By R. R. Kallu

The current 120 psi seal design and evaluation practices are mostly based on simple analytical solutions. Considering the simplistic assumptions and limitations involved in simple analytical solutions and practical difficulties involved in conducting conventional full-scale explosion tests for evaluating 120 psi seal designs, there is a need for developing new scientific methods and engineering practices for design, analysis and evaluation of mine seals.

Jan 1, 2010

By M. Schlegel, J. A. Villa Mena, R. E. Vivas

ArcelorMittal, headquartered in Luxembourg, is one of the world’s largest steel and mining companies. It supplies steel to industries such as automotive, construction, and energy, with a strong emphasis on sustainability and innovation. The company employs about 125,000 people and, in 2024, produced 42.4 million tons of iron ore and 57.9 million tons of crude steel across 15 countries. Its mining operations span Canada, the United States, Mexico, Brazil, Ukraine, Bosnia and Herzegovina, Kazakhstan, and Liberia, focusing on iron ore and coal extraction to support steel production. This study examines Peña Colorada, one of Mexico’s largest iron ore mines (a joint venture by ArcelorMittal and Ternium). Facing declining ore grades, Peña Colorada adopted Hexagon solutions to uncover and capture project value. A comparison of two Life of Mine (LOM) plans from 2012 and 2016 (before and after implementing Hexagon solutions) shows that between 2019 and 2023, Peña Colorada reduced actual waste by 26% (compared to 2012 LOM) and 19% (compared to 2016 LOM). LOM Plans are generated yearly, and each time, opportunities for reducing mining waste were identified, evaluated and implemented. The key driver was schedule optimization using Hexagon MinePlan Schedule Optimizer (MPSO). This reduction means less waste transported to disposal sites, resulting in fewer hauling equipment operating hours, lower fuel consumption, and reduced carbon emissions.

Feb 22, 2026

By JOHN HOMER, KATHLEEN STABRYLA, JACOB L. CARR, JONATHAN K. HRICA, JENNICA L. BELLANCA

Given the recent focus on powered haulage incidents within the U.S. mining sector, an appraisal of collision avoidance/warning systems (CXSs) through the lens of the research literature is timely. This paper aims to evaluate the maturity of CXS technology through the application of a technology readiness assessment (TRA) to research literature identified by systematic search methods. Results indicate that much of the evidence for CXS performance is at lower levels of maturity: that is, components and prototypes tested in a laboratory and in relevant environments. Less evidence exists for CXS performance at higher levels of maturity — that is, systems evaluated within operational environments — despite the existence of commercial products in the marketplace. This lack of evidence at higher maturity levels within the scientific literature highlights the need for more peer-reviewed research to evaluate CXS technologies. Additionally, results of the review reveal that most of the literature relevant to CXS technologies is focused on vehicle-to-vehicle interactions, which contrasts with haul truck fatal accident statistics that indicate most are due to vehicle-to-environment interactions, such as traveling through a berm. Lastly, the relatively small number and segmented nature of relevant studies suggest there is a need for more incremental research that would better facilitate the improvement of CXS technologies. This progression could be achieved through continued long-term interest and support for CXS technology research.

Mar 1, 2023

By Brenton Fletcher, Yongjun Peng, Wonder Chimonyo

As a cheap, renewable and non-toxic material, starch can contribute to the sustainability of the flotation process, albeit in a minor way as one type of reagent in systems involving materials with far greater impact. But the physical and chemical versatility of starch can help address another issue, namely, that of processing complex ores with decreasing grades of valuable minerals and increasing mixtures of gangue. This paper compares the results of two lab scale flotation studies where starches (native wheat starch (NWS), dextrin and two oxidised wheat starches) were used to depress two common gangue minerals, copper-activated pyrite and carbon (graphite), over a range of dosages. The oxidised starch with the larger molecular weight structures depressed copper-activated pyrite best, and the oxidised starch with lower molecular weight structures was better at depressing graphite. In both cases, the oxidised starches allowed greater recovery of chalcopyrite, pointing to selectivity potential. The extent to which the carbonyl and carboxyl moieties of the oxidised starches contribute to depressant performance is difficult to quantify, but it should not be discounted. Importantly, the results demonstrate relatively simple modifications of native starch by oxidation can yield structures suitable for depressing gangue minerals with diverse surface properties. The challenge remaining for greater application of modified starch depressants is being able to replicate the desired structures at scale in cold-water-soluble form.

Jan 18, 2021

By V. Izaxon

Current practice in mining frozen, underground placers is to support the mine openings by leaving remnant pillars, which are kept frozen to maintain their stability. These pillars may be partially extracted depending on mining conditions, but this practice may be risky, and roof falls are common. Instead of allowing the mined-out areas to cave, the extracted entries could be filled with waste material, which would then be frozen, using cold ventilation air. A finite difference model for analyzing the effects of various parameters on the freezing of backfill in underground mines in the Arctic has been developed and tested. The model also accounts for properties unique to a frozen rock mass, including those that change with temperature. Examination of the characteristics of ice-cemented mining waste materials as backfill indicates that with proper engineering control, a backfill system can be designed for use in production mines. The system will allow increased extraction ratio while maintaining the stability of underground openings with minimum heat impact on the surroundings. These simulated results establish the relationships among the strength, the temperature, and the freezing characteristics of a given material. When coupled with site observations these relationships will facilitate the optimal design of ore pillar recovery methods.

Jan 1, 2004

By Steve Kral

In the United States, the U.S. Environmental Protection Agency (EPA) is set to implement its Tier 2 air quality standards governing high-horsepower, off-road diesel engines. The regulations take effect in January2006. In Europe, similar standards, called Stages, are due to take effect about the same time. And other markets, such as Japan and Australia, have their own standards on tap. Tier 2 standards will further reduce the amount of nitrogen oxide (NOX), sulfur dioxide (SO2), diesel particulate matter (DPM), carbon monoxide (CO) and hydrocarbons off-highway diesel engines are allowed to emit. And even more restrictive Tier 4 standards are due in 2011. The upshot is that operators of high-horsepower engines, particularly in mining, will begin using in their new off-road haul trucks, excavators, shovels and other mining machines diesel engines that are designed to meet these more stringent standards.

Jan 1, 2004

By Dean Workman

Long extensible conveyor systems are an important option for efficient tunnel excavation where intermediate access is impractical. The conveyor system designed for the Pula Subbaiah Veligonda Tunnel #2 in Andhra Pradesh, India will eventually extend to 19.35km. The Ø10.0m water diversion tunnel will be excavated under India?s largest tiger sanctuary using a Robbins Double Shield TBM. Once extended, the conveyor will be one of the longest single-flight systems ever installed in India, and is expected to offer increased system availability over comparable systems using muck cars. This paper will examine the engineering challenges of long-flight extensible conveyor systems in the areas of belt selection, component design, and equipment location in confined assembly and launch areas

By J. K. Pandey, ebashish Mishra, D. P. Mishra, N. K. Mohalik, S. K. Ray

The increasing demand for coal and depletion of shallow depth reserves are pushing towards deeper mining. In deeper coal mines with multiseam workings, the problem of ventilation surges many folds primarily related to air quantity requirement, heat, humidity and spontaneous heating/fire in goaved (gobbed) out areas. The paper describes the design of a new approach to improve the ventilation system of a real-life deep underground coal mine with multiseam workings. For this, the ventilation problem of one deep underground coal mine 6&7 pits Bhutgoria Amalgamated Colliery of Tata Steel Ltd. with multiseam workings has been studied in detail to determine an appropriate solution. A ventilation survey of the mine and computer simulation of the ventilation network has been carried out to reach a practical solution. Ventilation survey results have been analysed to develop a representative ventilation network of the mine for both qualitative and quantitative analysis. Further, computer simulation of the ventilation network of the mine has been performed to virtually verify the application of a highcapacity booster fan in the present ventilation circuit without disturbing the vulnerable areas. Field validation is also carried out after the implementation of the solution in the mine to determine its efficacy. Thus, the findings of this paper can be directly applied for the installation of booster fans to achieve the required air quantity in deep underground coal mines with multiseam workings having spontaneous combustion liabilities of upper seam goaved out areas.

Jun 2, 2022

By Hengwei Yan, Zhanwei Liu, Wenhui Ma, Ping Xiong

The sulfur in high-sulfur bauxite not only pollutes the environment but also harms alumina production. This study investigated the removal of sulfur from high-sulfur bauxite by adding Zn or ZnO during the Bayer process. The results showed that the different valence sulfur (S2−, S2O3 2−, SO3 2−, and SO4 2−) in sodium aluminate solution can be effectively removed by adding Zn during the digestion process. Adding ZnO removes the S2− in liquor, but the other sulfur compounds (S2O3 2−, SO3 2−, and SO4 2−) are not affected. The mechanism of sulfur removal has been elucidated, where the S2O3 2−, SO3 2−, and SO4 2− are first reduced to S2−, and after adding Zn, the S2− enters into red mud in the form of ZnS. The ZnO then reacts with S2− to generate the ZnS that enters into red mud. Thus, this is a new and effective method of sulfur removal by adding Zn during the digestion process. The results shed light on the removal of sulfur from high-sulfur bauxite during alumina production.

Jun 24, 2020

By Lewis V. Wade

This paper summarizes the results of the rock mechanics monitoring program performed as part of Old Ben Coal Company's longwall coal mining demonstration project conducted in cooperation with the United States Bureau of Mines. The work described herein included installation of instruments, collection of data and data analysis performed during mining of the first longwall panel in Mine No. 24. The rock mechanics monitoring program included both surface and underground instrumentation and was designed to achieve the following purposes: 1 -To provide the capability to observe unusual situations during mining so that remedial measures could be instituted quickly 2 -To formulate design guidelines for future longwall mining efforts; 3 -To evaluate surface subsidence, and its character, rate and potential effects on cultural features, and to develop criteria to assist in predicting subsidence for other mines having similar roof conditions. Six previous attempts with longwall methods in Old Ben Coal Company's Hine 21 had been unsuccessful due to roof control problems. A description of these attempts is given by Moroni (1973). In preparation for the present longwall operation a study was performed to review existing data on the previous unsuccessful attempts, to establish coa1-and floor-strata bearing capacities in Mines Nos. 21 and

Jan 1, 1977

By Jose A. Delgadillo

The hydrocyclone problem has been a challenging task for the last 30 years. In the 80’s and 90’s Computational Fluid Dynamics solution to this problem began to appear. These were unsuccessful due to over simplification. In the past 3 dimensional solution with ?-e model and Reynolds Stress Model have been published. In this paper RSM and ?-e models are compared with velocity profiles measured in 75 mm and 250 mm diameter hydrocyclones. It is shown that results are not satisfactory with RSM or ?-e and that a model called Large Eddy Simulation is needed to describe velocity profile evolution and size classification.

Jan 1, 2005

By David A. Zegeer

Since 1980, more than 40 miners have lost their lives by being trapped and suffocating in stock-piles, bins, silos, and similar facilities. Mine Safety and Health Administration (MSHA) is concerned about these accidents, most of which could be prevented if management and miners appreciated the hazard. In February 1986, the coal industry had a suffocation accident that drew national attention. A group of engineers were standing on a coal stockpile. It gave way under their feet. Five of the engineers were buried in the coal and suffocated. As with all fatal accidents, MSHA investigated the cause of this tragedy. I also asked my staff to look into the history of similar accidents. I found out it is rare to have multiple fatalities due to suffocation in material. But, over the years, there has been a long series of individual fatalities from this type of accident. Here are some examples. In Oct. 1985, a coal mine employee in Virginia entered a hopper to collect a coal sample. The feeders were started while he was standing in the hopper. He sank into the coal and suffocated. In Sept. 1985, an employee at a Texas sand company climbed onto a surge pile, to check a problem with sand flow. When other employees found him, the sand had swallowed him. Only his face and one hand were showing. Though the victim's face was clear of the sand, he suffocated before rescuers could free him. Many people do not realize you can suffocate in this kind of situation, though your head is free. Every time you exhale, the material has room to shift and press harder against your chest. Then you have less room to inhale. If this goes on long enough, it gets to the point where you cannot inhale at all. That is what happened to the victim in this accident. In May 1985, a plant operator at a Wisconsin sand and gravel operation purposely slid into the drawhole of a surge pile. He tried to break up large rocks that were clogging the drawpoint. Material piled on the side of the surge pile slid down and buried him. The operator was wearing a safety belt and line. But he was covered by 3 to 3.7 m (10 to 12 ft) of material and could not be pulled free. This incident illustrates another point. A safety line can help. But it is not enough. Workers should never put themselves in a position where loose material can fall on them from above. In Jan. 1985, a young Utah coal miner was waiting for a ride home from a co-worker whose job was at the tipple. A jam developed in the coal bin. The men could not clear the jam from the outside. So the young miner jumped into the bin. He started digging with a shovel at the toe of the coal pile. It caved in on him and he suffocated. The young miner had only three months of mining experience. He had not been trained for work around the coal bin. Since 1980, 16 coal miners and 26 nonmetal miners have lost their lives in loose-material suffocation accidents. Suffocation accidents occur in many areas around mines - bins, hoppers, stockpiles, surge piles, and silos, among others. One recent accident occurred at a surface coal mine in Illinois. The victim was walking over an area that had been drilled and blasted the week before. He fell into a void that had been crusted over with earth. He too suffocated. And many materials have been involved in suffocation accidentscoal, crushed stone, sand, salt, different kinds of ore, ammonium nitrate pellets used in blasting, and a powdery byproduct of iron ore milling called calcine. In addition to fatal accidents, there are near misses. We do not know how many. Most of them are not reported. A person who gets trapped in material, but is rescued, is usually unhurt. MSHA sometimes hears about these accidents by chance, or because they are reported in the local media. We do know that near misses are happening far more often

Jan 1, 1987