Search Documents

By Z-P. Song, Z-B. Jiang, A-N. Jiang

"In deep excavations under conditions of high ground stress, even hard rock undergoes creep and other time-dependent effects that may result in instability. This study involves an analysis of the typical damage to the surrounding rock in the deep tunnels of the Jinchuan nickel mine in China. In order to understand the creep mechanism, triaxial creep laboratory tests were conducted under high stress. The creep characteristic curves and the Nishihara model parameters of typical rock were obtained from these tests. The numerical simulations, with which the creep model is developed, were performed using Flac3D. The creep model parameters were back-analysed on the basis of field monitoring data. Finally, appropriate support schemes for deep tunnels are suggested. The creep deformation of rock increases with time and axial load. At the same load level, the creep deformation of unloading is greater than that of loading. The simulated deformations of the surrounding rock are coincident with those from in situ monitoring, indicating the applicability of the presented rock creep model in situations of high ground stress. The results constitute a reference for support design in deep mining tunnels.IntroductionThe excavation of underground caverns can alter the natural stress field of the surrounding rock. In deep engineering projects under conditions of high ground stress, even hard rock shows obvious creep properties and time effects (Yao, 2005; Liu, 1994). The time effect of excavation not only causes decompression of the floor and increases sidewall stress, but also leads to stress concentration at the corners of the excavation, which influences the stability of the surrounding rock in a very complex manner.Many researchers have studied the creep properties of rock. ‘Griggs (1939) showed that creep occurs in sandstone, shale, and silty sandstone rock under the load of 12.5%–80% of the failure load.’ Subsequently, much research has been published on rock creep tests, including the uniaxial compressive creep test, the triaxial compressive creep test, the discontinuity rock shearing test, and field tests (Wawersik, 1974; Amadei et al., 1980; Okubo et al., 1991; Jin et al.,1995). A rheological model is used to describe the complex rheological deformation of material. This model is based on various fundamental parameters including rock elasticity, plasticity, and viscous properties, which can be combined into a constitutive model to reflect the rheological properties of various types of rocks. Wang et al. (2014) studied the creep– damage–rupture characteristics of rock salt by applying a creep-damage model. Munson (1997) developed a multi-mechanism constitutive model of creep of polycrystalline rock salt based on steady-state creep and modified it to incorporate transient creep through work hardening and recovery. An elasto-viscoplastic approach was developed to simulate the timedependent nature of the fracture zone (Malan, 1999). Rheological models were proposed to understand the collapse of iron ore mines in Lorraine by Dragan et al. (2003)."

Jan 1, 2016

By A. Hinde, M. Moys, L. C. Woollacott

The material-balance smoothing technique is applied directly to the problems associated with the evaluation of the performance of backfill-preparation plants. A computer package specially designed to assist the process engineer in such evaluations has been developed. The usefulness of the technique as compared with other methods for the extraction of meaningful information from backfill-plant data is demonstrated.

Jan 1, 1992

By A. K. K. Rompel, G. K. Chunnett

Introduction Structure appears to be of secondary importance to the Bushveld Complex when viewed from a distance. However, a closer look already reveals that large fault zones bound the Bushveld Complex. These fault zones are deep-seated crustal lineaments of continental magnitude such as the Thabazimbi-Murchison Lineament, the Johannesburg-Barberton Lineament, the Palala Fault zone and the Rustenburg fault. Furthermore, the Bushveld Complex is transected by large faults such as the Vlakfontein Fault, visible in the Pilanesberg, the Steelport Fault and the Laersdfrift Fault in the Eastern Bushveld, the Brits Graben, and a multitude of dyke generations (Figure 1). When pursuing structures on a project scale, the lack of outcrop, particularly in the western part of the Bushveld, is of no help for the exploration geologist. Consequently, the first dataset that needs to be considered is the Landsatimagery. Older Landsat TM 5 or newer Landsat ETM 7 will immediately reveal areas of outcrop for field visits, and, after further processing, indicate the geological units, in particular the platiniferous Critical and the Main Zone of the Rustenburg Layered Suite (Figure 2). Airborne magnetic surveys are the subsequent dataset necessary for any decent interpretation of the geology under the ?Black Turf? cover. Currently Anglo Platinum acquires aeromagnetic surveys with a flight height of 20 m and a line spacing of 50 m. These result in high-resolution imagery absolutely crucial for dyke delineation and dip modelling, stratigraphic layer detection, IRUP detection and possibly pothole discovery and fault delineation (Figures 3 and 4). However, the aeromagnetic surveys and the Landsat imagery reveal structures very much confined to the surface and may be hundreds of metres above the platiniferous reef horizons. This may lead to inaccuracies. When determining the underground structures for shaft sinking and mine planning, a 3D seismic survey is advisable. Too many shafts have been sunk in the Witwatersrand Basin for gold and in the Bushveld for platinum without sufficient information of the structure beneath. Recent 3D seismic surveys in the Bushveld have proven the technology and visualized the reef horizons and led to an interpretation of the underground structure (Figures 5 and 6). [ ]

Jan 1, 2004

COUNCIL AND STANDING COMMITTEES, 1974-1975 Office Bearers : Prof. R. P. Plewman (President), Dr R. E. Robinson and Dr M. D. G. Salamon (Vice Presidents), J. K. E. Douglas (Honorary Treasurer), and P. W. J. van Rensburg (Immediate Past President). Elected Members of Council: Dr M. G. Atmore, E. Collier, G. H. Grange, Dr P. R. Jochens, Dr D. I. Legge, D. G. Malan, C. T. Shaw, L. W. P. van den Bosch, D. A. Viljoen, H. M. Wells, P. A. von Wielligh. Branch Chairmen: B. T. Hosking (Witbank-Middelburg Branch), D. A. Smith (Orange Free State Branch). Past Presidents Serving on Council: R. J. Adamson, M. Barcza (until May 1975), H. Britten, H. E. Cross, Prof. J. de V. Lambrechts (until December 1974), R. C. J. Goode, Prof. D. D. Howat, Dr J. P. Hugo, D. M. Jamieson, D. G. Maxwell, Dr J. T. McIntyre, V. C. Robinson. Ten Council meetings were held during the year, with an average attendance of 19, and the standing and sub-committees held 74 meetings. COMMITTEE CHAIRMEN Membership, Dr M. D. G. Salamon; Technical Programme-Metallurgy, D. A. Viljoen; Technical Programme-Mining, G. H. Grange ; Vacation School-Metallurgy, Dr P. R. Jochens; Vacation School-Mining, Dr M. D. G. Salamon; Awards, Prof. R. P. Plewman; Excursions, Dr D. I. Legge; Constitution, Rules and Policy, P. W. J. van Rensburg and Prof. R. P. Plewman; Mines and Works, P. A. von Wielligh; Education, P. W. J. van Rensburg. REPRESENTATIVES ON OTHER BODIES Associated Scientific and Technical Societies Members: V. C. Robinson and Prof. R. P. Plewman. Alternates : Dr R. E. Robinson and Dr M. D. G. Salamon. Federation of Societies of Professional Engineers Members : J. K. E. Douglas and P. W. J. van Rensburg. Alternates : Prof. R. P. Plewman and G. H. Grange. South African Council for Professional Engineers Member : R. C. J. Goode. Alternate : G. H. Grange. Engineers' Liaison Committee (Pretoria) Member: Dr J. P. Hugo. Alternate: P. W. J. van Rensburg. MEMBERSHIP Thirteen Fellows, seventeen Members, eleven Graduates, three Associate Members, eighteen Associ¬ates, twenty-six Students, and one Company Affiliate were elected during the year. Nine Fellows, four Members, and three Associates were admitted to retired membership. Eight Fellows were elected to Honorary Life Membership. Three Members and one Graduate were transferred to Fellows, nine Graduates and two Students to Members, six Students to Graduates, one Student to Associate, and one Associate to Associate Member. Six Fellows, ten Members, three Associates, and one Student resigned. A statement of membership as at June 30th 1975 and the end of the previous year is shown in the following tabulation: 30th - 30th June, - June, 1974 - 1975 Honorary Life Fellows - 9 - 15 Honorary Fellows 8 - 8 Life Fellows 170 - 170 Fellows 544 - 536 Members 512 - 523 Associate Members 10 -15 Graduates 130 - 133 Associates 194 - 210 Students 173 -175 Company Affiliates 70 - 71 1 820 - 1 851 [ ] OBITUARIES Your Council records with deep regret the death during the year of the following members: M. Barcza, Honorary Life Fellow and Past President of the Institute; J. A. Boyd, F. E. Keep and J. H. Taylor, Life Fellows; I. D. B. Corner, C. O'G. Deane, R. E. Gilmour, A. C. Hofmeyr, M. W. Howell, T. J. Robin and F. C. Steinhobel, Fellows; J. J. Frankel, Member; T. J. Higgs, Associate. FINANCE The annual accounts, which follow this report, indicate that income again exceeded expenditure by a margin of R21 410 (last year R28 524). This year's income of R71 184 showed a further increase compared with last year's figure of R55 025. Costs, however, also in¬creased, and it is calculated that, excluding non-recurrent costs, the cost of running the Institute in¬creased by R6 654 from R25 501 to R33 155 for the current year. The main increases were involved in secretarial fees, stationery and print¬ing, and in publication of the Journal. All indications are that costs will continue to rise, and we have been advised that the A.S. & T.S. will be increasing their secretarial fees by 25 per cent in the year ahead to meet their rising costs. This year's surplus was derived entirely from the revenue from sales of publications (R13 644) and a surplus from the 1974 Winter School (RIO 654). There can be no certainty that revenue from these sources can be repeated each year. Our funds are in a satisfactory position because of these worth¬while activities, but the administrat¬ion of the Institute should not de¬pend on them. Council will accord¬ingly have to give consideration in the year ahead to an upward adjust¬ment of subscriptions to meet rising costs.

Jan 10, 1975

By C. -I. Lee

Since the early 1970s, Korea has constructed many large-scale tunnels and underground storage caverns in response to the rapid industrial development. The rock mechanics engineers have accumulated valuable experiences in the area of underground space technologies. But they still face technical challenges in environmental and safety aspects. To discuss those challenges in Korea, a brief engineering description of underground space projects including oil and gas storage, food storage, pumped storage power plant, transportation tunnels, waterway tunnels, and radioactive waste disposal is presented. Mechanical and hydrological stability analyses of the storage caverns in Korea are also introduced. Depuis le début des années soixante-dix, le développement industriel rapide en Corée a entraîné la construction de nombreuses galeries et cavernes de stockage souterraines. Les ingénieurs de mécanique minière ont donc accumulé des expériences précieuses dans le domaine de la technologie de l’espace souterrain. Cependant, ils font toujours face à de nombreux défis techniques en ce qui concerne les aspects de l’environnement et de la sécurité. Pour présenter ces défis en Corée, l’étude présente décrit les projets d’espace souterrain, y compris le stockage de pétrole et de gaz, de nourriture, centrales de stockage pompé, tunnels de transport, tunnels navigables, et évacuation des déchets radioactifs. Des analyses de stabilité mécanique et hydrologique des cavernes de stockage en Corée sont aussi présentées. Seit Anfang der 70er-Jahre, baute Korea in Folge raschen Industriewachstums viele lange Tunnelsund unterirdische Lagerungsräume. Fachkräfte im Bereich Gesteinsmechanik sammeltenwertvolle Erfahrungen über unterirdische Raumtechnologien. Dennoch stehen sie auch heute nochvor technischen Herausforderungen im Bereich Umweltschutz und Sicherheit. Zur Erläuterungdieser Herausforderungen in Korea folgt eine kurze technische Beschreibung der Projekte zurSchaffung unterirdischen Raumes für beispielsweise Öl- und Gaslagerung,Nahrungsmittellagerung, Pumpspeicherwerke, Straßen- und Wasserstraßentunnels, als auchLagerung radioaktiven Mülls. Mechanische und hydrologische Stabilitätsanalysen derLagerungsräume in Korea werden ebenfalls dargestellt.

Jan 1, 2003

COUNCIL AND STANDING COMMITTEES - 1973-1974 Office Bearers: P. W. J. van Rensburg (President), Professor R. P. Plewman and Dr R. E. Robinson (Vice Presidents), J. K. E. Douglas (Honorary Treasurer), and Dr J. P. Hugo (Immediate Past President). Elected Members of Council: Dr M. G. Atmore, G. H. Grange, Dr P. R. Jochens, J. G. Kirchner, Dr D. I. Legge, W. W. Malan, Dr M. D. G. Salamon, L. W. P. van den Bosch, D. A. Viljoen, P. A. von Wielligh. Branch Chairmen: B. T. Hosking (Witbank-Middelburg Branch), E. T. Wilson (Orange Free State Branch). Past Presidents Serving on Council: R. J. Adamson, M. Barcza, H. Britten, H. E. Cross, Professor J. de V. Lambrechts, R. C. J. Goode, Professor D. D. Howat, D. M. Jamieson, D. G. Maxwell, Dr J. T. McIntyre, V. C. Robinson. Ten Council meetings were held during the year, with an average attendance of 19, and the standing committees held 30 meetings. COMMITTEE CHAIRMEN Membership, Dr R. E. Robinson ; Metallurgical Colloquia, Dr R. E. Robinson ; Mining Colloquia, L. W. P. van den Bosch; Awards, P. W. J. van Rensburg; Excursions, P. A. von Wielligh; Dinner, G. H. Grange ; Constitution, Rules and Policy, Dr J. P. Hugo; Adjudicating, P. W. J. van Rensburg; Mines and Works, W. W. Malan; Education, Dr J. P. Hugo. REPRESENTATIVES ON OTHER BODIES Associated Scientific and Technical Societies: Members : V. C. Robinson and D. G. Maxwell Alternates : P. W. J. van Rensburg and Dr J. P. Hugo. Federation of Societies of Professional Engineers Members : J. K. E. Douglas and P. W. J. van Rensburg Alternates : Dr J. P. Hugo and G. H. Grange. South African Council for Professional Engineers Members : R. C. J. Goode and J. K. E. Douglas Alternates: G. H. Grange and Dr R. E. Robinson. Engineers' Liaison Committee (Pretoria): Member: Professor J. de V. Lambrechts Alternate : Dr J. P. Hugo. MEMBERSHIP Seventeen Fellows and Members, twenty-three Graduates, ten Associate Members, twenty-two Associates, thirty-four Students, and seven Company Affiliates were elected during the year. Eleven Fellows and four Members were admitted to retired membership. Five Fellows were elected to Honorary Life Membership. Four Members, two Graduates, and one Student were transferred to Fellows ; eleven Graduates and Students were transferred to Members ; eight Students to Graduates; and four Students to Associates. A statement of membership as at June 30th 1974 and the end of the previous year is given in the following tabulation 30th - 30th June, - June, 1973 - 1974 Honorary Life Fellows 4 - 9 Honorary Fellows 9 - 8 Life Fellows 177 - 170 Fellows 536 - 544 Members 487 - 512 Associate Members - - 10 Graduates 128 - 130 Associates 186 - 194 Students 183 - 173 Company Affiliates 64 - 70 1 774 - 1 820 OBITUARIES Your Council records with deep regret the death during the year of the following members : Dr P. N. Lategan and Dr O. A. Jackson, Honorary Life Fellows and Past Presidents; C. Airth, T. L. Blunt, J. B. Dennison, A. E. Frazer, C. L. Lamb, V. O. Reid, K. Richardson and D. G. Roberts, Life Fellows ; H. F. Allan, J. T. Beaumont, M. Eisenstein, J. C. Hall, C. F. Louw, H. H. McGregor, R. Murchison, and J. E. Williamson, Fellows; and R. B. Miles, Associate. FINANCE The annual accounts, which follow this report, reflect a healthy position and show that measures taken by Council over the last few years to boost income have been successful. A higher income was needed not only to meet rising costs but also so that the services provided by the Institute for its members could be expanded. This year's income of R55 025 showed a further increase compared with last year's figure of R48 307. Income from subscriptions was higher mainly owing to an increased number of Company Affiliates, and this is indicative of the support given by mining and metallurgical companies to the good work being done by the Institute. Further sales of publications of the symposia held over the last few years again made a useful contribution to income of R4560. The first Winter School held in 1973 yielded a surplus of R7495 after the expenses had been deducted from the income received from registration fees. The cost of administering the Institute increased by R2212 compared with the previous year. Included in this was a donation of R1000 to the A.S. & T.S. Trust Fund. The cost of publishing and printing the Journal increased by R2034, but advertising and extraneous sales of the Journal were higher, with the result that the net cost of the

Jan 10, 1974

By R. H. Matjie, J. R. Bunt, C. A. Strydom

"A number of conventional and advanced analytical techniques (proximate and ultimate analysis, low-temperature oxygen-plasma ashing, X-ray diffraction, X-ray fluorescence spectrometry, coal petrography, and lightelement electron microprobe analysis) have been integrated and crosschecked to provide detailed characterization of coals from the Highveld coalfield in South Africa, as a basis for better understanding of the mineralogical and chemical properties of the individual coal sources that are blended as feedstocks for combustion and carbon conversion processes. The techniques included methods to quantify the abundance and composition of the mineral matter (minerals and non-mineral inorganic elements), and also the abundance and chemical composition of the individual macerals in the individual coals concerned.Kaolinite is the most abundant of the minerals in the coals studied, with lesser but still significant proportions of quartz, mica and/or illite, dolomite, calcite, and pyrite. Small but variable proportions of anatase, goyazite, and siderite are present in some coal samples. Electron microprobe analysis, based on a special configuration for light-element study, shows that the vitrinite contains less carbon and more oxygen, and has significantly higher concentrations of nitrogen and organic sulphur, than the inertinite macerals in the same samples. Minor proportions of organically-associated inorganic elements, including titanium, were also identified in some of the maceral components.A comprehensive knowledge of the minerals and non-mineral inorganic elements in the coals used for feedstock preparation, obtained by integration of data from these advanced analytical techniques with more conventional analyses, may be of benefit in understanding the processes that take place during coal utilization, and also in avoiding or ameliorating some of the operational and environmental problems that may occur in different sectors of the coal utilization industry."

Jan 1, 2016

By R. J. Davidson, B. Strong

The piloting and eventual large-scale operation of fixed-bed carbon columns for the recovery of gold from plant effluents is described. A fixed-bed carbon pilot plant comprising three adsorption columns was used for the recovery of gold from clarified plant effluent at the Vaal Reefs Exploration and Mining Company (West Division). The effluent ,which contained 0,1 toO,S g/t of gold and less than 10 g/t of free cyanide, was adjusted to pH 8 prior to use. Daily acid treatment of the carbon circuit with 3 per cent hydrochloric acid was shown to have a most significant effect on increasing the gold adsorption. The acid treatment involved a plant downtime of only I to 2 minutes per day. High loadings of gold (up to 30 k g/t) and copper (up to 75 k g/t) were obtained on the leading column, while the gold recoveries averaged 98 per cent over 17 weeks of continuous operation. The subsequent elution of loaded carbon in a pilot elution column indicated the use of abnormally high amounts of the pretreatment reagent (caustic soda and cyanide) used in gold elution. This was attributed to the high loading of copper on the carbon. However, the elution of both the gold and the copper at 110°C with demineralized water as the eluant was satisfactory. In a similar large-scale operation, three fixed-bed carbon columns each containing 4,5 t of carbon were used to treat 80 to 120 t/h of plant effluent with a gold concentration of about 0,15 g/t. Gold loadings of 5 to 6 k g/t were obtained regularly, while the gold recovery averaged 97 per cent over a 12-month period. The capital cost of the plant was recovered in 2 to 3 months. The evidence presented strongly suggests that copper plays a significant role in the adsorption and elution of gold under the prescribed conditions, and in the subsequent precipitation of gold following acidification of the eluates. The formation of a highly insoluble gold-copper complex produced under acid conditions appears to explain many of the observations made in the investigation.

Jan 1, 1983

By R. Singh, A. K. Dhawan, M. Dixit, H. Dev

ABSTRACT: The modulus of deformation of rock mass is an important engineering parameter required for the design of foundation of hydraulic structure and to study the interaction of rock mass and the structure at the foundation support. Different equipment and techniques are used to arrive at the design modulus value. Since any error in the estimation of modulus values results in multiplication of its effects in the analysis, it is necessary to know about the reliability of testing equipment and procedures. In the present study modulus values obtained by different in-situ equipment at different project sites have been compared. KURZFASSUNG: Der Verformungsmodul von der Felsenmasse ist technisch ein wichtiger Parameter, den man zur Konstuktion des Grunds fuer die Hydro – Tektonik, benoetigt um auch die gegenseitige Beeinflussung der Felsenmasse und der Tektonik am Traggrund zu betrachten. Verschiedene Geraete und Methoden werden angewandt, um den Ausfuehrungsmodul -Wert zu erreichen. Es ist erforderlich, die Zuverlaessigkeit der Pruefeinrichtung sowie des Verfahrens zu kennen, da irgend ein Fehler in der Abschaetzung von Modulwerten in der Analyse zu einer Vervielfachung ihrer Einwirkung fuehrt. In der vorligenden Arbeit werden die Modulwerte gewonnen aus unterschiedlichen Einrichtungen an Ort und Stelle and verschiedenen Projekt -Stellen mit einander verglichen. SOMMAIRE: Le module de deformation d’une roche est un parametre important pour la conception et realisation des ouvrages hydrauliques ainsi que pour etudier l’interaction de la roche et de la structure d’appuis de base. De divers equipments et techniques sont employes pour determiner la valeur de ce module de conception. Puisque l’effet d’une erreur d’evaluation du module devient multiplie dans l’analyse, il est necessaire de savoir la fiabilite des equipments et des methods qu’on ulilise. Dans cette etude, on a compare les valeurs des modules obtenues en employant les equipments in-situ aux sites differents de projets.

Jan 1, 2003

1. Book review Respiratory protection - principles and applications by B. Ballantyne and P. H. Schwa be (Editors). London, Chapman Hall, 1981. (Reviewer: M. J. Martinson) 2. New manual Swedish steel manual, 1981. Available from Jernkontoret, P.O. Box 1721, S-I11 87 Stockholm, Sweden. SEK 85. 3. Publications of the Mineral Policy and Energy Sectors, Canada General review by L. Tibbo. 10 pp. Columbium (niobium) and tantalum by D. G. Fong. 6 pp. Sulphur by B. W. Boyd. 13 pp. Statistical summary of the mineral industry in Canada. 66 tables. Uranium by R. M. Williams. 16 pp. 4. Mintek reports Report 2126 The determination, by microwave techniques, of the interface between pulp and froth. Report 2129 An electrode controller for submerged-arc furnaces. Report 2131 The separation of trace elements in manganese dioxide. Report 2132 The assessment of pellicular anion-exchange resins for the determination of anions by ion chromatography. Report M2 The preparation of two reference materials of South African fluorspar. Report M3 The platinum-group minerals in the UG-2 Layer of the Bushveld Complex at Maandagshoek 254KT.

Jan 1, 1982

By P. Saari

The Talvivaara deposits are located in Eastern Finland, within the Kainuu Schist Belt. These polymetallic sulphide deposits are of relatively low grade, but bioheapleaching enables economically profitable nickel extraction from the ore. Zinc, cobalt, and copper are also produced. Talvivaara?s production process begins with large-scale open-pit mining and four crushing stages, followed by stacking of the ore in bioleaching heaps. The ore is first leached for 13?14 months on the primary leach pad, after which the leached ore is reclaimed, conveyed, and re-stacked on the secondary heap pad. After secondary leaching, the barren ore will remain on the secondary heaps permanently. In the metals recovery process, the metals are precipitated from the pregnant leaching solution. Construction of the process was begun in spring of 2007 and first metal sulphides were produced at the plant in October 2008. The development of the bioheapleaching process was begun in a 17 000t on-site pilot heap operated during 2005?2008 and has continued in the industrial heap. At industrial scale, the development measures have focused on improving the permeability and aeration of the heap. Challenges with crushing and aerations systems at the beginning of industrial-scale leaching delayed the increase in metal recovery, but after the first two operational years the leaching results have improved significantly and the process is performing as targeted.

Jan 1, 2012

By P. Lundman, L. Rosengren, T. Brandshaug

Tunnel 99’, the Swedish National Road Administration´s (SNRA) general technical specification for road tunnels requires that the load bearing system must be designed to withstand specified design explosion loads. This paper presents the results of an SNRA study to provide a perspective of design analyses tailored to comply with the new requirement. The paper provides an example of a design analysis for assumed tunnel conditions using a numerical model. Dynamic predictions of potential damage to the rock mass and ground support system (rock bolts and shotcrete) from the specified explosion loads are presented including the nonlinear response of the shotcrete. “Tunnel 99”, qui fixe les règles de l’Administration nationale suédoise des Routes (Vägverket) concernant la conception et la construction des tunnels routiers, requiert entre autres que la structure porteuse soit capable de résister à certaines contraintes spécifiques résultant d’explosions. Cette étude présente les résultats d’une étude effectuée par Vägverket en vue d’obtenir une perspective d’analyses de conception spécialement élaborées pour se conformer aux nouvelles règles. Il contient un exemple d’analyse en fonction de conditions déterminées, basée sur un modèle numérique. Des prévisions de’études dynamiques de dommages potentiels subis par la masse rocheuse et les systèmes de soutènement (boulons d’ancrage et béton projeté) du fait des contraintes libérées par la force d’explosion spécifiée sont également présentées, y compris dans le cas d’une réaction non linéaire du revêtement en béton. “Tunnel 99” - die Vorschriften für Strassentunnel der Nationalen Schwedischen Behörde für Straßenwesen - (Vägverket) - fordern vom Tragsystem eine Auslegung in der Form, dass es spezifischen Explosionsbelastungen standhält. Dieser Artikel präsentiert die Ergebnisse einer Studie der Behörde, um einen Ausblick über konstruktive Auslegungen zu geben, die geeignet sind, die neuen Vorschriften zu erfüllen. Der Artikel zeigt ein Beispiel einer konstruktive Auslegung für eine angenommene Tunnelsituation mit Hilfe eines numerischen Modells. Voraussagen unter Beachtung der vollständigen dynamischen Berechnung zu potentiellen Schädigungen des Gebirges und des Ausbaus (Anker und Spritzbetonauskleidung) durch die spezifizierten Explosionsbelastungen, einschließlich des nichtlinearen Verhaltens der Spritzbetonauskleidung, werden gezeigt.

Jan 1, 2003

By F. P. A. Robinson, J. W. Fourie

Austenitic stainless steels are welded using low-heat inputs. However, owing to differences in the physical metallurgy of austenitic stainless steels and duplex stainless steels, low-heat inputs should be avoided for duplex stainless steels. This paper highlights the differences in solidification mode and transformation characteristics of these two types of alloys. Recent work on the effect of heat input on the properties of weldments of duplex stainless steels is reviewed.

Jan 1, 1990

By M. H. Marsden, R. A. Laybourne, J. D. Flint

Operations of the strip mine at Arnot Colliery are described, and the improved volumetric extraction of the in situ coal reserves that has been obtained by the application of strip-mining techniques is highlighted. An account is given of the major problems encountered during the early stages of the operation with particular reference to overburden removal. coal and parting handling, and transportation. The techniques used in dealing with the problems and the current degree of success in overcoming them are outlined.

Jan 1, 1980

By Z-B. Cheng, X-J. Liu

"Intensive mining of shallow coal seams tends to result in severe subsidence of the ground surface. Surface subsidence is a complex dynamic spatiotemporal process that constantly changes as mining advances. With Liangshuijing coal mine as a case study, 3DEC numerical software was used to simulate the development of the moving subsidence field from open-off cut to full subsidence on the working face. The results demonstrate that the formation of a subsidence field is directly related to the coal seam depth H and the extent of the mine workings. Taking the advance distance of the working face as the unit of scale, the process of surface subsidence can be divided into four stages: micro-change (H/ p), the development of surface subsidence (2H/ p), the formation of a movement subsidence field (3H/ p), and dynamic balance (4H/ p). The changing movement of a subsidence field can be fully described by the characteristics of surface subsidence value, curve slope, and the inflection position. The results provide important technical support for predicting surface subsidence and the temporal–spatial evolution features of mining subsidence. IntroductionChina’s coal output was about 3.52 Gt in 2017 (China National Coal Association, 2018), making it the largest coal producer in the world, accounting for almost half of total world coal production. Coal production and distribution play a vital role in the energy industry of China. However, entire overlying strata, from coal seam to surface, are disturbed as a result of long-term, high-intensity and large-scale mining, causing surface subsidence. This results in groundwater loss, surface desertification, vegetation loss, and mud-rock flows. These issues have become topics of common concern throughout society. According to related research results (Liu 2008), the area of surface subsidence caused by coal mining in China has reached about 600 000 ha, some 0.2 ha (and up to 0.42 ha) of surface subsidence for every 10 000 t of coal produced. Surface subsidence disasters not only damage buildings, water conservancy, transportation infrastructure, and farmland, but also cause adverse effects on individual and community lifestyles, environmental hygiene, and economic development. Deterioration of the ecological environment in mining areas has a long history and is very harmful (Lu, 2015)."

Feb 1, 2019

By T. F. Muller

In recent years, a great deal has been written and spoken, both in our country and overseas, about the dangers posed to the environment and the ecology by mining operations. The object of this address is to put this problem, and it is a real problem, into reasonable perspective. I shall try to present the various facets that merit consideration as objectively as possible. In doing so, I shall examine the following factors: Book review National Coal Board. Gate belt conveyors. London, H.M.S.O. (Price 95p.) Although the preface of this handy little book states that it has been written for the guidance of miningoperation trainees, it will prove valuable to the practising engineer as well. NIM reports Report no. 1733 A mineralogical investigation of weathered carbonatite from Salpeterkop. (14th Apr., 1975; re-issued 28th Feb., 1978). Report no. 1823 The recovery of gold and pyrite from a residue dump at Crown Mines. (10th Jul., 1976; re-issued 28th Feb., 1976). Report no. 1829 An investigation of weathered carbonatite from Salpeterkop. (20th Jul., 1976; reissued 28th Feb., 1978). Report no. 1932 A BASIC computer programme for the evaluation of intensity data from the Telsec Lab-X-250 Analyser. (12th Jan., 1978). Report no. 1940 The extraction of the noble metals with n-octylaniline, and its application to the analysis of platinum-bearing materials. (30th Jan., 1978). Report no. 1945 Analyses of the NIMROC reference samples for minor and trace elements. (28th Feb., 1978). Report no. 1945 Analyses of the NIMROC reference samples for minor and trace elements. (28th Feb., 1978). International futures conference A conference entitled 'The Road Ahead' is being organized by the 1820 Settlers National Monument Foundation to be held in Grahamstown from 3rd to 7th July, 1978. Conference of metallurgists The technical programme has been established for the 17th Annual Conference of Metallurgists sponsored by the Metallurgical Society of the Canadian Institute of Mining and Metallurgy. This year the Conference will be held in Montreal, Quebec, on 27th to 31st August, 1978, together with the 8th Hydrometallurgy Meeting.

Jan 1, 1978

By M. B. Díaz Aguado, I. Á. Fernández, C. González Nicieza, B. S. Menéndez

This paper summarizes the works that the Research “Group of Ground Engineering”, belonging to the Mining Department of the University of Oviedo, Spain, has been developing in close cooperation with the Regional Mining Department, since 2001, in order to control and monitor an experimental underground limestone exploitation by the room and pillars method. The aim of the current research is not only the geotechnical characterization of the rock mass (by means of laboratory and site tests) or the instrumentation of its displacements and stress changes (using convergence meters, INCREX probe, extensometers and rigid inclusion cells), but, moreover, to undertake intensive monitoring and control of such pilot mine, which is mined exclusively in order to accomplish this research. The data transmission was made on line via Internet, to achieve a full understanding of the behaviour of the experimental mine, to access data from remote locations and to visualize results from a website. All the collected information becomes input data for several numerical models using finite differences under a program developed in the research Group, ALMEC. The simulation and a final economical analysis lead to a design of an underground exploitation, at production scale, for a resource that is traditionally mined by means of open-pit process methods that could be worked underground with less environmental impact. The main purpose achieved by this exhaustive analysis is the technical and economic viability of such mine, for their optimisation for a future productive exploitation.

Jan 1, 2003

By P. A. Laxen, P. J. van Staden

In situ leaching tests with thiourea as the lixiviant were caried out in two worked-out stopes at the No. 6 shaft at Rand Leases Gold Mining Company. Dissolution rates of 0,9 and 0,7 9 of gold per week per 100 m2 of footwal area were achieved. A major disadvantage of the method seems to be the slow rate of dissolution of the gold, which is probably caused by poor contact and slow mass transfer between the lixiviant and the gold surfaces. Under full-scale application, the loss of lixiviant by leakage could also be a very important factor. Furthermore, the oxidation products of thiourea may 'poison' the activated carbon that is used for the recovery of the gold. The method may therefore be economically viable only in stopes that contain high values of residual gold.

Jan 1, 1989

By P. E. L. Balestra, A. O. Filmer

The kinetics of the reactions involved in the non-oxidative dissolution of nickel concentrate in hydrochloric acid were studied by electrochemical and powder-leaching methods. It was found that the rate of non-oxidative dissolution increases with a cathodic shift in the mixed potential, which can be achieved by an increase in the nickel-to-sulphur stoichiometric ratio at the reaction surface. An unactivated concentrate with a sulphur content of 36 per cent exhibited a mixed potential of +O,3V (SCE) and could not be leached satisfactorily in 3 M hydrochloric acid at 60°c. When activated material (18 per cent sulphur) was leached, it had a mixed potential of -O,3V, and high iron and nickel extraction rates. Results reported by other workers on the non-oxidative dissolution of sulphides are explained in terms of the mixed potentials at which dissolution occurs.

Jan 1, 1981

By Y. -H. Chang, Y. -J. Jou, T. -S. Ueng, I. -H. Peng

In order to systematically study the size effect on the shear strength of rock joints, this study used the computer-aided-manufacturing system to reproduce the artificial rock joints for saw-toothed joints, Barton's standard joint profiles of JRC = 4~6 and 18~20, and natural rock joint profiles. We divided, enlarged, reduced, and assembled these joint profiles to obtain joint specimens of various sizes ranging from 75 mm to 300 mm in length. The shear strengths of these joint specimens were tested under different normal stresses using a direct shear test apparatus. The surface conditions of the joints at failure were also examined. The size and geometry effects on the shear strengths of these joints of various sizes and configurations were evaluated based on the test results. Um die künstlichen Trennflächen für reguläre dreieckige Trennflächen, Bartonsche standardmäßige Querschnitte der Trennflächen von JRC = 4~6 und 18~20 und natürliche Querschnitte von Trennflächen wiederherzustellen, benutzt diese Forschungsarbeit das Computergestützte-Erstellungssystem, damit die Maßstabswirkung auf die Scherfestigkeit von Trennflächen systematisch untersucht werden kann. Die Querschnitte werden geteilt, vergrößert, verkleinert und zusammengesetzt, um Trennflächenproben in Längen variierend von 75 mm bis 300 mm zu erhalten. Die Scherfestigkeit dieser Trennflächenproben wird unter unterschiedlichen Normalspannungen mit einem Direktscherversuchsgerät getestet. Die Querschnittszustände der Trennflächen bei Versagen werden ebenfalls untersucht. Nach den Untersuchungsergebnissen werden die Maßstabs- und Geometriewirkung auf die Scherfestigkeit dieser Trennflächen verschiedener Größen und Konfigurationen ausgewertet. Pour étudier systématiquement l’effet de la dimension des fractures des roches sur leur résistance au cisaillement un système de creation de fractures artificielles à l’ordinateur a été employé. Des fractures artificielles triangulaires, profils de fractures de Barton avec JRC = 4~6 et 18~20, et profils de fractures naturelles ont été reproduits. Les profils des fractures ont été arrangés de manière à obtenir des échantillons de longueur entre 75 et 300 mm. Une boîte de cisaillement a été utilisée pour étudier la résistance des fractures au cisaillement, sous plusieurs conditions de contraintes normales. Les conditions superficielles des fractures après rupture ont été étudiées. Les résultats de ces essais, effectués sur plusieurs échantillons de dimensions et configurations variées, ont contribué à établir l’influence des dimensions et de la géométrie des fractures sur leur résistance au cisaillement.

Jan 1, 2003