Search Documents

Develop an inexpensive, reliable means of quickly detecting and locating trapped miners in underground coal mines, particularly after a mine accident. The Limitations Although the Bureau of Mines has performed extensive research on the use of electromagnetics for locating trapped miners, much of its research trends toward the development of long-range systems designed to locate an underground transmitter from the surface. Such location systems are beneficial; however, there are several limitations regarding their use. Two limitations are weight and cost of the equipment. Most long-range detection systems would be too heavy and cumbersome to be accepted by miners as part of their daily protective equipment. Since such long-range detection systems are usually expensive, it would not be economically feasible for every miner to be provided with a system.

Jan 1, 1984

By W. R. Reed

A computer model named the "Dynamic Component Program" (DCP) was specifically designed for predicting the dispersion off dust from haul trucks at surface mines. Validation of the DCP was completed by comparing its results with the results of the 1SC3 model and with actual dust measurements taken front two operating mine sires. Comparisons of the field measurements, predictions of the ISC3 model and the predictions of the DCP demonstrate that the results from the DCP represent, on average, an 85% improvement truer the ISC3 dust dispersion model results.

Jan 1, 2008

By D. R. Flinn

The Bureau of Mines has studied the electrochemical parameters important to the preparation of coatings of the platinum-group metals. Using molten mixtures of sodium and potassium cyanides in an inert atmosphere, techniques have been developed that permit the preparation of baths for platinum, rhodium, and iridium electrodeposition. Cyclic voltammetric and slow sweep rate linear polarization techniques have been utilized to determine optimum potential and current values for preparation of plating baths and for the electrodeposition of coatings. Techniques are described for the deposition of platinum and rhodium coatings at near 100 percent anode and cathode current efficiencies, and for iridium at approximately 80-percent efficiency. Palladium deposition from these molten cyanide baths remains un-satisfactory. The chemistry of the palladium-containing cyanide bath is discussed. Examples of scanning electron microscope photomicrographs of typical platinum coatings are presented. Techniques are described for the preparation of platinum coatings on large objects.

Jan 1, 1982

Develop a means for analyzing seismic crosshole data to predict and monitor the Flow of leach solution during in situ mining. Background Improvements in predicting and monitoring in situ leach solution flow would aid in planning well field configurations. These improvements would also facilitate permit application by assuring regulatory agencies that leach solution would not escape from a well field undetected. Seismic tomography can detect fractured zones, which enables the prediction of probable flow paths, and it is a promising technique for monitoring leach solution injected above the water table. Tomographic analysis of crosshole seismic data provides a two-dimensional picture of the distribution of seismic velocities between the transmitter and receiver boreholes. The positions of fractured zones and of leach solution can then be inferred from the seismic velocities.

Jan 1, 1989

By L. Cheng, M. S. Seehra, P. S. Raghoottama

The four major IR bands of a-quartz at 1080, 797, 693 and 488 cm-1 are studied at room temperature by FTIR-Photoacoustic Spectroscopy. Using Rosencwaig-Gersho theory, equations for the PAS signal q for the thermally thin and thermally thick cases are derived and it is shown how thin to thick transition occurs and leads to saturation as the sample mass is increased. For sample mass < 2 mg, q is proportional to sample mass thus defining the region for quantitative analysis. The dependence of q on the chopping frequency f is found to vary as q f-n with n ? 0.9 for quartz, in good agreement with the RG theory.

Jan 1, 1989

By John Millhiser, Stephen J. Kravits

The U.S. Bureau of Mines preproduction Wireless Survey System (WSS) and its performance during an in-mine test are discussed in this report. The WSS was developed to reduce downhole surveying time in order to increase the efficiency of drilling long horizontal methane drainage boreholes in coal. Borehole survey data are electromagnetically transmitted from the WSS7s downhole guidance probe, via the drill rod, to the uph&apos;ole subsystem in less than 1 min per survey transmission, regardless of borehole depth. The WSS7s in-mine test consisted of providing borehole survey data during the directional drilling of a 2,538-ft horizontal methane drainage borehole in the Pittsburgh Coalbed. By considering available drilling time, which does not include hydraulic drill downtime and the time spent traveling portal to portal, 24 shifts were needed to complete the borehole. Of the available drilling time during the tcst, 50 pct of the time was spent drilling and 50 pct surveying and maintaining the WSS to keep it operational. Previous Bureau experience indicates drilling efficiency was increased 108 pct because of the WSS, in comparison with using a commercially available wire-run directional survey instrument at 10-ft intervals.

Jan 1, 1990

By Leonard Greenburg

The analytical procedure necessary when using this new impinger•bubbler eil)paratus is almost identical with that em:r;,loyed with the Palm0r a:pp8.ratua. As sugar is not employei, the new apparatus por.;sesses the advantage over the eug.r tube method in having vsry low control errors, being, therefore, much simple in laboratory manipulation during analysis.

Aug 1, 1922

By S. J. Davenport

[The tremendous increase in mine mechanization since 1929 has increased markedly the application of electric power in and about the coal mines of the United States. Cutting, drilling, and leading machines have replaced hand-mining methods in nary mines. As a result, expansion of the gathering haulage has necessitated introduction of extensive feeder, trolley, grid other power wires. (1)3/ In spite of this vast mechanization the fatality rate from electric shock has been on the decline. However, there are still too many accidents, and efforts to eliminate electrical hazards cannot be relaxed. It is hoped that an acquaintance with the physiological aspects of electrical accidents will make workers end management aware of the lurking dangers of this very common and extremely dangerous form of energy.]

Jan 1, 1951

By Alan R. Buehler

A mineral survey of the 20,792-acre Sand Butte WSA (Wilderness study Area), ID-57-8, was conducted by U.S. Bureau of Mines personnel in 1985, at the request of the Bureau of Land Management. The WSA is in Lincoln County, south-central Idaho, about 15 miles south-southeast of Carey. There are no mines, prospects, or claims within the WSA. Basaltic lava is the only rock type exposed within the WSA. The only mineral resource is a few tons of a platy variety of lava (slab pahoehoe) which is suitable for use as decorative stone. Similar slab pahoehoe, produced from other lava fields in southern Idaho, retails for approximately $125/ton. The deposit in the WSA is too small to be mined commercially but may have value to consumers who gather their own decorative stone. INTRODUCTION A mineral survey of the Sand Butte WSA (Wilderness Study Area) 1/ was conducted in June 1985 by the USBM (U.S. Bureau of Mines) and the USGS (U.S. Geological Survey) at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will he used to help determine the suitability of the WSA for inclusion into the National Wilderness Preservation System. The immediate goal of this and other USBM mineral surveys is to provide data to the President, Congress, government agencies, and the public for land-use decisions. The long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By Carla A. Kertis, Alan A. Campoli, Claude A. Goode

This Bureau of Mines study was conducted to obtain a better understanding of the coal mine bump problem and its effect on underground coal mining in the Eastern United States. To accomplish this, information was collected on the geologic conditions, mining techniques, and engineering parameters at five bump-prone mines. Two geologic conditions have been found to cause the occurrence of bumps in the Eastern United States: (1) relatively thick overburden and (2) extremely rigid strata occurring immediately above and below the mine coalbed. Additionally, the probability of bump occurrence is increased by certain mining practices that concentrate stresses during retreat mining, in areas where geologic conditions are conducive to bumps. Mining plans that permit the development of pillar line points or long roof spans that project over gob areas should be avoided because these features may contribute to the occurrence of bumps.

Jan 1, 1987

By Uwe Kaulbars

Vibration measurements at the workplace are often complicated and expensive. The assessment of the risk in conformity with EC Directive 2002/44/EC “Vibration” (which lays down the minimum requirements of laws in Europe for occupational safety and health) can therefore be carried out on the basis of an estimate based on information from manufacturers as well as by measurement conforming to ISO 5349. The characteristic values (emission values) determined by manufacturers in laboratory conditions may deviate from the exposure values measured at source at the workplace. Equally, deviations may arise as a result of the delay in the changeover of test methods from the single axis of measurement to the total vibration value for the three axes of measurement conforming to ISO 20643. To prevent faulty estimates, the manufacturer’s information has to be corrected by a tool-related factor in accordance with CEN/TR 15350. By taking the example of masonry and stone working machines, the empirically determined tool-related correction factor is checked and confirmed. Methods Vibration measurements were carried out in accordance with ISO 5349 in practical application conditions on 10 selected typical eccentric and orbital sanders, concrete and disc grinders as well as on wall chasers and stone saws. Results The total vibration value obtained for the investigated tools rangedfrom ahv = 3.6 m/s² to ahv = 11.6 m/s². When the values from the practical measurements are compared with the manufacturer’s vibration values, the underestimation of the risk occurring in some cases can be largely compensated for by the tool-related factors conforming to CEN/TR 15350 (see Figure 1).

Jan 6, 2006

By Richard E. Hucko

The bureau of Mines conducted a laboratory scale investigation of the process of selective flocculation with the objective of developing a method to effect separations on suspensions consisting predominately of ultra-fine-size (minus 400-mesh) particles of coal and refuse. Selective flocculation of coal from coal-refuse slurries could be achieved with a wide variety of reagents. Typically as much as 15 to 20 weight-percent of high-ash solids (70 to 80 percent ash) could be retained in suspension. The flocculated sediment remained a high-ash product, however, and would require further treatment to be regarded as clean coal. No combination of reagents and conditions led to selective flocculation of the refuse component. The dispersing agent was found to be the critical factor; dosages of 3 to 8 lb/ton2 were necessary to stabilize the suspension for subsequent selective flocculation. In addition, most of the dispersants that worked were most effective at substantially elevated pH (11 or so). It was concluded that this process would be prohibitively expensive and, because of yield and quality constraints, it would be of questionable utility in today&apos;s coal preparation industry.

Jan 1, 1977

By Seth C. Schaefer

The Bureau of Mines studied thermodynamic properties of liquid Al-Si alloys with the high-temperature galvanic cell Al(1)//Al+3(AlC13 in NaCl?KCl)//Al-Si alloy(1). Activities of aluminum and silicon (referred to pure liquid metals) show a pronounced negative deviation from Raoult&apos;s law in liquid Al-Si alloys containing 0.9 to 35.2 atomic-percent silicon. Activity coefficients and the properties [?Gi, ?GxS ,?H, ?G, ?Gxs , and ?S] have been derived from the experimental data and are summarized in tables and illustrations.

Jan 1, 1974

By M. J. Ferrante

The Bureau of Mines determined the enthalpies of Ni3S2 relative to 298.15 K to provide new thermodynamic data for advancement of mineral science and technology. Enthalpies were measured with a copper-block calorimeter from 298.15 to 1,197 K. A solid-solid transition was found at 834±1 K, with an isothermal heat absorption of 13.32 kcal/mol. The temperature of this solid-solid transition was accurately measured by differential scanning calorimetry. Because Ni3S2 does not melt congruently, the heat of fusion of 4.70 kcal/mol was obtained by extrapolation of enthalpy measurements from the solid and liquid phases to approximately 1,064 K. Tabulated values are given for the relative standard enthalpy, heat capacity, entropy, and Gibbs energy function between 298.15 and 1,800 K. Enthalpies are also given in equation form and combined with data from the literature to derive values of standard enthalpies of formation and Gibbs energies of formation. Similar calculations were made for the reaction of crystalline and liquid nickel with gaseous diatomic sulfur for Ni3S-2(c, l).

Jan 1, 1982

Develop a user-friendly computer program that permits those interested in mine health and safety to access and analyze on a personal computer (PC) employment, production, and accident data for U.S. coal and metal-nonmetal mines. This software is being designed with a major focus on flexibility and case of use. The Mine Accident Decision Support System (MADSS) will be available for distribution in mid-1994. Currently, the U.S. Bureau of Mines (USBM) is seeking volunteers willing to pilot test a preliminary version of the software and to provide suggestions for its improvement. Background Since 1975, the Mine Safety and Health Administration (MSHA) has compiled large data bases of information about U.S. mines and the reportable accidents, injuries, and illnesses that have occurred in those mines. Employment and production data arc collected on a quarterly basis from each mine and accident information is collected on an incident -by-incident basis. The USBM has compiled estimated costs for each of these accidents using computer models. All of this information is potentially useful to mine health and safety researchers. However, it has been underutilized because it is stored in large mainframe data bases that arc inaccessible to many users and/or are cumbersome and difficult to use.

Jan 1, 1993

By R. Karl Zipf

Use of Salamon&apos;s stability criterion in underground mine design can prevent the occurrence of catastrophic domino-type pillar failure. Evaluating the criterion requires computation of the local mine stiffness and knowledge of the post failure behavior of pillars. This paper summarizes the status of the practical use of this important criterion and suggests important research to improve our capabilities. Analytical and numerical methods are used to compute the local mine stiffness. Work to date in computing local mine stiffness relies mainly on elastic continuum models. Further work might investigate local mine stiffness in a discontinuous rock mass using alternative numerical methods. Existing post failure data for coal pillars are summarized, and a simple relationship for determining the postfailure modulus and stiffness of coal pillars is proposed. Little actual postfailure data for noncoal pillars are available; however, numerical models can provide an estimate of post failure stiffness. Important factors controlling postfailure stiffness of rock pillars include the postfailure modulus of the material, end conditions, and width-to-height ratio. Studies show that the nature of the failure process after strength is exceeded can be predicted with numerical models using Salamon&apos;s stability criterion; therefore, a method exists to decrease the risk of this type of catastrophic failure. However, the general lack of good data on the postfailure behavior of actual mine pillars is a major obstacle. Additional back-analyses of failed and stable case histories in conjunction with laboratory testing and numerical modeling are essential to improve our ability to apply the stability criterion.

Jan 5, 1999

By John B. Umhau

[&apos; is ann.tal surve:&apos; gives sta.tistical data regC:ll~dirg rims.ry and feCOA-dUTY or ~cra:p tin used in thL United States by industries anc. includcc dc..ta l&apos; is ann.tal surve:&apos; gives sta.tistical data regC:ll~dirg rims.ry and feCOA-dUTY or ~cra:p tin used in thL United States by industries anc. includcc dc..ta ]

Jan 1, 1938

By V. A. Marple, K. L. Rubow

"Filter samplers are one of the simplest methods and, in some instances, one of the only methods that can be use to obtain samples of particulate matter suspended in a gaseous medium. Once collected, particles are normally analyzed directly on the filter by gravimetric, chemical or microscopic techniques. However, it is sometimes desirable to resuspend the particles in an airstream for analysis. This would be the case if the size distribution of the particles were to be measured using one of many particle sizing techniques such as inertial classifiers, optical particle counters or the TSI Aerodynamic Particle Sizer CAPS).A ·technique has been recently developed whereby one can resuspend particles from filter samples in an airstream. The technique has been used for the resuspension of coal dust from filters. The resuspended particles were then introduced into the APS. This development was necessary since an APS can not be taken directly into an underground coal mine. For this application, particle samples are collected on membrane filters in the underground mines. The mass concentration of the particles determined through gravimetric analysis. The particle size distribution was tl1en determined by resuspending the particles and passing them through a TSI Aerodynamic Particle Sizer (APS). Excellent agreement has been obtained between the size distribution directly measured underground with a cascade impactor and that measured from the resuspended particles. For this experiment, an open-faced filter sampler was placed adjacent to the cascade impactor in the n1ine. The particles collected on the filter were resuspended in the laboratory and Measured with the APS.A venturi aspirator is used in the apparatus developed for resuspending the particles. The venturi has a small diameter capillary tube placed in the venturi throat. High velocity air flow is passed through the venturi, thereby, creating a low pressure region at the exit of the capillary tube. The low pressure draws air through the tube. The filter with deposited particles is located at the inlet to the capillary tube where the air flow into the capillary resuspend the particles. Once airborne, the particles are deagglomerated as they pass through the high velocity air flow in the venturi throat."

Jan 1, 1989

By Leon E. Esparza

The Bureau of Mines studied 780 acres of the 24,130-acre Sheldon Contiguous Wilderness Study Area (CA-020-1012) in 1985. The study was done at the request of the Bureau of Land Management and authorized under the Federal Land Policy and Management Act (Public Law 94-579, October 21, 1 976) in order to evaluate the mineral resources. The study area is located in Washoe County, NV, about 35 miles northeast of Cedarville, CA. A search of county courthouse records and an examination by foot traverses through and adjacent to the study area did not reveal evidence of any mining or mining exploration activity past or present. In addition, evidence of any form of rock alteration was not observed. Evidence of mineral resources is not apparent. Although basalt, the only rock-type present in the study area, can have some limited industrial applications, sources closer to potential markets probably would preclude rock from this area being economically competitive. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of the Sheldon Contiguous study area at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys ;s to provide data for President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By S. R. Wilson

[The Anniversary-Bucky pegmatite is one of the largest, dikes in the Quartz Creek district, 21 miles east of Gunnison, Colo. The major dike consists of quartz-albite pear pagmatite and graphic granite with many quartz masses as individual cores occurring within the dike. A mining operation on one of the largest core areas has exposed several mineralogic cones directly associate with the core. These zones, including the large- units of the dike, are quartz pegmatitc, quartz-perthite pegmatite, perthite pegmatite, muscovite-feldspar -quartz pegmatite, quartz-albite pegmatite, and perthite-quartz (graphic granite) pegmatite. Muscovite and beryl are found in the muscovite-feldspar-quartz zone and are the only two products that have been marketed. Other potential products are perthite, graphic granite, and possibly small quantities of columbite-tantalite, monazite, and related radioactive minerals. The Bureau of Mines drilled two diamond-drill holes during April 1950 to investigate the largest and cost promising core area. This, report describes the results of this drilling.]

Jan 1, 1953