Search Documents

By R. H. Sprute

Underground accumulations of slimes in the Henderson mine are routed to two large collection pits where they are dewatered and consolidated by application of direct current. Densified material is then removed to ore cars by rubber-tired front-end loaders and transported out of the mine. This Bureau of Mines report describes the electrical dewatering installation and compares its efficiency of operation with that predicted from preliminary laboratory studies performed by the Bureau. Direct current from a 150-kw rectifier (applied for 44 hours at 400 amperes and 65 to 70 volts) converted slimes containing 25.3 percent solids to material ranging from 44 to 65 percent solids. Better results can be expected if the ramp and front sections of the pits are treated separately, using higher current density.

Jan 1, 1980

By Robert L. Rough

The 1954 field tests consisted of six experimental shots in relatively deep holes in a sandstone similar to many oil-bearing sandstones. Water-injection measurements were made before and after each shot to establish the change in conductivity of the fluid caused by the shot. The pressure pulse produced by the shot was recorded in nearby holes to monitor the shot and to determine if any relation existed between the change in conductivity and the nature of the pressure pulse. The results of water-injection tests showed the range of conductivity of fluid before and after shooting with two different types of explosives. Because of the large spread in data for similar shots, not enough information was available to evaluate the differences in increased conductivity produced by the two explosives or any relation between the increased conductivity and the nature of the pressure pulse. However, these results, with the results of other tests involving explosive shots in rock, provide guidance for future research on the oil-well-shooting problem.

Jan 1, 1957

By Raymond B. Lucas

"Distinction between Tripoli and Diatomaceous EarthMuch confusion exists both in the literature and in the trade as to the proper use of the terms tripoli, tripolite diatomeceons or infusoriai earth, and kieseigunr. All of these terms are often used synonymously by the trade and even in mineralogists and other reference books. Actually, tripoli is a ma- is a material of definite and distinct physical and chemical properties and all of the other terms belong to a different material with just as definite and distinct properties.Originally the term tripolite (loosely called tripole) was given to a diatomaceous cart from Tripoli in Northern Africa. Dena (J.D. Dana, A System of Mineralogy 6th Ed.) calls this material tripolite and gives no authority for the use of the terms tripoli. Between 1880 and 1890 the deposits near Missouri, were opened and the material placed on the market as ""Tripoli"" no doubt due to its resemblance in some respect to the original tripolite or diatomaceous worth from Tripoli. Since that time the term tripoli has with increasing definitenesss been reserved for the Seneca material and other siliceous of similar origin and physical properties, while all siliceous material of organic origin, containing dilators, has been called diatomaceous earth (or its synonyms infusorial earth, kiselguhr, etc.). Rottenstone is sometimes classed with tripoli."

Nov 1, 1920

By J. E. Pahlman

The Bureau of Mines conducted re-search to determine the resistance of basic refractories to corrosion by ash slags that would result from the burning of coal and lignite in metallurgical operations. Basic refractories are of economic interest because they are from one-third to one-half as expensive as 90-to 99-pct-alumina refractories. Static tests were performed at 1,300° C and dynamic tests at 1,400° to 1,650° C to investigate the stability of refractory specimens in a slag environment. In alkali-containing lignite ash slags, in order of decreasing resistance, magnesite, magnesite-chrome, and chrome-magnesite refractories all had corrosion resistances equal to or better than 90-to 99-pct-alumina refractories. These basic refractories formed slag penetration layers in dynamic tests, which helped protect them from further attack. Chemically bonded basic refractories in general did not have as good a resistance to slag attack as did burned refractories of the same composition. In very acidic coal ash slag, a chrome-magnesite refractory containing 30 pct MgO plus a slag inhibitor and direct-bonded magnesite-chrome refractories with 60 pct MgO had good resistance to attack. Chrome-magnesite refractories (30 to 40 pct MgO) were moderately to severely attacked, and refractories with greater than 70 pct MgO were severely attacked by this same slag.

Jan 1, 1982

By E. Morrice

Techniques developed by the Bureau of Mines for the preparation of high-purity rare-earth metals and their alloys by electrolysis of the oxides in fluoride media are summarized. Cerium, lanthanum, neodymium, praseodymium, dysprosium, gadolinium, and yttrium metals, the mixture didymium, and specific alloys of these metals and samarium with iron, nickel, chromium, and cobalt were prepared. Individual metals were electrodeposited in the liquid state on tungsten or molybdenum cathodes. Alloys were prepared by electrodepositing the rare-earth metal on a consumable cathode, at a temperature above the melting point of the eutectic formed between the rare-earth element and the cathode material. Cells were designed for electrowinning metal products in gram and pound quantities, and methods for continuous electrowinning of cerium and lanthanum were developed.

Jan 1, 1968

By T. Ruff

Researchers at the National Institute for Occupational Safety and Health, Spokane Research Laboratory, studied technology and methods that could reduce accidents involving surface mining equipment that collides with other vehicles or workers, or drives over an unseen road edge. These accidents are partially attributed to the lack of full visibility around these large pieces of equipment. Blind areas can be extensive and this report presents plots of blind areas for five pieces of surface mining equipment. Several technologies designed for detecting obstacles in blind areas and providing a warning to the operator were evaluated on off-highway dump trucks. These proximity warning systems included radar, sonar, GPS, radio transceiver tags, and combinations of radar and cameras. A summary of test results is presented in this report, along with guidance on effective proximity warning technology, installation and maintenance considerations, and recommendations for effective implementation. This study found several commercially available systems that could effectively warn an equipment operator of an impending collision. Several new technologies also show promise for reducing these accidents. In most applications, it is recommended that sensor-based systems be combined with video cameras to provide important alarming functions along with an actual view of the blind area.

Jan 6, 2007

1. In 2002, a total of 2,820 contracting companies reported employment at coal mines to MSHA.

Jan 1, 2004

Provide reasonably priced, reliable fire protection for AN-FO haulers. Approach An automatic fire sensing and suppression system for AN-FO haulers was developed and on-vehicle tested. How It Works The system works in two ways to protect personnel from dangerous and unpredictable AN-FO fires. First the system senses and suppresses fires on the truck before they spread to the AN-FO in the bunker. This design was chosen because AN-FO truck fires generally start when combustible liquids (such as diesel fuel, hydraulic fluid or lubricating oils) are ignited by hot surfaces mainly on three areas: the engine, the transmission or the power take-off. These fires are quickly sensed by a linear temperature sensor strung throughout these three areas. The system then warns the operator and automatically suppresses the fire by discharging 30 pounds of multipurpose dry chemical extinguishing agent through a network of fixed hoses and nozzles. Second, this system includes six spot thermal sensors mounted inside the bunker on the truck to monitor the AN-FO temperature in case a fire does spread to the bunker area. If the bunker temperature rises to 190° F, a loud siren is sounded to warn nearby per-

Jan 1, 1981

By E. E. Harton

Bureau of Mines Information Circular 7516, Bibliography of Investment and Operating Costs for Chemical and Petroleum Plants, was published in October 1949 to aid in estimating investment and operating costs of processes for manufacturing synthetic liquid fuels. Development of such processes by the Bureau of Mines was authorized by Public Law 290, 78th Congress. This bibliography included references to and abstracts of publications appearing from. 1930 to September 1948 on all processes in general use in the petroleum refining and chemical industries. Bureau of Mines Information Circular 7705, Supplemental Bibliography on Investment and Operating Costs for Chemical and Petroleum Plants, was prepared to cover the area from September 1948 through June 1952.

Jan 1, 1956

By Cecil E. Lester

Since the advent of coal mining, the minimal lighting in the under¬ground working place has been an obstacle to the safe and efficient performance of the miner's many tasks. Compounding this problem is the fact that the machines being operated in the working place are so large that the vertical and horizontal clearances around the machinery are severely limited. Consequently, in these poorly lighted and congested working places, the machine operator is unable to utilize his peripheral vision. He cannot see hazards as they develop and, too often, cannot react in time to avoid serious injury or death to himself or his fellow miners. The greatest hazard to miners inby the last open crosscut is from falls of roof which are often preceded by warning signs such as falling rock fragments, roof supports taking weight, or a sudden reduction in the height of the working place. These warning signs often go undectected because the machine operator's attention is focused on the small circle of light emitted from his cap lamp. Congress recognized the illumination deficiencies, and, in the Federal Coal Mine Health and Safety Act of 1969, charged the Secretary of the Interior with the authority and responsibility for development and promulgation of minimum standards for illuminating working places in coal mines. These standards have been developed and, as stated in the April 1, 1976 Notice, Federal Register, Volume 41, No. 64, will be promulgated on October 1, 1976, as mandatory regulations under Section 75.1719, Title 30, Code of Federal Regulations. The regulations require that the designated surfaces within the miner's normal field of vision be illuminated to 0.06 foot-lamberts while self¬propelled mining equipment is being operated in the working places. The term "working place" is defined in the Act as "the area of a coal mine inby the last open crosscut".

Jan 1, 1976

By Dean H. Ambrose

This paper presents an approach for representing and analyzing random motions and hazardous events in a simulated three-dimensional workplace, providing designers and analysts with a new technique for evaluating operator-machine interaction hazards in virtual environments. Technical data in this paper is based upon a project striving to reduce workers' risks from being hit by underground mining machinery in a confined space. The project's methodology includes human factors design considerations, ergonomic modeling and simulation tools, laboratory validation, and collaboration with a mining equipment manufacturer. Hazardous conditions can be analyzed in virtual environments using collision detection. By simulating an operator's random behavior and machine's appendage velocity, researchers can accurately identify hazards, and use that information to form safe design parameters for mining equipment. Analysts must be discerning with the model and not read more from the databases than what the simulation model was designed to deliver. Simulations provided an interesting approach to data gathering in that there was no need for live subjects and logistics - test sites and costs associated with experiments-became insignificant. Collisions versus speed, operators' size, and risk behaviors proved the versatility found in the data obtained from the model. Preliminary results show that response time significantly affects the number of collisions experienced by the virtual subject. Also simulation data suggests that more mishaps occur with hand-on-boom-arm risk behavior.

By Charles L. Kimbell

This study summarizes and amalgamates much information collected, compiled, and utilized by the Bureau of Mines numerous country specialists and branch chiefs for inclusion in their country and regional reports that comprise the five other volumes of the international studies of the Minerals Yearbook. Because of the plethora of sources used in preparing these regional studies, it is impossible to cite all sources of information used in preparing this summary, but some recognition seems due. Generally speaking, the preparation of this study, and its related detailed studies on countries and areas, would be impossible without the efforts of the personnel of our counterpart agencies throughout the world. Information that they collect, compile, and then publish, either in their own volumes or in publications of central statistical agencies in their countries, are the foundations upon which this work rests. Thus, we must begin by expressing our appreciation to the multitude of persons employed by these agencies for their contributions.

Jan 1, 1992

By Franklin B. W. Woodbury

The Bureau of Mines undertook the development and evaluation of a system to provide a simultaneous, on-line determination of both iron and silica in iron ore beneficiation streams as part of a program to improve the efficiency to mineral separation processes, Californium-252 (252-Cf) was the neutron source used in the system for measuring the amounts of silica and iron in bulk slurries by thermal neutron capture-gamma ray spectra analysis. The theory of thermal neutron capture-gamma ray reactions and their potential application to mineral processing stream analysis is discussed. The prototype system and supporting software developed by the Bureau is described. During the initial phase of the work, both simulated and actual pilot plant slurries were investigated using a 60-to 32-µg 252-Cf neutron source. The percent solids of the slurries was ranged from 2 to 40 percent and the silica and iron content ranged from 1.5 to 83 percent and from 10 to 65 percent, respectively. Accuracy of the determination of the components in the solids was dependent upon the percent solids in the slurry.

Jan 1, 1980

By Wilbur I. Duvall

Nineteen quarry blasts were instrumented with particle-velocity gages mounted in a uniform soil overburden, back of one face in a quarry in Iowa. Three components of particle velocity, radial, vertical, and transverse, were recorded at each of eight stations back of each blast. Distances from blast area to gage stations ranged from 150 to 3,000 feet. Eleven of the quarry blasts employed millisecond delays, and eight were instantaneous blasts. Charge weight per hole was 200 pounds, and the charge weight per delay interval, including the instantaneous blasts, ranged from 100 to 3,000 pounds. Analysis of the data from these tests shows that the particle velocity, V, produced at distance, D, by a quarry blast of charge per delay interval, W, can be represented by an equation of the form, V=KWb D-n, where b and n are exponents, and K is the intercept constant which is a measure of the level of vibration. The value of K for a millisecond-delayed blast employing one hole per delay interval is about 42 percent larger than the value of K for a single-hole blast. The value of K for a multiple-hole milli-second-delayed blast is about the same as that for an instantaneous blast when the charge per delay for the millisecond blast is equal to the total charge for the instanteneous blast. The vibration level from millisecond-delayed blasts employing one hole per delay is shown to be independent of the length of the delay interval and the number of delay intervals over the range of the variables tested: 9, 17, and 34 milliseconds and 3, 7, and 15 delays per blast.

Jan 1, 1963

By David C. Oyler, William P. Diamond

Three long horizontal holes were drilled from a directionally drilled sur¬face hole at the Emerald Mine near Waynesburg, Pa. The purpose was to adapt the technique of directional drilling for use in draining methane from coalbeds. A 504-m (1,652-ft) long, 76-mm (3-in) diam¬eter, circular arc pilot hole was drilled, using a downhole mud motor, to enter the Pittsburgh coalbed at a verti¬cal depth of 305 m (1,000 ft). The hole was reamed to 222 mm (8-3/4 in) and was cased to a measured depth of 486 m (1,595 ft). Three 76-mm (3-in) diameter horizontal drainage holes were then drilled, totaling 2,909 m (9,544 ft) of horizontal hole. Improvements in drilling methods increased the average drilling rate from 20.4 m (67 ft) to 64.9 m (213 ft) per day. The cost of drilling the directional and horizontal holes (using a Government-owned drill rig) was $1,169,530, a figure inflated by inexperience and by delays caused by lost-circulation problems and fishing operations. An estimated total drilling cost of $960,000 (including rental of a drill rig) for an improved system, was determined by a detailed cost analysis. Initial gas and water production from November 1979 through May 1980 was low because of caving of the horizontal holes drilled in shale near the bottom of the casing.

Jan 1, 1982

By J. W. Paul

"The economic features of coal mining must take into account the drain on the man power. Study over a recent 5-year period reveals an average yearly loss of 2,125 underground men, of whom 1,182 are killed by falls of roof and coal, and according to recent data compiled by the Bureau of Mines it is estimated that 54,000 men sustain lost—time disabling injuries from the same cause.Under normal activity of the mines approximately 50 lives are taken by falls of roof during every 10 days the mines are operated, or 5 persons are killed per day, which, at a compensation charge of $5,000 each, amounts to $25,000 per day. Add to this the similar number killed by causes other than by falls of roof and we have $50,000 as an approximate daily fatality charge for each day the mines operate. On the basis of 200 working days per year, this amounts to the alarming figure of $10,000,000 annually. An investment at 5 per cent to yield this amount would require $200,000,000, which is equivalent to a capital investment of $0.40 per ton of coal, produced annually, on the basis of 500 million tons. These figures apply only to fatalities for which a fixed or stated amount is paid for compensation and do not include the compensation and hospitalization paid for the approximately 103,000 upon whom idleness is enforced by a lost-time disability injury. In one State having an annual production equal to approximately 30 per cent of the total bituminous production of the United States, the most recent data shows that for each fatality there are eight serious injuries causing 60 days or more lost time. The frequency rate of accidents for that State is less than the average for the United States, and so a conservative comparison may be made by using the figures of that State in estimating the total serious injuries, which gives 16,000 as losing 60 days or more. The average number of underground employees in the coal mines of the United States for the past 10 years has been approximately 570,000; the annual underground fatalities amount to approximately 2,000 and non-fatalities to 108,000, or a total of 110,000, which means that one out of every 5.17 employees ,or 19.3 per cent, receives an injury which results in either a fatality or a lost-time disability; this figure in a little over five years will reach a number equivalent to 100 per cent of all underground workmen. Against this is the record of many miners who have worked 25 years or more without a lost—time disability injury, indicating that coal mining is not necessarily productive of injury or death to workers.In the matter of falls of roof, it is found that 85 to 87 per cent of all fatalities occur at the working face, face of a room or entry, or in pillar work. It is at the working face that the greatest roof hazards are encountered, and when about 75 per cent of the underground employees spend approximately 90 per cent of their working hours at the face, it is logical that there is where injury is most likely to occur.Although the roof hazards may vary in different beds of coal, experience has proved that roof hazards can be successfully controlled in all coal mines, essentially regardless of the character of the roof if constant care and attention are given by the management and employees in applying the principle of safety. In almost every mining district some companies maintain an extremely low frequency rate of injury, whereas in the same district with essentially the same roof conditions the opposite is true.A study has recently been made of a number of reports upon fatalities in one district of one of the principal coal—producing States and it showed that 50 lives had been lost at 23 mines as the result of falls of roof or sides. These reports were made by the mine officials, safety engineers, and safety committees and an attempt was made to give both the cause and the person or factor responsible for the fatality. A summary of the items of responsibility is as follows:"

Feb 1, 1932

By J. E. Tiffany, Z. C. Gaugler

"In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 20 and 25 outlining the conditions in use under which, and only under which, the explosive or blasting device is permissible.In view of a recent publication recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 20 and condition 2 on page 25. An explosive or a blasting device enumerated in the permissible lists of this Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.PERMISSIBLE EXPLOSIVES TESTED UNDER SCHEDULE 17CAn active list of permissible explosives was published in October 1938 as part of Bureau of Mines Report of Investigations 3421, under the title ""Active List of Permissible Explosives and. Blasting Devices Approved Prior to June 30, 1938."" This list included 191 brand names.Changes in the list that have been authorized to June 30, 1939, placed 56 additional brands of permissible explosives on the active permissible list as a result of tests, changes in brand names, or transfer from the inactive list. Fifty-seven permissible explosives were transferred from the active to the inactive list. The brand names of four explosives were rescinded curing the year. The present list contains 18G brand names. The brand names of the Permissible explosives placed on the active list are as follows:"

Sep 1, 1939

By James J. Bryja, Thomas M. Barczak, Dennis R. Dolinar, Joe Bower, Thomas P. Mucha

Maintaining ground stability in the gate roads, particularly the tailgate, has always been critical to the success of longwall mining, both in terms of safety and productivity. Several new support technologies have been developed in recent years to replace conventional wood and concrete cribbing for secondary roof support. Since their performance characteristics are unique, the best practices that have been developed with conventional wood cribbing may not be applicable for these alternative support technologies. Therefore, with so many options to consider and the importance of achieving adequate ground control at minimal cost, the trial and error approach to longwall gate road support is no longer prudent. This paper discusses a design methodology for standing secondary tailgate supports. This design technique requires in-mine measurements of tailgate support loading and convergence to establish a tailgate ground, reaction behavior based on the support and strata interaction. The methodology uses the performance characteristics generated in the National Institute of Occupational Safety and Health (MOSH) Mine Roof Simulator (MRS) to match the stiffness and load characteristics of various supports to the measured ground reaction behavior. It can be used to determine the appropriate -- application of alternative roof support systems or to design in- mine trials such that a fair and equitable comparison of different support systems can be made. A case study if the methodology at a western Pennsylvania mine site is presented in the paper, including a comparison of four alternative support technologies to conventional wood and concrete cribbing historically used at this particular mine.

By Floyd G. Anderson

Bureau of Mines studies show than an electronic counter can be used for determining just concentrations from midget impinger samples collected in bituminous coal mines. A sample correlation coefficient of 0.91 for data obtained using the electronic counter and the Bureau of Mines microprojector procedures indicates a significant linear relationship between the methods. The electronic counter provides better counting precision and reduces analytical time.

Jan 1, 1968

By Thomas H. Dubaniewicz

The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, conducted a study of past mine explosions to identify the ignition locations and ignition sources responsible for the most severe explosion events resulting in death. Since the Scotia disaster of 1976, many fatalities from underground coal mine explosions have been linked to nonpermissible electrical equipment ignition sources located in intake air courses. With few exceptions, explosion protected equipment is generally not required in intake air courses of gassy underground coal mines in the US. Cigarette lighters were another prevalent ignition source for fatal explosions ignited in intake air courses. Several mine rescue/ recovery teams have encountered electrical ignition hazards. The study provides evidence that intake air courses of gassy underground coal mines fit the description of certain Hazardous (classified) locations described in the US National Electrical Code®. Class I Division 2 or Zone 2 explosion protection tech¬niques may be used to design intake air equipment so that it does not present an ignition source under normal operation, before mine power is shut down in emergency situations. Nonpermissible circuits in intake air courses that are likely to remain energized during emergencies, e.g. battery powered equipment, should be protected by more stringent Class I Division 1, Zone 1, or Zone 0 techniques, to protect rescue/recovery personnel.

Jan 1, 2009