Search Documents

By K. O. Bennington

The thermodynamic properties of aegirine, of composition [(Na0.869Fe30+7362 Fe20+16Mn0.03Ca0.1121)(A10.141Sil 9738)(06)], were experimentally determined at the Bureau of Mines as part of its efforts to advance minerals technology. The standard enthalpy of formation determined by hydrofluoric acid solution calorimetry is AHf298 = -641.12±0.73 kcal/mol. The standard enthalpy of formation from the oxides is AH298 = -37.136±0.509 kcal/mol. Low-temperature heat capacities were determined by adiabatic calorimetry from 19.1 to 304.6 K. The derived standard entropy is S298 = 38.03±0.14 cal/mol?K. The heat capacity was measured over the range 348 to 1,198 K by differential scanning calorimetry. These experimentally determined data were combined with data from the litera¬ture to calculate the Gibbs energies of formation and equilibrium constants of form¬ation over the temperature range of the measurements. Standard enthalpies of forma¬tion are given as functions of temperature. The standard Gibbs energy of formation at 298.15 K is AGf298 = -600.36 kcal/mol.

Jan 1, 1984

By L. Kaufman

Fifteen boride composites were synthesized by hot pressing and evaluated by physical and incendivity testing as non-sparking tool materials. The incendivity tests, conducted at the U. S. Bureau of Mines, Albany Research Center, compared the boride compo-sites with standard cobalt-bonded tungsten carbide material used for coal cutter bits. Two titanium diboride composites and two zirconium diboride composites out-performed cobalt-bonded tungsten carbide in wear resistance and reduced tendency to cause ignitions. However, three of these candidates exhibited undesirable chipping. The remaining candidate, a TiB2-(Ni, Cu) composite, did not chip, nor did it cause ignitions at levels where cobalt-bonded tungsten carbide tools caused ignitions in the incendivity tests. Thus, this material appears to be a logical candidate for further development.

Jan 1, 1973

By D. R. Mathews

The solubility of carbon in electrorefined vanadium was determined to be approximately 0.27 wt pct at the eutectic temperature 1,650° C and 0.03 wt pct at 700° C. The tensile strength and hardness of vanadium increased with car-bon content to the solubility limit, but this effect was small, probably because of the narrow solubility range. Between the solubility limit and 0.3 weight-percent carbon, the second phase had essentially no strengthening effect in vanadium. The second phase, observed metallographically at the grain boundaries and within the grains, was shown by autoradiography to contain high-carbon concentrations. This second phase was identified as VgC by X-ray analysis. The VgC in the grain boundaries contributed largely to the poor cold-and-hot workability of vanadium-carbon alloys. Increased concentrations of V2C occurred at the grain boundaries of the high-carbon alloy ingots as a result of homogenization at 1,600° C for 1 hour. Alloy ingots containing more than 0.36 wt pet carbon (a calculated 2.9 wt pct VaC) following homogenization, cracked severely and failed by intergranular fracture upon swaging at 900° C.

Jan 1, 1965

By A. F. Colombo

The differences in starch demands that occur between ore types subjected to the anionic flotation of calcium-activated gangue and the range of residual starch contents expected to give the best metallurgical response were evaluated on a batch and pilot plant basis. A phenol-sulfuric acid procedure was used to determine the residual starch contents in the iron ore slurries. Three pilot plant campaigns on samples from a group of orebodies located on the Marquette Range, Michigan, showed that in the rougher flotation pulp, a residual carbohydrate range of 25 to 100 ppm, which is equivalent to a 0.5 lb/short ton spread, yielded optimum results. Concentrates assaying at least 65 percent Fe and less than 6.0 percent Si02 and containing more than 80 per-cent of the recoverable iron were obtained. Both batch and continuous research indicated that starch adsorption is calcium modulated and relatively unaffected by the fatty acid additions employed. Residual starch level is not a critical control factor, but the addition must be adjusted to about 25 to 50 ppm residual starch and kept in this range for most effective utilization of the added tapioca flour.

Jan 1, 1972

This chapter focuses on smoke as it relates to escape from underground mine fires. Among the topics discussed are the measurement of visibility in smoke; smoke-related hazards such as the production of CO, hydrochloric acid (HCI), or other byproducts of combustion; and miners' personal experiences while escaping through smoke. Smoke Measurement and Visibility In general, smoke consists of hundreds of thousands of very small particles. These particles have some "size," usually expressed in terms of their diameters, and they have some concentrations, usually expressed either in the number of these particles per unit volume or the total mass of the particles per unit volume. Humans cannot see individual smoke particles because they are too small. Similarly, "umber concentrations" and "mass concentrations" of smoke particles do not have much meaning to people unless they are trained technically. Still, individuals know that they can see smoke, independent of all the technical jargon used to describe it. Also, they know that when the smoke level gets too high, it is no longer visible. In fact, nothing is visible because the smoke absorbs all of the light in its surroundings. The eye is only sensitive to light in the wavelength region from about 400 nm to about 700 nm. The maximum sensitivity of the human eye is to light that has a wavelength of about 555 nm. It is important to know how the eye responds to light because if its response is known, it is possible to use a light detector that has almost the same response as the eye. Such a detector can then be used to quantify the visible characteristics of smoke because it responds in the same manner as the human eye. Smoke is visible because it either scatters or attenuates (diminishes) light. In some instances, smoke is visible because the smoke particles reflect light which is then detected by the eye. The eye actually "sees" an intensity of light that has been reflected from a cloud of smoke particles. Imagine shining a flashlight into a cloud of smoke. Someone off to the side can actually "see" the beam of light as it traverses the smoke cloud. This is called scattering. Smoke is also visible be¬cause it attenuates light. Imagine having someone shine a flashlight into your eyes. As smoke begins to build up along the beam of the flashlight, the light begins to dim. The smoke is visible because it is now reducing the intensity of light that falls upon the eye. As the smoke level increases, it is said to obscure our visibility. When the beam is no longer visible, the smoke obscuration is said to be 100%. In other words, none of the light energy from the flashlight makes its way through the cloud of smoke. Another way of saying that the obscuration is 100% is to say that the transmission of light through the cloud is zero.

Jan 1, 2000

By J. Douglas Causey

In 1987, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied 13,374 acres of the 14,994-acre Ireteba Peaks Wilderness Study Area (NV-050-438) in order to evaluate its identified mineral resources. The study area is located in Clark County, NV, about 4 miles south of Nelson, NV. No identified resources were found within the Ireteba Peaks study area, although there are identified subeconomic resources just outside of the study area boundary. Most of the area is underlain by Tertiary granitic rocks, which apparently postdate mineralization. The area is virtually surrounded by mining districts with mines developed in older rock units. On the north side, quartz monzonite, volcanic tuff, and tuffaceous sediments in the Eldorado mining district host deposits of gold, silver, copper, zinc, and mercury. On the south side, Precambrian gneiss, intrusive andesite porphyry, and hornfels in contact with Quartz monzonite in the Searchlight mining district host gold, silver, copper, and lead deposits. The Newberry mining district to the southeast had copper, gold, and silver mineralization in Precambrian gneiss and andesite.

Jan 1, 1988

By R. H. Grau, S. B. Robertson, F. Garcia, A. C. Smith, T. P. Mucho

Researchers working for the National Institute for Occupational Safety and Health (NIOSH) at the Pittsburgh Research Center are developing ways to protect the health of miners. Part of that effort is improving the air quality in metal/nonmetal mines by developing proper ventilation techniques. The air quality of large opening nonmetal mines can be greatly improved by using engineering controls of contaminant prevention and proper ventilation techniques. Contaminant prevention includes methods to reduce contaminants from entering the mine air. Ventilation can be improved with appropriate fan selection and fan operation used in conjunction with air coursing using manmade and insitu rock stoppings.

By Heinz W. Sternberg

The literature on electrochemical treatment of coal is reviewed, and possible avenues of further research in this field are discussed in this report. Electrolytic reduction of finely distributed coal resulted in the addition of as many as 9 atoms of hydrogen to 100 atoms of carbon. Reduction of coal extracts at controlled potentials indicated the presence of condensed aromatic hydrocarbons and reducible quinones in coal. As much as 65 percent of low-rank coal can be made alkali soluble by electrochemical treatment. Higher rank coals gave smaller yields of alkali-soluble products. However, the nature of this reaction is not clear. The difficulty of reducing coal electrolytically is probably due to the insolubility of coal and not to any structural peculiarity. Reduction of coal by electrolytically generated radical anions appears to be a promising approach for further research.

Jan 1, 1962

By D. R. Tesarik

The factor of safety, the traditional measure of stability for earth embankments, is graphically presented in factor of safety charts in this Bureau of Mines report. Factor of safety contours are drawn for homogeneous earth embankments for two contrasting situations: (1) no phreatic surface and (2) a phreatic surface that assumes 10-pct freeboard. The factor of safety can be read directly from the charts if the physical properties of the soil and the geometry of the embankment are known. The curves provide a quick first approximation of the "most stable" and "least stable" condition of the embankment. The Simplified Bishop Method was used for the safety factor calculations, and a sequence of least squares curve fitting steps was used to present the factor of safety in final chart form.

Jan 1, 1981

By E. D. Gardner

The mine of the Eureka Standard Consolidated dining Co. is at Dividend, Utah, in the Tintic mining district. It is operated under the same management and controlled by the Antic Standard Mining Co.; the two properties adjoin each other. The Eureka Standard is worked through a vertical shaft; the ore is mined by a stringer-set-and-fill method. One hundred and thirty men were employed in April 1933. The normal daily tonnage is 100 tons; the ore is shipped to the smelter at Garfield, Utah.

Jan 1, 1935

By W. W. Adams

"During the calendar year 1925 the Bureau of Mines received from the operators of several hundred mines and quarries complete accident records covering deaths, permanent disabilities, and “lost time” temporary injuries. Some of the companies, - those that participated in the National Safety Competition-also furnished information showing the number of man-hours of work performed during the year. With these two types of information it was possible to calculate the accident-frequency and accident-severity rates of the different plants. Complete and comparable reports of accidents and Man-hours of “exposure” were received from 34 underground metal mines, 59 underground coal mines, 15 underground mines producing other nonmetallic minerals, and 102 open quarries or open-pit mines. The figures in the table appended to this report show the accident severity rates and other data for each of the 34 underground metal mines and for the group as a whole. It is proposed to publish similar figures for the other classes of mines and quarries at an early date.The 34 metal mines listed in the table are situated in Arizona, Idaho, Kansas, Michigan, Minnesota, Missouri, New Jersey, New Mexico, Oklahoma, South Dakota., and Utah; they employed 5, 925 men, an average of 174 men per mine, including employees above-ground as well as underground. With but few exceptions, 50 men was the minimum number of employees in any mine. The total period of employment or “exposure” at the 34 mines was 14,612,607 man-hours, an average of 2,466 hours per man, or the equivalent of 308 work-days of eight hours for each employee. Accidents resulted in 15 fatalities, 9 permanent disabilities, and 1,950 temporary “lost time” injuries (causing disability exceeding remainder of shift). The fatal and nonfatal injuries represented 132,575 days of disability. Thus the accident frequency rate for the group was 135 accidents per million hours and the accident severity rate was 9.073 days lost per thousand hours of 1 “exposure”. The severity rates ranged from 0.227 to 88.653, while the ·range of the accident-frequency rates was from 16. 6 to 307 .4. In compiling the accident severity rates shown in the table, all accidents caused by explosives were weighted at twice the number of days actually lost, as one of the purposes of the National Safety Competition was to stress the prevention of accidents caused by explosives."

Sep 1, 1926

By Wilbert J. Huff

The Explosives Division of the United States Bureau of Mines makes certain laboratory and field investigations that deal with explosions, explosives, ignition, and combustion, together with many related problems, such as the cause and prevention of fires, and certain fundamental scientific questions bearing upon the determination of the chemical and physical mechanisms underlying some of the important phenomena encountered. Its work on explosives has been particularly directed toward determination of the chemical and physical characteristics of explosives designed for use in coal mines and in a more limited way to those used in metal mines, tunnels, quarries, and other engineering operations. This testing is handled by two units of the Explosives Division, as follows:

Jan 1, 1937

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

UNIT OF MEASURE ABBREVIATIONS USED IN MFIRE FT foot FT3/MIN cubic foot per minute LBM•MIN2/FT4 pound mass times minutes squared over feet to the fourth FT2/HR square feet per hour BTU/HR*FT*F British thermal unit divided by hours times fimes feet times degree Fahrenheit IN W G inches water gage FT3/MIN cubic feet per minute FT2 square feet FT3 cubic feet LBM, pound mass F Fahrenheit IN W G /CFM2 inches water gage per cubic foot per minute squared PERCENTAGE percent BTU/MIN British thermal unit per minute MFIRE BAT PROGRAM cls echo off echo MFIRE activated mfire0 echo Wait a moment for loading the program if EXIST zheng chg mfirel if EXIST zheng chg mfire2 if EXIST zheng chg mfire1 if EXIST zheng chg erase zheng chg if EXIST hang chg erase hang chg if EXIST yunzhi fan copy yaodong.ion+yunzhi fan yaodong ion if EXIST yunzhi fan erase yunzhi fan if EXIST xintan chg copy yaodong xin+xintan chg yaodong ion if EXIST xintan chg erase xintan chg if EXIST yaodong xin copy yaodong.xin mfire out if EXIST yaodong.xin erase yaodong.xin if EXIST net erase net echo Your output is saved in file MFIRE OUT MFIRE0 FOR PROGRAM CHARACTER•50 A OPEN (10,FILE='NET',STATUS='UNKNOWN',FORM='UNFORMATTED') NETWW=0 WRITE (10) NETWW OPEN (21,FILE='ZHENG CHG',STATUS='UNKNOWN',FORM='UNFORMATTED') A=) ' B=0.0 WRITE (21) A WRITE (21) A,B

Jan 1, 1990

By Manuel Gomez

Primary, low-temperature tars are generally known to alter with time. The effect is believed to occur, in some instances, without the external influence of air, light, or heat. Since one of the processes occurring during extended storage is oxidation, the action of mild oxidation induced by air and heat, in addition to the effect of storage, was studied. The principal effect in aging and oxidation is formation of pitch at the expense of the distillate fraction. The fraction boiling above 270° C. is mainly involved in pitch formation due to storage, whereas all fractions are affected to some degree when tar is heated at 125° C. in the presence of air. If the effects of air are considered, the aromatic and tar-acid fractions seem to be important in pitch formation.

Jan 1, 1956

By H. R. Beard

The Bureau of Mines investigated the absorption of radium and thorium from waste uranium leach liquor by clays and other materials. This work was conducted in support of the Bureau's goal of minimizing the environmental conflicts, impacts, and occupational hazards associated with mining and milling operations. Tailing and soil samples from New Mexico were evaluated for their potential to absorb radium and thorium from tailing liquors. Absorption ranged from 0 to 97 pct for radium and 0 to 60 pct for thorium. Some samples that readily absorbed radium were contacted with various salt solutions that could be present in tailing solutions to determine whether desorption would be a potential problem. The desorption of radium ranged from 0 to 75 pct. An alpha spectrometric method was used to determine the radium and thorium concentrations in the solutions and solids.

Jan 1, 1980

By A. Sainato, S. J. Kravits, G. L. Finfinger

This Bureau of Mines report describes and compares the procedures, capital investments, and operating costs of rotary and in-hole motor drilling techniques used to drain methane gas from the Pittsburgh Coal- bed in an underground mine located in southwestern Pennsylvania. A timestudy was conducted during the drilling of each of two boreholes, and the data were collated to serve as a base for comparing drilling procedures and operating costs. Findings indicate that drilling with an in-hole motor offers four advantages over rotary drilling; namely, an increase in drilling productivity, fewer worker-hours required, ease of maintaining vertical and horizontal bit trajectory, and less expensive drilling cost per foot of borehole.

Jan 1, 1985

By Kenneth L. Cashdollar

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRL Lake Lynn Experimental Mine and after laboratory explosions in the PRL 20-L chamber and the Fike 1-m3 chamber. The dusts studied included both high and low volatile bituminous coals. Low temperature ashing for 24 hr at 515°C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as or higher than the initial incombustible content. The MSHA alcohol coking test-was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared to the initial dust loadings to determine the transport distance of dust during an explosion. All of these data will be useful in future forensic investigations of accidental dust explosions in coal mines or elsewhere. Disclaimer: The findings and conclusions in this report are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health or the Mine Safety and Health Administration.

Jan 1, 2006

By S. H. Brooks

"IntroductionThis preliminary report deals with the effect of oxygen pressure on the ignition temperature and combustibility of oils, it is the third of a series which will present the results of an investigation being made by the Bureau of Mines, on oxygen-oil explosions. The purpose of this research is to obtain technical data that will serve as a basis for safety precautions general outline of the problem has been given in the first report (Serial 2507).The present experiments have resulted in (1) a method for determining spontaneous ignition points of oils in an atmospheric of oxygen under pressure; and (2) the determination of these ignition temperatures for three typical oils, one being an animal oil (sperm), one a vegetable oil (linseed), and one a mineral oil (""Moiloil A"").These experiments on explosibility of oil were performed in order to discover the general nature of the phenomenon, especially the order of magnitude of the temperature necessary for spontaneous explosion (120°C. and upwards) and the effect of pressure variation (negligible as regards ignition temperature but important in relation to the violence of the explosion). A continuation oftests should provide a basis for selecting the safest lubricants for high pressure compression of gases particularly air and oxygen; and should be of value when devising new specifications for lubricants, both in the government departments and the compressed-gas manufacturing industry."

Dec 1, 1923

By R. P. Jewett

The object of this investigation was to correlate the crushing strength of green pellets prepared from magnetite, specular and earthy hematite with the particle size of these respective raw materials. In this study no attempt was made to correlate the strength of fired pellets and particle size. The effect of particle size upon a number of fine ores and concentrates was studied. Much of the low-grade ore reserves in the Lake Superior Region must be finely ground before concentration and then agglomerated for iron and steelmaking processes. Fine natural ores also must be agglomerated. Pellets constitute an important type of agglomerate. Considerable handling occurs during screening to remove undersize and oversize pellets, and in transfering green unfired pellets from the balling machines to the heat-hardening equipment. As a result the strength of the green pellets is a factor of great importance.

Jan 1, 1961

By L. D. Gehi, A. W. Khair, M. Ahmad

"Bit wear presents problems to mining operations because it affects both productivity and economics. Most bit research deals with energy requirements and energy dissipation mechanics for ideal fragmentation during the cutting process.Mechanical cutting leads to dust generation. Past studies involving dust generation due to bit wear concluded that dust concentrations increased considerably after a 7% bit weight loss: leading researchers recommend that the bits be changed at that point.Bit wear is affected by three factors: machine operating parameters in-situ mining conditions and rock properties. Operating parameters such as the depth of cut tool material spray position and the drum's rotating velocity are very important and have a definite impact on bit wear.During the mining process the amount of rock in coal and the strength of that rock is important as abrasion and adhesion take affect. Diffusive wear or deformation becomes dominant only when the temperatures exceed critical. Temperatures rise as a function of drum velocity rock properties and the cutting tool itself.Miner bit surveyIn this study, 15 mines were surveyed, and of those six responded for nine seams. The survey reflected a wide range of information about coal production and bit consumption from continuous miner sections. Also used bits were collected to get first-hand information to analyze wear."

Nov 1, 1995