Search Documents

By Roy T. Sorensen

As part of its mission to maintain an adequate supply of minerals to meet national needs and maximize mineral production from domestic sources, the Bureau of Mines is investigating the recovery of alumina by hydrochloric acid leaching of kaolinitic clay. Most iron impurities are leached from the clay along with the alumina and must be removed before or during crystallization to aluminum chloride hexahydrate. The thermal decomposition step then provides an alumina product of acceptable iron analysis. Miniplant studies of a Bureau-developed solvent extraction technique, using a tertiary amine in kerosene diluent, have demonstrated that the iron content in aluminum chloride leach liquors can be reduced to levels of less than 0.007 wt-pct (7 ppm), expressed as Fe203. Entrained and dissolved organic matter in the purified pregnant leach liquor from the solvent extraction circuit can be reduced to less than 2 ppm by using a fabric-packed coalescer and subsequent activated carbon treatment. Investigators discovered that a steady buildup of zinc accumulated in the solvent phase within the extraction circuit, proportional to the amount of leach liquor treated. The solvent phase zinc analysis increased by 0.01 wt-pct ZnO for each 1,000 gal of pregnant leach liquor purified.

Jan 1, 1981

By S. H. Lorain

This paper is one of a series being published by the Bureau of Mines describing the mines and mills and subjects related to mining in western mineral areas. Although mining districts in the Tobacco Root Mountains are numerous there is a strong similarity in the character of the ore deposits and in the climatic and economic conditions affecting mining throughout the region. Individual mines are small, but the production of lode mines

Jan 1, 1937

By P. D. Lohn

The objective of this program was to develop nozzle designs to maximize the effective cutting length of a water jet. The results of the theoretical program directly support the Bureau of Mines Borehole Mining Program and their experimental program to improve the rock cutting capability of water jets. The borehole geometry requires turning the flow by 90 degrees and accelerating through the nozzle within a restricted length. Several suggestions for turning the flow are offered. The borehole space limitations constrain nozzle length, to the extent that a standard 13-degree tapered nozzle (6-1/2 degrees half angle) is too long to fit in the borehole, at production flow conditions. The design technique developed is computationally economical and enables examination of a large number of shapes and flow conditions. The nozzle design is based on design criteria of minimization of boundary layer thickness at the nozzle exit and minimization of the possibility of separation and cavitation. Six flow conditions, including pressures to 4500 psi and flow rates to 400 gpm, were examined, Best shapes were determined for all flow conditions. The best shape for a borehole reining application consists of an initial 4th degree polynominal (quartic) at the entrance followed by a straight section with a twenty degree (half-angle) taper at the exit.

Jan 1, 1976

By J. H. Adkins

The goal of this program was to produce a set of baseline health and safety training materials that could be used by the metal/nonmetal mining industry to reduce injuries and to comply with federal training requirements. The materials developed are arranged in a two level outline format. The first level provides the title, course goals, background and topical outline while the second level provides a detailed outline of the course content. Visuals, designed to portray miners in a positive, attractive fashion, were done in simple line drawing so they would reproduce for handouts without loss of quality. Each of the required units in the Baseline Guides have one or more self-checks. These are designed to be suggestive of evaluation techniques the users can develop for themselves. An instructors guide and a mining terms glossary are included. In a second phase the program developed performance based training guides for Annual Retraining and Experienced New Hires in the Underground Salt Industry.

Jan 1, 1983

Protect mine rescuers from heat-induced stress that drastically cuts their endurance and saps their strength. Approach To prevent exhaustion caused by thermal stress, a rescuer can wear a liquid-cooled hood and vest which absorbs heat, thereby reducing the heat-induced strain on the rescuer's heart and circulatory system. How It Works Liquid coolant is continuously circulated through a self-contained system in which the coolant is chilled by a heat sink on the wearer's belt. The coolant, which is a mixture of alcohol and water, is pumped from the heat sink to bladders inside the hood and vest where it absorbs body heat. After absorbing heat In the hood and vest areas, the coolant returns to the heat sink where it is rechilled by passing through a tube coiled around a steel can containing a block of ice. To adjust the temperature of coolant leaving the heat sink unit, a valve can be operated by the wearer, causing part of the flow to bypass the coil. A small pump and a rechargeable battery are also part of the assembly.

Jan 1, 1979

By Charles Prasky

This report describes fluidized bed techniques employed by the Bureau of Mines at Minneapolis to differentially sulfatize the manganese in two samples of low-grade manganiferous ferruginous carbonate slates from the Cuyuna Range district, Minn. Suitable mechanics of operation were established. A space rate of 1.25 to 1.5 fps, a retention time of 3 to 3.5 hours, a temperature of 700° C, and a 10 percent sulfur dioxide gas in air were adequate for sulfatizing the slates by fluidization. Under these conditions the overflow product removal rate from the 4-inch-diameter reactor was 4 to 5 pounds per hour. The sulfur dioxide was used more efficiently in the two-stage treatment than in the single-stage treatment. However, approximately 80 percent of the manganese was converted to sulfate by either treatment.

Jan 1, 1963

By C. K. Eilerts

Knowledge of the phase relations of the fluids that exist in the porous spaces of rocks constituting natural petroleum reservoirs and of the behavior of these fluids under various field conditions of operation is essential to the conservation of petroleum and natural gas and to their efficient recovery. The problem of determining whether these fluids axe in the liquid or gaseous state send of recognizing the transitions that may take place as the material in the reservoir is subjected to different conditions of pressure and temperature confronts many producers today, especially in certain fields. The subject has grown rapidly in importance since the discovery of and production from deeper reservoirs that have correspondingly higher pressures rind temperatures as compared with shallower

Jan 1, 1938

By Raymond B. Ladoo

Garnets are usually found well crystallized in the cubic system , the principal forms being rhombic dodecahedrons , tetragonal trisoctahedrons or combinations of the two , and hexoctahedrons . They also occur as rounded disseminated glassy grains and in compact massive , laminated or gramlar aggregates . They vary greatly in color , but the most common garnets , almandite and andradite , are most often found of a dark red or reddish brown color .

Apr 1, 1922

By Joseph M. Singer

This research project had two main objectives: (1) To identify the smoke limits of gaseous fuel-air mixtures and (2) to obtain and evaluate basic chemical information on the formation of smoke in very rich flames near the smoke limit. Such information would do much to establish the circumstances for car-bon deposition in gas appliances and in other types of combustors. Based on tests with ethylene and propane, these studies showed the following: 1. Smoke limits are related to the yellow-tip limits of the fuel. Previous research established sufficient data to permit prediction of yellow-tip limits on gas burners using a wide variety of fuels. The present study of smoke limits deals only with ethylene-air flames, but the concept that was developed is probably applicable to other fuels.

Jan 1, 1962

By G. W. Jones

As part of its program for the promotion of safety, the Bureau of Mines has investigated various means of mitigating or eliminating the explosion hazards of combustible gases and vapors found in the mining and other industries. Knowledge as to the explosive characteristics of cyclopropane in air, oxygen, and other gaseous mixtures is of both theoretical and practical importance because cyclopropane is now used extensively in anesthesia. As such an agent it has many desirable characteristics, and increased consumption of this gas may be expected if the explosion hazards now attending its use can be minimized or eliminated. The present practice of using mixtures of approximately 20 percent cyclopropane and 80 percent oxygen should be discouraged because such mixtures are violently explosive and have led ,to fatal accidents.

Jan 1, 1940

By G. W. Jones

As part of its program for the promotion of safety, the Bureau of Mines has investigated various means of mitigating or eliminating the explosion hazards of combustible gases and vapors found in the mining and other industries. Knowledge as to the explosive characteristics of cyclopropane in air, oxygen, and other gaseous mixtures is of both theoretical and practical importance because cyclopropane is now used extensively in anesthesia. As such an agent it has many desirable characteristics, and increased consumption of this gas may be expected if the explosion hazards now attending its use can be minimized or eliminated. The present practice of using mixtures of approximately 20 percent cyclopropane and SO percent oxygen should be discouraged because such mixtures are violently explosive and have led to fatal accidents.

Jan 1, 1940

By Richard A. Dick

Eight blasts were fired in a 2-1/2-ft bench in the Stewartville member of the Galena Limestone formation in an aggregate quarry near Stewartville, Minn. The shots were dimensionally proportional to production-size bench blasts and were about 5 to 10 percent of full scale. The effects of site, timing of initiation, and burden-to-spacing ratio were studied in a 2 x 2 x 2 factorial experiment, using three boreholes, caw;, containing a 1/2-in charge diameter of high-density ammonia dynamite, in each blast. Detonation velocity measurements indicated that the dynamite detonated satisfactorily in the 1/2-in charge diameter. The effects of the three experimental variables were analyzed by weight for the percentage of oversized material produced and for size distributions determined by screening the entire muckpiles. The bench faces were painted before each shot in an effort to determine the origin of the oversized material. The square pattern (burden and spacing = 15 in) produced finer overall fragmentation and less oversized material than the rectangular pattern (burden = 15 in; spacing = 22-1/2 in). Sites 1 and 2 were about ft apart. Although site 2 produced slightly better overall fragmentation than site 1, the amounts of oversized material produced showed no significant difference. The timing of initiation (instantaneous or delayed) did not significantly influence the overall fragmentation or the amount of oversized material produced.

Jan 1, 1973

The Objective: To reduce the noise generated by the exhausting air from a pneumatic roof bolting drill to a maximum of 90 decibels. Any attachment used for this purpose must be lightweight and must not cause a significant increase in back pressure. The Approach: Absorb the noise with a properly designed muffler that will permit sufficient airflow without affecting the normal operation of the drill. How It Works: The air exhausted by the drill enters the muffler through perforated disks into a resonator chamber. It then passes through a series of expansion and contraction chambers and is expelled to the atmosphere through another perforated disk. The basic muffler design for the pneumatic drill was established by using both digital computer analysis and experimentally simulated noise tests. The measured parameters used in the computer program consisted of inlet and outlet pressures, temperatures, airflows and exhaust areas. United

By Edward L. McHugh

The study area, which comprises 28,443 acres within the Jacumba Wilderness Study Area, is in the California Desert Conservation Area, and along the U.S.-Mexico border 25 miles west of Fl Centro, CA. The U.S. Bureau of Mines evaluation of mineral resources is based on examination of mining claims, known mineral occurrences, and mineralized zones during the fall of 1983. Limestone resources were identified inside the study area; tungsten resources may he present. Metasedimentary rocks intruded by Cretaceous Quartz diorite predominate in the study area. Tungsten and some gold have been found in skarn zones along intrusive contacts; limestone deposits are in the pre-Cretaceous rocks. Tertiary and Quaternary volcanic flows, pyroclastic rocks, clay beds, and diatomite in lake deposits nave been investigated for possible non-metallic resources. Evidence of mining or prospecting was found at 26 sites in or just outside the study area. In 1983, 106 claims were held in 13 claim groups. One claimant was sporadically prospecting for gold on claims in the north part of the study area in 1983, and gravel was being mined from alluvium 1/4 mile to the east.

Jan 1, 1985

By O. W. Owings

"The handling and transportation of explosives and explosives supplies are inherently hazardous owing to their sensitiveness to impact and flame or electric arcs and sparks. Many accidents have occurred in the past during transportation of explosives, especially when they were carried by individual miners on man-trips. When electric haulage became the usual mode of transportation and shots were fired electrically, the hazards of carrying explosives and supplies on man-trips were fully realized, and in some mines all explosives were placed in one car, usually at the rear of the trip. Far-sighted managers saw the danger of this practice and provided separate trips for delivering explosives. This step was a definite advance in safety, but the latest achievement is the construction of special, rugged, nonconducting cars.Many coal-mining men have shown considerable interest in the construction of safe cars for explosives during recent months. Undoubtedly many others are interested in this phase of safety, therefore this circular is issued to give information on cars of this type now in use.Car A (fig. 1) is essentially a closed inner box separated from an outer box by an insulating lining of rubber. The double box is attached to a standard steel chassis that has spring journals and electric welding instead of certain rivets. The chassis is equipped with roller bearings. The over-all length from pin to pin is 11 feet, 9 inches; the wheel base is 54 inches, the track gage 42 inches, and the capacity eighteen 50-pound cases of permissible explosives. The box is 10 feet long, 6 feet wide, 3 feet high at the top of the arched roof, and 2 feet 9 inches at the edges. The top of the car is 46 inches above the top of the rail.The inner box is insulated from the outer box by two pieces of 1/4-inch switchboard.-insulating matting cemented together. To cover the top, two ends, two sides, and the bottom of the box requires 320 square feet of the l/4- inch matting.The walls are well-seasoned tongue-and-groove oak, 1 1/4 inches thick and 2 3/4 inches wide. A 1 1/4-inch air space is maintained by oak strips between the outer wall and the two thicknesses of 1/4-inch rubber matting. The inner box is made of 7/8-inch, well-seasoned, tongue-and groove oak fitted closely against the insulating matting. No nail, rivet, or bolt extends through the rubber insulation.The floor of the outer box is secured to the chassis by two sets of bolts through an intermediate piece of well-seasoned oak. One set of bolts is countersunk from the top of the intermediate piece of oak, and the other set is countersunk from the bottom. The countersunk portions are filled with ""insulate,"" an insulating compound. Adjacent bolts are at least 6 inches apart.The bed of the inner box is divided into six compartments by transverse strips of wood at the bottom and partitions near the roof. Each compartment accommodates three 50-pound cases of explosives. This arrangement prevents cases in adjacent compartments from touching, so that there is no possibility of end thrust of the entire load of explosives. Each inner compartment is 21 inches high, 5g inches long, and 16 1/4 inches wide. Separating strips at the floor are 3 inches wide and 1 1/4 inches thick. The outside dimensions of the 50-pound cases of explosives used are 17 1/2 inches long, 13 1/2 inches wide, and 12 1/2 inches high."

May 1, 1940

By Martin Smirlock

A novel instrumentation system has been developed which enables simple, quick, and accurate measurement of vehicular dynamics within low speed ranges. The system, consisting of a microwave transceiver and microprocessor data acquisition and reduction system, measures the deceleration dynamics of low-speed mining and construction equipment. It makes the basic measurement, calculates key parameters such as average deceleration, initial velocity, stopping distance, and brake system delay time, and produces autoscaled graphs of velocity, acceleration, and displacement versus time.

Jan 1, 1981

By W. F. Watts

This report describes the Mine Inspection Data Analysis System (MIDAS) developed by the Bureau of Mines to analyze the records of industrial hygiene samples collected by the Mine Safety and Health Administration (MSHA) in metal and nonmetal mines. MIDAS is the first system capable of sorting, editing, analyzing, and reporting these data. It is also the first system designed to be used by a number of Government agencies. At present the system contains 225,000 personal and area samples for 61 contaminants in 45 industries. The records date from 1974 to early 1980, and MSHA plans to provide yearly updates to the system. This report presents preliminary analyses of dust exposures and discusses the potential uses and limitations of these data. Analysis of the dust data for 1978 and 1979 showed that bagging had the highest percentage of dust overexposure. Morn than 40 pct of the 1,536 respirable quartz dust, total nuisance dust, and total silica dust samples exceeded the MSHA exposure limit. Other dusty occupations are ranked according to their percentage of overexposure.

Jan 1, 1981

By William F. Keyes

Greensand, which is widely distributed in the Eastern United States, was produced in 1975 only by Inversand Co., a subsidiary of Hungerford & Terry, Inc., near Clayton, N.J. Production and sales information are not available for publication. Raw greensand produced by the company was sold for agricultural use as a soil conditioner. Processed greensand was used by manufacturers as filter media in equipment for the removal of manganese, iron and other elements from water. The University of Delaware received a grant of $17,051 from the Bureau of Mines early in 1976 to continue its studies of the effectiveness of greensand in removing metallic contaminants from waste waters.

Jan 1, 1977

By John D. Warne

"INTRODUCTION Initiated as a part of the Bureau of Mines program for development of strategic minerals for national defense, Investigation of the fluorspar deposits of the Northgate area was begun in June 1944 and completed in March l946. Mining Operations were active in the district during most of the period of investigation.The Fluorspar, Fluorine, and Camp Creek mines develop the two more promising vein systems known in the area, the Fluorspar group of claims covering one vein system and the Fluorine and Camp Creek groups the other. Figure 1 shows the location of the properties. The Fluorspar and Fluorine properties were operated (except during the winter months) by the Western Fluorspar Corp. The Camp Creek mine was operated during 1943 and 1944 by Kramer Mines, Inc.The properties were examined April 20 and again November 4 to 12, 1943, by C. R. Wilfley, a Bureau of Mines engineer, who recommended work to determine ore reserves and to serve as a guide for development. Investigations by the Bureau of Mines covered all three properties."

Aug 1, 1947

By W. H. Coghill

Numerous investigators have studied grinding. Each has contributed his bit to a literature that is difficult to correlate. Too many of the results have been transformed into curves with so many "inflection points" and "counterflexures" that they obscure the issue. Some of the investigators have neglected the very essence of the problem, namely the power and the amount of material to which a known amount of work was applied. The purpose of this paper is to show the ease with which results can be interpreted when these quantities are duly recognized. Some grinding tests will be given for illustration. Grinding studies are of two kinds: (1) Study of the character of the ore and (2) study of the performance of the machines. Several ores may be crushed by a given machine, or several machines may be used on a given ore. The illustrations given in this report cover both objectives.

Jan 1, 1934