Search Documents

By Mark D. Kirkbride

This paper outlines the process for designing a hard rock blast in an underground coal mine. The coal mine is located in Western Kentucky and operates four continuous miner units at 7 unit-shifts per day. The mine operates in the Western Kentucky No. 11 Seam with local variations from 4.5 - 5.5 feet seam thickness. The seam has sporadic siderite deposits. Usually these deposits do not significantly interfere with the mining process. When previous siderite deposits were encountered they were small enough to drop an entry for a couple of crosscuts. The blasting plan was called for after a siderite deposit was encountered in the belt entry at about one third of the panel length. The other sides of the panel had been previously mined and sealed so the decision was made to mine through the siderite deposit with the continuous miner instead of abandoning the panel. The deposit was approximately 300 feet in length down the belt entry. Mining through the deposit with the continuous miner was expensive in both terms of production and of wear and tear on the continuous miner. A blasting plan for the siderite deposits was designed to minimize damage to the continuous miner should a similar situation occur.

Jan 1, 1999

Blasting is a very cost effective method of rock fragmentation but its uncontrolled application often results in excessive damage to the perimeter of an excavation. Several perimeter control techniques are available but tracer blasting is commonly used in Canadian underground mines for overbreak control. This involves tracing a column of Ammonium Nitrate-Fuel Oil (ANFO) with a detonating cord. In order to investigate the techno-economic effectiveness of tracer blasting in perimeter control, a field experimentation was conducted which involved blasting in sublevel caving and sublevel sloping operations, experimental drifting, benching and pipe tests.

Jan 1, 1997

Almost one half of Canada's total land surface is underlain by permafrost. This term describes the thermal condition of earth materials when their temperature remains below 0°C continuously for a number of years. The drilling and blasting of frozen materials requires more energy than the blasting of same in its unfrozen state. The cost of comminution could double in permafrost even with adequate organization, drilling equipment and proper explosives.

Jan 1, 1975

By Lon D. Santis

This paper reports on an evaluation of the safety characteristics of short lead, 5 centimeter (cm), Magnadet1 detonators. The Magnadet initiation system uses magnetic induction principles to transfer electric energy from the firing line to the detonator without a physical connection. This study was initiated because the Magnadet initiation system represents a new technology and the Bureau is interested in ensuring that no potential safety hazards are introduced into the nation's mining environment. The Magnadet system and its proper use are described along with a discussion of how it works. The potential hazards examined are: stray current from mine service power, lightning, DC current, static electricity, and radio frequency transmissions. Tip strength is also evaluated. Experiments were conducted to evaluate some hazards and theoretical methods were used to evaluate others. The results showed that the Magnadet short lead initiation system does not exhibit any unusual safety hazards. The new system is at least six times as resistant to common hazards as currently used electric initiation systems, so long as the insulation is intact.

Jan 1, 1992

By Quian Liu

The problem of cross-hole explosive malfunctioning in rock blasting (including sympathetic detonation, desensitization and cut-offs) is a function of delay and spacing in a blast which should be designed to avoid such occurrences. On a delay-spacing chart, the phenomenon of explosive malfunctioning is explained by dividing the chart into different regions, while the shape and size of each region could vary from one explosive to the other. Over seventy blasts have been carried out at the CANMET Experimental Mine to identify the malfunctioning characteristics of specific emulsion, water-gel and dynamite explosives. In each experiment, two parallel blastholes, 32 mm in diameter and 1.7 m deep, were drilled downwards in an underground drift.

Jan 1, 1994

By C Hunter, K Fedak, J P. Todoeschuck

"Perimeter wall control has a direct effect on the overall grade of any underground miningoperation. Mine management at INCO's Birchtree Mine in Thompson, Manitoba requiresmaximum perimeter wall control to meet high safety standards and to maximize nickel orerecovery. If footwall or hanging wall contacts are damaged by over_blasting, the ore maybe greatly diluted, mine productivity may be reduced and safety problems can arise.Excessive or poorly distributed explosive energy is a major cause of damage to the hostwall rock."

Jan 1, 1993

By Eduardo Berger

This paper describes a mechanized loading system, the HYDRODOSE, which allows the use of pumpable emulsions in underground mining. It also describes a pumpable emulsion explosive for small diameter holes, HYDROMITE PDB. Included are test results carried out in two Chilean underground mines.

Jan 1, 1991

By Joseph Meyers

Explosives techniques and technology are constantly evolving and improving, yet basic communication and business skills are not being used regularly. Many potential blasting projects never occur due to simplistic, basic factors, such as a lack of communication. Articulate communication is the key component in the blast approval process, which has changed remarkably from how business was conducted fifty years ago. Imperative to the approval process is communication outlining the safety and benefits of the blasting project. Information and transparency with the stakeholders and the Authority Having Jurisdiction (AHJ) will greatly improve the chances of having a blasting project approved. This open communication starts at the inception of the project when the memorandum of understanding (MOU) is obtained, and involves the AHJ through all steps of the approval process. The blasting industry and regulators must work collaboratively to improve safety, security, regulations and licensing. Implementing state of the art blasting techniques, security, safety measures, vibration monitoring and strict licensing allows the AHJ and all stakeholders to remain integrated and informed, contributing to process approval. Regulatory operators should strive to achieve success thru communication, cooperation and compliance which is accomplished thru continued education and transparency. These steps, combined with regular meetings, has proven to be a benefit to both industry and regulators. Relationships are built through trust, teamwork, transparency and communication –including the take holders and AHJ in the approval process from the inception solidifies these relationships and improves teamwork

By Frank Hirthammer

"Nowadays, security in the lifecycle of explosives is more important than ever. Terror attacks all over theworld pushed the EU to decree a Commission Directive for the identification and traceability of explosives that set a series of requirements for involved manufacturers, distributors and end-users. The challenge was to find and implement a track and trace system for all concerned European companies byApril 5, 2015. Since then, countries worldwide have followed this example and implemented similarregulations."

Jan 1, 2017

By J. Sigler

A series of small scale tests have been performed to establish the effect of powder factor and initiation timing on the grindability of rocks. The blasts were performed in high quality granite blocks, which were cut from stone prepared by dimensional stone quarry operations. Three different types of granite were tested. The charge configurations included detonating cord placed in five holes with water as a coupling medium or concentrated charges of equal mass, placed in the same number of holes, fully stemmed or air decked. The powder factor was varied from 0.4 to 1.2 kg/m3. Typically all charges were detonated simultaneously; however, in some experiments, detonation waves collided in the middle of each borehole and in others a small delay was used between charges. All fragments were collected and screened, and drop weight impact tests were performed on selected size fractions, using different impact energy, to calculate the resistance of the rock to impact breakage. The work index of some of the blasted samples was measured using a standard Bond mill arrangement. The experiments generally showed increased softening of the rock with powder factor, which appeared to be the dominant factor. Charge configuration as well as in-hole collisions of detonation waves affected the initial fragmentation but had little effect on the impact breakage of the samples.

Jan 1, 2008

By Steven P. Case

To meet salt production needs over the remaining life of the Cayuga Mine at Lansing, New York, the Salt Division of Cargill, Inc. decided to build a new underground screening plant. The new plant required a chamber 50 feet wide by 250 feet long and nearly 70 feet high. On advise of their mining contractor, Dynatec Mining Company, the company chose an ingenious excavation method similar to sublevel stoping. This method eliminated the need for an access ramp, reduced equipment needs and excavation time substantially.

Jan 1, 1996

By Koichi Kurokawa, Takeo Ueda, Masahi Nakano, Yoji Tasaki

A lightning strike generates several 10kA and several billion volts, and earth currents generated by lightning is dangerous to some underground and all surface blasting operations. In order to evaluate the safety against lightning in conventional electric firing method and electromagnetic induction blasting system, a test is conducted by connecting a wire with an impulse generator. Frequency of impulse current used in the test is 17kHz and the waveform is a vibration type and the duration time is 250 ~usec. The results of the test show that induced current increases with the increasing of impulse current. In the case of MBS connection, when maximum primary current is 1700A, Maximum secondary current is 11.8A and the electric detonator is fired at this condition.

Jan 1, 1988

By FM Murray

SAFEX International is a global organisation with more than 85 members, all of whom are manufacturers of explosives. On joining each member signs a declaration saying that they are willing to exchange information with regard to any accidents or near misses they may have in order to prevent the recurrence of the incident. SAFEX International was formed 50 years ago in Europe and has now built up a database of more than 700 accidents in the explosives business. Once every three years, an International Congress is held in which members address specific safety themes associated with the explosives industry, and also give details of "what went wrong?", "why?", and lessons learned. The next Congress will be held in Amsterdam between the 29th May and the 1st June 2002. This paper describes the operation of SAFEX International, which is dedicated to the international exchange of experience on industry connected accidents of the explosives business.

Jan 1, 2002

By John C. Brulia

PowerAN is a tradename of Atlas Powder Company for a new line of explosive products comprising blends of emulsion and ANFO in a variety of bulk and packaged grades. The bulk PowerAN grades are either augered or pumped depending upon emulsion content. Augered PowerAN blends contain up to 60% emulsion. Pumped PowerAN grades have an emulsion content of 75% or higher. The blending of PowerAN is usually accomplished at the borehole to satisfy specific borehole conditions. Packaged PowerAN grades are produced in several types of mix plants in diameters of 4" and greater. PowerAN 300 (30% emulsion) and PowerAN 500 (50% emulsion) are the two most popular grades and their chief application is as an economical, high energy replacement for ANFO HD in wet holes. PowerAN combines the cost effectiveness of ANFO with the high performance of emulsions, permitting the blasting engineer to strike an optimum balance between drill pattern expansion and increased productivity according to need.

Jan 1, 1985

By Craig Wilbour, John Stimberis, Rob Gibson, Lee Redden

Active avalanche control is the intentional triggering of avalanches while people are kept out of the hazard area. Explosives are frequently the most effective tool for triggering avalances. In a highway setting an avalanche control program will reduce total highway closure time, while providing greater safety to motorists and maintenance personnel. Avalanche control with explosives is effective when the snow is somewhat unstable and almost ready to slide naturally. Forecasting this condition involves having a network of local meteorological stations, examining snow structure, using mountain weather forecasts, doing snow strength tests, and having the results of ski and explosive tests. The method of delivery of explosives to an avalanche starting zone is governed by the accessibility of the starting zone. Common methods include; hand placing or throwing charges, remote delivery cableways, or "trams", surplus military weapons, and a compressed gas charge launcher, or "Avalauncher". Charges dropped from helicopters are also occasionally use. We have increased the effectiveness of our program by use of large elevated charges. Efforts are being made around the world to develop and utilize better methods for the safe, remote initiation, but procedures have varied dramatically between individual control programs. There is now a movement to review and standardize operational guidelines for avalanche control. Highway avalanche control is often done at night, during winter mountain storms. Heavy rain or snow, high winds, and high avalanche hazard, are common work site conditions. Commercial and economic pressures are increading, so methods that redice highway closure time are important. There are also many safety issues to be addressed in avalanche control work.

Jan 1, 2002

By R H. Stevenson

This paper deals with a new variation of the cast blasting technique, where-in the object is to cast the economic deposit out front under the overburden, while avoiding dilution from the floor material. To date, the technique has been successfully applied at two cement quarries in Iowa and at a granite quarry in Minnesota.

Jan 1, 1991

By Edward J. Walter

Our modern technology is provided with a unique but flexible power tool in the use of explosives. A by-product of explosives usage is vibration or elastic deformation of the earth which is annoying to the ordinary person and can be damaging to structures. The problem is not new, it is more than fifty years old. Adequate vibration standards have been developed so that blasting programs can be properly planned and safely executed. Changes in our social culture have somewhat changed the emphasis in blasting vibration from damage considerations to the much lower level of citizen annoyance. Vibration codes based on this level will be highly restrictive and prohibitively costly. Cooperation is urged between operators, community officials, agencies at all levels,and consultants to see to the development of sound realistic vibration codes.

Jan 1, 1975

By Mauro Fornaro, Marilena Cardu, Renato Mancini

Detonating cord cutting is widespread in dimension stone extraction, especially in the case of hard, abrasive stones as granites, an important resource for Italian industry. General data on this production sector are briefly discussed and analyzed in the first part of the paper. The theoretical basis of operation are summarized, and compared to data obtained from selected commercial cases, in the second part.

Jan 1, 1994

By Q Liu, P D. Katsabanis

The energy output of crushed AN/FO, crushed AN/FO mixed with Aluminum (5%, 6.4% and 9.4% A1 by mass) and a commercial emulsion explosive has been measured using a detonation calorimeter. The charges had a diameter of 10 mm and were heavily confined by a 11 mm thick copper shell. In order to achieve stable detonation glass microballoons were used in the explosives so that the density of the AN/FO charges would be around 1.1 g/cc. The charges were detonated in vacuum and the detonation products were analyzed using gas chromatography. It was found that energy values were very close to calculated values obtained by ideal detonation codes.

Jan 1, 1993

By Steve Dillingham

In recent years, there has been a trend toward increasingly demanding blasting standards being enacted by local and regional regulatory authorities. The objective of this paper is to alert blasters of the difficulties that are created for blasting projects as a result of these restrictions, as well as the steps that can be taken to minimize future conflicts.

Jan 1, 1995