Search Documents

By Jan Rosenkranz, Anders Sand, Lisa Malm, Nils-Johan Bolin

Within flotation technology the general trend is towards very large cells. Scale-up is usually done by postulating geometrical similarity, which implies keeping the aspect ratio constant when increasing cell volume. Consequently, the design of flotation circuits typically involves several cells of identical geometry within a bank. Using a few standard sizes in a flotation plant simplifies design, manufacturing and maintenance of the cells, but does not necessarily guarantee optimal performance and selectivity of the flotation process. Geometry parameters for a given cell volume that influence flotation cell performance include cell height, which causes changes in the hydrostatic pressure and suspension hydrodynamics, and also influences the travel distance of particle-bubble agglomerates as well as the homogeneity of the mixing. Also the thickness of the froth layer depends on the aspect ratio of the cell. The objective of this work is to gain a better understanding of material distribution and properties within a flotation cell and, based on this information, elucidate how alterations of the cell geometry can influence separation efficiency. For this purpose systematic measurements and analyses of the spatial distribution of the different phases within a 160 m3 flotation cell have been carried out with a particular focus on an industrial, low-grade copper ore beneficiation process. The concepts for sampling at different vertical and lateral positions of the flotation cell are introduced. The results from the experimental work give an understanding of internal material distribution within flotation cells. Based on the measured phase distribution and concentrations as well as particle properties at various positions within the cell, the implications for an optimized scaling and design of individual flotation cells within a flotation circuit are discussed.

Jan 1, 2016

By Bruce C. Smart

"Very little attention was given to the regulation of uranium mills by the Atomic Energy Control Board prior to 1974. The ore grade treated by Canadian mills in the past was in the order of 0.08 - 0.3% U and it was not difficult to keep the exposure of workers well below regulatory limits. Furthermore, uranium milling has also been substantially free of occupational illness because environmental control has been generally satisfactory (l).The discovery of higher grade ore bodies in Canada has resulted in higher radiation levels in one mill and this has partly contributed to a need for increased radiation monitoring in the mill. In addition, as greater insight is gained on the effects of radiation, the implementation of the ALARA principle is being stressed at all mills.The concept of ALARA was emphasized by the ICRP (International Committee for Radiological Protection) in 1977 and stands for '""as low as reasonably achievable'"". It is based on the premise that no proven threshold for potential effects of radiation exists and that the actual individual exposure should therefore be kept as far below the regulatory limit as possible, economic and social factors being taken into account."

Jan 1, 1982

By D. Saramak, Z. Naziemiec

"Chalcedonite is an unique rock due to the relatively small area of its occurrence. It also possesses multi-raw-material features therefore it should be given a special protection aiming at its complete and optimal utilization. It is the natural sedimentary rock and the only mine in Poland, located in Inowlodz, where the opencast mining from “Teofilow” deposit is carried out.Chalcedonite mainly consists of cryptocrystalline and microcrystalline chalcedony together with small amounts of autogenous and detrital quartz. The chalcedony itself is a fairy common mineral and many forms of its occurrence is known, some of them are semi-precious minerals. Among the most popular ones following can be found: agate, bloodstone, onyx, carnelian, chrysoprase. Many countries own chalcedony deposits: Australia, Brazil, India, Canada, Namibia Russia, South Africa. However chalcedony in its pure form does not occur in the mentioned chalcedonite rock. The pores, which take usually from 5% to 25% of volume and have sizes smaller than 0.5 mm, are the characteristic feature of all chalcedonite forms. The paper presents some crucial problems of its processing together with most significant directions of its applications. New method of chalcedonite enrichment based on densimetric separation (patented in Poland) is presented. Results of investigation show that the obtained products can increase quality of concrete and filter grits."

Jan 1, 2016

By J. Vanderlaan

A proposed method of applying high-speed, non-destructive part scanning technologies to the production process of UO2 (Uranium Dioxide) fuel pellets is presented. The scanning process examines each pellet individually for correct surface roughness and any surface imperfection or defects. Using optical scanning methods, which consist of laser and CCD camera technology, the complete circumferential surface of the pellet is examined to meet the reactor fuel bundle specifications.

Aug 1, 2010

By Jorge Loredo, Jesús Garía Iglesias

"Abstract - The Asturian fluorspar district consists of vein and stratiform deposits where mineralization is controlled by a combination of lithological and tectonic factors.It is postulated that these fluorspar deposits have been formed under disequilibrium conditions created during circulation of ascending hydrothermal solutions along faults and other high permeability conduits. Mixing of solutions is inferred from fluid inclusion studies. Cavity filing and replacement processes are very important in localizing the ore deposits and in determining their morphology.Permian volcanic rocks in the area yield a regional positive geochemical anomaly in fluorine implying that Permian vulcanism may be a possible primary source of fluorine.On a regional scale a relationship can be established between some of the ore deposits and important tectonic lineaments. The stratiform deposits preferentially occur within a calcareous-detrital facies located at the margins of basins. These basin margins are related to important synsedimentaryfaults.Fluorite is the only economic mineral in these deposits. Quartz, carbonates, barite and pyrite are comnmon minerals accompanying fluorite. Other minerals that may occasionally be present as minor components are: marcasite, chalcopyrite, fahlore, sphalerite, galena and related supergene minerals."

Jan 1, 1994

By G. J. Desroches, E. Ozberk, M. J. Collins, B. D. Krysa, I. M. Masters

The zinc refinery of Hudson Bay Mining and Smelting Co., Ltd. went through a major modernization in 1993, when the roaster and the calcine and fume leach circuits were replaced by a new Sherritt zinc pressure leach plant. The HBMS plant, in Flin Ron, Manitoba, represents the first commercial application of the Sherritt two-stage zinc pressure leach process, with /00% of the zinc concentrate feed processed in autoclaves. The process design of the new plant required definition of the deportments of elements such as antimony, arsenic, chlorine, cobalt, fluorine, germanium, magnesium, manganese, selenium, tellurium and thallium. This paper describes the deportment of these elements in the commercial zinc plant during the first nine months of pressure leach operation, and compares these results with operations prior to the introduction of pressure leaching, and with the results of tests carried out in the She"itt laboratory during the process development phase.

Jan 1, 1995

By T. Krumins, L. Zunti, R. Frischmuth

Titanium and titanium alloys are commonly selected for pressure oxidation autoclave vent piping and pressure control valve components, as well as autoclave internals, in high-temperature operations. In a vent application, titanium ignition risk is reduced by limiting oxygen concentration, and preventing high gas velocity gas impingement on surfaces. Oxygen concentration is dependent on the autoclave pressure and temperature conditions and therefore titanium ignition risk is dependent on standard operating procedures, and process control interlocks and permissive conditions. It is not uncommon for standard controls to be deficient during atypical operating conditions, or for operations to deviate from the operating procedures, increasing the potential for titanium ignition incident. Titanium ignition risk caused by elevated oxygen concentration in autoclave vent systems can be reduced with the introduction of an online autoclave overpressure calculation and the configuration of associated interlocks and permissive conditions.

Jan 1, 2014

By K. Purazrang, P. Sh. Naseri, P. Abachi

In present work, the comparative measurement of aluminum alloys' resistance to the unstable fracture was provided. Besides, the rupture mechanisms of high strength 7075 and 7050 aluminum alloys were investigated. The specimens were used as solution treated, quenched and aged condition. The elastic-plastic behavior of specimens was determined by carrying out tensile test on cylindrical specimens. The small sized specimen with 6.35 mm thickness and V-notched radius less than 60 µm was used for evaluation of damage properties, in accordance with ASTM B871-96 standard test method. All tear specimens were machined in L-T orientation. The mechanical tests were conducted at RT on an universal Instron machine under cross head speed of 0.1 mm/min. The results of mechanical tests made the evaluation of tear strength to 0.2 % tensile yield strength ratio, as a measure of notch toughness, available. The comparison of specimens' resistance to crack propagation and unstable fracture due to the presence of crack-like strain concentrator was provided using tear test data. The microstructure of specimens was studied under optical microscopy. The rupture micro-mechanisms were analyzed by examination of specimens fracture surfaces using SEM. The microstructure examination indicated almost equiaxed grains on the transverse directions and elongated grains on rolling direction. Moreover, intermetallic particles were evident at microstructure. Considering the SEM fractographs, it seems that the intermetallic particles act as void nucleation and damage initiation sites. However, the damage mechanism of tensile specimens and severely notched specimens, especially near the notched root differs due to stress and strain states.

Jan 1, 2006

By Lorna Ortiz-Soto

A series of titiania- and silica-supported Au, Pt and Pt-Au catalysts prepared through different synthetic routes have been investigated in terms of their structural properties, adsorption of CO, and catalytic activity for the selective catalytic reduction of NO by propylene and the oxidation of and CO. Catalysts prepared by incipient wetness impregnation from individual Pt and Au precursors, exhibited characteristics very similar to those of monometallic Pt catalysts. This behavior is consistent with a model in which the two metals remain segregated due to their miscibility gap, and only Pt participates in the adsorption of CO and the reactions under consideration. In contrast, catalysts prepared from a Pt2Au4(C=CtBu)8 organo-bimetallic cluster precursor exhibited different behavior both in terms of CO adsorption and their catalytic activity for the three reactions examined. The combination of the kinetic, spectroscopic and structural characterization data suggests that in this case Pt and Au remain intimately mixed in the form of Pt-Au bimetallic particles, and that the presence of Au modifies the behavior of Pt.

Oct 1, 2003

By Kwang-Hyun Jeon

Recently, 3D printing technology in the manufacturing field is in the spotlight. In the construction industry, similar rapid prototyping technology that does not use conventional form can be applied to meet the demand on free formed structure that can provide aesthetic value and functionality. Conventional formwork can increase construction cost and period for various structure with complex shapes while it has numerous advantages such as high strength, convenience, accuracy and good quality of surface roughness. To meet the demand on free formed structure, automated freeform construction systems such as Contour Crafting and Concrete Printing have been developed with active collaboration between university and industry in USA and England. However, details on the system have not been fully released in public, so the possibility of its fusion and spin-off technology cannot be expected. In this paper, cost-effective solution for mechanical and control system for constructing a free curved structure without mold are described. As an appropriate material for the system, fiber reinforced mortar was selected by experiments on compressive strength, setting time and fluidity. After performing G-code simulation, transfer and extrusion experiments with the selected mortar mix were performed and the possibility of the development of automated freeform construction system was demonstrated. Based on this research results, it is required to keep the automated freeform construction system improve and extend it into the new application area in construction industry.

Aug 1, 2013

By Willie Manfrey, Richard Klimpel

This paper describes the effects of slurry viscosity on the selection-for-breakage and breakage distribution parameters in the wet grinding of cres. A series of experimental tests were run on laboratory scale ball mills. Slurry viscosities were modified by varying the solids/water ratio with and without the presence of selected chemicals. Very consistent and predictable correlations are shown to exist. The grinding parameters were calculated using a computerized back -calculation technique developed by Klimpel and Austin. Industrial scale circuit calculations and preliminary plant trial data suggest that considerable increases in throughput and/or fineness of grind can he achieved through the judicious use of chemical additives.

Jan 1, 1977

By Louis R. Bernier

Most systematic studies carried out on passive treatment systems incorporating the use of limestone drains, under aerobic or anaerobic conditions, essentially deal with the treatment of effluents from mines in the USA. A limestone drain typically comprises a trench filled with crushed limestone rocks surrounded by impervious materials. In the case of anoxic drains, the trench is generally isolated under a geomembrane liner covered with soil. Contaminated mine effluents flow by gravity towards these limestone drains where the passive treatment consists in bringing the carbonates into solution, thus increasing the pH and alkalinity. Factors to be considered in the design are: chemistry of the contaminated mining effluent ([metals, [Al], [sulfates], dissolved oxygen, acidity, pH), desired residence time, nature of the rock, grain size, density, void ratio and mass of the limestone rock used, alkalinity, life span and hydraulic behaviour of the drain. Certain secondary effects (saturation by sulfates, co-precipitation, adsorption) may either be beneficial (lowering the sulphate and metal load) or harmful (armoring the limestone rock and clogging of the drain). This paper gives a brief status report on the available knowledge on the use of limestone drains for passive treatment of mining effluents heavily loaded with metals. Examples given include the old Lorraine mine (Ni-Cu), Témiscamingue, where limestone and dolomite rock drains were installed in 1998 when a cover with capillary barrier effects was placed over the tailings site.

Nov 1, 2002

By Ruan Chi, Zhenyue Zhang, Zhengyan He

In order to understand what governs the leaching of exchangeable rare earth (RE) and impurities and enhance the RE leaching process, the effects of the concentration of ammonium sulfate, pH and leaching temperature on the migration of RE and aluminum (Al) during the leaching of weathered crust elution-deposited rare earth ore was studied. The elution curves for ammonium ion (NH4 +) were also studied to reduce the consumption of the leaching agent. It was found that a high concentration of leaching agent can enhance the leaching process of RE and Al, reduce the breakthrough volume of NH4 + and more rapidly obtain the equilibrium of NH4 +. However, excessive leaching agent can both increase the cost and the burden on the environment. There is almost no variation on the elution curves of RE and Al in the pH range of 4-8 and control of the pH of the leaching agent can be omitted. It is better for the leaching work to be done in summer since higher temperatures can enhance the RE leaching process and improve the use ratio of ammonium. Using 0.1 mol/L ammonium sulfate for leaching 250 g RE ore, 95.42% RE extraction can be obtained when the volume of leachate is 102.6 mL. At this moment, only 18.17% of NH4 + is used to exchange RE and 49.22% of NH4 + is left in the leachate that can be reused as leaching agent by replenishing ammonium sulfate. The results of our studies can provide theoretical guidance for high efficiency and low consumption exploitation of RE ores.

Jan 1, 2016

By G. Heinrich

Size by size recoveries and pentlandite liberation data from image analysis were used to evaluate plant tests of pentlandite flotation and pentlandite/pyrrhotite middlings flotation from pyrrhotite in a circuit treating low grade magnetic intermediates at the Strathcona Mill. Raising the pH with lime gave improved selectivity for liberated pentlandite but there were major losses of middlings unless the circuit was pulled hard indicating the need for finer regrinding. However, size by size recoveries at the normal regrind showed that, while the pentlandite recovery improved in the finer ranges, the pyrrhotite recovery also increased leading to little selectivity in any size range. A much finer regrind gave greatly improved selectivity in all size classes suggesting that 'surface polishing' as well as liberation effects were being seen. Using liberation data from image analysis of the products, surface polishing accounted for over 99 % of the improvement in selectivity. Unreasonable recoveries of more highly liberated particles were observed for liberation analysis by volume fraction but showed the expected trend in recovery when the analysis was based on surface liberation. The surface liberation data showed that the improved pentlandite recoveries after finer regrinding were to more than 90 % caused by improved liberation with the remainder contributed by surface polishing effects. The practical implications of this work are that i) the comparison of particle grades with product grades allows to estimate the effect of regrinding on co-flotation/entrainment, ii) surface liberation models should be used for evaluating recoverabilities by flotation and iii) regrind circuits may be set up to ensure that all particles go through the mill or that only the coarse fraction is reground depending on the surface scrubbing found to be required.

Jan 1, 1993

By P. Wanjara, M. Xiao, M. Jahazi, C. Poon

Using a robotic 4kW Nd:YAG-laser system, Inconel 718 (1 mm sheet) was welded with and without filler wire to investigate the effect of processing parameters, including power input and welding speed, on the weld geometry, microstructure and mechanical properties. By means of both nondestructive testing and microscopic examination, the weld quality was studied to determine the nature of the welding defects (porosity, cracking and bead shape) over the processing range of 3-3.5 kW for the power input and 4.5-6 m-min-1 for the welding speed. Application of the design of experiment methodology permitted the examination of the relationship between the process parameters and mechanical properties, from which the optimized laser welding conditions could be determined for joining Inconel 718. In particular, the research results indicate that Nd:YAG-laser welding technology can achieve defects free, mechanically sound welds with narrow fusion and heat effected zones.

Jan 1, 2006

By Marcel Laflamme

Underground mine workers are continuously exposed to many sources of noise and vibration in carrying out their tasks. Even though the vibration and sound level of some mining equipment is documented, it was found that this information is not readily available for many pieces of equipment and that it is not considered when choosing equipment or planning tasks. As well, health problems related to vibration and noise are among the main causes of work-related compensations in mines. Considering those facts and although no Canadian regulations could force employers to limit the exposure of their workers to vibration, the Société de recherche et développement minier (SOREDEM) decided to address the problem by including vibration among their research priorities. In order to characterize noise and vibration sources of different mining equipment used for underground mining, the authors have performed a study in 8 different mines in Québec on 28 different mining equipments. The paper will present the procedure that was followed to select the list of equipment to be evaluated and the low cost acquisition system developed to perform multichannel time domain acquisition in harsh environments. It will also present the results obtained for the noise level produced by the equipment as well as for the hand-arm and whole-body vibration exposures.

Aug 1, 2013

"An atmospheric process for the synthesis of scorodite(DMSP®)has beendeveloped,in which ferrous ions were oxidized by oxygen gas in the presence of pentavalent arsenic ions. Under optimum conditions, the synthesized scorodite (FeAsO4?2H2O) was well crystallizedand the crystals were faceted; the particle sizes were as large as 15 to 20 µm. In thisstudy, iron (II) sulfate heptahydrate (FeSO4·7H2O), arsenic (V) acid (60mass%H3AsO4) solution, and distilled water were used to prepare the original experimental solution (700 ml), in which the contents of Fe(II) and As(V) were 55.9 g/L and 50.0 g/L, respectively. The effects of various synthesis conditions, such as the type of oxidizing gas (oxygen or air), gas injectionrate, temperature, and the initial pH of the solution, on the size and shape of the scorodite particles wereinvestigated. From the experimental results, the changes in the shape of the scorodite particles wereclarified for each synthesis condition.INTRODUCTIONDOWA has developed a processfor synthesizing well-crystallized scorodite (FeAsO4•2H2O). Theprocess is named andtrademarked as DMSP® (Fujita et al., 2008; Fujita et al., 2008; Fujita et al., 2009; Fujita et al., 2009; Fujita et al., 2009, Kubo et al., 2010). In this process, oxygen gas is injectedinto a sulfuric acid solution containing large amountsof As(V) and Fe(II). Facetedscorodite crystals as large as 15–20 µm weregeneratedthrough the pre-formation of a gel-like precursor. However, it is known that the synthesized scorodite particles become smaller and more aggregatedwhen the synthesis conditionsdeviate from the optimumconditions.In this study, the effects of various synthesis conditions, such as the type of oxidizing gas (oxygen or air), gas flowrate, temperature, and initial pH of the solution, on the size and shape of the scorodite particles were investigated. The experimental resultsclarified the changes in the shape of the scorodite particles for each synthesis condition."

Jan 1, 2016

By W. Qin

The nucleation of d hydride in Zircaloy-4 has been studied using electron backscatter diffraction. Hydrides prefer to nucleate at intergranular rather than intragranular sites. (0001) a -Zr//(111) d -ZrHx is the most common crystallographic relationship. The hydride platelets are generally interlinked each other and form a chain-like configuration. Based on thermodynamic model, the formation mechanisms of the hydrides at different sites and the interlinked structure were analyzed. We found that the misorientation of two adjacent grains has a crucial effect on hydride nucleation sites, and the tensile stress near the tips of hydride platelets is a key factor affecting the appearance of interlinked structure.

Aug 1, 2010

By C. Hu

A MOS capacitor hydrogen sensor array is reported for hydrogen gas distribution mapping. Si(100) was used as substrate for film deposition. After silicon oxide growing on the silicon surface with dry thermal oxidation, palladium film was sputtered on silicon oxide as hydrogen-sensitive gate material in MOS structure. The 3x3 sensor array was patterned on silicon substrate and packaged in one chip. Sensors' response was test with impedance analyzer. The sensors in array were calibrated in the hydrogen concentration range from 10ppm to 10000ppm. The 2D hydrogen concentration distribution was obtained with the calibrated sensor array.

Jan 1, 2005

"The Kidd Creek concentrator is situated adjacent to Highway 101, twenty-four kilometres east of the center of the city of Timmins, Ontario. Sulphide ore, received by train from the minesite twenty-nine kilometres away, is processed at a rate of twelve thousand metric tonnes per day. Saleable concentrates of copper, zinc, lead and tin are produced.The concentrator contains secondary crushing, grinding, flotation, gravity separation and concentrate handling facilities. The total concentrator manpower complement is one hundred and sixty-four which includes supervision and operating personnel. Twenty-one shift personnel are required to operate the processes involved and they occupy fifteen different operating positions in addition to that of the supervisor. These positions include:1 Central Control Operatorl Metallurgical Leader1 Dryer Control Operatorl Crusher Leader3 Copper-Lead-Zinc Flotation Circuit Operators1 Pyrite Flotation Circuit Operator1 Tin Plant Operator2 Grinding Operators1 Concentrate Operator2 Crusher Operators1 Spare Operator1 Tailings Area Operator1 Automatic Sample System Operator1 Dryer Area Helper1 Crusher Helper1 Tin Plant Helper"

Jan 1, 1981