Search Documents

By R. M. Lauer

OVER THE YEARS concentration of the Sullivan ore has become progressively more difficult as the ore has become increasingly refractory. The introduction of new reagents and changes in the flow of the concentrator have been and continue to be necessary in order to maintain and improve the efficiency of metal extraction. Prior to the completion of the pilot mill in 1957 ail new ideas were developed in laboratory equipment. If these were found to be promising, there was no alternative but to introduce them directly to the main mill flow in one step. When a major change was involved there was always the possibility of serious losses while the mill was being adjusted to the changed conditions. It proved difficult to determine whether these losses were the result of the changed procedure or of failure to adjust the flow to a change in the condition of the ore during the test. The pilot mill has provided a valuable intermediate step between the laboratory and the mill. It avoids the losses which occurred when unsuccessful full-scale tests were attempted, and conversely it provides assurance that full-scale flow changes can be made without serious hazard.

Jan 1, 1960

By J. D. Clucas, N. Verbaan, T. Grammatikopoulos, D. B. Dreisinger, C. Forstner, M. Aghamirian

"Search Minerals is currently exploring the Port Hope Simpson (PHS) Rare Earth Element District in southeastern Labrador, Canada. The Foxtrot Rare Earth Element (REE) Project in the PHS District has a 43-101 resource estimate consisting of 3,410,000 tonnes of Indicated Mineral Resources and 5,850,000 tonnes of Inferred Mineral Resources. The indicated and inferred resources contain 1.07% and 0.98% total rare earth element oxide (including yttrium), respectively. The dysprosium and neodymium grades are particularly attractive at 218 ppm Dy2O3 and 1687 ppm Nd2O3 for the indicated resources and 208 ppm Dy2O3 and 1494 ppm Nd2O3 for the inferred resources. The mineralization remains open along strike and at depth and is only one of a number of attractive exploration targets in the Port Hope Simpson area. The REE minerals fergusonite and allanite are present. The ore can be beneficiated by gravity, magnetic separation and flotation to a recovery of +80% for the individual REE. Acid bake and water leaching may be used to extract REE into solution for subsequent purification and recovery. The extraction range for single stage leach tests were 91-96% for Nd, 84-87% for Tm and 92-94 % for Dy with modest acid consumptions. INTRODUCTIONSearch Minerals Inc. (Search) is exploring the 100% owned Port Hope - Simpson District in Labrador, Canada for rare earth elements (REE). This District is approximately 135 km by 12 km in size, and is highly prospective for heavy and light rare earth elements. A total of 11 REE prospects have been discovered in the District to date, including the Foxtrot. In addition, Search is exploring in the 100% owned Henley Harbour region and has joint ventures with Quest Rare Minerals in the Strange Lake region, and with Great Western Minerals Group in the Red Wine complex, all in Labrador. These exploration locations are illustrated in the Figure 1. The focus of this paper is the investigation of the mineralogy and processing of Foxtrot REE materials. The Foxtrot resource falls within the claims held by Search in the Port Hope Simpson REE District. The infrastructure available at Foxtrot is excellent with a deep water port, air strip and road and power infrastructure at Port Hope Simpson. Over $7 Million has been spent to date on exploration and development of the District. The Foxtrot has been explored using prospecting geochemical methods, geophysics (airborne and ground), channel sampling of surface outcrops, mapping and three phases of drilling (18,934 m total)."

Jan 1, 2012

"The pressure leaching of alkali-pretreated limonitic laterite ore in nitric acid was studied. The optimal leaching conditions are as follows: leaching temperature of 458 K, initial nitric acid of 2.44 mol/L, leaching time of 60 min, liquid to solid ratio of 2:1 mL/g, agitation speed of 500 RPM. Under the above conditions, the extraction of nickel and cobalt can be achieved as approximate 95% and 80% respectively while that of iron is as lower as 1%. The leaching residue containing 70% of iron in the form of hematite and trace amount of chromium is suitable as the raw material for iron-making. The nitric acid in the leaching solution can be regenerated and further recycled to leach. INTRODUCTIONIt has been estimated that 60%-70% of the world land-based nickel resources presented in nickel laterites containing 130 million tons of nickel although these only accounted for about 42% of the world nickel production (Sudol, 2005; Luo et al., 2010). The nickel resource of laterite has not yet been fully utilized. Due to the increasing global demand of nickel and the declining global reserves of nickel sulphides, there is an increasing focus on the processing of the huge reserves of laterite ores today. Nickel laterite ores can be simply divided into two types, namely, silicate-rich and limonite. The former can be treated effectively by pyrometallurgical process in which the ferronickel product or nickel/iron sulphide matte is produced (Monhemius, 1987). The limonitic laterite is rich in iron in the form of goethite which is the main nickel-bearing mineral and usually contains cobalt associated with a manganese phase (Chang et al., 2010; Georgiou and Papangelakis, 2004). The limonitic laterite is usually processed by hydrometallurgical methods, such as atmosphere acid leaching (AL) (Xu et al., 2005; McDonald and Whittington, 2008), high pressure acid leaching (HPAL) (Chou et al., 1977; Georgiou and Papangelakis, 1998; Rubisov et al., 2000; Whittington and Muir, 2000) and reductive roasting-ammonia leaching (Caron Process) (Whittington and Muir, 2000; Valix and Cheung, 2002). The AL process can proceed at lower temperature, thus the operation costs may be very low. But two biggest problems associate with the AL process, namely, the slow rates of nickel extraction and potentially the significant amount of impurities such as iron and aluminum in the leaching solutions, which hampers the wide application of the AL process. The Caron Process uses the pyrometallurgical and hydrometallurgical methods together to obtain the metallic values, but the overall metal recovery is relatively low, especially for cobalt. In recent years, the environment-friendly process of HPAL has become increasingly important because it is most suitable for low-grade ores and leads to high extraction of the valuables. However, the HPAL process needs a much higher temperature and pressure (503-533 K, 4-5 MPa) to maintain a relatively fast leaching rates, which results in higher operation costs. Moreover, another serious problem of scale formation in autoclaves occurs in the HPAL process, for example, in Moa Bay, up to 20 cm scale may build up resulting in 5 days descale downtime per month. In addition, the iron residues cannot be utilized for ironmaking due to the presence of high content chromium (Ema and Harada, 1987; Owada and Harada, 1987; Takagi and Furui, 1987)."

Jan 1, 2012

By D. Milne, P. Germain, G. Sauriol

"The practical determination of optimum stope geometry has, until recently, been an art relying primarily on experience at a given operation. Due to the complex and variable nature of rock masses in situ, stopes are often designed either very conservatively, resulting in excess development, or non-conservative resulting in excessive dilution and, in some cases, in loss of ore reserves.The Geomechanics group of the Mining Technology Division, Centre de Recherche Noranda, uses a combination numerical modelling and empirical design techniques to optimize allowable stope geometries. The above methodology allows the optim ization of stope geometry for varying rockmass classifications within an operation or between different operations. Such techniques require the development of a thorough geotechnical database at each operation and are best used when calibrated to the specific operation through back analysis.This paper discusses the above optimization techniques in light of specific examples from the Noranda Group. The design methods, limitations and results are discussed.INTRODUCTIONMine design has traditionally referred to production planning, general facility layout, (i.e. ore passes, crusher stations, main haulage drifts, etc.) and ventilation design. The dimensioning and sequencing of the stopes and pillars, however, has been almost solely based on trial and error and precedent practice.More recently, numerical stress analysis has received much more attention as part of the design process. It is common now at many operations to look at the effect of proposed stope layouts and sequences on stress redistribution through the surrounding mine workings. Through calibration of actual stope and pillar behaviour in situ, one can then relate the model predictions to support requirements, safety problems, etc."

Jan 1, 1989

By R. H. Duthie

As at any other mine in Canada, grade control procedures are used at Steep Rock Iron Mines (1) in order to ensure that concentrator and pellet-plant operator s have a uniform feed so that they can manufacture a pellet to suit buyers' specifications and (2) to maximize ore recovery so that as little as possible finds its way to the waste dump or is downgraded by contamination. At Steep Rock, material grading 40% to 66 % Fe is considered ore. The ore may contain up to 10% sulphur. These ranges create six different stock pile types, with the possibility of more if large concentrations of arsenic are encountered. Although grading and mining techniques used to accomplish these ends are fairly standard, there is an appreciation and willingness by hourly and staff pit personnel to make grade control effective. This produces vertical and horizontal communication, which is necessary for success in this field. At Steep Rock, the waste-to-ore ratio is greater than at any other iron ore mine in Canada. Also, a high percentage of the ore mined is direct pellet feed. For these reasons, .grade control is very important.

Jan 1, 1977

By J. R. Gill

Introduction The property and plant of the Falconbridge Nickel Mines, Limited, is situated about 13 miles northeast from Sudbury, in Falconbridge township, near the eastern extremity of the southern Nickel Range. As early as 1899 or 1900 some work was clone on this property by the late Thos. A. Edison, when a shaft was sunk through 80 feet of overburden to within a few feet of the ore-body. At this point quicksand was encountered, which made it impossible to continue with the equipment at hand. As a result, the activities of the Edison party ceased in this section. There was no further progress until 1915 and 1916, when an extensive diamond-drilling campaign, carried out by the E. J. Longyear Company, located the ore-body that is now being worked. The property was acquired by the present operators in 1928, and in September of that year active mining development was commenced. Features Influencing Design Of Plant Early in 1929 plans were prepared for a smelter and the necessary crushing and sorting plant. In spite of the general trend towards the reverberatory furnace as a smelting unit, it was decided to erect a blast-furnace plant. The limited tonnage to be treated, of course, influenced this decision to a great extent. However, it was known that, with the proper procedure, extremely favourable results, both economic and metallurgical, could be obtained in blast furnace smelting. The possibility of very low slag losses, the simplicity of operation by the elimination of roasting plant, fuel plant, etc., the ability to handle coarse feed, and the lower initial cost, were considered factors in favour of the blast furnace. Notwithstanding the fact that we might be called on to treat a certain amount of concentrate, it appeared that the blast furnace was the proper unit for the contemplated operation.

Jan 1, 1932

By K. Ihara, T. Yamaguchi, K. Matsumoto

"Al-Fe alloy sheets having layers with different strain components were produced by unlubricated hot rolling and the recrystallization texture formation during annealing was investigated in each layer. In this study, the strain component introduced by rolling was quantitatively evaluated by measuring degree of bending of an aluminum pin embedded in the sheet. The textures before and after annealing were investigated by the SEM-EBSD technique. It was clarified that, in the middle layer, where comparatively small shear strain was introduced, ß-fiber subgrains and cube {001}<100> oriented subgrains were formed before annealing, and cube oriented recrystallized grains grew after annealing. On the other hand, in the surface layer, where large additional shear strain was introduced, shear texture components and cube oriented subgrains were formed before annealing, and shear texture was retained even after annealing, while cube oriented subgrains did not grow and were encroached. It was suggested that introduced strain components influenced the recrystallization texture formation by inducing different distribution of the subgrain size, stored strain energy and orientation relationship with surroundings before annealing.INTRODUCTION The microstructure developed during the hot-rolling process of aluminum and aluminum alloys affect the mechanical properties of the final product sheets. Especially, the crystallographic orientation in the final product sheets affects the r- value and ears during deep drawing (Humphreys & Hatherly, 2004), then the texture control in the hot-rolling process is important. When the friction between the rolling roll and rolled sheet in the hot-rolling is large, both the rolling texture and recrystallization texture tend to be heterogeneous in the thickness direction. It is known in many rolled aluminum alloy sheets that the texture in the surface layer was different from that in the middle layer because of additional shear strain. It was reported that in the vicinity of the surface layer, where large additional shear strain was introduced, the shear texture <1 1 1>//ND and < 1 1 0> // RD which contain components of {1 1 1} <1 1 0> and {0 0 1} <1 1 0> developed during rolling, and the shear texture developed even after recrystallization annealing (Sakai et al., 2002). Particularly, it is thought that the <1 1 1> // ND texture contributes to improve the r-value and press formability (Inoue & Takasugi, 2007). Therefore, asymmetrical rolling and high friction rolling have been applied to improve formability of aluminum alloys by adding shear strain in the rolled sheets as deep as possible (Kamijo et al., 1972; Inoue et al., 2005). However, few researches have been focused on the microstructures and texture before annealing and thus, the detailed mechanism is still unclear how the texture after annealing is affected by the texture before annealing. In this study, the Al-Fe alloy of commercially pure aluminum was chosen as the first material to be studied in order to clarify the fundamental process of the recrystallization texture formation. The main purpose of this study is to clarify the effect of additional shear strain on the rolling and recrystallization textures in the hot-rolled sheets by analyzing the transition of microstructure and orientation distribution through recrystallization annealing."

Jan 1, 2018

By Stéphane Robert

This document presents estimates of future "total cash cost per ounce" and "minesite cost per tonne" that are not recognized measures under United States generally accepted accounting principles ("US GAAP"). This data may not be comparable to data presented by other gold producers. These future estimates are based upon the total cash costs per ounce and minesite costs per tonne that the Company expects to incur to mine gold at the applicable projects and do not include production costs attributable to accretion expense and other asset retirement costs, which will vary over time as each project is developed and mined. It is therefore not practicable to reconcile these forward-looking non-GAAP financial measures to the most comparable GAAP measure. A reconciliation of the Company&apos;s total cash cost per ounce and minesite cost per tonne to the most comparable financial measures calculated and presented in accordance with US GAAP for the Company&apos;s historical results of operations is set forth in the notes to the financial statements included in the Company&apos;s Annual Information Form and Annual Report on Form 20-F, for the year ended December 31, 2009, as well as the Company&apos;s other filings with the Canadian Securities Administrators and the SEC.

May 1, 2011

By Veerendra Singh, Y. Rama Murthy, Sunil Kumar Tripathy, Nikkam Suresh

"High intensity dry magnetic separation is commonly employed to separate different para-magnetic minerals including mineral sand. Separation in these separators is majorly influenced by the combined effect of gravity, centrifugal and magnetic forces on a particle. These separators are included in the process flow-sheets either for pre-concentration purposes or for the beneficiation of paramagnetic minerals. Separation in these separators is majorly influenced by the difference in the magnetic susceptibility of the associated minerals, particle size and shape along with the process variables of the machine. Particle size is one of the major parameter that plays an important role and decides its probability of selectivity under the magnetic field. However, effect of particle size on the performance of these separators are not well understood which is evident from the literature.In the present investigation, an effort is made to bring out the effect of particle size on particle separation in an induced roll magnetic separator while treating ilmenite fines. Effects of operating parameters, such as; magnetic field intensity, roll speed, feed rate and splitter position have been studied and their influence on particle size has been analysed in terms of yield (wt.%) to magnetic product, particle size distribution characteristics in terms of D50 and D80 size, skewness, kurtosis. Also, the particle size distribution of each test was fitted in Rosin-Rammler equation. The test results were analysed statistically to understand and quantify the influence of each variable on particle separation. It is found that, rotor speed of the separator had maximum influence on yield to the magnetic product whereas splitter position had major influence on D50 and D80 (µm) size of the product."

Jan 1, 2016

By J. B. Mitchell

Using digital image correlation the evolution of strain and strain at the onset of localisation resulting in a hot tear has been determined for alloys AA6111 and Al¬0.5wt% Cu during solidification. High resolution images of hot tear formation and growth were captured during a constrained bar test that incorporated a glass window above a central hot spot region. The images were analysed using digital image correlation software to measure the evolution of displacement and strain based on tracking the motion of discrete features on the as-cast surface of the sample. Temperature data was also acquired with a thermocouple cast into the sample in close proximity to the hot tear. The interval starting from the point immediately after solidification shrinkage ends (the metal pulls away from the glass) and finishing when the first sign of a crack or hot tear is visible to the eye was used to determine strain data. The minimum strain at which strain localisation occurs was found to be 0.0069 in AA6111 and 0.0021 for A1-0.5%Cu.

Jan 1, 2007

By Fridrik J. Kristjansson, Stephen R. Hicock

"Three varieties of till are recognized in the Beardmore-Geraldton area: local lodgement till, nonlocal carbonate till, and local supraglacial till. The local lodgement till unit is examined in detail for the first time in this paper. It is the best potential overburden exploration medium for gold and other metals because its particles were locally-derived and deposited subglacially, probably within a few kilometres downglacier (southwestward) from their sources, and have not been diluted by distantly-derived glacialdebris. Both local tills are richer in gold and other metals, relative to nonlocal carbonate till. Local lodgement till rests on bedrock and was encountered frequently at or near the surface in thin drift/bedrock terrain (a widespread terrain type within the west half of the study area), and commonly at the base of boreholes in thick till terrain.INTRODUCTIONDrift prospecting in areas of glaciated terrain has been well documented (in a variety of journal publications and symposium volumes; e.g . Strobel and Faure 1987; MacDonald and Mills 1988) and has proven valuable especially where overburden thicknesses hinder traditional exploration techniques. Drift prospecting techniques may well prove valuable in the Beardmore Geraldton area. This applies especially to the Wildgoose Lake Turkey Lake area where a thick and laterally extensive sheet of nonlocal carbonate till has impeded conventional mineral exploration programs (Fig. I; note the lack of gold occurrences around Wildgoose Lake).Till in .particular has been cited as the best prospecting medium among the various types of glacial sediment (e.g. Shilts 1984). Three end member till varieties are recognized in the study area: (I) local lodgement till which rests directly on bedrock; (2) non local carbonate till; and (3) local supraglacial till which occurs predominatly within, or just downglacier of, upland areas where it commonly mantles the other till varieties. Previous authors have documented how the non local carbonate till hinders gold exploration (Geddes and Kristjansson 1986; Karrow and Geddes 1987; Kristjansson 1986; Hicock 1986, 1987a, b, 1988; Kristjansson and Thorieifson 1987; Thorleifson and Kristjansson 1987, 1988a, b) and why the local supraglacial till may be a good unit for prospecting (Hicock 1986). One detailed surficial geology map sheet of the area has been published (Kristjansson et al., 1988) and others are in preparation. Closs and Sado (1981) reported on the geochemistry of soils and glacial sediments in the west half of the study area. This paper documents the local lodgement till unit and demonstrates why it is the best overburden unit to use for drift prospecting."

Jan 1, 1989

"These guidelines, implemented in 2003, were recommended by the Diamond Exploration Best Practices Committee established by the Canadian Institute of Mining, Metallurgy and Petroleum. The guidelines are applicable to public companies and their consultants reporting diamond exploration results.“The guidelines are referenced in the Companion Policy of NI 43-101 with a statement that disclosure regarding the reporting of diamond exploration sampling results should conform to them.”Reporting GuidelinesThe following guidelines have been recommended by the Diamond Exploration Best Practices Committee established by the Canadian Institute of Mining, Metallurgy and Petroleum. These guidelines are applicable to public companies and their consultants reporting diamond exploration results.In respect of these guidelines, Diamond Exploration Results are results derived from the initial activities undertaken to investigate a diamond bearing prospect or deposit, to generate tonnage, grade and value estimates that cannot be classified as a Mineral Resource or Mineral Reserve. They do not address the earlier stage reporting of geophysical, geochemical or kimberlite indicator mineral results.Public reports of Diamond Exploration Results relating to mineralization not classified as Mineral Resource or Mineral Reserve must address the confidence limits of the result and contain sufficient information to allow a considered and balanced judgement of the significance of the results.The objective of these guidelines is to assist public companies and consultants in making appropriate disclosure of diamond exploration results by reporting in a manner which is:Uniform within the diamond exploration industry; Consistent with reporting from other industry sectors .Comprehensive .Unambiguous .The guidelines are not prescriptive. Materiality is the overriding principle that determines the information that should be disclosed. However, where a company or consultant deviates from the guidelines, the disclosure or technical report should state the extent to which the guidelines have not been followed, and the reasons for the deviation.The guidelines do not in any way replace jurisdictional reporting requirements (For example, the requirement for Canadian reporting issuers to comply with Canadian Securities Administrators National Instrument 43-101 by having technical disclosure endorsed by a Qualified Person as defined in that legislation)."

Jan 1, 2003

By Adrianus (Adrian) Halim, Tomas Bolsöy, Stina Klemo

"This paper describes the ventilation system used in underground hard rock mines in Sweden and Finland, which is very different than the system used in other major mining countries such as Australia, Canada, South Africa, and USA. The system utilizes auxiliary fans with Variable Speed Drive to distribute primary airflow to working levels instead of regulators that are commonly used in other countries. Descriptions about Ventilation on Demand in this system and ventilation regulations in Sweden and Finland are presented in this paper. This paper also quantifies a comparison between the Nordic and the system used in other countries. KEYWORDS Auxiliary fan, Regulation, Ventilation on demand (VOD), Variable speed drive (VSD) INTRODUCTION The primary objective of an underground mine ventilation system is to provide sufficient airflow to dilute atmospheric contaminants that are produced by mining activities. Typically, a mine ventilation system consists of one to four primary fans, regulators to control primary airflow distribution to levels or panels, and auxiliary fans that distribute airflow to dead-end workings via ducts. Depending on circuit geometry, underground booster fans are sometimes used. This system is widely employed in many countries such as Australia, Canada, USA, United Kingdom, and South Africa. However, mines in Nordic countries such as in Sweden and Finland employ a different system, in which auxiliary fans instead of regulators are used to control primary airflow distribution, as well as distributing airflow to dead-end workings. This paper describes the general layout of Nordic ventilation system, its VOD and heating system, its comparison with the system that is widely used in other countries which is referred as “Non-Nordic ventilation system” in this paper, and the current ventilation regulations in Sweden and Finland. The comparison was quantified by doing simulations using Ventsim Design 5 software. DESCRIPTION OF NORDIC VENTILATION SYSTEM General System Layout Figure 1 shows a schematic of typical ventilation system used in Swedish and Finnish mines. The schematic was drawn by Franzen, Myran, Larsson, and Rustan from Stiftelsen bergteknik forskning (Swedish Rock Engineering Research Foundation) and the English translation is written next to the Swedish terminologies. The system is generally a push-pull system. None of Swedish and Finnish mines use exhaust system. As shown in Figure 1, the primary airflow is distributed to levels by auxiliary fans that are bolted to a bulkhead located in the access to intake raise/shaft. These intake fans are attached to ventilation ducts that distribute airflow to all working faces. The exhaust auxiliary fans, which are not attached to any ducts and also are bolted to a bulkhead located in the access to exhaust raise/shaft, then flow the exhaust airflow into the exhaust shaft. A small quantity of this exhaust air is directed into the ramp, which acts as another main exhaust airway. The deepest level is also equipped with booster fan(s) that draw air from the intake shaft/raise and direct it into the ramp to provide fresh air in the ramp. There is no free split in this system. Figure 2 shows a schematic of a level ventilation layout in the Nordic system. Figure 3 shows a photo of these auxiliary fans."

Jan 1, 2019

By Ian S. Leslie

Seismic monitoring systems for mining operations are being utilized more than ever before in the characterization of rock mass response to underground and open pit mining. This paper provides a review of the use of microseismic monitoring for rock mechanics applications at mines throughout the world. Some practical considerations for the installation of these systems are presented along with techniques for optimizing seismic array coverage. Case studies and installation examples are also provided. Recent applications of advanced seismic analysis techniques are discussed including the determination of event mechanisms, mapping of maximum peak particle velocity (PPV) and seismic hazard fields, and the use of source parameter data for large event re-entry protocol.

Jun 1, 2012

By R. Le

"The principles of noise control aredescribed with particular emphasis on personalactive units as opposed to passive ear muffspresently in general use. A discussion followsfor their potential use in a mining environment.RÉSUMÉNous décrivons brièvement quelquesprincipes de contrôle de bruit à l’usage person-nel, puis nous passons en revue quelquescasques commerciaux dotés de ces circuits àprincipe actif. Enfn nous discutons de leurusage potentiel dans le contexte minier.IntroductionLe casque à principe actif est un produitqui existe commercialement, mais encore peurépandu en usage, sûrement à cause du prix,mais aussi de sa méconnaissance par le grand public. Il arrive parfois qu’un journaliste trouvele produit fantastique et le médiatise commeune réalisation de son pays (ou de sa province),mais peu savent qu’il s’agit là d’un principe quia commencé dans les années 30. Par delà lesensationnel, il reste que si l’on veut mettre lamain sur un de ces casques pour l’essayer, on nesait où l’obtenir. De plus, les casques n’utilisentpas tous le même principe actif. C’est la raisonpour laquelle nous faisons cette brève compara-ison. Nous le faisons en mettant l’accent pourune possible utilisation dans le domaine minier,car c’est dans ce milieu que les usagers sontconfrontés aux bruits les plus intenses qui peu-vent endommager leur système auditif, ce quin’exclut pas les autres situations (travaux publics, foresterie, écoute hi-f, etc.)."

Jan 1, 1997

By W. M. Williams

"Although manganese is a metal virtually unknown to the layman, it is hardly necessary to point out to the engineer the importance of manganese in modern metallurgy, an importance intimately linked with iron (and steel), the basic materials of engineering construction for hundreds of years and certain to remain so for long into the future. World steel production will approach and perhaps reach 1 billion tons/year in the 1980s; with a manganese content between 0.5% and 1 % in ordinary steels, and more in specialty steels, manganese use worldwide will soon approach 15 million tons annually. Manganese was discovered and isolated in Sweden in 1774 by Karl Wilhelm Scheele (who also discovered molybdenum), but the element was only of scientific interest for several decades. By the early part of the nineteenth century, however, manganese oxide had become commercially available and was in use for colouring glass and for the production of chlorine. Commercial application in metallurgy appears to have been limited to the manufacture of crucible (or ""cast"") steel, a highquality product made by carburizing wrought iron, and melting it in small batches to make ingots which could be rolled and used for special applications, e.g. for the manufacture of fine tools or for ""steeling"" the cutting edges of implements such as wrought iron axes and chisels.* However, it was not until Bessemer&apos;s epoch-making invention of cheap steel in 1856, and the dramatic expansion of the steel industry thereafter, that manganese assumed the importance that it holds in modern steelmaking."

Jan 1, 1999

By O. Neves, C. G. González Beca, M. C. Sol Pereira, H. Sousa Vale, R. A. Guedes de Carvalho, M. N. Sampaio

"As sulphide ores are usually concentrated by flotation , the material is very finely ground <37um), wet and impregnated with the chemicals used in flotation. These conditions are favourable to the development ofchemical reactions which are largely influenced by atmospheric conditions (temperature, humidity, wind, etc.) as well as by the geometry of the piles.Physical and chemical properties of a chalcopyrite concentrate were determined by laboratory tests. The knowledge of these properties was considered necessary in order to establish a correct design of the storage and handling operations of the sulphide ore concentrates obtained by flotation.The properties studied in this work were: transportable moisture limit, flowability, effects of vibration, hygroscopicity, ""caking"", chemical alterations by humidity, oxidation and self-heating (auto-ignition, dry and wet oxidation, self-heating by humidification and its prevention).INTRODUCTIONIn order that the handling and the transport of a powdered material may be carried out correctly, it is necessary to know certain physico-chemical characteristics. Transportable moisture limit (TML), apparent density (both aerated and compacted), compressibility, angle of repose, angle of spatula, cohesion and angle of slide(l-4) are characteristics (among the flowability parameters) worth knowing.Moisture content of the powdered material is fundamental, because if this is too low heavy losses will occur when the product&apos;s particle size is very small, if it is too high, separations between solid and liquid phases may occur. In the latter case, the centre of gravity of the system may change suddenly and cause accidents, mainly if transport is by sea or by river."

Jan 1, 1989

By G. A. Witwicki

"The Thyssen Mining Group of Companies has successfully applied ground freezing technology to numerous projects throughout Europe and North America for over 100 years. Recently, the aspect of data acquisition and data verification has received greater focus.Thyssen Mining has been engaged in several relatively deep shaft sinking projects over the past five (5) years, all of which have required ground freezing to successfully sink through water bearing rock. To safely and economically sink through a quantity of water similar to Saskatchewan’s Potash Mines, it is imperative to understand freeze wall thickness and growth rate.Critical to understanding freeze wall thickness and growth rate, is the collection of accurate data as well as the interpretation of those data. The data can then be utilized to gain a better understanding of the freeze wall growth rate in active projects as well as to provide data to be utilized in modeling for future projects.This paper elaborates on the installation and operation of the data acquisition system utilized at the Newmont Leeville project, Nevada’s first frozen shaft project. In addition, this paper elaborates on the methodology developed by Thyssen Mining to manipulate the freeze wall data derived through the data acquisition system.The successful incorporation of the new system of collection and analysis of freeze wall data for the Leeville Project has given Thyssen Mining a high degree of confidence in the understanding, as well as prediction, of the ground conditions during shaft sinking.This paper will include:•,A brief description of ground freezing and its objective;•,An overview of previous data acquisition methods employed;•,Current data acquisition methods;•,Installation requirements; and,•,Data manipulation and presentation methods."

Jan 1, 2015

By Robert Dickson

Princess colliery is operated by Old Sydney Collieries, Limited, a direct descendant of the General Mining Association of London, England, which, in the first quarter of the nineteenth century, pioneered in coal mining in Nova Scotia. The coal worked is a 5 ft. 6 in. seam known generally through the Sydney coalfield as the Harbour seam but referred to locally as the Sydney Main. Entry is made by shafts, 680 feet deep, sunk in 1871 on a headland forming the northern entrance to Sydney harbour. From them extend the main roadways of the colliery, a distance of 700 feet to the shore line and a further distance of 14,700 feet in submarine areas to a total length of 15,400 feet. It was the first colliery in Nova Scotia designed to work submarine areas. Lateral development extends across a frontage of 16,000 feet and the submarine area from which the coal has been extracted is slightly over 6 square miles. There yet remains sufficient territory ahead of the workings to assure a future life to this colliery estimated at over 80 years at the current rate of production. In this area the seam dips at 6 to 7 per cent and face workings have reached a depth of 1,690 feet below the sea level. Until 1923 extraction of the coal was by room-and-pillar, followed by the drawing of the pillars. At that date the superincumbent strata had reached a thickness of 1,400 feet, resulting in heavy weighting on the roof and severe side pressure on the coal ribs. In combination with a soft, heaving pavement this created a set of conditions involving great difficulties and expense in keeping open places driven in the solid sufficiently long to permit recovery of the coal in the pillars by methods and equipment then available. The operator was forced to resort to extraction by longwall as the only economical method of winning the coal.

Jan 1, 1948

By N. C. Karmakar, Y. V. Rao, M. Aruna

No one can properly work without sufficient light and this is especially so in mines where conditions are difficult. Artificial lighting is very important for the night shift to provide a safe and efficient working environment, which must be evenly illuminated with no obvious dark spaces and a minimum amount of glare. During an illumination survey of a large mechanized surface mine, it was found that the illumination level varied and was not uniform throughout the length of the road; it was high at one side of the road instead of at the centre. There were also different combinations of lamps, with angles of light arm varying from 35º to 70º. In this respect, an experimental study was carried out with a fabricated telescopic light pole to uncover the optimum design parameters of lighting installations. The analysis was done by plotting isolux contours for fixed installations and drawing graphs for various combinations of luminaries, reflectors, light arm angles, and height of lanterns by plotting the horizontal angle of the light arm along the abscissa, and the contour area along the ordinate. The study revealed that the design parameters of the lantern are mainly dependent on the type of luminaires. It was revealed that the pot reflector with a combination of tubular bulbs produces a wide distribution of light, and contributes towards a reduction of luminaries when installed in longer roads.

Jan 1, 2005