Search Documents

By Jr. Watts, B. K. Cantrell, K. L. Bickel, J. F. McDonald

"A field trial was conducted at an underground gold mine to evaluate diesel fuel derived from soybean oil (soy-methyl-esters or “biodiesel”) as an alternative to commercial, low-sulphur, number 2 diesel fuel (D2). A 2.7 m3, 18-ton load-haul-dump (LHD) unit, powered by a naturally aspirated, indirect injection (pre-chamber), 100 kW diesel engine was used as the test vehicle. The LHD was equipped with a diesel oxidation catalyst. The LHD operated satisfactorily on the biodiesel fuel. Operators observed a slight decrease in power and an absence of black smoke.Diesel particulate matter (DPM) concentrations were monitored for a six-week period while the LHD was operated with either the biodiesel fuel or the D2 fuel. DPM concentrations were measured in the mining section’s clean air intake, exhaust and on the LHD. Reduction in DPM emissions was determined from the measured difference in DPM concentrations between the clean air intake and the exhaust. The biodiesel fuel reduced energyspecific DPM emissions approximately 75%, from 3.6 ± 1.8 g/kW-hr to 0.86 ± 0.27 g/kWhr. Time-weighted average DPM exposure, measured near the LHD operator, was reduced from 0.67 ± 0.13 mg/sm3 to 0.28 ± 0.12 mg/sm3, or approximately 58%, when the biodiesel fuel was used. IntroductionDiesel exhaust consists of noxious gases and diesel particulate matter (DPM). Recent attention has focussed on the potential carcinogenicity of DPM and the potential health impact on miners. The National Institute for Occupational Safety and Health (NIOSH) recommended that whole diesel exhaust be regarded as a “potential occupational carcinogen”, and that reductions in workplace exposure would reduce cancer risks (NIOSH, 1988). The International Agency for Research on Cancer (IARC) declared that “diesel engine exhaust is probably carcinogenic to humans” (IARC, 1989)."

Jan 1, 1997

By Margaret Anne Stephenson

Today, in Australia, it is increasingly common to see agreements between Indigenous peoples and resource companies being achieved generally as Indigenous Land Use Agreements or agreements pursuant to the ?right to negotiation? process under the Native Title Act 1993 (Cth). Despite progress in this area, resource development on Indigenous lands is not without its challenges for both the resource proponents and the Indigenous parties. History demonstrates that resource development on Indigenous lands has produced struggles between the traditional owners of the land and the resource proponents. In Australia their relationship is generally defined by issues of access to land and assuring continued access to the land for the life of the project. In this context, divisions in Indigenous communities often emerge. The proposed resource project can have the effect of polarising members of an Indigenous community. It may be regarded by some traditional land owners as an advantageous opportunity for the community and by others as a hazard to country and culture. The process of agreement making has proved not only a test for the Indigenous community but also for the resource proponent. In this paper we undertake a contemporary case study of a proposed Australian resource related-development project on Indigenous lands. This project involved a multi-billion gas hub precinct proposed at James Price Point in the Kimberley region in Western Australia. The James Price Point proposal produced a litany of challenges for all parties. The traditional owners faced fundamental social and human rights issues, including a minority opposition to the project, the project's potential cultural heritage impact, the threat of compulsory acquisition of their native title interest by a State government due to an initial failure to settle an agreement, a fracture of their unsettled land claim and a minority rejection of the agreement ultimately reached. Additionally, the ?green? lobby also rejected the proposed gas hub on environmental grounds bringing the green lobby into direct conflict with both the traditional owners in favour of the project and the resource proponent. Ultimately, Woodside announced its decision not to proceed with the proposed gas precinct at James Price Point, in April 2013. In this paper we analyse the complexity of the James Price Point gas hub negotiations with the traditional owners which resulted in an Agreement that promised to deliver substantial benefits for the Indigenous communities. We question why such a favourable and beneficial agreement for the Indigenous community also produced the plethora of challenges and concerns and we consider how future negotiation processes could be better structured to avoid the difficulties that have confronted Indigenous land owners and resource proponents alike.

Aug 1, 2013

By Dan Alexander, Ivan Crnkovic, Sarah Schwarz

"Several plant studies have been conducted at the Zinifex Century Mine over the past 5 years. For each of the plant studies, surveys of the zinc primary circuit were conducted, characterisation measurements for each operating cell taken, and the floatability components of the ore mapped to develop a model of the circuit. The floatability components and machine parameters were then used to simulate changes in circuit configuration and operating conditions, enabling further potential improvements in circuit performance to be identified.This paper reviews the current flotation practice at the mine, as well as various circuit changes and developments implemented by site. The application of the methodology and the evolution of the standard procedure are also discussed.INTRODUCTIONBase metals were first discovered in the Lawn Hill region of Queensland’s North West in 1869 and the first mining lease in this area was pegged in 1887 over what is now known as the Silver King vein deposit. The area encompassing these veins, which includes the Century deposit, was proclaimed the Burketown Mining Field in 1899. Exploration titles were granted to CRA in 1987, precisely 100 years after the initial discovery at Silver King, hence the name ‘Century’.Century was commissioned by Pasminco in late 1999, with the mine becoming fully operational on 1 March 2000 and the official opening taking place in April. Pasminco had bought the Century and Dugald River deposits from CRA in 1997 for A$345 million, and invested some A$710 million in bringing Century into production. Today, Century is the world’s second-largest zinc mine in terms of its output, having reached full capacity in 2003.The Zinifex Century Limited (“ZCL”) lead-zinc-silver deposit is located approximately 250 kms north-north west of Mt Isa in north-western Queensland. The deposit is a large flat-lying ore body covering an area of some 1.2 by 1.4 km, the 45 m-thick stratabound sulphide orebody is hosted within an 850 m-thick sequence of Proterozoic siltstone, shales and sandstone, amenable to open-cut mining methods. The mine has ramped up to full production delivering five and a half million tonnes of ore per annum, yielding approximately 900,000 tonnes of zinc concentrate and 90,000 tonnes of lead concentrate. Mine life is expected to be about 8 years"

Jan 1, 2008

By S. Makni, S. Koppalkar, A. Bouajila

ABSTRACT This paper briefly reviews the gravity recovery between conventional and centrifugal gravity separators. The advantages of semicontinuous gravity separators will be discussed, as will techniques for upgrading the gravity concentrates. The research efforts in optimizing semicontinuous gravity separators will be recalled. An innovative gravity circuit for eliminating or minimizing the use of complex processing schemes will be reviewed. Ongoing gold gravity research has revealed that gold particle shape transformation is one of the main factors explaining the lower recoveries of the plant units. Efforts to devise possible remedies for improving plant gravity recovery will be discussed.

Jan 1, 2013

By H. E. Urtubia, C. W. Bailey

"BHP-Billiton’s Minera Escondida Limitada is one of the world’s largest copper producers. It treats a combined 88 million tons of copper ore per year through its two concentrators: Los Colorados and Laguna Seca. Over the past three years, metallurgical sampling has been performed at the Laguna Seca concentrator to calibrate both the JKSimMet and JKSimFloat grinding and flotation simulators. In the past, the calibrated simulators have been used to predict the effect of changes in operating conditions in the grinding and flotation circuits separately. To assist in the development of future processing options, predictions were required of the effect of changing grinding circuit conditions on flotation performance. This was achieved by using an integrated grinding and flotation simulation. The grinding circuit performance was predicted under different operating conditions (such as tonnage rate and product grind size) using JKSimMet, and these results were then used in JKSimFloat to predict the flotation performance for the new grinding circuit product. This combination of the simulators allows both the effects of residence time and grind size on flotation performance to be investigated.This paper presents the first combined grinding and simulation modelling and simulation case study using JKSimMet and JKSimFloat. The modelling and simulation methodologies for the grinding and flotation circuits are discussed along with the circuit simulations that were performed. The simulator predictions are presented in conjunction with independent laboratory results of the new operating conditions. The ability to predict flotation circuit performance based on changes in grinding circuit performance is also discussed. This methodology provides improved predictions of flotation circuit performance when grinding circuit changes (including grinding capacity increases) are made.INTRODUCTIONOver the past decade, the grinding and flotation research groups at the Julius Krutschnitt Minerals Research Centre - JKMRC (Brisbane, Australia), University of Cape Town (Cape Town, South Africa) and McGill University (Montreal, Canada) have been developing a methodology for optimising grinding and flotation plants using actual plant data together with semi-empirical sub-process models. The project is being conducted as part of the Australian Minerals Industry Research Association (AMIRA) P9 Project, titled “The Optimisation of Mineral Processes by Modelling and Simulation”. The project first commenced in 1962 and is currently in its “Nth” phase."

Jan 1, 2007

By B. Arlyuk

On the basis of research of relations among the market participants the analytical model has been created which connects the price of industrial good at stock exchange with volume of sales and the stock of the sellers and buyers, Also a model was developed for assessment of these parameters of the market status by the actually fixed stock exchange and general market indicators. The composition of these models made it possible to create reliable system of short-term price forecasting for commodities or base metals up to one quarter ahead. Imperfectability of creation a model for reliable price forecasting by purely statistic methods (by the "black box" principle) was shown. A model of price behavior qualitative forecasting till one quarter ahead has been developed, which determines the probability of reaching in future of the given level as well as of the price maximums and minimums, Optimal values of threshold probability were determined for forecasting the future price maximums and minimums securing the maximum profit from the forecasting system application for commercial activity. The developed system of forecasting was identified for primary aluminium at the period of 1990-2003. The system was tested daily during 20 months period for speculations on 3M primary aluminium forwards at London Metal Exchange with high commercial result.

Jan 1, 2004

By K. Szczesny

This paper considers the integration of uncertain real-time logistics data for reactive construction scheduling. In order to manage a construction project efficiently, an accurate schedule representing the current project progress is inevitable. The quality and up-to-dateness of such a schedule depends on the availability of real-time data. Typically, real-time logistics data contain information about the availability of material, equipment and personnel as well as delivery dates and site conditions. The accuracy and inherent uncertainty depends on the location where the real-time data was acquired. Currently, the integration of such data into a construction schedule is a very time-consuming, manual and, thus, errorprone process. Therefore, this paper proposes a methodology that enables an automatic integration of such uncertain data into construction schedules. By integrating uncertainties into the existing schedule their impacts on the construction work can be evaluated. For this, discrete event simulation is applied. In order to model uncertain input parameters for simulation models this methodology applies the fuzzy sets theory. In combination with alpha-cut sampling technique, discrete model input parameters are obtained. By applying reactive scheduling with several discrete event simulation experiments, the results can be used to modify construction schedules according to agreed timeframes and costs. In order to demonstrate and validate the presented approach an example is conducted.

Aug 1, 2013

By Patrick Moore

In 1971 the government of British Columbia issued a permit for the Island Copper Mine to commence disposal of 33,000 tons per day of mine tailings into Rupert Inlet, a marine fjord on the northwest coast of Vancouver Island. There was considerable controversy surrounding the development, public hearings were held, and as a requirement of the permit the company was obliged to carry out a comprehensive environmental monitoring program. The results of this program provide a thorough assessment of the environmental impact of submarine tailings disposal over the 24-year life of the mine. Following closure in December, 1995, the monitoring program continued for three years to determine the extent of marine ecosystem recovery and re-colonization. It is apparent from the findings of the monitoring program that the mine tailings were dispersed more widely than was originally predicted. It is also clear that widespread heavy metal contamination has not materialized. In retrospect it appears that submarine tailings disposal has resulted in far less severe environmental impacts than if the alternative of land disposal had been adopted. This review highlights significant aspects of public policy decision-making, design of environmental monitoring programs, and questions of interpretation of monitoring program data.

May 1, 2002

By B. Chareyre, H. Pourpak, L. Scholtès, E. Papachristos

"Numerical methods used to study hydraulic fracturing in low permeability rock masses need to take into account the interaction between the progressive failure mechanism of the intact rock matrix and the pre-existing natural fractures. A fully coupled hydro-mechanical 3D discrete elements model dealing with such interaction is presented here. The ultimate objective is to grasp the role of the rock-matrix failure on the propagation of the main fluid driven fracture under different stress fields and pre-existing fracture orientations. The proposed method provides the spatiotemporal distribution of the induced crack events which can be tracked during the simulations, making possible the identification of the local mechanisms leading to macro-failure in the rock matrix or reactivation of the discontinuity planes. Fluid flow inside a fracture, pressurized crack and hydro-fracking experimental tests were simulated as part of the validation process of the model and, are presented in this paper.INTRODUCTIONWith the expansion of shale gas and geothermal reservoirs exploitation, the technique of Hydraulic Fracturing (HF) has been widely used over the past years (McClure, 2012; Britt, 2012). Despite recent advances in micro-seismicity analysis or numerical modeling (Nagel et al., 2013), the way progressive failure of rocks affects the fluid flow depending on the in situ stress conditions or the rock heterogeneities is not fully controlled yet (Zoback, 2010).In this work we focused on setting up a three-dimensional discrete elements model to study fluid driven fractures propagation. The intact rock is modeled by a discrete element method (DEM) able to reproduce fracture initiation and propagation (Scholtès and Donzé, 2013, Garcia et al., 2013). The pre-existing fractures are explicitly modeled and can be individually defined or be part of a discrete fracture network (DFN) (Harthong et al., 2012). Their mechanical response is fully coupled with the fluid within a HM-DEM framework. The fluid flow and it’s interaction with the intact matrix and the pre-existing discontinuities is modeled through a Pore-scale Finite Volume (PFV) scheme specially enhanced for fractured rock modeling (Chareyre et al., 2012, Catalano et al., 2014) ."

Jan 1, 2015

By Matthew Violot

Introduction ?Located off highway 6, approximately 5 km, SW of Thompson, Manitoba ?Base metal mine: Nickel? Maximum Depth: 4100 ft ?Started Production in 1966 (INCO, 2006)?Halted in 1978?Re-opened in 1989 ?Two types of mining:?VBM (vertical block mining)?Cut and Fill 1.1 Problem ?Birchtree mine is experiencing failures and undesirable dilution in some of their stopes. ?Time can have a large effect on open stopestability. ?Birchtreeis interested in how time is affecting the stability of their stopes. ?The study focuses on the lower 84 complex, which extends from 2750 to 4100 foot level.

Nov 1, 2011

By S. S. Yuan, Q. Z. Zhu, J. F. Shao

"This paper aims at enriching a homogenization-based anisotropic damage model for hard rocks under complex loading. A new damage criterion is proposed to capture material strain softening. Within the framework of irreversible thermodynamics, we are particularly concerned with two strongly coupled dissipative mechanisms: frictional sliding and damage by microcracking, which usually take place at cracks within cohesive geomaterials under compression. Focusing on the representative elementary volume containing multiple crack families, the free enthalpy of the matrix-cracks system is obtained. Importantly, a back-stress term is involved in the local stress applied to microcracks. This back stress plays the hardening/softening role in the friction criterion which is formulated at local scale. Strain hardening owns to the accumulation of frictional shearing and dilatancy while strain softening is caused by crack growth. The multiscale damage model is used to simulate laboratory tests on the Westerly granite under true triaxial compressions. INTRODUCTIONWhen subjected to compressive loads, hard rocks present nonlinear mechanical behaviors and induced material anisotropies. In that process, two main dissipative mechanisms have been largely identified: damage by crack growth and frictional sliding along closed crack faces, which are usually strongly coupled to each other on crack scale. Theoretical investigations have shown that the damagefriction coupling analyses allow explaining a large number of experimental phenomena involved in brittle or quasi-brittle materials. Concerning constitutive modeling, the standard Eshelby’s solution-based homogenization procedure for heterogeneous materials was recently applied successfully to describing the mechanical and poromechanical behaviors of cracked frictional solids."

Jan 1, 2015

By M. Maldonado

This work details the application of a decentralized control strategy to a pilot flotation column working with a two-phase system (water-air). The process is represented by a multivariable system composed of three inputs and three outputs. The selected control variables are the froth depth, the air hold-up and the bias rate, whereas the corresponding manipulated variables are the set-points of the local flow controllers of tailings, air and wash water. All controlled variables are estimated using electrical conductivity based techniques. In particular, the results of a new method for estimating the bias rate, based on the measurement of the volumetric fraction of wash water under the interface, is presented. This method reduces the coupling problem associated to the bias estimation as a difference between feed and tailing water rates. Moreover, the nominal system transfer matrix can be represented by an upper triangular matrix, in such a way that the closed-loop system stability reduces to the stability of the independent control loops. The experimental results show that the closed-loop system performance, particularly that of the bias rate loop, is strongly dependent on the air flow rate, reaching in some cases the saturation point of the controller.

Jan 1, 2007

By W. S. Dyer

Considerable attention has been paid in recent years to the fire-clay and silica-sand deposits of the Mattagami and Missinaibi rivers and ? to the lignite occurring in them. The fireclay especially deserves this attention; it is of first-class quality; it appears to be widespread; it is the only fire-clay in central Canada, and part of it lies not more than 20 miles west of Coral rapids, to which point steel will be laid this coming spring by the Temiskaming and Northern Ontario railway. Undoubtedly, these clays will rapidly find a place in industry. The fire-clays and the better grades of silica-sand are Mesozoic in age and have been referred to the Lower Cretaceous or Upper Jurassic. Glacial clays and sands and Palaeozoic shales also occur in the same region, but are of little economic value, and will not be dealt with in this paper. Dr. Robert Bell was perhaps the first to discover the clays, since in the Report of Progress of the Geological Survey of Canada for 1877 and 1878 he reported beds of lignite on Coal brook, a tributary of the Missinaibi river, underlain by sticky clay and overlain by glacial drift. In 1880 E. B. Borron (1) discovered an extensive deposit of white sand and clay on the east bank of the Missinaibi river, five miles below Coal brook, and in 1890 (2) he examined the deposit found by Dr. Bell on Coal brook. He recognized that the underlying clays were quite distinct from the glacial clays of the region, and suggested that they might be used for fire-brick if metallurgical operations were undertaken in the region. Somewhat later, J. M: Bell described a deposit of fire-clay and silica-sand on the Wabiskagami river, another tributary of the Missinaibi.

Jan 1, 1928

By A. Moyano

The development of the traditional converting process performed in a PeirceSmith or Hoboken converter is limited by the investment magnitude associated to the fulfillment of the environmental regulations. Thus, the continuous converting process rather than a conceptual process alternative is becoming a necessity for a smelter facing limited converting capacity and/or lacking of fulfillment of the environmental regulation with its maximum converting capacity. The objective of this paper is to present the progress of the Codelco continuous converting process evaluated at pilot-scale level when converting solid mattes or white metal into blister copper. These tests allowed for gathering of relevant data to be considered for a new stage of evaluating the Codelco continuous converting at industrial-scale test. The pilot-scale tests were done in a Teniente Converter pilot scale unit at the Codelco Norte Smelter. The results of processing solid copper mattes (65-75% Cu) and producing low sulfur content blister copper with production of a constant S02 gas concentration, and the production of liquid slag with low copper solubility was achieved and is discussed in the present paper.

Jan 1, 2007

By Andre Panteleyev, Charels S. Ney, John M. Anderson

"Sam Goosly prospect, 22 miles southeast of Houston, B.C., was discovered in 1967 through geochemical reconnaissance. Soil sampling interpreted with respect to an east-to-west ice movement led to drilling targets.Mineralization is in a window of rocks thought to be Hazelton Group surrounded by Tertiary volcanic rocks and intruded by two stocks separated by about one mile. A westerly quartz monzonite stock is dated 61.1 m.y. and an easterly gabbro-monzonite complex is dated 52.5 m.y. The Tertiary volcanics are trachyandesites shown by the B.C. Department of Mines and Petroleum Resources to be in part extrusive equivalents of the gabbro, and they overlie Hazelton rocks uncomformably. Copper-molybdenum mineralization is sparsely developed in the westerly stock. Silver-copper mineralization forms an elongate west-dipping slab between the stocks in Hazelton rocks, which are continuously pyritized. The gabbro stock is not mineralized, but some dikes related to it are slightly so. Tertiary rocks are pyritized, but are not known to carry copper-silver mineralization. Hazelton rocks are divided into a lower conglomerate, an intermediate pyroclastic unit and an upper mainly sedimentary unit. They form a west-facing homocline. Coppersilver mineralization resides in the pyroclastic unit, mainly in a massive dust tuff through which are lenticular units of lapilli tuff. Well-mineralized rock is typically a breccia of light fragments in a dark chlorite-sulphide matrix. Sulphides are pyrite, chakopyrite and locally pyrrhotite, with very minor tetrahedrite, s phalerite and other sulphosalts. Rock alteration is predominantly a pervasive pyrite-sericite type, with widespread tourmaline, scorzalite, gypsum, ankerite and traces of fluorite. The most evident control of the copper-silver mineralization is the gross parallelism, over a strike length of 1.5 miles, to Hazelton strata, particularly a massive dust .tuff unit. In detail, mineralization crosscuts bedding and there is no appreciable banding within sulphides . A strictly syngenetic origin is untenable, but some initial concentration in a volcanogenic environment with subsequent modification by thermal processes seems likely."

Jan 1, 1972

An Atomic Force Microscope (AFM) was used to measure the surface forces between glass sphere and silica plate in CnTAC1 (n=12, 14, 16, 18) solutions. The results showed the presence of long-range attractive forces that can be fitted to single exponential functions. With a given surfactant, the attractive force increased with increasing concentration, and reached a maximum at the point of charge neutralization (p.c.n.). The decrease in the attractive force above the p.c.n. is probably due to the inverse orientation of the surfactant molecules. A plot of the log (p.c.n.) vs. the number of carbons in the hydrocarbon chains of the Cn TACI homologues showed a linear relationship with a slope of -0.37, indicating that the surfactant adsorption entails a decrease in free energy by -0.85 kT per mole of CH2 (or CH3) group. These results suggest that the adsorption of long-chain surfactants is controlled by hydrocarbon chain association during the process of forming surface hemi-micelles (or domains). Possible origins of the long-range attractions are discussed on the basis of the results presented in this communication.

Jan 1, 2006

Optimizing production scheduling in open pit mines is important for managing cash flows of mining operations. This paper describes a new, probabilistic, mixed integer programming (MIP) formulation which has been developed to minimize the risk of not achieving planned production targets, in terms of metal production and ore tonnage feed for the mill during production, while considering maximization of total discounted economic value. The new MIP model also recognizes that to minimize movement of excavators over long distances and accommodate equipment access, the blocks scheduled for mining within a period cannot be spread too widely. The model is applied to a laterite nickel-cobalt deposit, as an example of multi-element deposits that have complex ore quality constraints. The results show that the proposed model generates feasible schedules. When compared with traditional optimization techniques, the new model is superior in terms of minimizing the risk of not meeting production targets, especially at the early stages of production, and in terms of generating practical scheduling patterns.

Jan 1, 2006

By C. R. Edwards

"Equity Silver Mines Limited, Canada's largest silver mine, has designed, built and operated a leach plant to reduce the levels of antimony and arsenic in its silver-gold-copper flotation concentrate. The orebody contained deleterious antimony and arsenic minerals in such proportions that the economic long-term sales contracts necessary to obtain project financing could not be procured. Construction of the leach plant therefore allowed development of the mine to proceed. Although the plant took some time to reach design throughput and product specifications, due to the complex and unique nature of the operation, these goals were successfully met and surpassed. This paper describes the physical plant and/or process technology modifications made to mold the main processes-concentrate leaching and filtering, autoclaving and filtration of by-products, and crystallization of salt cake-into an effective, economic operation.IntroductionEquity Silver Mines Limited, a member of the Placer Development Group, owns and operates an open-pit silver mine and related facilities located 37 kilometres southeast of Houston in north-central British Columbia. The mine occupies a 44 I-hectare (1089 acre) site at an elevation of 1300 metres (4265 feet) on the Nechako Plateau. Producing a copper concentrate containing high values of silver and gold, it is the largest silver mine in Canada and one of the largest in the western world. Equity stresses open communications, positive motivation, and production with safety, and achieved the best mine safety record in western Canada in 1984."

Jan 1, 1985

By P. Amelunxen

It is well-known that the particle breakage mode that occurs in a semi-autogenous mill is significantly different from that which occurs in a ball mill, enough so to warrant very different lab scale breakage tests and scale-up models. This phenomenon, at the plant scale, leads to changing process constraints depending on the particular properties of the ore. For example, hard or coarse ores might bottleneck the SAG/AG mill throughput, while the ball mills might constrain throughput when milling soft or fine ores. Because the power draw of a ball mill is fairly constant compared to that of a SAG/AG mill, periods of SAG/AG mill bottlenecks lead to increased ball mill circuit specific energy consumption and a finer grinding circuit product size, which together constitute a loss of efficiency of the overall process. Because HPGR circuit throughput is less sensitive to changes in ore hardness, this situation is less common or severe in those circuits. Furthermore, the ball mills are somewhat decoupled from the upstream crushing circuits through the use of surge bins, which also helps to mitigate this effect. As a result, ore hardness variability constitutes a significant cost penalty that should be applied to SAG mill/ball mill/pebble crusher SABC circuits when evaluating the relative economics of different grinding circuit configurations. Nevertheless, the issue is by-and-large ignored, because most current HPGR trade-off studies are based on averaged ore hardness parameters. This paper provides an estimate of the magnitude of this penalty for a typical operation by using Monte Carlo simulation methods and plant data from Freeport-McMoRan?s autogenous, semi-autogenous, and HPGR-based comminution circuits. A case study from an in-house 96K t/d sulphide project is presented to illustrate the concept. It was found that by including variability effects, the trade-off NPV of the HPGR circuit over that of the SAG mill circuit increases to $84 million from negative $33 million, effectively reversing the original decision of selecting a SAG mill circuit for the fixed hardness case.

Jan 1, 2012

By G. M. Dunn

Pressure leach autoclave circuits are employed in the leaching of ores, concentrates, mattes, alloys and intermediates for the recovery of metals into solution. Once the metals are extracted into solution the value metals can be recovered by hydrometallurgical means such as by purification followed by electrowinning, hydrogen reduction, pyrohydrolysis, crystallisation and other unit operations. In many of these integrated flowsheets the pressure leach step is pivotal to the recovery of the value metals from the host material. In an expansion or a new project, a large component of the capital cost can be associated with the pressure leach step and process engineers frequently look for opportunities to mitigate costs. This paper examines a new route for increasing the capacity of an exothermic pressure oxidation leach for sulphide concentrates, sulphide and phosphide mattes and alloys.

Jan 1, 2004