Search Documents

By J Zhou, D M. Hunter, S M. Iveson, K P. Galvin

The recovery and concentration of ultra-fine iron ore can provide significant economic benefits. Presently, there are limited options available given the low settling rates achieved by conventional gravity separation and the relatively poor performance of reverse flotation. The Reflux Classifier is a new water-based gravity separation technology that consists of a set of parallel inclined channels positioned above a vertical fluidised section. This arrangement promotes a powerful throughput advantage compared to conventional fluidisation and a highly selective hydrodynamic basis for achieving sharp separations. A high shear rate develops within the inclined channels, which generates sufficient hydrodynamic lift to convey the lower-density particles (even if they are relatively coarse) to overflow while retaining the high-density particles (even those that are ultra-fine) for discharge to the underflow. The technology has previously been used around the world on particle sizes in excess of 0.1 mm. The present work, however, is concerned with density-based separations down to much finer particle sizes approaching 0.01 mm.A major advantage of the Reflux Classifier technology is the achievement of simultaneous gravity separation and desliming via a single-stage separation. A series of continuous experiments was conducted using an iron ore feed with head grade of 35 wt per cent FeT and nominal top size of 0.106 mm, with 59 wt per cent being below 0.038 mm in size. At a low throughput of 1.5 t/(m2 h), the Reflux Classifier produced high-grade products at a high recovery. For the entire feed, grades of 66.1 wt per cent FeT with Fe recoveries of 80 per cent were achieved in a single-stage separation. Within the 0.020–0.038 mm size fraction, grades of 68.8 per cent were achieved with iron recoveries of 94.7 per cent. Excellent recoveries of up to 57.0 per cent were achieved for the -0.020 mm size fraction. The ability of the inclined channels to retain the fine dense material further enhances the effectiveness of the Reflux Classifier by creating an autogenous dense medium effect within the vertical section. This helps to elevate large gangue particles up into the overflow.CITATION:Hunter, D M, Zhou, J, Iveson, S M and Galvin, K P, 2015. Gravity separation of ultra-fine iron ore in the reflux classifier, in Proceedings Iron Ore 2015, pp 143–148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By D Asahina, T Endo, H Hosono, T Takemura

Changes in the stress field around faults due to the excavation of underground space or the extraction of underground resources induce fault reactivation. To understand the mechanism of fault reactivation, it is important to observe the deformation and sliding processes of the asperities, which is regionally contacted areas at the fault planes. In the laboratory, triaxial compression tests are commonly conducted to reproduce the stress conditions around faults and study their mechanical behaviours. The conventional measurement devices for triaxial compression testing (eg load cells, local deformation transducers, and piezoelectric sensors) uses sensors to measure changes in the physical properties of rocks, but the direct visual information for the sample condition inside the pressure vessel is limited and can only be estimated from the sample after the experiment. We recently developed a direct visual measurement system to observe the slip behaviour of rocks from the inside of the pressure vessel of a triaxial test apparatus. This paper introduces this visual measurement system and presents some preliminary experimental results. The visual measurement system consists of a steel housing with a built-in commercially available digital camera. The triaxial compression tests were conducted to visually observe the sliding behaviour of the pre-cut specimens and to measure its behaviour through the digital image correlation (DIC) method. The captured images and the DIC results show the displacement field of the specimens for different confining pressure. We verified the sliding behaviour and the failure at/around the triangular asperity under at different confining pressure.

Nov 29, 2022

By W Ilahi

Underground metalliferous mining methods often result in the formation of vertical openings to facilitate the extraction of orebodies. These development and production techniques can result in the creation of vertical open voids, which include stopes, orepasses, ventilation raises and other excavations. There are risks associated with the use of mobile plant in the vicinity of these voids, especially during backfilling and when bunds are constructed at the edge of a stope or void. These voids can present unacceptable risks if not adequately managed.

May 5, 2022

By K Koskinen, S Ronkainen

The flow field induced in an Outokumpu TankCell and by an OK rotor-stator mixing device in a laboratory and a process size flotation cell was modelled numerically using computational fluid dynamics (CFD). The primary target was to discover and reproduce the various interactions between the flow field and the flotation cell by numerical means. As power consumption depends sensitively on flow field, it can be regarded as a top-level derived quantity (or measure/metric) indicating the validity of the numerically obtained flow field. Having properly validated numerical means to produce the flow field the influence of various design parameters can be captured with certain accuracy. In addition, separate gas and solid phase models for bubbles and solids, respectively, were implemented. The comparisons between velocities and turbulence quantities measured using the laser doppler velocimetry (LDV) technique and CFD modelling were performed. The grid generation was performed with the commercial Gambit 1.3 and the subsequent integration and solving of the resulting algebraic equations with the commercial CFD-code Fluent 6.22. The computationally economic multiple reference frame method was included to model the moving rotor blades. Gas and solid phase models were modified mixture models.

Jan 1, 2005

By A Purchase, C Stacey

The procedure for operation of deluge systems installed in road tunnels is still a subject of debate. The work undertaken in this paper assists in the understanding of the effects of deluge in road tunnels, and thus aims to help inform the development of operational policy. Analysis was undertaken using computational fluid dynamics (CFD) simulations to help explore the deluge interaction with the tunnel ventilation (including smoke exhaust) and combustion products. It was found, for the scenarios considered, that: Deluge activation can decrease the required critical velocity for smoke backlayering, and this in turn can improve the effectiveness of a smoke exhaust system.The dominant parameter for deluge effectiveness is the vehicle configuration, with shielded scenarios (such as a fire in the passenger compartment) showing almost no water reaching the fire. The water delivery rate (5 mm/min versus 10 mm/min) has only a minor effect on the smoke duct damper inlet temperatures and downstream smoke temperatures for small fires (5 MW). For large fires (50 MW) the higher water delivery rate gives slightly improved performance (lower damper inlet temperatures and lower downstream smoke temperatures). A one-dimensional transient tunnel model incorporating different operational and deluge response policies (ie deluge activation times) was developed. It was used to examine the influence of different operational parameters on life safety risk and tunnel damage risk. It was found, for the scenarios considered, that: The life safety risk for different scenarios has a sensitivity to deluge activation policy with the case of delaying the deluge activation for a long time giving the worst outcomes. However, the most critical parameters for life safety risk are operator response time (for all response activities, not just deluge) and the type of fire (configuration, size and growth rate).There is a reduction in risk of tunnel damage when the deluge is activated earlier, although the fire configuration (ie whether or not the seat of the fire can be reached) has the greatest influence on the outcome. It is concluded that the deluge activation policy should be case-dependent. It will depend on the tunnel, the safety systems provided, and most particularly the vehicles involved. The current policy in Australian tunnels is for manual activation of the deluge by the tunnel operator as soon as practical after the fire is confirmed (see also PIARC, 2007). This is a good policy. However, future work may be helpful to improve the skills of operators to make the best judgement as to when deluge should be activated, balancing all risks. This work could include research to further the understanding of deluge and fire in road tunnels, training programs and consideration of historical fire events.

Jan 1, 2008

Five types of mineral resource were known in the sedimentary cover of the oceans and seas floors prior to the 1980's :1) hydrocarbon fields including some very large zones of oil and gas accumulation; 2) "Red Sea" type thermal oozes with increased concentrations of noble metals; 3) ferromanganese nodules; 4) concentrations of metallic sulphides ("Black Smokers"); and 5) cobalt-bearing ferromanganese crusts on the summits and slopes of seamounts. Since then, the so called "White Smokers", containing sulphides of copper and zinc, have been discovered. The ore horizons (manganese, copper, nickel and other metals) of the sedimentary cover of deep-sea basins comprise a sixth type of mineral resource in the oceans. These horizons have not only a theoretical, but also a principal economic significance

Jan 1, 1995

By S K. Ray

Open fire in a mine gallery causes large-scale damage to property and sometimes precious lives. Such fires produce two distinct effects, the throttle effect and the buoyancy effect. These effects disturb the ventilation system of the mine. To understand the complex dynamic phenomenon of open fire and its effect on ventilation systems, a mine fire model gallery has been designed and constructed at Central Mining Research Institute, Dhanbad. Two sets of experiments at air velocities of 1 and 1.5 m/s were conducted in the gallery using coal samples from the Dobrana seam of the Raniganj coalfields. After about an hour of development of fully-fledged fire, heavy backlash, with smoke and fumes, was observed. At the time of backlash occurring the gallery was divided into two zones. In the region of the gallery from the base up to 1.4 m the airflow was normal, in the remaining upper portion the airflow was the reverse. Air quantity reduced substantially, while pressure dropped across the fire zone, the products of combustion (POC) and temperature increased during the period of the throttle effect. It has been revealed from these studies that with an increase in airflow, pressure drops across the fire zone, POC, temperature and reduction in airflow increases. This paper addresses the important design features of the gallery, the instrumentation system, the experimental procedure and assesses the effect of open fires on mine ventilation systems.

Jan 1, 2005

It has been clearly demonstrated in both the first, as well as in the last world conflict, that a nation's ability to wage as well as win a war is primarily a function of its industrial, and particularly its steel making capacity, provided both are directed to munition production.The Axis gambled on their pre-war policy of bullets before butter giving them sufficient initial advantage to decide the issue before the Allies had time to gear their industries to war production.Fortunately for us, Hitler and his advisers apparently underestimated Russia's war potential, although they must have known that Russia was, in 1939, the third largest steel making country in the world, as shown by the following figures:

Jan 1, 1947

By S Yang, J Wang, J G. Ning

A series of conventional dynamic uniaxial compression (CDUC) tests and coupled static-dynamic loading (CSDL) tests were conducted using a split Hopkinson pressure bar (SHPB) system to explore the dynamic mechanical behaviour and fracture characteristics of medium sandstone on a microscale in the laboratory. In the CDUC tests, the dynamic uniaxial compressive strength of the medium sandstone was rate-dependent, while the dynamic elastic modulus was not dependent on the strain rate. Then, we proposed a generalised model to characterise the rate-dependent strength from 17.5 s-1 to 96.8 s-1. In the CSDL tests, with increasing initial pre-static stress, the dynamic elastic modulus and dynamic strength increased nonlinearly at first and then decreased. The results show that two classical mechanical types (ie Class I and Class II) are observed from the dynamic stress-strain responses of the CDUC and CSDL tests. By means of scanning electron microscopy (SEM), the micro difference of post-loading microfracture characteristics in Class I and Class II behaviour was identified. In Class I behaviour, intergranular fracture (IF) usually initiates at or near the grains, most cracks deflected along the grain boundaries, resulting in a sharp angular edge, then coalesces to the main fracture surface that splits the specimen along the direction of stress wave propagation. In contrast, Class II behaviour results from the combined IF and transgranular fracture (TF).

Nov 29, 2022

Blasting effectiveness must be gauged by total production costs. ANFO charges made up in polythene "sausages" are not as profitable as is indicated by the price of ANFO. All-slurry charges are warranted only where blastholes cannot be dewatered effectively, or where drilling costs are very high. An increase in blasthole diameter leads to coarser fragmentation. This effect is most pronounced in tough and massive or blocky strata, or in ground which consists of unfissured boulders in a softer matrix. When ANFO and some slurry-type charges of small diameter are used in plastic-acting ground, charges may fail to detonate through precompression by charges fired on an earlier delay. The optimum blasthole length is rarely less than four times the burden distance. For best results, blastholes should be inclined to the vertical and parallel to the face. Nominal burdens and spacings are often altered radically by the initiation sequence. For best fragmentation, all blastholes must have good effective faces, and should be effectively stagg- ered with an actual spacing:burden ratio in the approximate range 2.0-5.0.

Jan 1, 1975

By Wallman D

Since 1981 two single entry roadways have been driven at Ellalong Colliery for a total distance of 1 030 metres. They were driven at a height of 1.73 metres within the 3.7 metres thick Greta Seam using a Dosco In-Seam Miner (I.S.M.). Ventilation of the drivage was accomplish- ed by an exhausting fan in series with steel ducting and flexible ducting in the immediate face area. The air quantities provided at the face were more than adequate to comply with the requirements of -the auxiliary fan rules and the Coal Mines Regulation Act, 1912, as amended. The experience gained in these drivages demonstrated that the ventilation of long single entry headings can be practically and safely achieved using existing equipment.

Jan 1, 1983

By Cunneen R. D, Murray A. M

Exploration in the vicinity of the abandoned Mt Coolon mine has shown that the shape and attitude of the quartz lode is controlled by the interaction between the lode and a converging syncline. Gold grades within the lode are enhanced along intersections with a welded ignimbrite, and decline rapidly where the lode intersects unwelded ignimbrite. Mineralogy and textures indicate the vein has an epithermal origin modified by a later intrusive event.

Jan 1, 1989

By M D. Griffith

Oct 12, 2022

By D J. Williams, A Shokouhi, A Naderian

Extracting alumina from bauxite involves the production of fine-grained waste known as red mud. The highly alkaline red mud is usually neutralised by applying sea water, thickened to between 25% and 30% solids by mass, before disposal to a Tailing Storage Facility (TSF). Hydraulic sorting, settling, self-weight consolidation, and desiccation are the processes contributing to the overall volume change of the red mud after deposition. Investigating the effect of these processes on the volume change behaviour of the fine-grained red mud is an important step in the estimation of the required storage volume of the storage facilities. This paper presents the results of a series of laboratory consolidation tests in a slurry consolidometer, and comparisons are made with field testing and observations.CITATION:Shokouhi, A, Naderian, A and Williams, D J, 2018. Assessing the volume change behaviour of red mud through laboratory and field testing, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 309–316 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By I Neilsen, A Walker, A Hooper

Final landform planning in Deswik software was used to determine if integration into the mine plans could achieve better closure outcomes. Using the dump surface outputs from the Deswik Landform and Haulage Simulation (LHS) and the Reshape Landform tool, the project intended to:1.Review costs to achieve the final landform for several grade criteria scenarios;2.Quantify reshape volumes at several stages of the mines development with the objective to contribute to margin ranking inputs; and3.Identify rehabilitation cost reduction measures such as backfilling ramps and pits.CITATION:Neilsen, I, Walker, A and Hooper, A, 2018. Case studies for integrating rehabilitation planning with mine planning in strip mining, in Proceedings Life-of-Mine 2018, pp 93–95 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By Bigdy D. N

The paper describes a system for providing mine management with a continuous indication of the effectivness of longwall coalface powered supports in controlling roof-to-floor convergence. The system comprises on-face instrumentation monitoring convergence and support leg circuit pressures, a means of transmitting the output of that instrumentation to the surface for collection, and software which presents both a condensed analysis for rapid review of the current state, and extended analyses from which remedial action can be recommended if a problem is identified. The results of a field trial are presented showing that meaningful results can be obtained.

Jan 1, 1988

By G L. Boyd

Backfill applied to highwall mining is foreseen as a means to increase recovery of mineable coal to levels comparable with underground longwall mining. This paper describes the progress of research to demonstrate the role required of backfill to achieve real increases in coal recovered by highwall mining methods.

Jan 1, 1998

By Abishev D. N, Balakirev V. F, Davydov G. I

The problem of recovery of cobalt products from poorly oxidised nickel ores (Kempirsaisk deposit) and pyrite concentrates with a low content of cobalt (Sokolovsk-Sarbaisky deposit) has not been solved to the present time in Kazakstan. The balance reserves of nickel ore of the Kempirsaisky deposit make up more than 35 million tons with a nickel content of 1.13 per cent and cobalt content of 0.05 per cent; besides there are 110 millions tons of out-balance ores (Anon, 1995). In a tailing dump of Sokolovsk-Sarbaisk Mining and Productional Association more than 320 million tons of tailings of wet magnetic separation have accumulated, which contain 7.2 per cent of sulphur, 0.022 per cent of cobalt, 0.012 per cent of nickel, 0.094 per cent of copper, 0.079 per cent of zinc, 16.45 per cent of iron, and from which a high quality pyrite concentrate car) he separated through flotation, containing 48 - 50 per cent of sulphur, 44.15 per cent of iron, 0.141 per cent of cobalt, 0.07 per cent of nickel, and 0.10 per cent of copper. The well-known technological flow charts for cobalt and nickel recovery from the tailings of sulphide-magnetite ores dressing (to give pyrite concentrate) and from oxidised nickel ores, are not profitable at the existing prices for metals, but are not worthless and require significant capital investments for the realisation of their value. The flow chart `sulphate roasting - leaching - solution processing' is used widely for combined processing of cobalt-containing pyrite ores and concentrates.

Jan 1, 1996

By S R. Grano

The selection of the proper frother, specifically for a given ore, is essential in flotation. Traditionally, strong and stable froths are required in the scavengers, where metal recovery needs to be maximised, while selectivity must be achieved in the roughers and cleaners, where grade of concentrates is the main issue. The physical properties of a froth are determined both by frother type, by process water composition and by the amount and nature of the suspended particles. The evaluation of different frothers, in terms of metallurgical performance, is complicated at plant scale, since it may lead to periods of malfunctioning of the process and unacceptable decreases in recovery. On the other hand, evaluation based on frother chemistry only, is often unsatisfactory, because the frothing response is strongly ore dependent. A procedure, and proper tools, was developed at the Wark in order to perform the screening of candidate frothers at batch scale on real pulp samples. The main parameters related to froth stability (half-life time, froth height) are measured after introducing the pulp samples into a foaming column, where different conditions in terms of frother addition, agitation and aeration can be maintained. The approach has been applied to the selection of frothers for the flotation of an Australian sulfide ore. Procedure and results are discussed.

Jan 1, 2006

By P Khalkho, M Singh

Rock masses when subjected to uniaxial or triaxial cyclic loading (eg in hydraulic running tunnels, during retrieval and injection of oil and gas from storage underground caverns and haulage roads), the material has a tendency to fail in fatigue. In order to design safe and reliable underground structures, the determination of brittleness under such loading conditions becomes a pre-requisite. Brittleness influences strongly the failure process and makes the rock mass behaviour complex under different tunnelling and mining activities. Brittleness Index is a term to quantify the brittleness feature of a specimen. In the present study, an attempt has been made to quantify the brittleness of jointed specimens using different brittleness criteria. The joints of the model jointed specimens were oriented at an angle of θ=15° normal to the loading direction, each having three different JRC’s=2–4, 12–14 and 14–16. The specimens were tested under triaxial conditions in incremental complete cyclic test scheme performed at displacement-controlled mode. Different brittleness criteria were used ie stress-strain dependent brittleness index, Young Modulus approach and energy-balance based mechanism. It was observed that energy-balance based mechanism which consider the post failure behaviour is more descriptive to reflect the whole variation of brittleness from sheer brittleness to ductility.

Nov 29, 2022